In OMAP35X TRM Rev 2010-05 Figure 7-18 "DPLL With EMI Reduction
Feature", it is shown that the internal frequency is calculated by
CLK_IN/(N+1). However, the value passed to _dpll_test_fint() is
already "N+1" since Linux is using the values to divide by. In the
technical reference manual, "N" is referring to the divider's register
value (0-127).
During power management testing, it was observed that programming the
wrong jitter correction value can cause the system to become unstable
and eventually crash.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
[paul@pwsan.com: added second paragraph to commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the dr_intercept function a new cpu-feature called
decode-assists is implemented and used when available. This
code-path does not advance the guest-rip causing the guest
to dead-loop over mov-dr instructions. This is fixed by this
patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6745/1: kprobes insn decoding fix
ARM: tlb: move noMMU tlb_flush() to asm/tlb.h
ARM: tlb: delay page freeing for SMP and ARMv7 CPUs
ARM: Keep exit text/data around for SMP_ON_UP
ARM: Ensure predictable endian state on signal handler entry
ARM: 6740/1: Place correctly notes section in the linker script
ARM: 6700/1: SPEAr: Correct SOC config base address for spear320
ARM: 6722/1: SPEAr: sp810: switch to slow mode before reset
ARM: 6712/1: SPEAr: replace readl(), writel() with relaxed versions in uncompress.h
ARM: 6720/1: SPEAr: Append UL to VMALLOC_END
ARM: 6676/1: Correct the cpu_architecture() function for ARMv7
ARM: 6739/1: update .gitignore for boot/compressed
ARM: 6743/1: errata: interrupted ICALLUIS may prevent completion of broadcasted operation
ARM: 6742/1: pmu: avoid setting IRQ affinity on UP systems
ARM: 6741/1: errata: pl310 cache sync operation may be faulty
Marcin Slusarz says:
> In arch/arm/kernel/kprobes-decode.c there's a function
> arm_kprobe_decode_insn which does:
>
> } else if ((insn & 0x0e000000) == 0x0c400000) {
> ...
>
> This is always false, so code below is dead.
> I found this bug by coccinelle (http://coccinelle.lip6.fr/).
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to noMMU to put tlb_flush() in asm/tlbflush.h - it's
part of the tlb shootdown interface. Move it to asm/tlb.h instead, as
per x86.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to delay freeing any mapped page on SMP and ARMv7 systems to
ensure that the data is not accessed by other CPUs, or is used for
speculative prefetch with ARMv7. This includes not only mapped pages
but also pages used for the page tables themselves.
This avoids races with the MMU/other CPUs accessing pages after they've
been freed but before we've invalidated the TLB.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When SMP_ON_UP is used and the spinlocks are inlined, we end up with
inline spinlocks in the exit code, with references from the SMP
alternatives section to the exit sections. This causes link time
errors. Avoid this by placing the exit sections in the init-discarded
region.
Cc: <stable@kernel.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure a predictable endian state when entering signal handlers. This
avoids programs which use SETEND to momentarily switch their endian
state from having their signal handlers entered with an unpredictable
endian state.
Cc: <stable@kernel.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 18991197b4 added --build-id
linker option when toolchain supports it. ARM one does, but for some
reason places the section at 0 when linker script doesn't mention it
explicitly.
The 1e621a8e37 worked around the problem
removing this section from binary image with explicit objcopy options,
but it still exists in vmlinux, confusing tools like debuggers and perf.
This problem was discussed here:
http://lists.infradead.org/pipermail/linux-arm-kernel/2010-May/015994.htmlhttp://lists.infradead.org/pipermail/linux-arm-kernel/2010-May/015994.html
but the proposed changes to the linker script were substantial.
This patch simply places NOTES (36 bytes long, at least when compiled
with CodeSourcery toolchain) between data and bss, which seem to be
the right place (and suggested by the sample linker script in
include/asm-generic/vmlinux.lds.h).
It is enough to place it correctly in vmlinux (so debuggers are happy):
Section Headers:
[11] .data PROGBITS c07ce000 7ce000 020fc0 00 WA 0 0 32
[12] .notes NOTE c07eefc0 7eefc0 000024 00 AX 0 0 4
[13] .bss NOBITS c07ef000 7eefe4 01e628 00 WA 0 0 32
Program Headers:
LOAD 0x008000 0xc0008000 0xc0008000 0x7e6fe4 0x805628 RWE 0x8000
NOTE 0x7eefc0 0xc07eefc0 0xc07eefc0 0x00024 0x00024 R E 0x4
Section to Segment mapping:
Segment Sections...
00 <...> .data .notes .bss
01 .notes
and to get it exposed as /sys/kernel/notes used by perf tools.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SPEAR320_SOC_CONFIG_BASE was wrong, causing the wrong registers to be
accessed.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In sysctl_soft_reset(), switch to slow mode before resetting the system
via the system controller. This is required.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
readl() and writel() calls the outer cache maintainance operations
which are not available during Linux uncompression. This patch replaces
readl() and writel() with readl_relaxed() and writel_relaxed() to avoid
the link time errors.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes following warning:
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
by appending UL to VMALLOC_END's Number.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VersaLogic Menlow based boards hang on reboot unless reboot=bios
is used. Add quirk to reboot through the BIOS.
Tested on at least four boards.
Signed-off-by: Kushal Koolwal <kushalkoolwal@gmail.com>
LKML-Reference: <1298152563-21594-1-git-send-email-kushalkoolwal@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If ID_MMFR0[3:0] >= 3, the architecture version is ARMv7. The code was
currently only testing for ID_MMFR0[3:0] == 3.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On versions of the Cortex-A9 prior to r3p0, an interrupted ICIALLUIS
operation may prevent the completion of a following broadcasted
operation if the second operation is received by a CPU before the
ICIALLUIS has completed, potentially leading to corrupted entries in
the cache or TLB.
This workaround sets a bit in the diagnostic register of the Cortex-A9,
causing CP15 maintenance operations to be uninterruptible.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we can execute a CONFIG_SMP kernel on a uniprocessor system,
extra care has to be taken in the PMU IRQ affinity setting code to
ensure that we don't always fail to initialise.
This patch changes the CPU PMU initialisation code so that when we
only have a single IRQ, whose affinity can not be changed at the
controller, we report success (0) rather than -EINVAL.
Reported-by: Avik Sil <avik.sil@linaro.org>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The effect of cache sync operation is to drain the store buffer and
wait for all internal buffers to be empty. In normal conditions, store
buffer is able to merge the normal memory writes within its 32-byte
data buffers. Due to this erratum present in r3p0, the effect of cache
sync operation on the store buffer still remains when the operation
completes. This means that the store buffer is always asked to drain
and this prevents it from merging any further writes.
This can severely affect performance on the write traffic esp. on
Normal memory NC one.
The proposed workaround is to replace the normal offset of cache sync
operation(0x730) by another offset targeting an unmapped PL310
register 0x740.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Fn keymap support to allow for internal processing of Fn keys.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since commit 1130e5b3ff regulators are exported to debugfs. The names
of the regulators that contains slash ('/') causes an ops during kernel
boot. This patch fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Max8998 PMIC driver's platform data has been changed once again in
commit 735a3d9efd. This patch fixes build break caused by that commit.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
s3c24xx_ts_set_platdata is annotated __init and not used by any module,
thus don't export it.
This patch fixes below warning:
WARNING: arch/arm/plat-samsung/built-in.o(__ksymtab+0x90): Section mismatch
in reference from the variable __ksymtab_s3c24xx_ts_set_platdata to the
function .init.text:s3c24xx_ts_set_platdata()
The symbol s3c24xx_ts_set_platdata is exported and annotated __init
Fix this by removing the __init annotation of s3c24xx_ts_set_platdata
or drop the export.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Just as we had to disable auto-demotion for NHM/WSM,
we need to do the same for Atom (Lincroft version).
In particular, auto-demotion will prevent Lincroft
from entering the S0i3 idle power saving state.
https://bugzilla.kernel.org/show_bug.cgi?id=25252
Signed-off-by: Len Brown <len.brown@intel.com>
Hardware C-state auto-demotion is a mechanism where the HW overrides
the OS C-state request, instead demoting to a shallower state,
which is less expensive, but saves less power.
Modern Linux should generally get exactly the states it requests.
In particular, when a CPU is taken off-line, it must not be demoted, else
it can prevent the entire package from reaching deep C-states.
https://bugzilla.kernel.org/show_bug.cgi?id=25252
Signed-off-by: Len Brown <len.brown@intel.com>
NET_SKB_PAD has been increased from 32 to 64 and later to
max(32, L1_CACHE_BYTES). This led to a 25% throughput decrease for
streaming workloads accompanied by a 37% CPU cost increase on s390.
Define a architecture specific NET_SKB_PAD with the old value of 32.
Signed-off-by: Horst Hartmann <horsth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use inline assemblies for atomic_read/set(). This way there shouldn't
be any questions or subtle volatile semantics left.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The 'output' variable is passed from decompress_kernel to
check_ipl_parmblock before it is initialized. That disables the
safe guard against the overwrite of the ipl parameter block.
Fix this by passing the correct value to check_ipl_parmblock.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let's make atomic_read() and atomic_set() behave like on all/most other
architectures. Generated code is identical with gcc 4.5.2.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For S5P platforms, the end address in memory resource information for UART
devices is one byte more than the intended value. Fix this by reducing the
end address by one byte.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Several people have reported spurious unknown NMI
messages on some P4 CPUs.
This patch fixes it by checking for an overflow (negative
counter values) directly, instead of relying on the
P4_CCCR_OVF bit.
Reported-by: George Spelvin <linux@horizon.com>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Don Zickus <dzickus@redhat.com>
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <AANLkTinfuTfCck_FfaOHrDqQZZehtRzkBum4SpFoO=KJ@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: set flow handler for secondary interrupt controller of 5249
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
m68knommu: fix dereference of port.tty
m68knommu: add missing linker __modver section
m68knommu: fix mis-named variable int set_irq_chip loop
m68knommu: add optimize memmove() function
m68k: remove arch specific non-optimized memcmp()
m68knommu: fix use of un-defined _TIF_WORK_MASK
m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
m68knommu: fix m548x_wdt.c compilation after headers renaming
m68knommu: Remove dependencies on nonexistent M68KNOMMU
The secondary interrupt controller of the ColdFire 5249 code is not
setting the edge triggered flow handler. Set it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Compiling for 68360 targets gives:
CC arch/m68knommu/platform/68360/ints.o
arch/m68knommu/platform/68360/ints.c: In function ‘init_IRQ’:
arch/m68knommu/platform/68360/ints.c:135:16: error: ‘irq’ undeclared (first use in this function)
arch/m68knommu/platform/68360/ints.c:135:16: note: each undeclared identifier is reported only once for each function it appears in
Fix variable name used.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Add an m68k/coldfire optimized memmove() function for the m68knommu arch.
This is the same function as used by m68k. Simple speed tests show this
is faster once buffers are larger than 4 bytes, and significantly faster
on much larger buffers (4 times faster above about 100 bytes).
This also goes part of the way to fixing a regression caused by commit
ea61bc461d ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memmove() fucntion
defined, since there was none in the m68knommu/lib functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The m68k arch implements its own memcmp() function. It is not optimized
in any way (it is the most strait forward coding of memcmp you can get).
Remove it and use the kernels standard memcmp() implementation.
This also goes part of the way to fixing a regression caused by commit
ea61bc461d ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memcmp() function
defined, since there is none in the m68knommu/lib functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Doing NMI startup as an early initcall doesn't work because we need
to have SMP started up by then.
So we'd only NMI startup one cpu, which causes perf PMU grab to
BUG because the nmi_active count isn't what it's supposed to be.
This also points out that we don't have proper CPU up/down notifiers
for the NMI code which will need to be fixed at some point.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix text_poke_smp_batch() deadlock
perf tools: Fix thread_map event synthesizing in top and record
watchdog, nmi: Lower the severity of error messages
ARM: oprofile: Fix backtraces in timer mode
oprofile: Fix usage of CONFIG_HW_PERF_EVENTS for oprofile_perf_init and friends
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, dmi, debug: Log board name (when present) in dmesg/oops output
x86, ioapic: Don't warn about non-existing IOAPICs if we have none
x86: Fix mwait_usable section mismatch
x86: Readd missing irq_to_desc() in fixup_irq()
x86: Fix section mismatch in LAPIC initialization
task_show_regs used to be a debugging aid in the early bringup days
of Linux on s390. /proc/<pid>/status is a world readable file, it
is not a good idea to show the registers of a process. The only
correct fix is to remove task_show_regs.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current makerel had issue which couldn't boot sometimes.
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current ap4evb had issue which couldn't boot sometimes.
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes the:
- __nosave_begin
- __nosave_end
symbols from 'void' to 'long' as required by the latest
Gcc (4.5.2) which raises the compilation error:
cc1: warnings being treated as errors
arch/sh/kernel/swsusp.c: In function 'pfn_is_nosave':
arch/sh/kernel/swsusp.c:24:28: error: taking address of expression of type 'void'
arch/sh/kernel/swsusp.c:25:26: error: taking address of expression of type 'void'
arch/sh/kernel/swsusp.c:25:26: error: taking address of expression of type 'void'
arch/sh/kernel/swsusp.c:25:26: error: taking address of expression of type 'void'
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This resolves a problem seen when using the Android dynamic linker.
Sometimes the dynamic linker would seg-fault at start up and this
was eventually traced to the handling of a COW fault for a page which
was being modified by the linker. If there was no cache aliasing between
the kernel and the user page, the page was not flushed, leaving the
newly copied data in the D-cache. However when executing instructions
from that page, the I-cache is filled directly from external memory,
rather than the D-cache, and causing garbage to be executed.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A strange variation was seen in the BogoMIPS figure for the ST40-300.
This was eventually tracked down to sensitivity to the alignment of
the loop. So add an align directive to ensure this doesn't occur.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The "Type 2" SMBIOS record that contains Board Name is not
strictly required and may be absent in the SMBIOS on some
platforms.
( Please note that Type 2 is not listed in Table 3 in Sec 6.2
("Required Structures and Data") of the SMBIOS v2.7
Specification. )
Use the Manufacturer Name (aka System Vendor) name.
Print Board Name only when it is present.
Before the fix:
(i) dmesg output: DMI: /ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2170, comm: bash Not tainted 2.6.38-rc4+ #3 /ProLiant DL380 G6
After the fix:
(i) dmesg output: DMI: HP ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2278, comm: bash Not tainted 2.6.38-rc4+ #4 HP ProLiant DL380 G6
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: <stable@kernel.org> # .3x - good for debugging, please apply as far back as it applies cleanly
LKML-Reference: <20110214224423.2182.13929.sendpatchset@nchumbalkar.americas.hpqcorp.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
mp_find_ioapic() prints errors like:
ERROR: Unable to locate IOAPIC for GSI 13
if it can't find the IOAPIC that manages that specific GSI. I
see errors like that at every boot of a laptop that apparently
doesn't have any IOAPICs.
But if there are no IOAPICs it doesn't seem to be an error that
none can be found. A solution that gets rid of this message is
to directly return if nr_ioapics (still) is zero. (But keep
returning -1 in that case, so nothing breaks from this change.)
The call chain that generates this error is:
pnpacpi_allocated_resource()
case ACPI_RESOURCE_TYPE_IRQ:
pnpacpi_parse_allocated_irqresource()
acpi_get_override_irq()
mp_find_ioapic()
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6657/1: hw_breakpoint: fix ptrace breakpoint advertising on unsupported arch
ARM: 6656/1: hw_breakpoint: avoid UNPREDICTABLE behaviour when reading DBGDSCR
ARM: 6658/1: collie: do actually pass locomo_info to locomo driver
ARM: 6659/1: Thumb-2: Make CONFIG_OABI_COMPAT depend on !CONFIG_THUMB2_KERNEL
ARM: 6654/1: perf/oprofile: fix off-by-one in stack check
ARM: fixup SMP alternatives in modules
ARM: make SWP emulation explicit on !CPU_USE_DOMAINS
ARM: Avoid building unsafe kernels on OMAP2 and MX3
ARM: pxa: Properly configure PWM period for palm27x
ARM: pxa: only save/restore registers when pm functions are defined
ARM: pxa/colibri: use correct SD detect pin
ARM: pxa: fix mfpr_sync to read from valid offset
The pointer math in omap_mbox_get() is not quite right, and leads to
passing NULL to strcmp() when searching for an mbox that is not first
in the list.
Convert to using array indexing as is done in all the other functions
which walk the mbox list.
Tested on OMAP2420/n810, OMAP3630/zoom3, OMAP4430/Blaze
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IRQ numbering for the IVA and DSP mailboxes was switched due
to the wrong ordering in the OMAP2 mbox list. Switch the ordering
so DSP is first and matches all the other SoCs.
Tested on OMAP2420/n810.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We use it in non __cpuinit code now too so drop marker.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20110211171754.GA21047@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
commit a3c08e5d(x86: Convert irq_chip access to new functions)
accidentally zapped desc = irq_to_desc(irq); in the vector loop.
So we lock some random irq descriptor.
Add it back.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org> # .37
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Ensure struct sys_device is declared in plat/pm.h
ARM: S5PV310: Cleanup System MMU
ARM: S5PV310: Add support System MMU on SMDKV310
The ptrace debug information register was advertising breakpoint and
watchpoint resources for unsupported debug architectures. This meant
that setting breakpoints on these architectures would appear to succeed,
although they would never fire in reality.
This patch fixes the breakpoint slot probing so that it returns 0 when
running on an unsupported debug architecture.
Reported-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reading baseline CP14 registers, other than DBGDIDR, when the OS Lock
is set leads to UNPREDICTABLE behaviour.
This patch ensures that we clear the OS lock before accessing anything
other than the DBGDIDR, thereby avoiding this behaviour.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
locomo_info isn't actually used as a platform_data on collie platform:
arm/mach-sa1100/collie.c:237: warning: ‘locomo_info’ defined but not used
So locomo driver doesn't setup IRQs correctly. Pass locomo_info to the
driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
rmk says: "You might as well make OABI_COMPAT depend on !THUMB2_KERNEL.
OABI userland is useless without FPA support."
nwfpe doesn't work with Thumb-2 anyway and will probably never get
ported, so I can't argue with that.
This patch implements the dependency change.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previously we were relying on it being pulled in by other headers for
the prototype of s3c24xx_irq_suspend() and s3c24xx_irq_resume().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch cleans following up.
- Moved definition of System MMU IPNUM into mach/sysmmu.h
- Removed useless SYSMMU_DEBUG configuration
- Removed useless header file plat/sysmmu.h
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The 's5pv310_device_sysmmu' is used on SMDKV310. But since it is not
compiled now, there is a build error. To fix this compilation error,
S5PV310_DEV_SYSMMU needs to be selected for SMDKV310 board.
This patch enables System MMU support on SMDKV310.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[kgene.kim@samsung.com: Adding description]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: bfin_5xx: split uart RX lock from uart port lock to avoid deadlock
68360serial: Plumb in rs_360_get_icount()
n_gsm: copy mtu over when configuring via ioctl interface
virtio: console: Move file back to drivers/char/
Since tail is the previous fp - 1, we need to compare the new fp with tail + 1
to ensure that we don't end up passing in the same tail again, in order to
avoid a potential infinite loop in the perf interrupt handler (which has been
observed to occur). A similar fix seems to be needed in the OProfile code.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With certain configurations, we inline the unlock functions in modules,
which results in SMP alternatives being created in modules. We need to
fix those up when loading a module to prevent undefined instruction
faults.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SWP emulation requires that CPU domain support is disabled in order to
work safely. Make that explicit in the kernel configuration to prevent
illegal configurations being generated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Additionally doing things conditionally upon smp_processor_id()
being zero is generally a bad idea, as this means CPU 0 cannot
be offlined and brought back online later again.
While there may be other places where this is done, I think adding
more of those should be avoided so that some day SMP can really
become "symmetrical".
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
LKML-Reference: <4D525C7E0200007800030EE1@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
OMAP2 (armv6) and MX3 turn off support for the V6K instructions, which
when they include support for SMP kernels means that the resulting
kernel is unsafe on SMP and can result in corrupted filesystems as we
end up using unsafe bitops.
Re-enable the use of V6K instructions on such kernels, and let such
kernels running on V6 CPUs eat undefined instruction faults which will
be much safer than filesystem corruption. Next merge window we can fix
this properly (as it requires a much bigger set of changes.)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The gs_index loading code uses the swapgs instruction to
switch to the user gs_base temporarily. This is unsave in an
lightweight exit-path in KVM on AMD because the
KERNEL_GS_BASE MSR is switches lazily. An NMI happening in
the critical path of load_gs_index may use the wrong GS_BASE
value then leading to unpredictable behavior, e.g. a
triple-fault.
This patch fixes the issue by making sure that load_gs_index
is called only with a valid KERNEL_GS_BASE value loaded in
KVM.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The use of wrong SD detect pin was introduced by this commit:
ARM: pxa: Push Colibri evalboard MFP into module files
This fixes it.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since mfpr_mmio_base[0] is not always valid on later SoCs,
fixed mpfr_sync() to read back from valid mfp offset always.
Signed-off-by: Yu Tang <ytang5@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
iommu_alloc_ctx() finds a zero bit in iommu->ctx_bitmap. It starts
searching from iommu->ctx_lowest_free to the end of the bitmap.
But the size argument to find_next_zero_bit() in iommu_alloc_ctx()
is wrong. It should be the bitmap size, not the maximum size to
search from the offset argument.
Fortunately iommu->ctx_lowest_free is almost unused and it will not
be more than 1. So the bug wasted only 1-bit at the end of
iommu->ctx_bitmap.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bitmap_set() instead of calling __set_bit() each bit.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The _TIF_WORK_MASK definition was removed in the clean up of MMU and
non-MMU arch/m68k/include/asm/thread_info*.h files (this was commit
cddafa3500, "merge MMU and non-MMU
thread_info.h").
It didn't get cleaned out of the entry.S code for the 68328 and 68360
based platforms. And it was replaced by a hard coded constant mask for
coldfire platforms. There is currently no need to mask any of these bits,
so fix all uses (and former uses) to check for any non-zero value.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ALSA: AACI: allow writes to MAINCR to take effect
ARM: Update mach-types
ARM: 6652/1: ep93xx: correct the end address of the AC97 memory resource
ARM: mxs/imx28: remove now unused clock lookup "fec.0"
ARM: mxs: fix clock base address missing
ARM: mxs: acknowledge gpio irq
ARM: mach-imx/mach-mx25_3ds: Fix section type
ARM: imx: Add VPR200 and MX51_3DS entries to uncompress.h
ARM i.MX23: use correct register for setting the rate
ARM i.MX23/28: remove secondary field from struct clk. It's unused
ARM i.MX28: use correct register for setting the rate
ARM i.MX28: fix bit operation
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix hcall tracepoint recursion
powerpc/numa: Fix bug in unmap_cpu_from_node
powerpc/numa: Disable VPHN on dedicated processor partitions
powerpc/numa: Add length when creating OF properties via VPHN
powerpc/numa: Check for all VPHN changes
powerpc/numa: Only use active VPHN count fields
powerpc/pseries: Remove unnecessary variable initializations in numa.c
powerpc/pseries: Fix brace placement in numa.c
powerpc/pseries: Fix typo in VPHN comments
powerpc: Fix some 6xx/7xxx CPU setup functions
powerpc: Pass the right cpu_spec to ->setup_cpu() on 64-bit
powerpc/book3e: Protect complex macro args in mmu-book3e.h
powerpc: Fix pfn_valid() when memory starts at a non-zero address
Fix msr instructions detection. The current code
just use msrclr for loading msr content and compare
it with proper MSR content. If msrclr is not implemented
r8 contains pc address.
Previous code wanted to use MSR carry bit but if msrclr
wasn't implemented carry wasn't cleared.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Do not disable irq in asm but use irq macros.
Systems with MSR=0 couldn't use pte_update function
because msrclr was hardcoded.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Patch: Fix IRQ flag handling naming
(sha1: f9ee29270c11dba7d0fe0b83ce47a4d8e8d2101)
introduced problem on system with MSR=0.
Signed-off-by: Michal Simek <monstr@monstr.eu>
The partial block handling in sha-s390 is broken when we get a
partial block that is followed by an update which fills it with
bytes left-over. Instead of storing the newly left-over bytes
at the start of the buffer, it will be stored immediately after
the previous partial block.
This patch fixes this by resetting the index pointer.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We reserve lowmem for the things that need it, like the ACPI
wakeup code, way early to guarantee availability. This happens
before we set up the proper pagetables, so set_memory_x() has no
effect.
Until we have a better solution, use an initcall to mark the
wakeup code executable.
Originally-by: Matthieu Castet <castet.matthieu@free.fr>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Matthias Hopf <mhopf@suse.de>
Cc: rjw@sisk.pl
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4D4F8019.2090104@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Spinlocks on shared processor partitions use H_YIELD to notify the
hypervisor we are waiting on another virtual CPU. Unfortunately this means
the hcall tracepoints can recurse.
The patch below adds a percpu depth and checks it on both the entry and
exit hcall tracepoints.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org
When converting to the new cpumask code I screwed up:
- if (cpu_isset(cpu, numa_cpumask_lookup_table[node])) {
- cpu_clear(cpu, numa_cpumask_lookup_table[node]);
+ if (cpumask_test_cpu(cpu, node_to_cpumask_map[node])) {
+ cpumask_set_cpu(cpu, node_to_cpumask_map[node]);
This was introduced in commit 25863de07a (powerpc/cpumask: Convert NUMA code
to new cpumask API)
Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is no need to start up the timer and monitor topology changes on a
dedicated processor partition, so disable it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The rest of the NUMA code expects an OF associativity property with
the first cell containing the length. Without this fix all topology changes
cause us to misparse the property and put the cpu into node 0.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The hypervisor uses unsigned 1 byte counters to signal topology changes to
the OS. Since they can wrap we need to check for any difference, not just if
the hypervisor count is greater than the previous count.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
VPHN supports up to 8 distance fields but the number of entries in
ibm,associativity-reference-points signifies how many are in use.
Don't look at all the VPHN counts, only distance_ref_points_depth
worth.
Since we already cap our distance metrics at MAX_DISTANCE_REF_POINTS,
use that to size the VPHN arrays and add a BUILD_BUG_ON to avoid it growing
larger than the VPHN maximum of 8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Correct a spelling error in VPHN comments in numa.c.
Signed-off-by: Jesse Larrew <jlarrew@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some of those functions try to adjust the CPU features, for example
to remove NAP support on some revisions. However, they seem to use
r5 as an index into the CPU table entry, which might have been right
a long time ago but no longer is. r4 is the right register to use.
This probably caused some off behaviours on some PowerMac variants
using 750cx or 7455 processor revisions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org
When calling setup_cpu() on 64-bit, we pass a pointer to the
cputable entry we have found. This used to be fine when cur_cpu_spec
was a pointer to that entry, but nowadays, we copy the entry into
a separate variable, and we do so before we call the setup_cpu()
callback. That means that any attempt by that callback at patching
the CPU table entry (to adjust CPU features for example) will patch
the wrong table.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
max_mapnr is a pfn, not an index innto mem_map[]. So don't add
ARCH_PFN_OFFSET a second time.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
m32r: Fixup last __do_IRQ leftover
genirq: Add missing status flags to modification mask
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure the stack is set up before we use it
x86, mtrr: Avoid MTRR reprogramming on BP during boot on UP platforms
x86, nx: Don't force pages RW when setting NX bits
FREQ is a ridiculously short name for a platform-specific macro in a
generic header, and it now conflicts with an enumeration in the
gspca/ov519 driver.
Also delete conditional reference to ixp4xx_get_board_tick_rate()
which is not defined anywhere.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Queues should be empty when released, if not, there is a safety valve.
Make sure the queue is usable after it triggers.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Somehow I managed to miss the last __do_IRQ caller when I cleanup the
remaining users. m32r is fully converted to the generic irq layer, but
I managed to not commit the conversion of __do_IRQ() to
generic_handle_irq() after compile testing the quilt series :(
Pointed-out-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
The last register is at offset 0xa8 making the resource end to be 0xac - 1
instead of 0xb0 - 1.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since checkin ebba638ae7 we call
verify_cpu even in 32-bit mode. Unfortunately, calling a function
means using the stack, and the stack pointer was not initialized in
the 32-bit setup code! This code initializes the stack pointer, and
simplifies the interface slightly since it is easier to rely on just a
pointer value rather than a descriptor; we need to have different
values for the segment register anyway.
This retains start_stack as a virtual address, even though a physical
address would be more convenient for 32 bits; the 64-bit code wants
the other way around...
Reported-by: Matthieu Castet <castet.matthieu@free.fr>
LKML-Reference: <4D41E86D.8060205@free.fr>
Tested-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Don't allow all users to change timer settings.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do not create mux debugfs files as world-writable.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The RX lock is used to protect the RX buffer from concurrent access in DMA
mode between the timer and RX interrupt routines. It is independent from
the uart lock which is used to protect the TX buffer. It is possible for
a uart TX transfer to be started up from the RX interrupt handler if low
latency is enabled. So we need to split the locks to avoid deadlocking in
this situation.
In PIO mode, the RX lock is not necessary because the handle_simple_irq
and handle_level_irq functions ensure driver interrupt handlers are called
once on one core.
And now that the RX path has its own lock, the TX interrupt has nothing to
do with the RX path, so disabling it at the same time.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clearing the cpu in prev's mm_cpumask early will avoid the flush tlb
IPI's while the cr3 is still pointing to the prev mm. And this window
can lead to the possibility of bogus TLB fills resulting in strange
failures. One such problematic scenario is mentioned below.
T1. CPU-1 is context switching from mm1 to mm2 context and got a NMI
etc between the point of clearing the cpu from the mm_cpumask(mm1)
and before reloading the cr3 with the new mm2.
T2. CPU-2 is tearing down a specific vma for mm1 and will proceed with
flushing the TLB for mm1. It doesn't send the flush TLB to CPU-1
as it doesn't see that cpu listed in the mm_cpumask(mm1).
T3. After the TLB flush is complete, CPU-2 goes ahead and frees the
page-table pages associated with the removed vma mapping.
T4. CPU-2 now allocates those freed page-table pages for something
else.
T5. As the CR3 and TLB caches for mm1 is still active on CPU-1, CPU-1
can potentially speculate and walk through the page-table caches
and can insert new TLB entries. As the page-table pages are
already freed and being used on CPU-2, this page walk can
potentially insert a bogus global TLB entry depending on the
(random) contents of the page that is being used on CPU-2.
T6. This bogus TLB entry being global will be active across future CR3
changes and can result in weird memory corruption etc.
To avoid this issue, for the prev mm that is handing over the cpu to
another mm, clear the cpu from the mm_cpumask(prev) after the cr3 is
changed.
Marking it for -stable, though we haven't seen any reported failure that
can be attributed to this.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org [v2.6.32+]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Markus Kohn ran into a hard hang regression on an acer aspire
1310, when acpi is enabled. git bisect showed the following
commit as the bad one that introduced the boot regression.
commit d0af9eed5a
Author: Suresh Siddha <suresh.b.siddha@intel.com>
Date: Wed Aug 19 18:05:36 2009 -0700
x86, pat/mtrr: Rendezvous all the cpus for MTRR/PAT init
Because of the UP configuration of that platform,
native_smp_prepare_cpus() bailed out (in smp_sanity_check())
before doing the set_mtrr_aps_delayed_init()
Further down the boot path, native_smp_cpus_done() will call the
delayed MTRR initialization for the AP's (mtrr_aps_init()) with
mtrr_aps_delayed_init not set. This resulted in the boot
processor reprogramming its MTRR's to the values seen during the
start of the OS boot. While this is not needed ideally, this
shouldn't have caused any side-effects. This is because the
reprogramming of MTRR's (set_mtrr_state() that gets called via
set_mtrr()) will check if the live register contents are
different from what is being asked to write and will do the actual
write only if they are different.
BP's mtrr state is read during the start of the OS boot and
typically nothing would have changed when we ask to reprogram it
on BP again because of the above scenario on an UP platform. So
on a normal UP platform no reprogramming of BP MTRR MSR's
happens and all is well.
However, on this platform, bios seems to be modifying the fixed
mtrr range registers between the start of OS boot and when we
double check the live registers for reprogramming BP MTRR
registers. And as the live registers are modified, we end up
reprogramming the MTRR's to the state seen during the start of
the OS boot.
During ACPI initialization, something in the bios (probably smi
handler?) don't like this fact and results in a hard lockup.
We didn't see this boot hang issue on this platform before the
commit d0af9eed5a, because only
the AP's (if any) will program its MTRR's to the value that BP
had at the start of the OS boot.
Fix this issue by checking mtrr_aps_delayed_init before
continuing further in the mtrr_aps_init(). Now, only AP's (if
any) will program its MTRR's to the BP values during boot.
Addresses https://bugzilla.novell.com/show_bug.cgi?id=623393
[ By the way, this behavior of the bios modifying MTRR's after the start
of the OS boot is not common and the kernel is not prepared to
handle this situation well. Irrespective of this issue, during
suspend/resume, linux kernel will try to reprogram the BP's MTRR values
to the values seen during the start of the OS boot. So suspend/resume might
be already broken on this platform for all linux kernel versions. ]
Reported-and-bisected-by: Markus Kohn <jabber@gmx.org>
Tested-by: Markus Kohn <jabber@gmx.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Thomas Renninger <trenn@novell.com>
Cc: Rafael Wysocki <rjw@novell.com>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: stable@kernel.org # [v2.6.32+]
LKML-Reference: <1296694975.4418.402.camel@sbsiddha-MOBL3.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Xen want page table pages read only.
But the initial page table (from head_*.S) live in .data or .bss.
That was broken by 64edc8ed5f. There is
absolutely no reason to force these pages RW after they have already
been marked RO.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Panda uses both twl6030 otg phy(vbus, id) and internal
phy(data lines, DP/DM), so removes usb_nop_xceiv_register to make
twl6030 otg driver working since current otg code only supports
one global transceiver. Otherwise, musb doesn't work without
the remove.
Reviewd-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes bug introduced in revision:
f8e9e98454
omap1: DMA: move LCD related code from plat-omap to mach-omap1
The code introduced by this patch didn't consider any other CPUs but OMAP1510,
which rendered OMAP310 -- which has the same LCD controller -- non-working. Use
cpu_is_omap15xx() instead of cpu_is_omap1510() to squash this issue.
Bug found on Palm Zire 71 hardware.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes a wrongly used lcd enable pin.
The Devkit8000 uses twl4030_ledA configured as output gpio only for
the lcd enable line. twl4030_gpio.1 is used through the generic
gpio functions while ledA is used via low level twl4030 calls.
This patch removes the low level calls and use the generic gpio functions
for initialization and use of ledA. This patch also fixes a bug where the
lcd would not power down when blanking.
Further this patch fixes an indentation issue. The comment line uses
eight whitespace and is replaced with a hard tab.
gpio_request + gpio_direction_output are replaced with gpio_request_one.
The return value of gpio_request_one is used to set the value of the
gpio to -EINVAL when unsuccessful, so that gpio_is_valid can detect the
unsuccessful request. But already successful requested gpios are not freed.
Reported-by: Daniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the commit 7579025130 (regulator:
Factor out voltage set operation into a separate function) fixed voltage
regulator setup will fail if there are voltage constraints defined. This
made MMC unusable on this board. Fix by just deleting those redundant
constraints.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Reviewed-by: Jarkko Nikula <jhnikula@gmail.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix ASM optimized code for LE
microblaze: Fix unaligned issue on MMU system with BS=0 DIV=1
microblaze: Fix DTB passing from bootloader
Since commit f0e98c387e ("[SPARC]: Fix
link errors with gcc-4.3") the MNA trap handler does not emulate
stores to unaligned addresses correctly. MNA operation from both
kernel and user space are affected.
A typical effect of this bug is nr_frags in skbs are overwritten
during buffer copying/checksum-calculation, or maximally 6 bytes
of data in the network buffer will be overwitten with garbage.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the sh73a0 CPGA to support clocks for CEU
and MIPI-CSI. This includes MSTP bits for CSI and
CEU and div6 clkdev bindings for VCK1-3.
Fix the order of the MSTP32 entries in the clkdev
table while at it.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a 100 ms delay after the MIPI-DSI panel reset to
fix issue related to the LCD panel not starting properly
at boot up time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It is necessary to set array of struct platform_device in
early_platform_add_devices().
arch/sh/kernel/cpu/sh4/setup-sh7750.c: In function ‘plat_early_device_setup’:
arch/sh/kernel/cpu/sh4/setup-sh7750.c:260: warning: passing argument 1 of ‘early_platform_add_devices’ from incompatible pointer type
include/linux/platform_device.h:159: note: expected ‘struct platform_device **’ but argument is of type ‘struct platform_device *’
arch/sh/kernel/cpu/sh4/setup-sh7750.c:262: warning: passing argument 1 of ‘early_platform_add_devices’ from incompatible pointer type
include/linux/platform_device.h:159: note: expected ‘struct platform_device **’ but argument is of type ‘struct platform_device *’
arch/sh/kernel/cpu/sh4/setup-sh7750.c:263: warning: passing argument 1 of ‘early_platform_add_devices’ from incompatible pointer type
include/linux/platform_device.h:159: note: expected ‘struct platform_device **’ but argument is of type ‘struct platform_device *’
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
By commit 3252b11fc4,
machtypes.h moved to include/generated.
However, this forgot kernel/cpu/sh4/setup-sh7750.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit b2878fa (ARM: mx28: update clock and device name for dual fec
support) added only the new lookups without removing the old one.
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
arch/arm/mach-omap2/dma.c: Convert IS_ERR result to PTR_ERR
arm: omap2: mux: fix compile warning
omap1: Simplify use of omap_irq_flags
omap2+: Fix unused variable warning for omap_irq_base
Allow non-ARM SMP processors to use the SMP_ON_UP feature. CPUs
supporting SMP must have the new CPU ID format, so check for this first.
Then check for ARM11MPCore, which fails the MPIDR check. Lastly check
the MPIDR reports multiprocessing extensions and that the CPU is part of
a multiprocessing system.
Cc: <stable@kernel.org>
Reported-and-Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These errors were found by cppcheck:
arch/arm/mach-omap2/smartreflex.c:784: error: Possible null pointer dereference: sr_info
arch/arm/mach-omap2/smartreflex.c:799: error: Possible null pointer dereference: sr_info
Both conditional statements are executed when sr_info == NULL,
so accessing sr_info->voltdm would fail.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
sr_info was allocated and needs a kfree before returning.
This error was reported by cppcheck:
arch/arm/mach-omap2/smartreflex.c:837: error: Memory leak: sr_info
To: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Shweta Gulati <shweta.gulati@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The temporary string holding the directory name to be created should
be released.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Ensure that the ISA/PCI IO space accessors are properly ordered on
ARMv6+ architectures. These should always be ordered with respect to
all other accesses.
This also fixes __iormb() and __iowmb() not being visible to ioread/
iowrite if a platform defines its own MMIO accessors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Disable the initrd if the passed address already overlaps the reserved
region. This avoids oopses on Netwinders when NeTTrom tells the kernel
that an initrd is located at mem+4MB, but this overlaps the BSS,
resulting in the kernels in-use BSS being freed.
This should be applied to v2.6.37-stable.
Cc: <stable@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
0ea1293 (arm: return both physical and virtual addresses from addruart)
changed the way the 'addruart' worked, making it return both the virt
and phys addresses. Unfortunately, for footbridge, these were reversed.
Fix that. Tested on Netwinder.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
6f9a3c33 "[S390] cleanup s390 Kconfig" accidentally changed
the default for CONFIG_CHSC_SCH. Reset it to m.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The implementation of the cache flushing interfaces on the s390
is identical with the default implementation in asm-generic.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix this build error with !CONFIG_SWAP caused by tranparent huge pages support:
In file included from mm/pgtable-generic.c:9:0:
/linux-2.6/arch/s390/include/asm/tlb.h: In function 'tlb_remove_page':
/linux-2.6/arch/s390/include/asm/tlb.h:92:2: error: implicit declaration of function 'page_cache_release'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The uaccess functions copy_in_user_std and clear_user_std fail to
switch back from secondary space mode to primary space mode with sacf
in case of an unresolvable page fault. We need to make sure that the
switch back to primary mode is done in all cases, otherwise the code
following the uaccess inline assembly will crash.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After page_table_free_rcu removed a page from the pgtable_list
page_table_free better not add it again. Otherwise a page_table_alloc
can reuse a page table fragment that is still in the rcu process.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Microblaze little-endian doesn't support ASM optimized library
functions(memcpy/memmove). Kconfig doens't contain
any information about endian that's why it is necessary to
check it in the source code.
The code is used with barrel shifter is used.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Unaligned code use shift for finding register operand.
There is used BSRLI(r8,r8,2) macro which is expand for BS=0, DIV=1
by
ori rD, r0, (1 << imm); \
idivu rD, rD, rA
but if rD is equal rA then ori instruction rewrite value which
should be devide.
The patch remove this macro which use idivu instruction because
idivu takes 32/34 cycles. The highest shifting is 20 which takes
20 cycles.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Little endian system needs to check OF_DT_HEADER
but it is swapped because it is in big-endian.
Microblaze LE provides lwr instruction which loads
magic number in BIG endian format which can be compared.
There is used the fact that if you write 0x1 as word
and load it as byte then you get for big-endian zero
and 1 for little-endian.
Signed-off-by: Michal Simek <monstr@monstr.eu>
* 'stable/bug-fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/setup: Route halt operations to safe_halt pvop.
xen/e820: Guard against E820_RAM not having page-aligned size or start.
xen/p2m: Mark INVALID_P2M_ENTRY the mfn_list past max_pfn.
This code elsewhere returns a negative constant to an indicate an error,
while IS_ERR returns the result of a >= operation.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
if (...) { ...
- return IS_ERR(x);
+ return PTR_ERR(x);
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8419fdbaf2
(omap2+: Add omap_mux_get_by_name) introduced the following
compile warning:
arch/arm/mach-omap2/mux.c: In function '_omap_mux_get_by_name':
arch/arm/mach-omap2/mux.c:163:17: warning: 'found_mode' may be used
uninitialized in this function
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 03a9e51261
(omap1: Use asm_irq_flags for entry-macro.S) added support
for multi-omap builds with addition of the omap_irq_flags.
Commit 9f9605c2ed
(omap2+: Fix unused variable warning for omap_irq_base)
simplified omap2+ entry-macro.S by moving omap_irq_flags
out of entry-macro.S.
Simplify omap1 entry-macro.S in a similar way to keep the
code consistent. Based on a similar earlier patch for omap2+
by Russell King <rmk+kernel@arm.linux.org.uk>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 5d190c4010
(omap2+: Initialize omap_irq_base for entry-macro.S from
platform code) simplified the handling of omap_irq_base
for multi-omap builds. However, this patch also introduced
a build warning for !MULTI_OMAP2 builds:
arch/arm/mach-omap2/io.c: In function 'omap_irq_base_init':
arch/arm/mach-omap2/io.c:322: warning: unused variable 'omap_irq_base'
Fix this by removing the ifdef. Also simplify things further
by moving omap_irq_base out of entry-macro.S.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
percpu, x86: Fix percpu_xchg_op()
x86: Remove left over system_64.h
x86-64: Don't use pointer to out-of-scope variable in dump_trace()
This patch fixes some issues with raw event validation on
Pentium 4 (Netburst) based processors.
As I was testing libpfm4 Netburst support, I ran into two
problems in the p4_validate_raw_event() function:
- the shared field must be checked ONLY when HT is on
- the binding to ESCR register was missing
The second item was causing raw events to not be encoded
correctly compared to generic PMU events.
With this patch, I can now pass Netburst events to libpfm4
examples and get meaningful results:
$ task -e global_power_events🏃u noploop 1
noploop for 1 seconds
3,206,304,898 global_power_events:running
Signed-off-by: Stephane Eranian <eranian@google.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: peterz@infradead.org
Cc: paulus@samba.org
Cc: davem@davemloft.net
Cc: fweisbec@gmail.com
Cc: perfmon2-devel@lists.sf.net
Cc: eranian@gmail.com
Cc: robert.richter@amd.com
Cc: acme@redhat.com
Cc: gorcunov@gmail.com
Cc: ming.m.lin@intel.com
LKML-Reference: <4d3efb2f.1252d80a.1a80.ffffc83f@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With this patch, the cpuidle driver does not load and
does not issue the mwait operations. Instead the hypervisor
is doing them (b/c we call the safe_halt pvops call).
This fixes quite a lot of bootup issues wherein the user had
to force interrupts for the continuation of the bootup.
Details are discussed in:
http://lists.xensource.com/archives/html/xen-devel/2011-01/msg00535.html
[v2: Wrote the commit description]
Reported-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Tested-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Under Dell Inspiron 1525, and Intel SandyBridge SDP's the
BIOS e820 RAM is not page-aligned:
[ 0.000000] Xen: 0000000000100000 - 00000000df66d800 (usable)
We were not handling that and ended up setting up a pagetable
that included up to df66e000 with the disastrous effect that when
memset(NODE_DATA(nodeid), 0, sizeof(pg_data_t));
tried to clear the page it would crash at the 2K mark.
Initially reported by Michael Young @
http://lists.xensource.com/archives/html/xen-devel/2011-01/msg00108.html
The fix is to page-align the size and also take into consideration
the start of the E820 (in case that is not page-aligned either). This
fixes the bootup failure on those affected machines.
This patch is a rework of the Micheal A Young initial patch and
considers the case if the start is not page-aligned.
Reported-by: Michael A Young <m.a.young@durham.ac.uk>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Michael A Young <m.a.young@durham.ac.uk>
In case the mfn_list does not have enough entries to fill
a p2m page we do not want the entries from max_pfn up to
the boundary to be filled with unknown values. Hence
set them to INVALID_P2M_ENTRY.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
A future patch will export gic_mask_irq and gic_unmask_irq.
Rename the pointers in arch/arm/mach-tegra/irq.c to avoid
a compile error.
Signed-off-by: Colin Cross <ccross@android.com>
Commit 37337a8d5e, "ARM: tegra: irq_data
conversion." missed changing one reference to 'irq' in the function
tegra_gpio_irq_set_type(). This patch fixes the build error.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Currently, on HS/EMU devices, MPU power state forced to on during PM
init by the save secure RAM code. Rather than forcing the state of
MPU powerdomain to on, simply read the current value and restore it
after the ROM code has run.
This only affects the !CPUidle case since when CPUidle is enabled, the
MPU power state is dynamically changed by CPUidle. In the !CPUidle
case, MPU power state is initialized once at init and never touched.
Acked-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Always allow backtraces when using oprofile on ARM, even if a PMU
isn't present. Restores functionality originally introduced in commit
1b7b56982f ("oprofile: Always allow
backtraces on ARM") by Richard Purdie.
It is not that obvious, but there is now only one oprofile_arch_init()
function. So the .backtrace callback is available also in timer mode.
Implemented by removing code and using stubs for oprofile_perf_{init,
exit} provided by <linux/oprofile.h>. This allows cleaning of other
architecture specific implementations too.
Cc: stable@kernel.org # 37.x
Signed-off-by: Ari Kauppi <kauppi@papupata.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch adds the linux/mm.h header file to the AVR32 arch pgalloc.c
implementation to fix the undefined reference to pgtable_page_ctor() and
pgtable_page_dtor().
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
This fixes a machine hang after a gpio irq triggered.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These recent percpu commits:
2485b6464c: x86,percpu: Move out of place 64 bit ops into X86_64 section
8270137a0d: cpuops: Use cmpxchg for xchg to avoid lock semantics
Caused this 'perf top' crash:
Kernel panic - not syncing: Fatal exception in interrupt
Pid: 0, comm: swapper Tainted: G D
2.6.38-rc2-00181-gef71723 #413 Call Trace: <IRQ> [<ffffffff810465b5>]
? panic
? kmsg_dump
? kmsg_dump
? oops_end
? no_context
? __bad_area_nosemaphore
? perf_output_begin
? bad_area_nosemaphore
? do_page_fault
? __task_pid_nr_ns
? perf_event_tid
? __perf_event_header__init_id
? validate_chain
? perf_output_sample
? trace_hardirqs_off
? page_fault
? irq_work_run
? update_process_times
? tick_sched_timer
? tick_sched_timer
? __run_hrtimer
? hrtimer_interrupt
? account_system_vtime
? smp_apic_timer_interrupt
? apic_timer_interrupt
...
Looking at assembly code, I found:
list = this_cpu_xchg(irq_work_list, NULL);
gives this wrong code : (gcc-4.1.2 cross compiler)
ffffffff810bc45e:
mov %gs:0xead0,%rax
cmpxchg %rax,%gs:0xead0
jne ffffffff810bc45e <irq_work_run+0x3e>
test %rax,%rax
je ffffffff810bc4aa <irq_work_run+0x8a>
Tell gcc we dirty eax/rax register in percpu_xchg_op()
Compiler must use another register to store pxo_new__
We also dont need to reload percpu value after a jump,
since a 'failed' cmpxchg already updated eax/rax
Wrong generated code was :
xor %rax,%rax /* load 0 into %rax */
1: mov %gs:0xead0,%rax
cmpxchg %rax,%gs:0xead0
jne 1b
test %rax,%rax
After patch :
xor %rdx,%rdx /* load 0 into %rdx */
mov %gs:0xead0,%rax
1: cmpxchg %rdx,%gs:0xead0
jne 1b:
test %rax,%rax
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Tejun Heo <tj@kernel.org>
LKML-Reference: <1295973114.3588.312.camel@edumazet-laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Left-over from the x86 merge ...
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D3E23D1.7010405@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - pass touch resolution to clients through input_absinfo
Input: wacom - add 2 Bamboo Pen and touch models
Input: sysrq - ensure sysrq_enabled and __sysrq_enabled are consistent
Input: sparse-keymap - fix KEY_VSW handling in sparse_keymap_setup
Input: tegra-kbc - add tegra keyboard driver
Input: gpio_keys - switch to using request_any_context_irq
Input: serio - allow registered drivers to get status flag
Input: ct82710c - return proper error code for ct82c710_open
Input: bu21013_ts - added regulator support
Input: bu21013_ts - remove duplicate resolution parameters
Input: tnetv107x-ts - don't treat NULL clk as an error
Input: tnetv107x-keypad - don't treat NULL clk as an error
Fix up trivial conflicts in drivers/input/keyboard/Makefile due to
additions of tc3589x/Tegra drivers
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes TRANSPARENT_HUGEPAGE=y with PARAVIRT=y and HIGHMEM64=n.
The #ifdef that this patch removes was erratically introduced to fix a
build error for noPAE (where pmd.pmd doesn't exist). So then the kernel
built but it failed at runtime because set_pmd_at was a noop. This will
correct it by enabling set_pmd_at for noPAE mode too.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: werner <w.landgraf@ru.ru>
Reported-by: Minchan Kim <minchan.kim@gmail.com>
Tested-by: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ALSA: AACI: fix timeout duration
ALSA: AACI: fix timeout condition checking
ARM: 6636/1: ep93xx: default multiplexed gpio ports to gpio mode
ARM: 6637/1: Make the argument to virt_to_phys() "const volatile"
ARM: twd: ensure timer reload is reprogrammed on entry to periodic mode
ARM: 6635/2: Configure reference clock for Versatile Express timers
ARM: versatile: name configuration options after actual board names
ARM: realview: name configuration options after actual board names
ARM: realview,vexpress: fix section mismatch warning for pen_release
ARM: 6632/3: mmci: stop using the blockend interrupts
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix build of sh7750 base boards
sh: update INTC to clear IRQ sense valid flag
sh: Fix sh build failure when CONFIG_SFC=m
sh: fix MSIOF0 SPI on ecovec: it conflicts with VOU
sh: support XZ-compressed kernel.
sh: Fix up breakage from asm-generic/pgtable.h changes.
The EP93xx C and D GPIO ports are multiplexed with the Keypad Interface
peripheral. At power-up they default into non-GPIO mode with the Key
Matrix controller enabled so these ports are unusable for GPIO. Note
that the Keypad Interface peripheral is only available in the EP9307,
EP9312, and EP9315 processor variants.
The keypad support will clear the DeviceConfig bits appropriately to
enable the Keypad Interface when the driver is loaded. And, when the
driver is unloaded it will set the bits to return the ports to GPIO mode.
To make these ports available for GPIO after power-up on all EP93xx
processor variants, set the KEYS and GONK bits in the DeviceConfig
register.
Similarly, the E, G, and H ports are multiplexed with the IDE Interface
peripheral. At power-up these also default into non-GPIO mode. Note
that the IDE peripheral is only available in the EP9312 and EP9315
processor variants.
Since an IDE driver is not even available in mainline, set the EONIDE,
GONIDE, and HONIDE bits in the DeviceConfig register so that these
ports will be available for GPIO use after power-up.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Changing the virt_to_phys() argument to "const volatile void *" avoids
compiler warnings in some situations where this function is used.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the twd timer reload value is reprogrammed each time we
enter periodic mode. This ensures that the reload value is always
reset correctly.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Timers on Versatile Express mainboard are used as system clock/event
sources. Driver assumes that they are clocked with 1MHz signal.
Old V2M firmware apparently configured it by default, but on newer
boards one can observe that "sleep 1" command takes over 30 seconds
to finish, as the timers are fed with 32kHz instead...
This patch performs required magic and also removes code clearing
timer's control registers, as exactly the same operations are
performed by the timer driver few jiffies later.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the option text to those which appear on the front of the
appropriate board user guides. This gives consistent board naming, and
makes it obvious which option is for which platform.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As no one seems to really know which configuration options tie up with
which boards, I thought I'd do some investigation and try to work it
out. After discussion with some folk in linaro, I think I have this
nailed.
The names are updated to use the name on the front of the appropriate
board user guide for the various baseboards, which I've taken to be
the official name for each board.
I haven't significantly updated the descriptions for the tiles as that
is even less clear - as far as I can see on ARMs website, there is no
Cortex-A9 tile for Realview EB - only ARM11MPCore, ARM1156T2F-S,
ARM1176TZF-S and Cortex-R4F. So exactly what this 'Multicore Cortex-A9
Tile' is...
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
