This patch adds rampatch download compatibility for ROME >= 3.2.
Starting with ROME 3.2, the 'download mode' field of the rampatch
header indicates if the controller acknowledges (or not) the received
rampatch segments. If not, we need to send all the segments without
expecting any event from the controller (except for the last segment).
Goal is (I assume) to speed-up rampatch download.
This fixes BT on Dragonboard-600c P2 which includes the following BT
controller:
hci0: ROME Patch Version Request
hci0: Product:0x00000008
hci0: Patch :0x00000111
hci0: ROM :0x00000302
hci0: SOC :0x00000023
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When both CONFIG_BT_HCIUART_INTEL and CONFIG_BT_HCIUART_BCM are not
selected, sparse complains like this:
drivers/bluetooth/hci_ldisc.c:437:9: warning: switch with no cases
Fix the sparse warning by proving a default switch case.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Initialize hw_name to "BCM", this avoids the need for a number of NULL
checks on hw_name later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_setup_patchram() starts with initializing the controller (and
getting the firmware filename) and then after loading the firmware,
does a re-init. This almost entirely duplicates the code in
btbcm_initialize(), use that function instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_finalize() does a re-init of the controller, which is almost the
same as the initial init. Modify btbcm_initialize() so that it can be
used for this re-init and modify btbcm_finalize() to use it.
As an added bonus this also makes the dev_info from btbcm_finalize()
use the proper hw_name instead of always printing "BCM".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make btbcm_initialize() also work for USB connected device,
btbcm_initialize() and btbcm_setup_patchram() are quite similar,
this is a preparation patch for making btbcm_setup_patchram() use
btbcm_initialize() to remove the code duplication.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We are using the same loop in both the UART and USB bus cases, refactor
things a bit to share the loop.
This is mostly meant to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_setup_patchram() was using the upper nibble of the revision code to
determine if we are dealing with an uart or USB connected bcm-bt device,
but just as btbcm_initialize() has started accepting 1 and 2 as uart
connected devices, I've now encountered an USB connected device (0a5c:216c)
which has 0 in the upper nibble. So it seems that the upper nibble is not
really a reliable indicator of the bus type.
Instead check hdev->bus which does give us a reliable indication. This
fixes the patchram code trying to load the patchram by the fallback BCM.hcd
filename, now it correctly requests BCM43142A0-0a5c-216c.hcd.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support for Qualcomm serial slave devices. Probe the serial device,
retrieve its maximum speed and register a new hci uart device.
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
AOSP use userspace firmware loader to load firmwares, which will
return -EAGAIN in case qca/rampatch_00440302.bin is not found.
Since there is no rampatch for dragonboard820c QCA controller
revision, just make it work as is.
CC: Loic Poulain <loic.poulain@linaro.org>
CC: Nicolas Dechesne <nicolas.dechesne@linaro.org>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johan Hedberg <johan.hedberg@gmail.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
HCI RX/TX byte counters were only incremented when sending ACL packets.
To reflect the real HCI traffic, we need to increment these counters on
HCI events and HCI commands as well.
Increment error counter on rpmsg errors.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Interrupts specified through an "Interrupt" ACPI resource (versus through
a "GpioInt" resource) are now always assumed to be active low.
When this change was originally made the Thinkpad 8 quirk was kept around
because it was uncertain if the Thinkpad 8 uses an "Interrupt" or a
"GpioInt" resource.
Bug https://bugzilla.kernel.org/show_bug.cgi?id=196701 has a DSDT for the
Thinkpad 8 attached and it uses an "Interrupt" resource, so the quirk is
not necessary and the quirk, as well as the irq-active-low quirk handling
code can be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Meegopad T08 hdmi-stick (think Intel computestick) has a brcm43430
wifi/bt combo chip. The BCM2E90 ACPI device describing the BT part does
contain a valid ActiveLow GpioInt entry, but the GPIO it points to never
goes low, so either the IRQ pin is not connected, or the ACPI resource-
table points to the wrong GPIO.
Eitherway things will not work if we try to use the specified IRQ, this
commits adds a DMI based broken-irq blacklist and disables use of the IRQ
and thus also runtime-pm for devices on this list.
This blacklist starts with the the Meegopad T08, fixing bluetooth not
working on this hdmi-stick. Since this is not a battery powered device
the loss of runtime-pm is not really an issue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Dell XPS 13 9360 uses a QCA Rome chip which needs to be reset
(and have its firmware reloaded) for bluetooth to work after
suspend/resume.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Cc: stable@vger.kernel.org
Cc: Garrett LeSage <glesage@redhat.com>
Reported-and-tested-by: Garrett LeSage <glesage@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jeremy Cline correctly points out in rhbz#1514836 that a device where the
QCA rome chipset needs the USB_QUIRK_RESET_RESUME quirk, may also ship
with a different wifi/bt chipset in some configurations.
If that is the case then we are needlessly penalizing those other chipsets
with a reset-resume quirk, typically causing 0.4W extra power use because
this disables runtime-pm.
This commit moves the DMI table check to a btusb_check_needs_reset_resume()
helper (so that we can easily also call it for other chipsets) and calls
this new helper only for QCA_ROME chipsets for now.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Cc: stable@vger.kernel.org
Cc: Jeremy Cline <jcline@redhat.com>
Suggested-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit f44cb4b19e ("Bluetooth: btusb: Fix quirk for Atheros
1525/QCA6174") is causing bluetooth to no longer work for several
people, see: https://bugzilla.redhat.com/show_bug.cgi?id=1568911
So lets revert it for now and try to find another solution for
devices which need the modified quirk.
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA Rome controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Vic Wei <vwei@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As Interrupt resource specified IRQs are now assumed to be always
active-low the DMI quirk for the MINIX Z83-4 is no longer required.
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With patch 279c936153 the btuart_cs driver has been deprecated in
favor of serial_cs + hci_uart combination.
static struct pcmcia_device_id btuart_ids[] = {
/* don't use this driver. Use serial_cs + hci_uart instead */
PCMCIA_DEVICE_NULL
};
Intead of keeping it around, just remove it since it is not even
assigned to any PCMCIA identifiers anymore.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When adding the alignment and padding support for H:4 packet processing
for the Nokia driver, it broke the h4_recv_buf usage within bpa10x
driver. To fix this use a separate helper function and placing it into a
dedicated h4_recv.h header file.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCILL or eHCILL protocol from TI is actually an H:4 protocol with a
few extra events and thus can also use the h4_recv_buf helper. Instead
of open coding the same funtionality add the extra events to the packet
description table and use h4_recv_buf.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that we need just an ACPI HID in the table, and the driver auto-
configures itself otherwise, we can easily add a bunch of known ACPI HIDs.
This avoids having to add these 1 by 1 as devices with one are encountered
by users.
This commit may seem as if it simply adds all IDs between BCM2E00-BCM2EAC,
but that is not true, all these IDs were found in actual .inf files and
the range is not entirely continuous, the following IDs are not added:
BCM2E6A, BCM2E6C, BCM2E8F and BCM2E91 because I did not see these in any
.inf files. As for the large amount of IDs this seems to be caused by
Broadcom using a separate ID for every bluetooth module using their
chips. E.g. BCM2EA6 seems to be specifically for the Raspberry Pi 3.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since I've been doing a lot of work on Linux Bay Trail / Cherry Trail
support, I've gathered a collection of ACPI DSDTs from about 50 such
machines.
Looking at these DSTDs many have an ACPI device entry describing a bcm
bluetooth device (often disabled in the DSDT), quite a few of these ACPI
device entries have a resource-table where the order does not match with
the order currently associated with the HID of that entry in the
bcm_acpi_match table.
Looking at the Windows .inf files, there is nothing indicating a specific
order there, so I believe that there is no 1:1 mapping between the ACPI
HID and the order in which the resources are listed.
Therefor this commit replaces the hardcoded mapping based on ACPI HID,
with code which actually checks in which order the resources are listed
and bases the gpio-mapping on that.
This should ensure that we always pick the right mapping and this will
make adding new ACPI HIDs to the driver easier.
This has been tested on the following devices:
-Asus T100CHI BCM2E39 / brcmfmac43241b4-sdio / BCM4324B3-37.4M.hcd
-Asus T100TA BCM2E39 / brcmfmac43241b4-sdio / BCM4324B3-37.4M.hcd
-Asus T200TA BCM2E65 / brcmfmac43340-sdio / BCM43341B0-37.4M.hcd
-Jumper ezPad mini 3 BCM2E74 / brcmfmac43430a0-sdio / BCM4343A0-26M.hcd
-Acer Iconia Tab8 w1-8 BCM2E83 / brcmfmac4330-sdio / BCM4330B1-26M.hcd
-Chuwi Vi8 plus(CWI519) BCM2EAA / brcmfmac43430-sdio / BCM43430A1-26M.hcd
Which together cover all 3 combinations of using an Interrupt resource /
GpioInt resource as first resource / GpioInt resource as last resource.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We declare the same set of const acpi_gpio_params twice with different
names, besides the needless duplication this naming leads to a sortof
double indirection which also makes it harder to see how the mapping is
actually setup.
This commit renames the first set to have generic names, which better
describe the contents of the mapping and drops the second set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add 6 new ACPI HIDs to enable bluetooth on devices using these HIDs,
I've tested the following HIDs / devices:
BCM2E74: Jumper ezPad mini 3
BCM2E83: Acer Iconia Tab8 w1-810
BCM2E90: Meegopad T08
BCM2EAA: Chuwi Vi8 plus (CWI519)
The reporter of Red Hat bugzilla 1554835 has tested:
BCM2E84: Lenovo Yoga2
The reporter of kernel bugzilla 274481 has tested:
BCM2E38: Toshiba Encore
Note the Lenovo Yoga2 and Toshiba Encore also needs the earlier patch to
treat all Interrupt ACPI resources as active low.
Cc: stable@vger.kernel.org
Buglink: https://bugzilla.kernel.org/attachment.cgi?id=274481
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1554835
Reported-and-tested-by: Robert R. Howell <rhowell@uwyo.edu>
Reported-and-tested-by: Christian Herzog <daduke@daduke.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Older devices with a serdev attached bcm bt hci, use an Interrupt ACPI
resource to describe the IRQ (rather then a GpioInt resource).
These device seem to all claim the IRQ is active-high and seem to all need
a DMI quirk to treat it as active-low. Instead simply always assume that
Interrupt resource specified IRQs are always active-low.
This fixes the bt device not being able to wake the host from runtime-
suspend on the: Asus T100TAM, Asus T200TA, Lenovo Yoga2 and the Toshiba
Encore, without the need to add 4 new DMI quirks for these models.
This also allows us to remove 2 DMI quirks for the Asus T100TA and Asus
T100CHI series. Likely the 2 remaining quirks can also be removed but I
could not find a DSDT of these devices to verify this.
Cc: stable@vger.kernel.org
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=198953
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1554835
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The struct hcill_cmd to create an skb with a single u8 is pointless. So
just use skb_put_u8 instead.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The variable "payload" will eventually be set to an appropriate pointer
a bit later. Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The local variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case the shutdown GPIO is not wired up, it is impossible to reset the
Bluetooth controller to its original state. This include the initial
default baud rate which leads to issues when reloading the module or
when something unexpected happens. To avoid any kind of runtime
deadlocks, stick with the initial default baud rate.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some GPIO controller drivers request sleepable context and so can't
be accessed from IRQ context. Using gpiod_set/get_value accessors
with such controller leads to a kernel warning since they are
reserved for atomic context (according to the documentation).
Use the postfixed _cansleep version instead, indicating that context
is safe for sleeping if necessary. Note that this is the case here
since we never toggle the gpio neither from IRQ nor from a spinlocked
section.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The linkage between the bluetooth driver and the wireless
driver is not defined properly, leading to build problems
such as:
warning: (BT_HCIRSI) selects RSI_COEX which has unmet direct dependencies (NETDEVICES && WLAN && WLAN_VENDOR_RSI && BT_HCIRSI && RSI_91X)
drivers/net/wireless/rsi/rsi_91x_main.o: In function `rsi_read_pkt':
(.text+0x205): undefined reference to `rsi_bt_ops'
As the dependency is actually the reverse (RSI_91X uses
the BT_RSI driver, not the other way round), this changes
the dependency to match, and enables the bluetooth driver
from the RSI_COEX symbol.
Fixes: 38aa4da504 ("Bluetooth: btrsi: add new rsi bluetooth driver")
Acked-by; Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJatkBHAAoJEG4XJFUm622bKuwH/1cPOfTDDd/kFdRSht0rkj0J
PJ+OxdlbnPuXU7R9juDo5r3WeNoyiXvsdKNYGchn9XIEq2BN1jzOzcE7FYs1IwKs
UPZ6gUgF4+wD5eL1tmiWd+P8CSMVVYAdUGE+CjXOdUT08s5NsIm4Uv86ry/nm7gI
DkrkdlRjqDb6Dx8M35kX9AguR1QHz2KmOu2htPomHzDONrD99z8FaqZQHg4oyNAX
yIvidDcDRYmMoHfkifJiuuUxnRgD935tM6QECYjGKXLnCDb9KklCaabe77lAH39M
EGI7Z6teZrvv5IozpGgPnUjr+hjgoiXxfQmFyXOZAmuSDHbxudYMfOd7KtQ18W0=
=ySDb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The IRQ output of the bcm bt-device is really a level IRQ signal, which
signals a logical high as long as the device's buffer contains data. Since
the draining in the buffer is done in the tty driver, we cannot (easily)
wait in a threaded interrupt handler for the draining, after which the
IRQ should go low again.
So instead we treat the IRQ as an edge interrupt. This opens the window
for a theoretical race where we wakeup, read some data and then autosuspend
*before* the IRQ has gone (logical) low, followed by the device just at
that moment receiving more data, causing the IRQ to stay high and we never
see an edge.
Since we call pm_runtime_mark_last_busy() on every received byte, there
should be plenty time for the IRQ to go (logical) low before we ever
suspend, so this should never happen, but after commit 43fff76834
("Bluetooth: hci_bcm: Streamline runtime PM code"), which has been reverted
since, this was actually happening causing the device to get stuck in
runtime suspend.
The bcm bt-device actually has a workaround for this, if we set the
pulsed_host_wake flag in the sleep parameters, then the device monitors
if the host is draining the buffer and if not then after a timeout the
device will pulse the IRQ line, causing us to see an edge, fixing the
stuck in suspend condition.
This commit sets the pulsed_host_wake flag to fix the (mostly theoretical)
race caused by us treating the IRQ as an edge IRQ.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit 43fff76834 ("Bluetooth: hci_bcm: Streamline runtime
PM code"). The commit msg for this commit states "No functional change
intended.", but replacing:
pm_runtime_get();
pm_runtime_mark_last_busy();
pm_runtime_put_autosuspend();
with:
pm_request_resume();
Does result in a functional change, pm_request_resume() only calls
pm_runtime_mark_last_busy() if the device was suspended before the call.
This results in the following happening:
1) Device is runtime suspended
2) Device drives host_wake IRQ logically high as it starts receiving data
3) bcm_host_wake() gets called, causes the device to runtime-resume,
current time gets marked as last_busy time
4) After 5 seconds the autosuspend timer expires and the dev autosuspends
as no one has been calling pm_runtime_mark_last_busy(), the device was
resumed during those 5 seconds, so all the pm_request_resume() calls
while receiving data and/or bcm_host_wake() calls were nops
5) If 4) happens while the device has (just received) data in its buffer to
be read by the host the IRQ line is *already* / still logically high
when we autosuspend and since we use an edge triggered IRQ, the IRQ
will never trigger, causing the device to get stuck in suspend
Therefor this commit has to be reverted, so that we avoid the device
getting stuck in suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Redpine bluetooth driver is a thin driver which depends on
'rsi_91x' driver for transmitting and receiving packets
to/from device. It creates hci interface when attach() is
called from 'rsi_91x' module.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1fdb926974 ("Bluetooth: btusb: Use DMI matching for QCA
reset_resume quirking"), added the Lenovo Yoga 920 to the
btusb_needs_reset_resume_table.
Testing has shown that this is a false positive and the problems where
caused by issues with the initial fix: commit fd865802c6 ("Bluetooth:
btusb: fix QCA Rome suspend/resume"), which has already been reverted.
So the QCA Rome BT in the Yoga 920 does not need a reset-resume quirk at
all and this commit removes it from the btusb_needs_reset_resume_table.
Note that after this commit the btusb_needs_reset_resume_table is now
empty. It is kept around on purpose, since this whole series of commits
started for a reason and there are actually broken platforms around,
which need to be added to it.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Fixes: 1fdb926974 ("Bluetooth: btusb: Use DMI matching for QCA ...")
Cc: stable@vger.kernel.org
Cc: Brian Norris <briannorris@chromium.org>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kevin Fenzi <kevin@scrye.com>
Suggested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the devicetree binding the shutdown and device wake
GPIOs are optional. Since commit 3e81a4ca51 ("Bluetooth: hci_bcm:
Mandate presence of shutdown and device wake GPIO") this driver
won't probe anymore on Raspberry Pi 3 and Zero W (no device wake GPIO
connected). So fix this regression by reverting this commit partially.
Fixes: 3e81a4ca51 ("Bluetooth: hci_bcm: Mandate presence of shutdown and device wake GPIO")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-02-15
Here's the first bluetooth-next pull request targetting the 4.17 kernel
release.
- Fixes & cleanups to Atheros and Marvell drivers
- Support for two new Realtek controllers
- Support for new Intel Bluetooth controller
- Fix for supporting multiple slave-role Bluetooth LE connections
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
