Currently the driver leds-pwm doesn't set max_brightness for the led device
although it's platform data proides a maximum brightness. Instead it stores its
own private driver struct. The max_brightness defaults to 255 for led device if
it has not been set.
As a result any leds-pwm device with a different maximum brightness will show
incorrect behavior, as it is posible to either set a longer then period duty
time or not be able to switch the led to full brightness.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This patch changes the default trigger from "ide-disk"
to "default-on". Users updating from kernels not having this
LED driver will prefer having the same LED behavior as they
used to.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
drivers/leds/leds-ss4200.c: In function 'ich7_lpc_probe':
drivers/leds/leds-ss4200.c:353: warning: 'return' with no value, in function returning non-void
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This driver provides an interface for controlling LEDs (or vibrators)
connected to PMICs for which there is a regulator framework driver.
This driver can be used, for instance, to control vibrator on all Motorola EZX
phones using the pcap-regulator driver services.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Use resource_size() for ioremap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Use resource_size() for ioremap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The LT3593 is a step-up DC/DC converter designed to drive up to ten
white LEDs in series. The current flow can be set with a control pin.
This driver controls any number of such devices connected on generic
GPIOs and exports the function as as platform_driver.
The gpio_led platform data struct definition is reused for this purpose.
Successfully tested on a PXA embedded board.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
pci_enable_result is defined using the __must_check macro but
leds-ss4200 is not checking the return value.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This makes the LEDs driver for ALIX2.C boards work with Coreboot by
looking up the port address in the MSR rather than hard-coding it.
The BIOS scan also needed some tweaks as the string in Coreboot differs
from the one in the legacy BIOS.
Successfully tested with both the legacy tinyBIOS as well as Coreboot
v3.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This code is based on a driver that came in the "Open-source
and GPL components" download here:
http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Server+Products&ProductLine=Intel%C2%AE+Storage+Systems&ProductProduct=Intel%C2%AE+Entry+Storage+System+SS4200-E&OSVersion=OS+Independent
It was in a file called nasgpio.c inside of a second zip file
called SS4200-E_Linux_SIO_Driver-v1.4.zip and is based on this
updated to use the LED subsystem with the ioctl and hardware
monitor support removed.
I don't have any need for brightness
control, and its code is *completely* separate from the on/off
controls implemented here. If anyone else wants it, I'd be
happy to look into adding it, but I don't care enough for now.
Except for the probe routines, I rewrote most of it. I also
Note that I don't have any hardware documentation except for
the original driver.
Thanks go to Arjan for his help in getting the original source
for this released and for chasing down some licensing issues.
Signed-off-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Makes use of skip_spaces() defined in lib/string.c for removing leading
spaces from strings all over the tree.
It decreases lib.a code size by 47 bytes and reuses the function tree-wide:
text data bss dec hex filename
64688 584 592 65864 10148 (TOTALS-BEFORE)
64641 584 592 65817 10119 (TOTALS-AFTER)
Also, while at it, if we see (*str && isspace(*str)), we can be sure to
remove the first condition (*str) as the second one (isspace(*str)) also
evaluates to 0 whenever *str == 0, making it redundant. In other words,
"a char equals zero is never a space".
Julia Lawall tried the semantic patch (http://coccinelle.lip6.fr) below,
and found occurrences of this pattern on 3 more files:
drivers/leds/led-class.c
drivers/leds/ledtrig-timer.c
drivers/video/output.c
@@
expression str;
@@
( // ignore skip_spaces cases
while (*str && isspace(*str)) { \(str++;\|++str;\) }
|
- *str &&
isspace(*str)
)
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6:
IXP4xx: GTWX5715 platform only has two PCI IRQ lines, not four.
IXP4xx: Introduce IXP4XX_GPIO_IRQ(n) macro and convert IXP4xx platform files.
IXP4xx: move Gemtek GTWX5715 platform macros to the platform code.
IXP4xx: Remove unused Motorola PrPMC1100 platform macros.
IXP4xx: move FSG platform macros to the platform code.
IXP4xx: move DSM G600 platform macros to the platform code.
IXP4xx: move NAS100D platform macros to the platform code.
IXP4xx: move NSLU2 platform macros to the platform code.
IXP4xx: move Coyote platform macros to the platform code.
IXP4xx: move AVILA platform macros to the platform code.
IXP4xx: move IXDP425 platform macros to the platform code.
IXP4xx: Extend PCI MMIO indirect address space to 1 GB.
IXP4xx: Fix compilation failure with CONFIG_IXP4XX_INDIRECT_PCI.
IXP4xx: Drop "__ixp4xx_" prefix from in/out/ioread/iowrite functions for clarity.
IXP4xx: Rename indirect MMIO primitives from __ixp4xx_* to __indirect_*.
IXP4xx: Ensure index is positive in irq_to_gpio() and npe_request().
ARM: fix insl() and outsl() endianness on IXP4xx architecture.
IXP4xx: Fix normally-disabled debugging text in drivers/net/arm/ixp4xx_eth.c.
IXP4xx: change the timer base frequency to 66.666000 MHz.
If there are leds present in the OF tree, but the GPIOs for (some) of
them are unavailable, led_data doesn't get populated with correct
devices. Then, on device unbinding, one can crash the kernel.
Workaround this by setting led->gpio to invalid value early.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which
implement device detection. The leds-pca9532 driver doesn't, so there
is no point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Riku Voipio <riku.voipio@iki.fi>
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The serio ports on i8042 are not completely isolated; while we provide
enough locking to ensure proper serialization when accessing control
and data registers AUX and KBD ports can still have an effect on each
other on PS/2 protocol level. The most prominent effect is that
issuing a command for the device connected to one port may cause
abort of the command currently executing by the device connected to
another port.
Since i8042 nor serio subsystem are not aware of the details of the
PS/2 protocol (length of the commands and their replies and so on) the
locking should be done on libps2 level by adding special handling when
we see that we are dealing with serio port on i8042.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A pointer to clevo_mail_led_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This is needed to get kde-powersave to work properly on some g4
powerbooks.
From: Olaf Hering <olh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Samuel R. C. Vale <srcvale@holoscopio.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The WM831x devices feature two software controlled status LEDs with
hardware assisted blinking.
The device can also autonomously control the LEDs based on a selection
of sources. This can be configured at boot time using either platform
data or the chip OTP. A sysfs file in the style of that for triggers
allowing the control source to be configured at run time. Triggers
can't be used here since they can't depend on the implementation details
of a specific LED type.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
If we change the inverted attribute to another value, the LED will not be
inverted until we change the GPIO state.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Samuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When setting the same GPIO number, multiple IRQ shared requests will be
done without freing the previous request. It will also try to free a
failed request or an already freed IRQ if 0 was written to the gpio file.
All these oops and leaks were fixed with the following solution: keep the
previous allocated GPIO (if any) still allocated in case the new request
fails. The alternative solution would desallocate the previous allocated
GPIO and set gpio as 0.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Samuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There already is a "default-on" trigger but there are problems with it.
For one, it's a inefficient way to do it and requires led trigger support
to be compiled in.
But the real reason is that is produces a glitch on the LED. The GPIO is
allocate with the LED *off*, then *later* when the trigger runs it is
turned back on. If the LED was already on via the GPIO's reset default or
action of the firmware, this produces a glitch where the LED goes from on
to off to on. While normally this is fast enough that it wouldn't be
noticeable to a human observer, there are still serious problems.
One is that there may be something else on the GPIO line, like a hardware
alarm or watchdog, that is fast enough to notice the glitch.
Another is that the kernel may panic before the LED is turned back on, thus
hanging with the LED in the wrong state. This is not just speculation, but
actually happened to me with an embedded system that has an LED which
should turn off when the kernel finishes booting, which was left in the
incorrect state due to a bug in the OF LED binding code.
We also let GPIO LEDs get their initial value from whatever the current
state of the GPIO line is. On some systems the LEDs are put into some
state by the firmware or hardware before Linux boots, and it is desired to
have them keep this state which is otherwise unknown to Linux.
This requires that the underlying GPIO driver support reading the value of
output GPIOs. Some drivers support this and some do not.
The platform device binding gains a field in the platform data
"default_state" that controls this. There are three constants defined to
select from on, off, or keeping the current state. The OpenFirmware
binding uses a property named "default-state" that can be set to "on",
"off", or "keep". The default if the property isn't present is off.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
LEDs driver for National Semiconductor LP3944 Funlight Chip
http://www.national.com/pf/LP/LP3944.html
This helper chip can drive up to 8 leds, with two programmable DIM
modes; it could even be used as a gpio expander but this driver assumes
it is used as a led controller.
The DIM modes are used to set _blink_ patterns for leds, the pattern is
specified supplying two parameters:
- period: from 0s to 1.6s
- duty cycle: percentage of the period the led is on, from 0 to 100
LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
leds, the camera flash light and the displays backlights.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Indent using tabs, not spaces.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Add initialisation of GPIO ports for compatibility with boards with Award
BIOS (e.g. ALIX.3D3).
Signed-off-by: Tobias Mueller <Tobias_Mueller@twam.info>
Reviewed-by: Constantin Baranov <const@mimas.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
WARNING: drivers/leds/leds-gpio.o(.text+0x153): Section mismatch in reference from the function gpio_led_probe() to the function .devinit.text:create_gpio_led()
The function gpio_led_probe() references the function __devinit
create_gpio_led(). This is often because gpio_led_probe lacks a __devinit
annotation or the annotation of create_gpio_led is wrong.
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Allow the user application to change the wave pattern and led current by
'wave_pattern' and 'rgb_current' sysfs files.
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Change the license to 'GPL v2'
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
LED_CORE_SUSPENDRESUME flag is not needed in the bd2802 driver, because
all works for suspend/resume is done in bd2802_suspend and bd2802_suspend
functions. And this patch allows bd2802 to be configured again when it
resumes from suspend.
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix build problems with leds-gpio:
CC drivers/leds/leds-gpio.o
drivers/leds/leds-gpio.c: In function 'create_gpio_led':
drivers/leds/leds-gpio.c:85: warning: 'return' with no value, in function returning non-void
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
LP5521 is a three channel led driver with support
for hardware accelerated patterns (currently used
via lp5521-only sysfs interface).
Currently, it's used on n810 device.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Sometimes it's awkward to make sure that the array in the
platform_data handed to the leds-gpio driver has only valid
data ... some leds may not be always available, and coping
with that currently requires patching or rebuilding the array.
This patch fixes that by making it be OK to pass an invalid
GPIO (such as "-EINVAL") ... such table entries are skipped.
[rpurdie@linux.intel.com: adjusted to apply against other led tree changes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tested-by: Diego Dompe <diego.dompe@ridgerun.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This fixes the expression in the driver to do the correct thing,
not that I think anyone would send SND_* without EV_SND.
Thanks to Roel Kluin <roel.kluin@gmail.com> for noticing.
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
A pointer to h1940leds_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This goto is unnecessary.
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
