Manual merge of arch/powerpc/kernel/smp.c and add missing scheduler_ipi()
call to arch/powerpc/platforms/cell/interrupt.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since there are only 4 messages, we can replace the atomic bit set
(which uses atomic load reserve and store conditional sequence) with
a byte stores to seperate bytes. We still have to perform a load
reserve and store conditional sequence to avoid loosing messages on
reception but we can do that with a single call to xchg.
The do {} while and __BIG_ENDIAN specific mask testing was chosen by
looking at the generated asm code. On gcc-4.4, the bit masking becomes
a simple bit mask and test of the register returned from xchg without
storing and loading the value to the stack like attempts with a union
of bytes and an int (or worse, loading single bit constants from the
constant pool into non-voliatle registers that had to be preseved on
the stack). The do {} while avoids an unconditional branch to the
end of the loop to test the entry / repeat condition of a while loop
and instead optimises for the expected single iteration of the loop.
We have a full mb() at the beginning to cover ordering between send,
ipi, and receive so we can use xchg_local and forgo the further
acquire and release barriers of xchg.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Compile the new smp ipi mux and demux code only if a platform
will make use of it. The new config is selected as required.
The new cause_ipi smp op is only available conditionally to point out
configs where the select is required; this makes setting the op an
immediate fail instead of a deferred unresolved symbol at link.
This also creates a new config for power surge powermac upgrade support
that can be disabled in expert mode but is default on.
I also removed the depends / default y on CONFIG_XICS since it is selected
by PSERIES.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Consolidate the mux and demux of ipi messages into smp.c and call
a new smp_ops callback to actually trigger the ipi.
The powerpc architecture code is optimised for having 4 distinct
ipi triggers, which are mapped to 4 distinct messages (ipi many, ipi
single, scheduler ipi, and enter debugger). However, several interrupt
controllers only provide a single software triggered interrupt that
can be delivered to each cpu. To resolve this limitation, each smp_ops
implementation created a per-cpu variable that is manipulated with atomic
bitops. Since these lines will be contended they are optimialy marked as
shared_aligned and take a full cache line for each cpu. Distro kernels
may have 2 or 3 of these in their config, each taking per-cpu space
even though at most one will be in use.
This consolidation removes smp_message_recv and replaces the single call
actions cases with direct calls from the common message recognition loop.
The complicated debugger ipi case with its muxed crash handling code is
moved to debug_ipi_action which is now called from the demux code (instead
of the multi-message action calling smp_message_recv).
I put a call to reschedule_action to increase the likelyhood of correctly
merging the anticipated scheduler_ipi() hook coming from the scheduler
tree; that single required call can be inlined later.
The actual message decode is a copy of the old pseries xics code with its
memory barriers and cache line spacing, augmented with a per-cpu unsigned
long based on the book-e doorbell code. The optional data is set via a
callback from the implementation and is passed to the new cause-ipi hook
along with the logical cpu number. While currently only the doorbell
implemntation uses this data it should be almost zero cost to retrieve and
pass it -- it adds a single register load for the argument from the same
cache line to which we just completed a store and the register is dead
on return from the call. I extended the data element from unsigned int
to unsigned long in case some other code wanted to associate a pointer.
The doorbell check_self is replaced by a call to smp_muxed_ipi_resend,
conditioned on the CPU_DBELL feature. The ifdef guard could be relaxed
to CONFIG_SMP but I left it with BOOKE for now.
Also, the doorbell interrupt vector for book-e was not calling irq_enter
and irq_exit, which throws off cpu accounting and causes code to not
realize it is running in interrupt context. Add the missing calls.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only user of MSG_ALL_BUT_SELF in the whole kernel tree is powerpc,
and it only uses it to start the debugger. Both debuggers always call
smp_send_debugger_break with MSG_ALL_BUT_SELF, and only mpic can do
anything more optimal than a loop over all online cpus, but all message
passing implementations have to code for this special delivery target.
Convert smp_send_debugger_break to take void and loop calling the smp_ops
message_pass function for each of the other cpus in the online cpumask.
Use raw_smp_processor_id() because we are either entering the debugger
or trying to start kdump and the additional warning it not useful were
it to trigger.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit c56e58537d breaks SMP support in PPC_47x chip.
secondary_ti must be set to current thread info before callin kick_cpu or else
start_secondary_47x will jump into void when trying to return to c-code.
In the current setup secondary_ti is initialized before the CPU idle task is started
and only the boot core will start. I am not sure this is the correct solution, but it
makes SMP possible in my chip.
Note! The HOTPLUG support probably need some fixing to, There is no trampoline code
available in head_44x.S - start_secondary_resume?
Signed-off-by: Kerstin Jonsson <kerstin.jonsson@ericsson.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adapt new API.
Almost change is trivial. Most important change is the below line
because we plan to change task->cpus_allowed implementation.
- ctx->cpus_allowed = current->cpus_allowed;
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we start a cpu we use smp_ops->kick_cpu(), which currently
returns void, it should be able to fail. Convert it to return
int, and update all uses.
Convert all the current error cases to return -ENOENT, which is
what would eventually be returned by __cpu_up() currently when
it doesn't detect the cpu as coming up in time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For future rework of try_to_wake_up() we'd like to push part of that
function onto the CPU the task is actually going to run on.
In order to do so we need a generic callback from the existing scheduler IPI.
This patch introduces such a generic callback: scheduler_ipi() and
implements it as a NOP.
BenH notes: PowerPC might use this IPI on offline CPUs under rare conditions!
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110405152728.744338123@chello.nl
Instead of creating idle threads at boot for all possible CPUs, we
create them on demand, like x86 or ARM, and we properly call init_idle
to re-initialize an idle thread when a CPU was unplugged and is now
re-plugged.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead, keep it static, expose an accessor and use that from
the PowerMac code. Avoids easy namespace collisions and will
make it easier to consolidate with other implementations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This allows us to stop abusing smp_ops->setup_cpu() for cleanup
tasks that have to take place after the initial boot time CPU
bringup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the last remnants of cpu_enable(), everybody uses the normal
__cpu_up() path now
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is used by some "soft" hotplug implementations. I needs to
call idle_task_exit() when the CPU is going away, and we remove
the now no-longer needed set_cpu_online() and local_irq_enable()
which are handled by the return to start_secondary
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Various thing are torn down when a CPU is hot-unplugged. That CPU
is expected to go back to start_secondary when re-plugged to re
initialize everything, such as clock sources, maps, ...
Some implementations just return from cpu_die() callback
in the idle loop when the CPU is "re-plugged". This is not enough.
We fix it using a little asm trampoline which resets the stack
and calls back into start_secondary as if we were all fresh from
boot. The trampoline already existed on ppc64, but we add it for
ppc32
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These APIs take logical cpu number as input
Change cpu_first_thread_in_core() to cpu_first_thread_sibling()
Change cpu_last_thread_in_core() to cpu_last_thread_sibling()
These APIs convert core number (index) to logical cpu/thread numbers
Add cpu_first_thread_of_core(int core)
Changed cpu_thread_to_core() to cpu_core_index_of_thread(int cpu)
The goal is to make 'threads_per_core' accessible to the
pseries_energy module. Instead of making an API to read
threads_per_core, this is a higher level wrapper function to
convert from logical cpu number to core number.
The current APIs cpu_first_thread_in_core() and
cpu_last_thread_in_core() returns logical CPU number while
cpu_thread_to_core() returns core number or index which is
not a logical CPU number. The new APIs are now clearly named to
distinguish 'core number' versus first and last 'logical cpu
number' in that core.
The new APIs cpu_{first,last}_thread_sibling() work on
logical cpu numbers. While cpu_first_thread_of_core() and
cpu_core_index_of_thread() work on core index.
Example usage: (4 threads per core system)
cpu_first_thread_sibling(5) = 4
cpu_last_thread_sibling(5) = 7
cpu_core_index_of_thread(5) = 1
cpu_first_thread_of_core(1) = 4
cpu_core_index_of_thread() is used in cpu_to_drc_index() in the
module and cpu_first_thread_of_core() is used in
drc_index_to_cpu() in the module.
Make API changes to few callers. Export symbols for use in modules.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, when CONFIG_VIRT_CPU_ACCOUNTING is enabled, we use the
PURR register for measuring the user and system time used by
processes, as well as other related times such as hardirq and
softirq times. This turns out to be quite confusing for users
because it means that a program will often be measured as taking
less time when run on a multi-threaded processor (SMT2 or SMT4 mode)
than it does when run on a single-threaded processor (ST mode), even
though the program takes longer to finish. The discrepancy is
accounted for as stolen time, which is also confusing, particularly
when there are no other partitions running.
This changes the accounting to use the timebase instead, meaning that
the reported user and system times are the actual number of real-time
seconds that the program was executing on the processor thread,
regardless of which SMT mode the processor is in. Thus a program will
generally show greater user and system times when run on a
multi-threaded processor than on a single-threaded processor.
On pSeries systems on POWER5 or later processors, we measure the
stolen time (time when this partition wasn't running) using the
hypervisor dispatch trace log. We check for new entries in the
log on every entry from user mode and on every transition from
kernel process context to soft or hard IRQ context (i.e. when
account_system_vtime() gets called). So that we can correctly
distinguish time stolen from user time and time stolen from system
time, without having to check the log on every exit to user mode,
we store separate timestamps for exit to user mode and entry from
user mode.
On systems that have a SPURR (POWER6 and POWER7), we read the SPURR
in account_system_vtime() (as before), and then apportion the SPURR
ticks since the last time we read it between scaled user time and
scaled system time according to the relative proportions of user
time and system time over the same interval. This avoids having to
read the SPURR on every kernel entry and exit. On systems that have
PURR but not SPURR (i.e., POWER5), we do the same using the PURR
rather than the SPURR.
This disables the DTL user interface in /sys/debug/kernel/powerpc/dtl
for now since it conflicts with the use of the dispatch trace log
by the time accounting code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simple cleanup by moving arch_sd_sibling_asym_packing from process.c to
smp.c to save an #ifdef CONFIG_SMP
No functionality change.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During CPU offline/online tests __cpu_up would flood the logs with
the following message:
Processor 0 found.
This provides no useful information to the user as there is no context
provided, and since the operation was a success (to this point) it is expected
that the CPU will come back online, providing all the feedback necessary.
Change the "Processor found" message to DBG() similar to other such messages in
the same function. Also, add an appropriate log level for the "Processor is
stuck" message.
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Acked-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nathan Fontenot <nfont@austin.ibm.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We already defined start_cpu_decrementer() to invoke decrementer for AP as
the following path:
start_secondary() -> secondary_cpu_time_init() -> start_cpu_decrementer()
So remove these incorrect codes introduced from commit:
e7f75ad0 powerpc/47x: Base ppc476 support
And actually we really should not enable decrementer before calling set_dec().
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the decrementer and timekeeping code was moved over to using
the generic clockevents and timekeeping infrastructure, several
variables and functions have been obsolete and effectively unused.
This deletes them.
In particular, wakeup_decrementer() is no longer needed since the
generic code reprograms the decrementer as part of the process of
resuming the timekeeping code, which happens during sysdev resume.
Thus the wakeup_decrementer calls in the suspend_enter methods for
52xx platforms have been removed. The call in the powermac cpu
frequency change code has been replaced by set_dec(1), which will
cause a timer interrupt as soon as interrupts are enabled, and the
generic code will then reprogram the decrementer with the correct
value.
This also simplifies the generic_suspend_en/disable_irqs functions
and makes them static since they are not referenced outside time.c.
The preempt_enable/disable calls are removed because the generic
code has disabled all but the boot cpu at the point where these
functions are called, so we can't be moved to another cpu.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Configuring a powerpc 32 bit kernel for both SMP and SUSPEND turns on
CPU_HOTPLUG to enable disable_nonboot_cpus to be called by the common
suspend code. Previously the definition of cpu_die for ppc32 was in
the powermac platform code, causing it to be undefined if that platform
as not selected.
arch/powerpc/kernel/built-in.o: In function 'cpu_idle':
arch/powerpc/kernel/idle.c:98: undefined reference to 'cpu_die'
Move the code from setup_64 to smp.c and rename the power mac
versions to their specific names.
Note that this does not setup the cpu_die pointers in either
smp_ops (request a given cpu die) or ppc_md (make this cpu die),
for other platforms but there are generic versions in smp.c.
Reported-by: Matt Sealey <matt@genesi-usa.com>
Reported-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the *_map cpumask variants are deprecated, change the comments to
instead refer to *_mask.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dynamically allocate cpu_sibling_map and cpu_core_map cpumasks.
We don't need to set_cpu_online() the boot cpu in smp_prepare_boot_cpu,
init/main.c does it for us.
We also postpone setting of the boot cpu in cpu_sibling_map and cpu_core_map
until when the memory allocator is available (smp_prepare_cpus), similar
to x86.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use new cpumask_* functions, and dynamically allocate cpumask in fixup_irqs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the new cpumask_* functions and dynamically allocate the cpumask in
smp_cpus_done.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds the base support for the 476 processor. The code was
primarily written by Ben Herrenschmidt and Torez Smith, but I've been
maintaining it for a while.
The goal is to have a single binary that will run on 44x and 47x, but
we still have some details to work out. The biggest is that the L1 cache
line size differs on the two platforms, but it's currently a compile-time
option.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Use set_cpus_allowed_ptr rather than set_cpus_allowed.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1,E2;
@@
- set_cpus_allowed(E1, cpumask_of_cpu(E2))
+ set_cpus_allowed_ptr(E1, cpumask_of(E2))
@@
expression E;
identifier I;
@@
- set_cpus_allowed(E, I)
+ set_cpus_allowed_ptr(E, &I)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move the defintion and lock helper routines for the cpu hotplug driver
lock from pseries to powerpc code to avoid build breaks for platforms
other than pseries that use cpu hotplug.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
Remove the CPU from the online map to prevent smp_call_function
from sending messages to a stopped CPU.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates percpu related symbols in powerpc such that percpu
symbols are unique and don't clash with local symbols. This serves
two purposes of decreasing the possibility of global percpu symbol
collision and allowing dropping per_cpu__ prefix from percpu symbols.
* arch/powerpc/kernel/perf_callchain.c: s/callchain/cpu_perf_callchain/
* arch/powerpc/kernel/setup-common.c: s/pvr/cpu_pvr/
* arch/powerpc/platforms/pseries/dtl.c: s/dtl/cpu_dtl/
* arch/powerpc/platforms/cell/interrupt.c: s/iic/cpu_iic/
Partly based on Rusty Russell's "alloc_percpu: rename percpu vars
which cause name clashes" patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@ozlabs.org
Use the accessors rather than frobbing bits directly (the new versions
are const).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
We're weaning the core code off handing cpumask's around on-stack.
This introduces arch_send_call_function_ipi_mask(), and by defining
it, the old arch_send_call_function_ipi is defined by the core code.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The following commit introduced a compile error since it removed
the implementation of smp_85xx_basic_setup:
commit 77c0a700c1
Author: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Fri Aug 28 14:25:04 2009 +1000
powerpc: Properly start decrementer on BookE secondary CPUs
Make it so that smp_ops probe() and setup_cpu() can be set to NULL.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Time time taken for a single cpu online operation on a pseries machine
is as follows:
Dedicated LPAR (POWER6): ~220ms.
Shared LPAR (POWER5) : ~240ms.
Of this time, approximately 200ms is taken up by __cpu_up(). This is because
we poll every 200ms to check if the new cpu has notified it's presence
through the cpu_callin_map. We repeat this operation until the new cpu sets
the value in cpu_callin_map or 5 seconds elapse, whichever comes earlier.
However, using completion_structs instead of polling loops,
the time taken by the new processor to indicate it's presence has
found to be less than 1ms on pseries. This method however may not
work on all powerpc platforms due to the time-base synchronization code.
Keeping this in mind, we could reduce msleep polling interval from
200ms to 1ms while retaining the 5 second timeout.
With this, the time taken for a cpu online operation changes as follows:
Dedicated LPAR (POWER6): 20-25ms.
Shared LPAR (POWER5) : 60-80ms.
In both these cases, it was found that the code polls through the loop
only once indicating that 1ms is a reasonable value, atleast on pseries.
The code needs testing on other powerpc platforms.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The old PowerSurge SMP (ie, dual or quad 604 machines) code has
numerous issues in modern world.
One is cpu_possible_map is set too late (the device-tree is bogus)
so we fail to allocate the interrupt stacks and crash. Another
problem is the fact the timebase is frozen by the bringup of the
second CPU so the delays in the generic code will hang, we need
to move some of the calling procedure to inside the powermac code.
This makes it boot again for me
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
The smp code uses cache information to populate cpu_core_map; change
it to use common code for cache lookup.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
smp_hw_index isn't used on 64-bit, so move it from smp.c to
setup_32.c.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Impact: cleanup
Each SMP arch defines these themselves. Move them to a central
location.
Twists:
1) Some archs (m32, parisc, s390) set possible_map to all 1, so we add a
CONFIG_INIT_ALL_POSSIBLE for this rather than break them.
2) mips and sparc32 '#define cpu_possible_map phys_cpu_present_map'.
Those archs simply have phys_cpu_present_map replaced everywhere.
3) Alpha defined cpu_possible_map to cpu_present_map; this is tricky
so I just manipulate them both in sync.
4) IA64, cris and m32r have gratuitous 'extern cpumask_t cpu_possible_map'
declarations.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Mike Travis <travis@sgi.com>
Cc: ink@jurassic.park.msu.ru
Cc: rmk@arm.linux.org.uk
Cc: starvik@axis.com
Cc: tony.luck@intel.com
Cc: takata@linux-m32r.org
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: paulus@samba.org
Cc: schwidefsky@de.ibm.com
Cc: lethal@linux-sh.org
Cc: wli@holomorphy.com
Cc: davem@davemloft.net
Cc: jdike@addtoit.com
Cc: mingo@redhat.com
With the new generic smp call function helpers, I noticed the code in
smp_message_recv was a single function call in many cases. While
getting the message number from the ipi data is easy, we can reduce
the path length by a function and data-dependent switch by registering
seperate IPI actions for these simple calls.
Originally I left the ipi action array exposed, but then I realized the
registration code should be common too.
The three users each had their own name array, so I made a fourth
to convert all users to use a common one.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The comment in the code was asking "Do we have to do this?", and according
to x86 and s390 the answer is no, the scheduler will do it before calling
the arch hook.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Right now, there is no notifier that is called on a new cpu, before the new
cpu begins processing interrupts/softirqs.
Various kernel function would need that notification, e.g. kvm works around
by calling smp_call_function_single(), rcu polls cpu_online_map.
The patch adds a CPU_STARTING notification. It also adds a helper function
that sends the message to all cpu_chain handlers.
Tested on x86-64.
All other archs are untested. Especially on sparc, I'm not sure if I got
it right.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Existing Open Firmware practice is to report each processor core as a
separate node in the device tree. Report the value of the "reg" OF
property corresponding to a logical CPU's device node as the core_id
attribute in /sys/devices/system/cpu/cpu*/topology/core_id.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
