UART driver slave idle issue has been taken care by driver using hwmod
framework.
So we can now ger rid off the L4 per clockdomain static dependency with
MPU which was used to wrok around UART wakeup and console sluggishnesh issue
on OMAP4 SOCs.
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
With commit bfd6d021 {ARM: OMAP3+: Implement timer workaround for errata
i103 and i767}, the sync and gptimer synchronization errata got fixed.
Hence the l4_wakeup static dependency with MPU can can be removed
now. Static dependency was one of the proposed workaround but from
power savings perspective, it isn't an ideal workaround.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move the secondary CPU wakeup prepare code under smp_prepare_cpus() where it
belongs. It was remainder of the pen release code which was borrowed from
ARM code initially.
While at it drop the un-necessary sev() and barrier which was under
prepare code.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The smp_wmb() here is out of placed and redundant. So remove it. It is
a left over of the pen_release cleanup mostly.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This was borrowed from ARM versatile code with pen_release mechanism but since
OMAP uses hardware register based synchronisation, pen_release stuff was
dropped. Unfortunately the cacheflush wasn't dropped along with it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This was added with intial port where OMAP PM support wasn't existing
and only simple WFI based hooks were used.
This should have been cleaned up while adding the PM support but some
how fall through cracks.
So remove the cache flush code which is no longer needed now.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
On OMAP platform, FIQ is reserved for secure environment only. If at all
the FIQ needs to be disabled, it involves going through security
API call. Hence the local_fiq_[enable/disable]() in the OMAP code is bogus.
On GP devices too, the fiq is disabled for non-secure software.
So just get rid of it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Choose the common scratch pad offsets, so that same offsets can work for
OMAP4 and OMAP5 devices. It simplifies code and also allows the re-use as
is on OMAP5 devices. Note that these offsets are used by low power
code for various power state management. They are not hardware register
offsets.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Here are some tiny fixes for the w1 drivers and the final removal patch
for getting rid of CONFIG_EXPERIMENTAL (all users of it are now gone
from your tree, this just drops the Kconfig item itself.)
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlFDUJkACgkQMUfUDdst+ylsBwCfTWMonhfZgKHTNxbJN7t734HA
yGUAn37hQcRma6schuOEAUCPOTlr/Xkj
=H3Oi
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg Kroah-Hartman:
"Here are some tiny fixes for the w1 drivers and the final removal
patch for getting rid of CONFIG_EXPERIMENTAL (all users of it are now
gone from your tree, this just drops the Kconfig item itself.)
All have been in the linux-next tree for a while"
* tag 'char-misc-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
final removal of CONFIG_EXPERIMENTAL
w1: fix oops when w1_search is called from netlink connector
w1-gpio: fix unused variable warning
w1-gpio: remove erroneous __exit and __exit_p()
ARM: w1-gpio: fix erroneous gpio requests
Pull DMA-mapping fix from Marek Szyprowski:
"An important fix for all ARM architectures which use ZONE_DMA.
Without it dma_alloc_* calls with GFP_ATOMIC flag might have allocated
buffers outsize DMA zone."
* 'fixes-for-3.9' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: DMA-mapping: add missing GFP_DMA flag for atomic buffer allocation
With this one we have:
- An ab8500 build failure fix.
- An ab8500 device tree parsing fix.
- A fix for twl4030_madc remove routine to work properly (when built-in).
- A fix for properly registering palmas interrupt handler.
- A fix for omap-usb init routine to actually write into the hostconfig
register.
- A couple of warning fixes for ab8500-gpadc and tps65912.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRQs2IAAoJEIqAPN1PVmxKN6sQAISiEmSjOiLRZ3b13qeKGiMX
3F3W5qXGYJQzhiVU/unPK9/2rTdfJ0Mqnuj88bLY+336pr89vi8g0k2VBWPfHlcv
jv2mJKWuNUM15D0d6uZ3t27jrXXBzNEvMjKKen2kYfm1+JcR+1N8pbJUZtOlgREJ
2Z23or/XP+ZCSbXcvzH1KvRFrcaBDedqgT4m0nat2dTfZ77MpKZEA58sutNBOUMa
YfoE2ncJBq5Ku4LBo6wGhsVptzilmpH3YBnSEgTh7tccyLrt4SnodNdT3vxmU4+1
C0r/oX9Idcij4/VAW/2bcEq1E12YUeKnPeVDAARXc+X/1Oyw+Mc6Cqd/rnvFomfe
9uTGMOmH1me1mSUgrzFNM1nnKXaZkWti56rLEe8tLsN7tkc+oWSJPIlWwjCmeWkC
R5SPgR5Jf6QeA4mW9qMxnBM3y8YlaV4awW6wwVYXGUDICZMG04qURSLo9NX3kDAA
AHsbE+IiSxdDqmZr8aejhaGd7PIVjfPhnM25TNlUZ5P5EWlApl4ha7QZ/BK2fx6k
DqaRujfB2uGcQAwqTprVpDI6lHUEneUKaa3zDpoxkP4vPVXDsRIiBo7HRfY8QXjg
vMWrYfLvAYBXHx69I5q2DghyFmofu/H0SXDdGlo33cQ5SfzeNGS7h0pPGrkNJyvN
7WJbiOdAYeQXVlBCy7sB
=XFgy
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes
Pull MFD fixes from Samuel Ortiz:
"This is the first batch of MFD fixes for 3.9.
With this one we have:
- An ab8500 build failure fix.
- An ab8500 device tree parsing fix.
- A fix for twl4030_madc remove routine to work properly (when
built-in).
- A fix for properly registering palmas interrupt handler.
- A fix for omap-usb init routine to actually write into the
hostconfig register.
- A couple of warning fixes for ab8500-gpadc and tps65912"
* tag 'mfd-fixes-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes:
mfd: twl4030-madc: Remove __exit_p annotation
mfd: ab8500: Kill "reg" property from binding
mfd: ab8500-gpadc: Complain if we fail to enable vtvout LDO
mfd: wm831x: Don't forward declare enum wm831x_auxadc
mfd: twl4030-audio: Fix argument type for twl4030_audio_disable_resource()
mfd: tps65912: Declare and use tps65912_irq_exit()
mfd: palmas: Provide irq flags through DT/platform data
mfd: Make AB8500_CORE select POWER_SUPPLY to fix build error
mfd: omap-usb-host: Actually update hostconfig
Atomic pool should always be allocated from DMA zone if such zone is
available in the system to avoid issues caused by limited dma mask of
any of the devices used for making an atomic allocation.
Reported-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Stable <stable@vger.kernel.org> [v3.6+]
* Compile warnings and errors (one on x86, two on ARM)
* WARNING in xen-pciback
* Use the acpi_processor_get_performance_info instead of the 'register' version
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRP33uAAoJEFjIrFwIi8fJfxMIAJxK7jI7NghJ87b8uk3IrkDl
VDsY5Re86XWE0HjsFDJXfWZCGumhpMb8hI1RJBavLDWQmk4THBqsKbx9rDgRZUJO
HepvhwD/RdK+nnjVmbAzJKuc7aOKQmeEW3Weysb32DW9C5Wg27LRrto/oVJIUsyj
4HrLcsZZqCiEYUZjGwrkrMC1yXx+2XvkX9mXq81hGj0xU4X1hMizwBAJvSE5lKca
r4LaCoZ0SuayHYHjEtxyjAcu39wnMdlCkdW9DUlqrjK7L3X29ifVvnb+aS951O5E
t57DCHY8WkI1BkaoHaAQqI7/Y1HpYbT8BALVmxXoIInI9lc8VLHZOs8/fVVDppQ=
=MxoB
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
- Compile warnings and errors (one on x86, two on ARM)
- WARNING in xen-pciback
- Use the acpi_processor_get_performance_info instead of the 'register'
version
* tag 'stable/for-linus-3.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/acpi: remove redundant acpi/acpi_drivers.h include
xen: arm: mandate EABI and use generic atomic operations.
acpi: Export the acpi_processor_get_performance_info
xen/pciback: Don't disable a PCI device that is already disabled.
Fix regression introduced by commit d2323cf773 ("onewire: w1-gpio: add
ext_pullup_enable pin in platform data") which added a gpio entry to the
platform data, but did not add the required initialisers to the board
files using it. Consequently, the driver would request gpio 0 at probe,
which could break other uses of the corresponding pin.
On AT91 requesting gpio 0 changes the pin muxing for PIOA0, which, for
instance, breaks SPI0 on at91sam9g20.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 887cbce0ad ("arch Kconfig: centralise ARCH_NO_VIRT_TO_BUS")
I introduced the config sybmol HAVE_VIRT_TO_BUS and selected that where
needed. I am not sure what I was thinking. Instead, just directly
select VIRT_TO_BUS where it is needed.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These bug fixes are for the largest part for mvebu/kirkwood, which
saw a few regressions after the clock infrastructure was enabled,
and for OMAP, which showed a few more preexisting bugs with
the new multiplatform support.
Other small fixes are for imx, mxs, tegra, spear and socfpga.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yq5v
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"These bug fixes are for the largest part for mvebu/kirkwood, which saw
a few regressions after the clock infrastructure was enabled, and for
OMAP, which showed a few more preexisting bugs with the new
multiplatform support.
Other small fixes are for imx, mxs, tegra, spear and socfpga"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: spear3xx: Use correct pl080 header file
Arm: socfpga: pl330: Add #dma-cells for generic dma binding support
ARM: multiplatform: Sort the max gpio numbers.
ARM: imx: fix typo "DEBUG_IMX50_IMX53_UART"
ARM: imx: pll1_sys should be an initial on clk
arm: mach-orion5x: fix typo in compatible string of a .dts file
arm: mvebu: fix address-cells in mpic DT node
arm: plat-orion: fix address decoding when > 4GB is used
arm: mvebu: Reduce reg-io-width with UARTs
ARM: Dove: add RTC device node
arm: mvebu: enable the USB ports on Armada 370 Reference Design board
ARM: dove: drop "select COMMON_CLK_DOVE"
rtc: rtc-mv: Add support for clk to avoid lockups
gpio: mvebu: Add clk support to prevent lockup
ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
ARM: mxs: cfa10049: Fix fb initialisation function
ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ"
ARM: OMAP: RX-51: add missing USB phy binding
clk: Tegra: Remove duplicate smp_twd clock
...
The definitions have move around recently, causing build errors
in spear3xx for all configurations:
spear3xx.c:47:5: error: 'PL080_BSIZE_16' undeclared here (not in a function)
spear3xx.c:47:23: error: 'PL080_CONTROL_SB_SIZE_SHIFT' undeclared here (not in a function)
spear3xx.c:48:22: error: 'PL080_CONTROL_DB_SIZE_SHIFT' undeclared here (not in a function)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alessandro Rubini <rubini@gnudd.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
The ab8500 device is a child of the prcmu device, which is a memory mapped
bus device, whose children are addressable using physical memory addresses,
not using mailboxes, so a mailbox number in the ab8500 node cannot be
parsed by DT. Nothing uses this number, since it was only introduced
as part of the failed attempt to clean up prcmu mailbox handling, and
we can simply remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds #dma-cells property to PL330 DMA controller nodes for
supporting generic dma dt bindings on SOCFPGA platform. #dma-channels
and #dma-requests are not required now but added in advance.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The first four patches:
89c58c1 rtc: rtc-mv: Add support for clk to avoid lockups
de88747 gpio: mvebu: Add clk support to prevent lockup
7bf5b40 ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
93fff4c ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
are Cc'd to stable since they were held over from the previous merge window.
The rest are a small collection of fixes and a couple of devicetree conversion
catchups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJROmXfAAoJEAi3KVZQDZAeahAIAIWybkKuD/lKLRPU3FmS59gM
gdcPxQcjFnldRRBQFXRfSQ4acFNEWZwDgHXs0gpKsUCoZ2w/tCbjba0sNb2vWsmc
H4Nh8MU3CqHIuGDFSmsbDHX0BNrp6JvZLxiY7vtswTDqZt1K/UKb7obnnbAo8ygu
OtbGItfYNTjMJ0B1Ar2eYCoA4V29SFzXB+ymWEHl4u9Vmwasr0uervjHhyq+3tU1
pCNPWc98N9r0VqniVbbTqVuwlwoc3IZmbiv1T9EGMw2PDbtcIJLwY7oxlSb0kW3e
QIookCxlItX1A360TmGI4xKnSRR42ZinNmn2AuLetW8ydnRNDwkyrRJZ2VsbQLE=
=mme/
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.9' of git://git.infradead.org/users/jcooper/linux into fixes
mvebu fixes for v3.9 from Jason Cooper <jason@lakedaemon.net>:
The first four patches:
89c58c1 rtc: rtc-mv: Add support for clk to avoid lockups
de88747 gpio: mvebu: Add clk support to prevent lockup
7bf5b40 ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
93fff4c ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
are Cc'd to stable since they were held over from the previous merge window.
The rest are a small collection of fixes and a couple of devicetree conversion
catchups.
* tag 'mvebu_fixes_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
arm: mach-orion5x: fix typo in compatible string of a .dts file
arm: mvebu: fix address-cells in mpic DT node
arm: plat-orion: fix address decoding when > 4GB is used
arm: mvebu: Reduce reg-io-width with UARTs
ARM: Dove: add RTC device node
arm: mvebu: enable the USB ports on Armada 370 Reference Design board
ARM: dove: drop "select COMMON_CLK_DOVE"
rtc: rtc-mv: Add support for clk to avoid lockups
gpio: mvebu: Add clk support to prevent lockup
ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix pll1_sys clk initial status
- Fix a typo in imx DEBUG_LL Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRPeaEAAoJEFBXWFqHsHzOIFgH/RNeNudfIZ5yBaP0xWu1h9lm
gxvXRJshzQOYovT0qDL6w7/ia57b4b8zGQlbR8x86U7EjqFdgrAhYeI12dVwDEAf
165MM1h0f36w5wAQqjGE1isTVUpl29zPDLSIg87t1AnBARtrhwwhKKjIF9lT+Sc9
ar94MphjgPwIgDnflVqQl0IGW4DI+Zc6VZLzpBvcmN33J/K3owhAtr4F+pLSXsnR
5NH2ml37IUgDqQpo2OFQk4mysPCv797Hl6SHXbFLIaDiYi91jhJ7YzDrnI8v7evH
tTpWDrkR6o/uG9+77mhhtp8LR0BVBLPgBfy8FXNdW13LXn0qbKArkxe9iILmlSw=
=8nT7
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The 2nd take of imx fixes for 3.9:
- Fix pll1_sys clk initial status
- Fix a typo in imx DEBUG_LL Kconfig
* tag 'imx-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: fix typo "DEBUG_IMX50_IMX53_UART"
ARM: imx: pll1_sys should be an initial on clk
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix an error caused by incorrect conflict resolution when
applying the patch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRPeg/AAoJEFBXWFqHsHzOmkEH/3mjPeA/bmly/LuUWd2BdS8W
VbKzKKBJpXa34wFnj1aH2ydViPs4PWHHIxB2Z3u+epu+43w+DdDtjrM1XdX8lAYN
5z90l5ZYXoeq2H3xaqCwCzHzp0FwxbrxmXN9Kr97pOxefAJMmpO8/yrMgtO2ADAd
f3Z8wQCM7J4QRjCAHd+8sPsDfnkkGtMdlLsD3I2IRbBOU15LdaFVd1zXGbi/M/wo
rW/3aZ9YbJSuOdwQ8ucGnNp+ZXiUUCPy9DDplt7yfpQkKhML/fqz3t6bznaZs/YD
UWtqiP/wfVTlz9yhRCLOPoGU/ix8Rmk1ltZtTvqNY+b9JLsnFiwwK8Ngo4C5IcE=
=TYXe
-----END PGP SIGNATURE-----
Merge tag 'mxs-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The 2nd mxs fixes for 3.9:
- Fix an error caused by incorrect conflict resolution when
applying the patch
* tag 'mxs-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: cfa10049: Fix fb initialisation function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When building a multiplatform kernel, we could end up with a smaller
number of GPIOs than the one required by the platform the kernel was
running on.
Sort the max GPIO number by descending order so that we always take the
highest number required.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rob Herring has observed that c81611c4e9 "xen: event channel arrays are
xen_ulong_t and not unsigned long" introduced a compile failure when building
without CONFIG_AEABI:
/tmp/ccJaIZOW.s: Assembler messages:
/tmp/ccJaIZOW.s:831: Error: even register required -- `ldrexd r5,r6,[r4]'
Will Deacon pointed out that this is because OABI does not require even base
registers for 64-bit values. We can avoid this by simply using the existing
atomic64_xchg operation and the same containerof trick as used by the cmpxchg
macros. However since this code is used on memory which is shared with the
hypervisor we require proper atomic instructions and cannot use the generic
atomic64 callbacks (which are based on spinlocks), therefore add a dependency
on !GENERIC_ATOMIC64. Since we already depend on !CPU_V6 there isn't much
downside to this.
While thinking about this we also observed that OABI has different struct
alignment requirements to EABI, which is a problem for hypercall argument
structs which are shared with the hypervisor and which must be in EABI layout.
Since I don't expect people to want to run OABI kernels on Xen depend on
CONFIG_AEABI explicitly too (although it also happens to be enforced by the
!GENERIC_ATOMIC64 requirement too).
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <robherring2@gmail.com>
Acked-by: Stefano Stabellini <Stefano.Stabellini@eu.citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Commit f8c95fe (ARM: imx: support DEBUG_LL uart port selection for all
i.MX SoCs) had a typo that DEBUG_IMX50_IMX53_UART should be
DEBUG_IMX53_UART.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We always boot from PLL1, so let's have pll1_sys in the clks_init_on
list to have clk prepare/enable use count match the hardware status,
so that drivers managing pll1_sys like cpufreq can get the use count
right from the start.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The orion5x-lacie-ethernet-disk-mini-v2.dts file was using
"marvell-orion5x-88f5182" as a compatible string, while it should have
been "marvell,orion5x-88f5182".
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There is no need to have a #address-cells property in the MPIC Device
Tree node, and more than that, having it confuses the of_irq_map_raw()
logic, which will be used by the Marvell PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
During the system initialization, the orion_setup_cpu_mbus_target()
function reads the SDRAM address decoding registers to find out how
many chip-selects of SDRAM have been enabled, and builds a small array
with one entry per chip-select. This array is then used by device
drivers (XOR, Ethernet, etc.) to configure their own address decoding
windows to the SDRAM.
However, devices can only access the first 32 bits of the physical
memory. Even though LPAE is not supported for now, some Marvell boards
are now showing up with 8 GB of RAM, configured using two SDRAM
address decoding windows: the first covering the first 4 GB, the
second covering the last 4 GB. The array built by
orion_setup_cpu_mbus_target() has therefore two entries, and device
drivers try to set up two address decoding windows to the
SDRAM. However, in the device registers for the address decoding, the
base address is only 32 bits, so those two windows overlap each other,
and the devices do not work at all.
This patch makes sure that the array built by
orion_setup_cpu_mbus_target() only contains the SDRAM decoding windows
that correspond to the first 4 GB of the memory. To do that, it
ignores the SDRAM decoding windows for which the 4 low-order bits are
not zero (the 4 low-order bits of the base register are used to store
bits 32:35 of the base address, so they actually indicate whether the
base address is above 4 GB).
This patch allows the newly introduced armada-xp-gp board to properly
operate when it is mounted with more than 4 GB of RAM. Without that,
all devices doing DMA (for example XOR and Ethernet) do not work at
all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Setting the reg-io-width to 1 byte represents more accurate
description of the HW.
This will fix an issue where UART driver causes kernel
panic during bootup. Gregory CLEMENT traced the issue to
autoconfig() in 8250.c, where the existence of FIFO is
checked from UART_IIR register. The register is now read as
32-bit value as the reg-io-width is set to 4-bytes. The
retuned value seems to contain bogus data for bits 31:8,
causing the issue.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The commit:
48be9ac ARM: Dove: split legacy and DT setup
removed the RTC initialization. This patch re-enables the RTC
via the DT.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch modifies the Armada 370 Reference Design DTS file to enable
support for the two USB ports found on this board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit 5b03df9ace ("ARM: dove: switch to
DT clock providers") added "select COMMON_CLK_DOVE" to Marvell Dove's
Kconfig entry. But there's no Kconfig symbol COMMON_CLK_DOVE, which
makes this select statement a nop. It's probably a leftover of some
experimental code that never hit mainline. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ethernet controller used on kirkwood looses its MAC address
register contents when the corresponding clock is gated. As soon as
mv643xx_eth is built as module, the clock gets gated and when loading
the module, the MAC address is gone.
Proper DT support for the mv643xx_eth driver is expected soon, so we add
a workaround to always enable ge0/ge1 clocks on kirkwood. This workaround
is also already used on non-DT kirkwood kernels.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When DT support for kirkwood was first introduced, there was no clock
infrastructure. As a result, we had to manually pass the
clock-frequency to the driver from the device node.
Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.
The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.
Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.
Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Recent GCC versions (e.g. GCC-4.7.2) perform optimizations based on
assumptions about the implementation of memset and similar functions.
The current ARM optimized memset code does not return the value of
its first argument, as is usually expected from standard implementations.
For instance in the following function:
void debug_mutex_lock_common(struct mutex *lock, struct mutex_waiter *waiter)
{
memset(waiter, MUTEX_DEBUG_INIT, sizeof(*waiter));
waiter->magic = waiter;
INIT_LIST_HEAD(&waiter->list);
}
compiled as:
800554d0 <debug_mutex_lock_common>:
800554d0: e92d4008 push {r3, lr}
800554d4: e1a00001 mov r0, r1
800554d8: e3a02010 mov r2, #16 ; 0x10
800554dc: e3a01011 mov r1, #17 ; 0x11
800554e0: eb04426e bl 80165ea0 <memset>
800554e4: e1a03000 mov r3, r0
800554e8: e583000c str r0, [r3, #12]
800554ec: e5830000 str r0, [r3]
800554f0: e5830004 str r0, [r3, #4]
800554f4: e8bd8008 pop {r3, pc}
GCC assumes memset returns the value of pointer 'waiter' in register r0; causing
register/memory corruptions.
This patch fixes the return value of the assembly version of memset.
It adds a 'mov' instruction and merges an additional load+store into
existing load/store instructions.
For ease of review, here is a breakdown of the patch into 4 simple steps:
Step 1
======
Perform the following substitutions:
ip -> r8, then
r0 -> ip,
and insert 'mov ip, r0' as the first statement of the function.
At this point, we have a memset() implementation returning the proper result,
but corrupting r8 on some paths (the ones that were using ip).
Step 2
======
Make sure r8 is saved and restored when (! CALGN(1)+0) == 1:
save r8:
- str lr, [sp, #-4]!
+ stmfd sp!, {r8, lr}
and restore r8 on both exit paths:
- ldmeqfd sp!, {pc} @ Now <64 bytes to go.
+ ldmeqfd sp!, {r8, pc} @ Now <64 bytes to go.
(...)
tst r2, #16
stmneia ip!, {r1, r3, r8, lr}
- ldr lr, [sp], #4
+ ldmfd sp!, {r8, lr}
Step 3
======
Make sure r8 is saved and restored when (! CALGN(1)+0) == 0:
save r8:
- stmfd sp!, {r4-r7, lr}
+ stmfd sp!, {r4-r8, lr}
and restore r8 on both exit paths:
bgt 3b
- ldmeqfd sp!, {r4-r7, pc}
+ ldmeqfd sp!, {r4-r8, pc}
(...)
tst r2, #16
stmneia ip!, {r4-r7}
- ldmfd sp!, {r4-r7, lr}
+ ldmfd sp!, {r4-r8, lr}
Step 4
======
Rewrite register list "r4-r7, r8" as "r4-r8".
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 1fe42740 ("ARM: dts: mxs: Add the LCD to the 10049 board") seem
to have been applied with some fuzzyness, and the framebuffer
initialisation code for the CFA-10049 ended up in the CFA-10037
initialisation function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
WARNING: vmlinux.o(.text+0xfb80): Section mismatch in reference
from the function armpmu_register() to the function
.init.text:armpmu_init()
The function armpmu_register() references
the function __init armpmu_init().
This is often because armpmu_register lacks a __init
annotation or the annotation of armpmu_init is wrong.
Just drop the __init marking on armpmu_init() because
armpmu_register() no longer has an __init marking.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Before jumping to (position independent) C-code from the decompressor's
assembler world we set-up the C environment. This setup currently does not
set r9, which for arm-none-uclinux-uclibceabi toolchains is by default
expected to be the PIC offset base register (IE should point to the
beginning of the GOT).
Currently, therefore, in order to build working kernels that use the
decompressor it is necessary to use an arm-linux-gnueabi toolchain, or
similar. uClinux toolchains cause a prefetch abort to occur at the beginning
of the decompress_kernel function.
This patch allows uClinux toolchains to build bootable zImages by forcing
the -mno-single-pic-base option, which ensures that the location of the GOT
is re-derived each time it is required, and r9 becomes free for use as a
general purpose register.
This has a small (4% in instruction terms) advantage over the alternative of
setting r9 to point to the GOT before calling into the C-world.
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 51482be9 (ARM: OMAP: USB: Add phy binding information) forgot to
add phy binding for RX-51, and as a result USB does not work anymore on
3.9-rc1. Add the missing binding.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- A few sparse warning fixes
- Fix usb function regression caused by usb Kconfig option changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRNELIAAoJEFBXWFqHsHzOP/QH/jjE9MrvckPwb8h1I7R8a7yc
td3N5rikKiy2XN4snjIrPFaKi9JQ//I1oLvhsXNSD1uqWqqtRLg6lxzIdiheUJEd
NsAFLKTPMaJHJ/s3y0mLNRgyuBcyvDrF6jYJ8ncdGDCMAXBKifkTmrqqai2d0dZz
DiIiEW46PVhsQkoxdnLKw7xGScmXJpyqwshbi+zhAB17yE1FBLCCsZGD1jVr0v/y
Q6pnCjiJ8es9SAvmCvZ8cY1XxOxUMsCr2VhIy/QPF5HyuZPcRaV1nVGljfzo13J3
sPvBfmUZaY9ezqOVCUuYatQ3bAQ5f55KsLuGz+IHwMLHllXAML0Fw69/oDR86qs=
=JOus
-----END PGP SIGNATURE-----
Merge tag 'mxs-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
The mxs fixes for 3.9:
- A few sparse warning fixes
- Fix usb function regression caused by usb Kconfig option changes
* tag 'mxs-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: ocotp: Fix sparse warning
ARM: mxs: icoll: Fix sparse warning
ARM: mxs: mm: Fix sparse warning
ARM: mxs_defconfig: Make USB host functional again
Signed-off-by: Olof Johansson <olof@lixom.net>
- move early resume code out of .data section to fix allyesconfig
failure since c08e20d (arm: Add v7_invalidate_l1 to cache-v7.S)
gets merged
- Fix incorrect DISP1_DAT_21 number in imx53-mba53 disp1-grp1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRND3rAAoJEFBXWFqHsHzOL2cH/je/02JztrorpD2k76mQLjo4
2hjfUwpYNvwEpwBCXo5NnDv5I4XrkJdHs7O2CHmigQOpDYSvq9qx3VcPQ0BX8cWU
3Qqb9tiglNsvD2NuxUYmG2CHFpGLp+lK3unkA/ZDXM2apjbacL1/wTgU81uthDwY
SLBBS7hSlBvuPdxoeIBeuOOBYnhbdaZCutgFVTF8rRT6RHmYjekga6OqF32Vp/og
Gxw50cj+smdW6wr1Na0zQJfMHTkm5hJ9s9iYHAbYNZplpl8VZJQAaCWgZhihZJYI
XULUCR0s8DLLUgj4IUgJS3Kc35G/2M1ovhxyw3hqDzOt+Miy8m4eYh21BL2iS8w=
=V76T
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
The imx fixes for 3.9:
- move early resume code out of .data section to fix allyesconfig
failure since c08e20d (arm: Add v7_invalidate_l1 to cache-v7.S)
gets merged
- Fix incorrect DISP1_DAT_21 number in imx53-mba53 disp1-grp1
* tag 'imx-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx53-mba53: fix fsl,pins for disp1-grp1
ARM: mach-imx: move early resume code out of the .data section
Signed-off-by: Olof Johansson <olof@lixom.net>
As DT support for clocks and smp_twd is enabled, add clock entry
for smp_twd clock to DT.
This fixes the following error while booting the kernel:
smp_twd: clock not found -2
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: include kernel log spew that this fixes]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
commit 5f300acd8a
(ARM: 7152/1: distclean: Remove generated .dtb files)
ensured that dtbs were cleaned up when they were in
arch/arm/boot.
However, with the following commit:
commit 499cd82986
(ARM: dt: change .dtb build rules to build in dts directory)
make clean now leaves dtbs in arch/arm/boot/dts/
untouched. Include dts directory so that clean-files rule
from arch/arm/boot/dts/Makefile is invoked when make
clean is done.
Cc: Dirk Behme <dirk.behme@de.bosch.com>
CC: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
BCM2835-ARM-Peripherals.pdf states that the I2C module's input clock is
nominally 150MHz, and that value is currently reflected in bcm2835.dtsi.
However, practical measurements show that the rate is actually 250MHz,
and this agrees with various downstream kernels.
Switch the I2C clock's frequency to 250MHz so that the generated bus
clock rate is accurate.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit bbd707ac {ARM: omap2: use machine specific hook for late init}
accidentally added two declarations for omap4430_init_late().
Remove the duplicate declaration.
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
