desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds specific power-off method for Buffalo Linkstation Mini
board. The board has a hardware switch which should be monitored from
userspace. When the switch is in OFF position the board should be rebooted
and U-Boot will start in an idle mode and wait for the user to move the
power switch back to ON position.
Signed-off-by: Alexey Kopytko <alexey@kopytko.ru>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds support for Buffalo Linkstation Mini board.
Signed-off-by: Alexey Kopytko <alexey@kopytko.ru>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch provides standard GPIO LED control
for the ED Mini V2, with software blinking only
(CPLD hardware blinking capability is not used).
This patch also provides status of the power
button as a standard GPIO input event.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The RD88F6183AP-GE is an access point reference design for the
88F6183 SoC, with a 88E6161 six-port gigabit ethernet switch with
five PHYs (providing 1 WAN and 4 LAN ports and an interface to the
CPU), and a mini-PCIe slot for a wireless card.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Orion-1-90 (88F6183) is another member of the Orion SoC family,
which has a 16 bit DDR2 interface, one x1 PCIe port (configurable as
Root Complex or Endpoint), one 10/100/1000 ethernet interface, one
USB 2.0 port with PHY, one SPDIF/I2S interface, one SDIO interface,
one TWSI interface, two UARTs, one SPI interface, a NAND controller,
a crypto engine, and a 4-channel DMA engine.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch adds support for the Buffalo Terastation Pro II/Live.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch adds support for the LaCie Ethernet Disk mini V2.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Signed-off-by: Christopher Moore <moore@free.fr>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Currently, orion5x uses a hardcoded timer tick rate of 166 MHz, but
the actual timer tick rate varies between different members of the SoC
family (and can vary based on strap pin settings).
This patch prepares for runtime determination of the timer tick rate.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Wire up the ethernet port's error interrupt so that the
mv643xx_eth driver can sleep for SMI event completion instead of
having to busy-wait for it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Currently, there are two different fields in the
mv643xx_eth_platform_data struct that together describe the PHY
address -- one field (phy_addr) has the address of the PHY, but if
that address is zero, a second field (force_phy_addr) needs to be
set to distinguish the actual address zero from a zero due to not
having filled in the PHY address explicitly (which should mean
'use the default PHY address').
If we are a bit smarter about the encoding of the phy_addr field,
we can avoid the need for a second field -- this patch does that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Register UART1 on QNAP TS-209 and TS-409 because the PIC controller
is connected to it. This fixes a regression from 2.6.26.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The lm75 driver was recently converted to the new-style binding,
so now it can be loaded from the DNS-323 support code.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Tested-by: Tobias Poschwatta <tp@fonz.de>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Flash needs to be set up before we can try to read the MAC address
from there.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Kurobox Pro crashes when any of the PCI controller registers
are accessed. This patch adds a function to the Orion PCI handling
code that board support code can call to disable enumerating the
PCI bus entirely, and makes the Kurobox Pro PCI-related init code
call this function.
Signed-off-by: Per Andersson <avtobiff@gmail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The reset button on the QNAP TS-409 is available through gpio.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Use key codes for the buttons on the TS-209/TS-409 that make more
sense than the current values.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Export the four red SATA LEDs on the QNAP TS-409 that are connected
through gpio. Since the boot loader apparently sets the SATA LEDs 2-4
to red and the SATA LED can only be red or green (but not both),
exporting the red SATA LEDs (which automatically turns them off upon
boot) makes the green SATA presence/activity indication visible.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
On D0 5281 SoCs, we need to disable the wait-for-interrupt
instruction due to an erratum.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mv643xx_eth hardware has a provision for polling the PHY's
MII management registers to obtain the (R)(G)MII interface speed
(10/100/1000) and duplex (half/full) and pause (off/symmetric)
settings to use to talk to the PHY.
The driver currently does not make use of this feature. Instead,
whenever there is a link status change event, it reads the current
link parameters from the PHY, and programs those parameters into
the mv643xx_eth MAC by hand.
This patch switches the mv643xx_eth driver to letting the MAC
auto-determine the (R)(G)MII link parameters by PHY polling, if there
is a PHY present. For PHYless ports (when e.g. the (R)(G)MII
interface is connected to a hardware switch), we keep hardcoding the
MII interface parameters.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The HP mv2120 has several LEDs that are controlled through gpio.
Export the health LED, the red SATA LEDs as well as two gpios
that control the brightness of _all_ LEDs to userland. The
Ethernet and power LEDs can't be controlled through gpio and the
blue SATA LEDs are handled via the SATA driver.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds support for the Marvell Orion-VoIP RD-88F5181L-FXO
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds support for the Marvell Orion-VoIP RD2-88F5181L-GE
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Cardbus connector does not have an IDSEL signal, and Cardbus
cards are always the intended target of configuration transactions
on their local PCI bus. This means that if the Orion's PCI bus
signals are hooked up to a Cardbus slot, the same set of PCI
functions will will appear 31 times, for each of the PCI device
IDs 1-31 (ID 0 is the host bridge).
This patch adds a function to the Orion PCI handling code that board
support code can call to enable Cardbus mode. When Cardbus mode is
enabled, configuration transactions on the PCI local bus are only
allowed to PCI IDs 0 (host bridge) and 1 (cardbus device).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
In some cases, compilation of the tsx09 common file was failing due
to an incomplete list of includes.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
After Jean Delvare's change "i2c: Convert most new-style drivers
to use module aliasing" (3760f73671),
loading rtc-xxx from platform code fails. Update mv2120-setup.c so
that the driver is loaded correctly.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Kurobox Pro/Linkstation Pro devices use a microcontroller connected
to UART1. As most of the communication with this microcontroller is
done from userland (power button detection, fan speed ...), the setup
file has to make UART1 available from userland.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch adds support for the Maxtor Shared Storage II hardware.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch implements the communication with the microcontroller on the
Kurobox Pro and Linkstation Pro/Live boards. This is allowing to send
the commands needed to power-off the board correctly.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The mv643xx_eth platform data field ->force_phy_addr only needs
to be set if the passed-in ->phy_addr field is zero (to distinguish
the case of not having specified a phy address
(force_phy_addr = 0) from the case where a phy address of zero needs
to be used (force_phy_addr = 1.))
Also, the ->force_phy_addr field will hopefully disappear in a
future mv643xx_eth reorganisation.
Therefore, this patch deletes the ->force_phy_addr field initialiser
from all Orion board code.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
If all PCI devices are working as expected, the error printks in the
various implementations of ->map_irq() doesn't really provide any
useful info. And if something is not working as expected, turning
on pci=debug gives you more useful information than the printk calls
in ->map_irq(), since the former also tells you which devices _did_
get IRQs successfully assigned. Therefore, delete these printks
entirely.
Spotted by Russell King.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Instead of having board code poke directly into the MPP configuration
registers, and separately calling orion5x_gpio_set_valid_pins() to
indicate which MPP pins can be used as GPIO pins, introduce a helper
function for configuring the roles of each of the MPP pins, and have
that helper function handle gpio validity internally.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
It makes no sense to do PCIe WA window setup in the individual
board support files while the decision whether or not to use the
PCIe WA access method is made in a different place, in the PCIe
support code.
This patch moves the configuration of a PCIe WA window from the
individual Orion board support files to the central Orion PCIe
support code.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
This patch moves initialisation of EHCI/I2C/UART platform devices
from the common orion5x_init() into the board support code.
The rationale behind this is that only the board support code knows
whether certain peripherals have been brought out on the board, and
not initialising peripherals that haven't been brought out is
desirable for example:
- to reduce user confusion (e.g. seeing both 'eth0' and 'eth1'
appear while there is only one ethernet port on the board); and
- to allow for future power savings (peripherals that have not
been brought out can be clock gated off entirely).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
The DRAM base address and size fields in the CPU's MBUS bridge have
64KiB granularity, instead of the currently used 16MiB. Since all
of the currently supported MBUS peripherals support 64KiB granularity
as well, this patch changes the Orion address map code to stop
rounding base addresses down and sizes up to multiples of 16MiB.
Found by Ke Wei <kewei@marvell.com>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Currently, Orion window setup uses hardcoded window indexes for each
of the boot/cs0/cs1/cs2/PCIe WA windows. The static window allocation
used can clash if board support code will ever attempt to configure
both a dev2 and a PCIe WA window, as both of those use CPU mbus window
#7 at present.
This patch keeps track of the last used window, and opens subsequently
requested windows sequentially, starting from 4. (Windows 0-3 are used
as MEM/IO windows for the PCI/PCIe buses.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
More cosmetic cleanup:
- Replace 8-space indents by proper tab indents.
- In structure initialisers, use a trailing comma for every member.
- Collapse "},\n{" in structure initialiers to "}, {".
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Whereas most Orion 5x machine support code would initialise the PCI
subsystem with nr_controllers in their struct hw_pci set to 2, the
DNS323 and Kurobox Pro machine support code had nr_controllers set
to 1.
This was presumably done because on those two machines, the PCI(-X)
controller (nr == 1) isn't used, requiring initialisation of only
the PCIe controller (nr == 0.) However, not initialising the PCI(-X)
controller on boards that don't use it leads to a situation where
both the PCIe and the PCI(-X) controller think that their root bus is
zero, and it messes up IRQ assignment.
This patch changes the DNS323 and Kurobox Pro support code to always
use nr_controllers == 2.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch cleans up Orion's addr-map.c a bit after all peripheral
window programming code has been moved out into the relevant drivers.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Pass the Orion TCLK tick rate into the ethernet driver.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Make the Orion 5x platform code use the mbus window handling code
that's in the mv643xx_eth driver, instead of programming the GigE
block's mbus window registers by hand.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Move mv643xx_eth's static state (ethernet register block base address
and MII management interface spinlock) into a struct hanging off the
shared platform device. This is necessary to support chips that
contain multiple mv643xx_eth silicon blocks.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Unify a couple more spellings of "PCIe" ("PCI-E", "PCIE".)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
End addresses in 'struct resource' are inclusive -- fix the common
orion5x code to pass in the proper end addresses when instantiating
the two on-chip EHCI controllers.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The current orion5x board ->map_irq() routines check whether a
given bus number lives on the PCIe controller by comparing it with
the PCIe controller's primary bus number. This doesn't work in
case there are multiple buses in the PCIe domain, i.e. if there
exists a PCIe bridge on the primary PCIe bus.
This patch adds a helper function (orion5x_pci_map_irq()) that
returns the IRQ number for the given PCI device if that device has
a hard-wired IRQ, or -1 otherwise, and makes each board's
->map_irq() function use this helper function.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Buffalo Linkstation Pro/Live is the same hardware as the
Kurobox Pro but without the NAND flash. This patch adds a
second MACHINE_START macro to the Kurobox setup file to minimise
code duplication.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bootloader on ts209 Orion boards doesn't configure the right
ethernet MAC address into the GigE unit on boot. The only way to
get the MAC address is by parsing it from the 'NAS Config' flash
partition, which is an ext2 partition that contains a file which
holds the MAC address in plain text (format "xx:xx:xx:xx:xx:xx\n")
-- this patch does that.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Cc: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do a global s/orion/orion5x/ of the Orion 5x-specific bits (i.e.
not the plat-orion bits.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
