The 6 bytes length of the tries_buf string in ata_eh_link_report() is
too short and results in a gcc compilation warning with W-!:
drivers/ata/libata-eh.c: In function ‘ata_eh_link_report’:
drivers/ata/libata-eh.c:2371:59: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 4 [-Wformat-truncation=]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~
drivers/ata/libata-eh.c:2371:56: note: directive argument in the range [-2147483648, 4]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~
drivers/ata/libata-eh.c:2371:17: note: ‘snprintf’ output between 4 and 14 bytes into a destination of size 6
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2372 | ap->eh_tries);
| ~~~~~~~~~~~~~
Avoid this warning by increasing the string size to 16B.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
The introduction of a device link to create a consumer/supplier
relationship between the scsi device of an ATA device and the ATA port
of that ATA device fixes the ordering of system suspend and resume
operations. For suspend, the scsi device is suspended first and the ata
port after it. This is fine as this allows the synchronize cache and
START STOP UNIT commands issued by the scsi disk driver to be executed
before the ata port is disabled.
For resume operations, the ata port is resumed first, followed
by the scsi device. This allows having the request queue of the scsi
device to be unfrozen after the ata port resume is scheduled in EH,
thus avoiding to see new requests prematurely issued to the ATA device.
Since libata sets manage_system_start_stop to 1, the scsi disk resume
operation also results in issuing a START STOP UNIT command to the
device being resumed so that the device exits standby power mode.
However, restoring the ATA device to the active power mode must be
synchronized with libata EH processing of the port resume operation to
avoid either 1) seeing the start stop unit command being received too
early when the port is not yet resumed and ready to accept commands, or
after the port resume process issues commands such as IDENTIFY to
revalidate the device. In this last case, the risk is that the device
revalidation fails with timeout errors as the drive is still spun down.
Commit 0a85890559 ("ata,scsi: do not issue START STOP UNIT on resume")
disabled issuing the START STOP UNIT command to avoid issues with it.
But this is incorrect as transitioning a device to the active power
mode from the standby power mode set on suspend requires a media access
command. The IDENTIFY, READ LOG and SET FEATURES commands executed in
libata EH context triggered by the ata port resume operation may thus
fail.
Fix these synchronization issues is by handling a device power mode
transitions for system suspend and resume directly in libata EH context,
without relying on the scsi disk driver management triggered with the
manage_system_start_stop flag.
To do this, the following libata helper functions are introduced:
1) ata_dev_power_set_standby():
This function issues a STANDBY IMMEDIATE command to transitiom a device
to the standby power mode. For HDDs, this spins down the disks. This
function applies only to ATA and ZAC devices and does nothing otherwise.
This function also does nothing for devices that have the
ATA_FLAG_NO_POWEROFF_SPINDOWN or ATA_FLAG_NO_HIBERNATE_SPINDOWN flag
set.
For suspend, call ata_dev_power_set_standby() in
ata_eh_handle_port_suspend() before the port is disabled and frozen.
ata_eh_unload() is also modified to transition all enabled devices to
the standby power mode when the system is shutdown or devices removed.
2) ata_dev_power_set_active() and
This function applies to ATA or ZAC devices and issues a VERIFY command
for 1 sector at LBA 0 to transition the device to the active power mode.
For HDDs, since this function will complete only once the disk spin up.
Its execution uses the same timeouts as for reset, to give the drive
enough time to complete spinup without triggering a command timeout.
For resume, call ata_dev_power_set_active() in
ata_eh_revalidate_and_attach() after the port has been enabled and
before any other command is issued to the device.
With these changes, the manage_system_start_stop and no_start_on_resume
scsi device flags do not need to be set in ata_scsi_dev_config(). The
flag manage_runtime_start_stop is still set to allow the sd driver to
spinup/spindown a disk through the sd runtime operations.
Fixes: 0a85890559 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
commit 1e641060c4 ("libata: clear eh_info on reset completion") added
a workaround that broke the retry mechanism in ATA EH.
Tejun himself suggested to remove this workaround when it was identified
to cause additional problems:
https://lore.kernel.org/linux-ide/20110426135027.GI878@htj.dyndns.org/
He even said:
"Hmm... it seems I wasn't thinking straight when I added that work around."
https://lore.kernel.org/linux-ide/20110426155229.GM878@htj.dyndns.org/
While removing the workaround solved the issue, however, the workaround was
kept to avoid "spurious hotplug events during reset", and instead another
workaround was added on top of the existing workaround in commit
8c56cacc72 ("libata: fix unexpectedly frozen port after ata_eh_reset()").
Because these IRQs happened when the port was frozen, we know that they
were actually a side effect of PxIS and IS.IPS(x) not being cleared before
the COMRESET. This is now done in commit 94152042eaa9 ("ata: libahci: clear
pending interrupt status"), so these workarounds can now be removed.
Since commit 1e641060c4 ("libata: clear eh_info on reset completion") has
now been reverted, the ATA EH retry mechanism is functional again, so there
is once again no need to thaw the port more than once in ata_eh_reset().
This reverts "the workaround on top of the workaround" introduced in commit
8c56cacc72 ("libata: fix unexpectedly frozen port after ata_eh_reset()").
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
ata_scsi_port_error_handler() starts off by clearing ATA_PFLAG_EH_PENDING,
before calling ap->ops->error_handler() (without holding the ap->lock).
If an error IRQ is received while ap->ops->error_handler() is running,
the irq handler will set ATA_PFLAG_EH_PENDING.
Once ap->ops->error_handler() returns, ata_scsi_port_error_handler()
checks if ATA_PFLAG_EH_PENDING is set, and if it is, another iteration
of ATA EH is performed.
The problem is that ATA_PFLAG_EH_PENDING is not only cleared by
ata_scsi_port_error_handler(), it is also cleared by ata_eh_reset().
ata_eh_reset() is called by ap->ops->error_handler(). This additional
clearing done by ata_eh_reset() breaks the whole retry logic in
ata_scsi_port_error_handler(). Thus, if an error IRQ is received while
ap->ops->error_handler() is running, the port will currently remain
frozen and will never get re-enabled.
The additional clearing in ata_eh_reset() was introduced in commit
1e641060c4 ("libata: clear eh_info on reset completion").
Looking at the original error report:
https://marc.info/?l=linux-ide&m=124765325828495&w=2
We can see the following happening:
[ 1.074659] ata3: XXX port freeze
[ 1.074700] ata3: XXX hardresetting link, stopping engine
[ 1.074746] ata3: XXX flipping SControl
[ 1.411471] ata3: XXX irq_stat=400040 CONN|PHY
[ 1.411475] ata3: XXX port freeze
[ 1.420049] ata3: XXX starting engine
[ 1.420096] ata3: XXX rc=0, class=1
[ 1.420142] ata3: XXX clearing IRQs for thawing
[ 1.420188] ata3: XXX port thawed
[ 1.420234] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
We are not supposed to be able to receive an error IRQ while the port is
frozen (PxIE is set to 0, i.e. all IRQs for the port are disabled).
AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) states:
"Each bit location can be thought of as reporting a '1' if the virtual
"interrupt line" for that port is indicating it wishes to generate an
interrupt. That is, if a port has one or more interrupt status bit set,
and the enables for those status bits are set, then this bit shall be set."
Additionally, AHCI state P:ComInit clearly shows that the state machine
will only jump to P:ComInitSetIS (which sets IS.IPS(x) to '1'), if PxIE.PCE
is set to '1'. In our case, PxIE is set to 0, so IS.IPS(x) won't get set.
So IS.IPS(x) only gets set if PxIS and PxIE is set.
AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) also states:
"The bits in this register are read/write clear. It is set by the level of
the virtual interrupt line being a set, and cleared by a write of '1' from
the software."
So if IS.IPS(x) is set, you need to explicitly clear it by writing a 1 to
IS.IPS(x) for that port.
Since PxIE is cleared, the only way to get an interrupt while the port is
frozen, is if IS.IPS(x) is set, and the only way IS.IPS(x) can be set when
the port is frozen, is if it was set before the port was frozen.
However, since commit 737dd811a3 ("ata: libahci: clear pending interrupt
status"), we clear both PxIS and IS.IPS(x) after freezing the port, but
before the COMRESET, so the problem that commit 1e641060c4 ("libata:
clear eh_info on reset completion") fixed can no longer happen.
Thus, revert commit 1e641060c4 ("libata: clear eh_info on reset
completion"), so that the retry logic in ata_scsi_port_error_handler()
works once again. (The retry logic is still needed, since we can still
get an error IRQ _after_ the port has been thawed, but before
ata_scsi_port_error_handler() takes the ap->lock in order to check
if ATA_PFLAG_EH_PENDING is set.)
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
With commit 65a15d6560 ("scsi: ipr: Remove SATA support") all
libata drivers now have the error_handler() callback provided,
so we can stop checking for non-existing error_handler callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[niklas: fixed review comments, rebased, solved conflicts during rebase,
fixed bug that unconditionally dumped all QCs, removed the now unused
function ata_dump_status(), removed the now unreachable failure paths in
atapi_qc_complete(), removed the non-EH function to request ATAPI sense]
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
ata_eh_reset_timeouts[] stores 'unsigned long' timeouts in ms, while
ata_eh_reset() passes these values to ata_deadline() that takes just
'unsigned int timeout_msecs' parameter. Change the reset timeout table
element's type to 'unsigned int' -- all timeouts fit into 'unsigned int'
but we have to change ULONG_MAX to UINT_MAX...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Updates to the usual drivers (ufs, pm80xx, libata-scsi, smartpqi,
lpfc, qla2xxx). We have a couple of major core changes impacting
other systems: Command Duration Limits, which spills into block and
ATA and block level Persistent Reservation Operations, which touches
block, nvme, target and dm (both of which are added with merge commits
containing a cover letter explaining what's going on).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZJ19cSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfZpAQCQBuWR
ELcOhsaG5KzO6xLWcH8mjsOoxffKvazZjTKXlAD5ATEv7++E250oKS3t+yfjae5I
Lc195MlDju85ItUQgfk=
=U9ik
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, pm80xx, libata-scsi, smartpqi,
lpfc, qla2xxx).
We have a couple of major core changes impacting other systems:
- Command Duration Limits, which spills into block and ATA
- block level Persistent Reservation Operations, which touches block,
nvme, target and dm
Both of these are added with merge commits containing a cover letter
explaining what's going on"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (187 commits)
scsi: core: Improve warning message in scsi_device_block()
scsi: core: Replace scsi_target_block() with scsi_block_targets()
scsi: core: Don't wait for quiesce in scsi_device_block()
scsi: core: Don't wait for quiesce in scsi_stop_queue()
scsi: core: Merge scsi_internal_device_block() and device_block()
scsi: sg: Increase number of devices
scsi: bsg: Increase number of devices
scsi: qla2xxx: Remove unused nvme_ls_waitq wait queue
scsi: ufs: ufs-pci: Add support for Intel Arrow Lake
scsi: sd: sd_zbc: Use PAGE_SECTORS_SHIFT
scsi: ufs: wb: Add explicit flush_threshold sysfs attribute
scsi: ufs: ufs-qcom: Switch to the new ICE API
scsi: ufs: dt-bindings: qcom: Add ICE phandle
scsi: ufs: ufs-mediatek: Set UFSHCD_QUIRK_MCQ_BROKEN_RTC quirk
scsi: ufs: ufs-mediatek: Set UFSHCD_QUIRK_MCQ_BROKEN_INTR quirk
scsi: ufs: core: Add host quirk UFSHCD_QUIRK_MCQ_BROKEN_RTC
scsi: ufs: core: Add host quirk UFSHCD_QUIRK_MCQ_BROKEN_INTR
scsi: ufs: core: Remove dedicated hwq for dev command
scsi: ufs: core: mcq: Fix the incorrect OCS value for the device command
scsi: ufs: dt-bindings: samsung,exynos: Drop unneeded quotes
...
- Add support for the .remove_new callback to the ata_platform code to
simplify device removal interface (Uwe).
- Code simplification in ata_dev_revalidate() (Yahu)
- Fix code indentation and coding style in the pata_parport protocol
modules to avoid warnings from static code analyzers (me)
- Clarify ata_eh_qc_retry() behavior with better comments (Niklas)
- Simplify and improve ata_change_queue_depth() behavior to have a
consistent behavior between libsas managed devices and libata managed
devices (e.g. AHCI connected devices) (me).
- Cleanup libata-scsi and libata-eh code to use the ata_ncq_enabled()
and ata_ncq_supported() helpers instead of open coding flags tests
(me)
- Cleanup ahci_reset_controller() code (me).
- Change the pata_octeon_cf and sata_svw drivers to use
of_property_read_reg() to simplify the code (Rob, me).
- Remove unnecessary include files from ahci_octeon driver (me)
- Modify the DesignWare ahci dt bindings to add support for the
Rockchip RK3588 AHCI (Sebastian).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCZJourwAKCRDdoc3SxdoY
dv43AQDzAFY0/0sjvqltGC31wRzzh/vEQFWsYt89Q4csMr4QgAEAkLO1gquH5/Wt
sxnCLh1WdFqbyNy6xsw+CXrfeREGDgo=
=IzEr
-----END PGP SIGNATURE-----
Merge tag 'ata-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata updates from Damien Le Moal:
- Add support for the .remove_new callback to the ata_platform code to
simplify device removal interface (Uwe)
- Code simplification in ata_dev_revalidate() (Yahu)
- Fix code indentation and coding style in the pata_parport protocol
modules to avoid warnings from static code analyzers (me)
- Clarify ata_eh_qc_retry() behavior with better comments (Niklas)
- Simplify and improve ata_change_queue_depth() behavior to have a
consistent behavior between libsas managed devices and libata managed
devices (e.g. AHCI connected devices) (me)
- Cleanup libata-scsi and libata-eh code to use the ata_ncq_enabled()
and ata_ncq_supported() helpers instead of open coding flags tests
(me)
- Cleanup ahci_reset_controller() code (me)
- Change the pata_octeon_cf and sata_svw drivers to use
of_property_read_reg() to simplify the code (Rob, me)
- Remove unnecessary include files from ahci_octeon driver (me)
- Modify the DesignWare ahci dt bindings to add support for the
Rockchip RK3588 AHCI (Sebastian)
* tag 'ata-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (29 commits)
dt-bindings: phy: rockchip: rk3588 has two reset lines
dt-bindings: ata: dwc-ahci: add Rockchip RK3588
dt-bindings: ata: dwc-ahci: add PHY clocks
ata: ahci_octeon: Remove unnecessary include
ata: pata_octeon_cf: Add missing header include
ata: ahci: Cleanup ahci_reset_controller()
ata: Use of_property_read_reg() to parse "reg"
ata: libata-scsi: Use ata_ncq_supported in ata_scsi_dev_config()
ata: libata-eh: Use ata_ncq_enabled() in ata_eh_speed_down()
ata: libata-sata: Improve ata_change_queue_depth()
ata: libata-sata: Simplify ata_change_queue_depth()
ata: libata-eh: Clarify ata_eh_qc_retry() behavior at call site
ata: pata_parport: Fix on26 module code indentation and style
ata: pata_parport: Fix on20 module code indentation and style
ata: pata_parport: Fix ktti module code indentation and style
ata: pata_parport: Fix kbic module code indentation and style
ata: pata_parport: Fix friq module code indentation and style
ata: pata_parport: Fix fit3 module code indentation and style
ata: pata_parport: Fix fit2 module code indentation and style
ata: pata_parport: Fix epia module code indentation and style
...
When an ATA port is resumed from sleep, the port is reset and a power
management request issued to libata EH to reset the port and rescanning
the device(s) attached to the port. Device rescanning is done by
scheduling an ata_scsi_dev_rescan() work, which will execute
scsi_rescan_device().
However, scsi_rescan_device() takes the generic device lock, which is
also taken by dpm_resume() when the SCSI device is resumed as well. If
a device rescan execution starts before the completion of the SCSI
device resume, the rcu locking used to refresh the cached VPD pages of
the device, combined with the generic device locking from
scsi_rescan_device() and from dpm_resume() can cause a deadlock.
Avoid this situation by changing struct ata_port scsi_rescan_task to be
a delayed work instead of a simple work_struct. ata_scsi_dev_rescan() is
modified to check if the SCSI device associated with the ATA device that
must be rescanned is not suspended. If the SCSI device is still
suspended, ata_scsi_dev_rescan() returns early and reschedule itself for
execution after an arbitrary delay of 5ms.
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: Joe Breuer <linux-kernel@jmbreuer.net>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217530
Fixes: a19a93e4c6 ("scsi: core: pm: Rely on the device driver core for async power management")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Joe Breuer <linux-kernel@jmbreuer.net>
In ata_eh_speed_down(), instead of hard-coding the test on the device
flags to detect if NCQ is supported and enabled, use ata_ncq_enabled().
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
While the function documentation for ata_eh_qc_retry() is clear,
from simply reading the single function that calls ata_eh_qc_retry(),
it is not clear that ata_eh_qc_retry() might not retry the command.
Add a comment in the single function that calls ata_eh_qc_retry() to
clarify the behavior.
[Damien] Added curly braces to "if () else" with multi-line comment.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
A CDL timeout for policy 0xF is defined as a NCQ error, just with a CDL
specific sk/asc/ascq in the sense data. Therefore, the existing code in
libata does not need to be modified to handle a policy 0xF CDL timeout.
For Command Duration Limits policy 0xD:
The device shall complete the command without error with the additional
sense code set to DATA CURRENTLY UNAVAILABLE.
Since a CDL timeout for policy 0xD is not an error, we cannot use the NCQ
Command Error log (10h).
Instead, we need to read the Sense Data for Successful NCQ Commands log
(0Fh).
In the success case, just like in the error case, we cannot simply read a
log page from the interrupt handler itself, since reading a log page
involves sending a READ LOG DMA EXT or READ LOG EXT command.
Therefore, we add a new EH action ATA_EH_GET_SUCCESS_SENSE. When a command
completes without error, and when the ATA_SENSE bit is set, this new action
is set as pending, and EH is scheduled.
This way, similar to the NCQ error case, the log page will be read from EH
context.
An alternative would have been to add a new kthread or workqueue to handle
this. However, extending EH can be done with minimal changes and avoids the
need to synchronize a new kthread/workqueue with EH.
Co-developed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-20-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, ata_eh_request_sense() unconditionally sets the scsicmd->result
to SAM_STAT_CHECK_CONDITION.
For Command Duration Limits policy 0xD:
The device shall complete the command without error (SAM_STAT_GOOD) with
the additional sense code set to DATA CURRENTLY UNAVAILABLE.
It is perfectly fine to have sense data for a command that returned
completion without error.
In order to support for CDL policy 0xD, we have to remove this assumption
that having sense data means that the command failed
(SAM_STAT_CHECK_CONDITION).
Change ata_eh_request_sense() to not set SAM_STAT_CHECK_CONDITION, and
instead move the setting of SAM_STAT_CHECK_CONDITION to the single caller
that wants SAM_STAT_CHECK_CONDITION set, that way ata_eh_request_sense()
can be reused in a follow-up patch that adds support for CDL policy 0xD.
The only caller of ata_eh_request_sense() is protected by: if (!(qc->flags
& ATA_QCFLAG_SENSE_VALID)), so we can remove this duplicated check from
ata_eh_request_sense() itself.
Additionally, ata_eh_request_sense() is only called from
ata_eh_analyze_tf(), which is only called when iteratating the QCs using
ata_qc_for_each_raw(), which does not include the internal tag, so cmd can
never be NULL (all non-internal commands have qc->scsicmd set), so remove
the !cmd check as well.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Link: https://lore.kernel.org/r/20230511011356.227789-14-nks@flawful.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The name ATA_QCFLAG_FAILED is misleading since it does not mean that a
QC completed in error, or that it didn't complete at all. It means that
libata decided to schedule EH for the QC, so the QC is now owned by the
libata error handler (EH).
The normal execution path is responsible for not accessing a QC owned
by EH. libata core enforces the rule by returning NULL from
ata_qc_from_tag() for QCs owned by EH.
It is quite easy to mistake that a QC marked with ATA_QCFLAG_FAILED was
an error. However, a QC that was actually an error is instead indicated
by having qc->err_mask set. E.g. when we have a NCQ error, we abort all
QCs, which currently will mark all QCs as ATA_QCFLAG_FAILED. However, it
will only be a single QC that is an error (i.e. has qc->err_mask set).
Rename ATA_QCFLAG_FAILED to ATA_QCFLAG_EH to more clearly highlight that
this flag simply means that a QC is now owned by EH. This new name will
not mislead to think that the QC was an error (which is instead
indicated by having qc->err_mask set).
This also makes it more obvious that the EH code skips all QCs that do
not have ATA_QCFLAG_EH set (rather than ATA_QCFLAG_FAILED), since the EH
code should simply only care about QCs that are owned by EH itself.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
If ap->ops->error_handler is NULL just return. This patch also
fixes some comment style issue.
Signed-off-by: Wenchao Hao <haowenchao@huawei.com>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
A NCQ error means that the device has aborted processing of all active
commands.
To get the single NCQ command that caused the NCQ error, host software has
to read the NCQ error log, which also takes the device out of error state.
When the device encounters a NCQ error, we receive an error interrupt from
the HBA, and call ata_do_link_abort() to mark all outstanding commands on
the link as ATA_QCFLAG_FAILED (which means that these commands are owned
by libata EH), and then call ata_qc_complete() on them.
ata_qc_complete() will call fill_result_tf() for all commands marked as
ATA_QCFLAG_FAILED.
The taskfile is simply the latest status/error as seen from the device's
perspective. The taskfile will have ATA_ERR set in the status field and
ATA_ABORTED set in the error field.
When we fill the current taskfile values for all outstanding commands,
that means that qc->result_tf will have ATA_ERR set for all commands
owned by libata EH.
When ata_eh_link_autopsy() later analyzes all commands owned by libata EH,
it will call ata_eh_analyze_tf(), which will check if qc->result_tf has
ATA_ERR set, if it does, it will set qc->err_mask (which marks the command
as an error).
When ata_eh_finish() later calls __ata_qc_complete() on all commands owned
by libata EH, it will call qc->complete_fn() (ata_scsi_qc_complete()),
ata_scsi_qc_complete() will call ata_gen_ata_sense() to generate sense
data if qc->err_mask is set.
This means that we will generate sense data for commands that should not
have any sense data set. Having sense data set for the non-failed commands
will cause SCSI to finish these commands instead of retrying them.
While this incorrect behavior has existed for a long time, this first
became a problem once we started reading the correct taskfile register in
commit 4ba09d2026 ("ata: libahci: read correct status and error field
for NCQ commands").
Before this commit, NCQ commands would read the taskfile values received
from the last non-NCQ command completion, which most likely did not have
ATA_ERR set, since the last non-NCQ command was most likely not an error.
Fix this by changing ata_eh_analyze_ncq_error() to mark all non-failed
commands as ATA_QCFLAG_RETRY, and change the loop in ata_eh_link_autopsy()
to skip commands marked as ATA_QCFLAG_RETRY.
While at it, make sure that we clear ATA_ERR and any error bits for all
commands except the actual command that caused the NCQ error, so that no
other libata code will be able to misinterpret these commands as errors.
Fixes: 4ba09d2026 ("ata: libahci: read correct status and error field for NCQ commands")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Clean up the code by making use of the newly introduced
ata_port_is_frozen() helper function.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Currently, the sense data reporting feature set is enabled for all ATA
devices which supports the feature set (ata_id_has_sense_reporting()),
see ata_dev_config_sense_reporting().
However, even if sense data reporting is enabled, and the device
indicates that sense data is available, the sense data is only fetched
for ATA ZAC devices. For regular ATA devices, the available sense data
is never fetched, it is simply ignored. Instead, libata will use the
ERROR + STATUS fields and map them to a very generic and reduced set
of sense data, see ata_gen_ata_sense() and ata_to_sense_error().
When sense data reporting was first implemented, regular ATA devices
did fetch the sense data from the device. However, this was restricted
to only ATA ZAC devices in commit ca156e006a ("libata: don't request
sense data on !ZAC ATA devices").
With recent changes related to sense data and NCQ autosense, we want
to, once again, fetch the sense data for all ATA devices supporting
sense reporting.
ata_gen_ata_sense() should only be used for devices that don't support
the sense data reporting feature set.
hopefully the features will be more robust this time around.
It is not just ZAC, many new ATA features, e.g. Command Duration
Limits, relies on working NCQ autosense and sense data. Therefore,
it is not really an option to avoid fetching the sense data forever.
If we encounter a device that is misbehaving because the sense data is
actually fetched, then that device should be quirked such that it
never enables the sense data reporting feature set in the first place,
since such a device is obviously not compliant with the specification.
The order in which we will try to add sense data to a scsi_cmnd:
1) NCQ autosense (if supported) - ata_eh_analyze_ncq_error()
2) REQUEST SENSE DATA EXT (if supported) - ata_eh_request_sense()
3) error + status field translation - ata_gen_ata_sense(), called
by ata_scsi_qc_complete() if neither 1) or 2) is supported.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
While this shouldn't be needed if all devices that claim that they
support NCQ autosense (ata_id_has_ncq_autosense()) and/or the sense
data reporting feature (ata_id_has_sense_reporting()), actually
supported those features.
However, there might be some old ATA devices that either have these
bits set, even when they don't support those features, or they simply
return malformed data when using those features.
These devices should be quirked, but in order to try to minimize the
impact for the users of these such devices, it was suggested by Damien
Le Moal that it might be a good idea to sanity check the sense data
received from the device. If the sense data looks bogus, then the
sense data is never added to the scsi_cmnd command.
Introduce a new function, ata_scsi_sense_is_valid(), and use it in all
places where sense data is received from the device.
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
ata_eh_request_sense() returns early when flag ATA_QCFLAG_SENSE_VALID is
set. However, since the call to ata_eh_request_sense() is guarded by a
ATA_SENSE bit conditional, the logical conclusion for the reader is that
all checks are performed at the call site.
Highlight the fact that the sense data will not be fetched if flag
ATA_QCFLAG_SENSE_VALID is already set by adding an additional check to
the existing guarding conditional. No functional change.
Additionally, add a comment explaining that ata_eh_analyze_tf() will
only fetch the sense data if:
-It was a non-NCQ command that failed, or
-It was a NCQ command that failed, but the sense data was not included
in the NCQ command error log (i.e. NCQ autosense is not supported).
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
* Print the timeout value for internal command failures due to a
timeout (from Tomas).
* Improve parameter names in ata_dev_set_feature() to clarify this
function use (from Niklas).
* Improve the ahci driver low power mode setting initialization to allow
more flexibility for the user (from Rafael).
* Several patches to remove redundant variables in libata-core,
libata-eh and the pata_macio driver and to fix typos in comments (from
Jinpeng, Shaomin, Ye).
* Some code simplifications and macro renaming (for clarity) in various
functions of libata-core (from me).
* Add a missing check for a potential failure of sata_scr_read() in
sata_print_link_status() (from Li).
* Cleanup of libata Kconfig PATA_PLATFORM and PATA_OF_PLATFORM options
(from Lukas).
* Cleanups of ata dt-bindings and improvements of libahci_platform, ahci
and libahci code (from Serge)
* New driver for Synopsys AHCI SATA controllers, based of the generic
ahci code (from Serge). One compilation warning fix is added for this
driver (from me).
* Several fixes to macros used to discover a drive capabilities to be
consistent with the ACS specifications (from Niklas).
* A couple of simplifcations to some libata functions, removing
unnecessary arguments (from Niklas).
* An improvements to libata-eh code to avoid unnecessary link reset when
revalidating a drive after a failed command. In practice, this extra,
unneeded reset, reset does not cause any arm beyond slightly slowing
down error recovery (from Niklas).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCYz0asgAKCRDdoc3SxdoY
drHoAQCJhb6MuQHzbN/wR5cTGAfWXQJWBJx2mJr7oKJCrB34PwD/RzphcsuaXDta
kwbTGlpitegByZTDKt9eMRLWmKgyngw=
=CnJj
-----END PGP SIGNATURE-----
Merge tag 'ata-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata updates from Damien Le Moal:
- Print the timeout value for internal command failures due to a
timeout (from Tomas)
- Improve parameter names in ata_dev_set_feature() to clarify this
function use (from Niklas)
- Improve the ahci driver low power mode setting initialization to
allow more flexibility for the user (from Rafael)
- Several patches to remove redundant variables in libata-core,
libata-eh and the pata_macio driver and to fix typos in comments
(from Jinpeng, Shaomin, Ye)
- Some code simplifications and macro renaming (for clarity) in various
functions of libata-core (from me)
- Add a missing check for a potential failure of sata_scr_read() in
sata_print_link_status() (from Li)
- Cleanup of libata Kconfig PATA_PLATFORM and PATA_OF_PLATFORM options
(from Lukas)
- Cleanups of ata dt-bindings and improvements of libahci_platform,
ahci and libahci code (from Serge)
- New driver for Synopsys AHCI SATA controllers, based of the generic
ahci code (from Serge). One compilation warning fix is added for this
driver (from me)
- Several fixes to macros used to discover a drive capabilities to be
consistent with the ACS specifications (from Niklas)
- A couple of simplifcations to some libata functions, removing
unnecessary arguments (from Niklas)
- An improvements to libata-eh code to avoid unnecessary link reset
when revalidating a drive after a failed command. In practice, this
extra, unneeded reset, reset does not cause any arm beyond slightly
slowing down error recovery (from Niklas)
* tag 'ata-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (45 commits)
ata: libata-eh: avoid needless hard reset when revalidating link
ata: libata: drop superfluous ata_eh_analyze_tf() parameter
ata: libata: drop superfluous ata_eh_request_sense() parameter
ata: fix ata_id_has_dipm()
ata: fix ata_id_has_ncq_autosense()
ata: fix ata_id_has_devslp()
ata: fix ata_id_sense_reporting_enabled() and ata_id_has_sense_reporting()
ata: libata-eh: Remove the unneeded result variable
ata: ahci_st: Enable compile test
ata: ahci_st: Fix compilation warning
MAINTAINERS: Add maintainers for DWC AHCI SATA driver
ata: ahci-dwc: Add Baikal-T1 AHCI SATA interface support
ata: ahci-dwc: Add platform-specific quirks support
dt-bindings: ata: ahci: Add Baikal-T1 AHCI SATA controller DT schema
ata: ahci: Add DWC AHCI SATA controller support
ata: libahci_platform: Add function returning a clock-handle by id
dt-bindings: ata: ahci: Add DWC AHCI SATA controller DT schema
ata: ahci: Introduce firmware-specific caps initialization
ata: ahci: Convert __ahci_port_base to accepting hpriv as arguments
ata: libahci: Don't read AHCI version twice in the save-config method
...
Performing a revalidation on a AHCI controller supporting LPM,
while using a lpm mode of e.g. med_power_with_dip (hipm + dipm) or
medium_power (hipm), will currently always lead to a hard reset.
The expected behavior is that a hard reset is only performed when
revalidate fails, because the properties of the drive has changed.
A revalidate performed after e.g. a NCQ error, or such a simple thing
as disabling write-caching (hdparm -W 0 /dev/sda), should succeed on
the first try (and should therefore not cause the link to be reset).
This unwarranted hard reset happens because ata_phys_link_offline()
returns true for a link that is in deep sleep. Thus the call to
ata_phys_link_offline() in ata_eh_revalidate_and_attach() will cause
the revalidation to fail, which causes ata_eh_handle_dev_fail() to be
called, which will set ehc->i.action |= ATA_EH_RESET, such that the
link is reset before retrying revalidation.
When the link is reset, the link is reestablished, so when
ata_eh_revalidate_and_attach() is called the second time, directly
after the link has been reset, ata_phys_link_offline() will return
false, and the revalidation will succeed.
Looking at "8.3.1.3 HBA Initiated" in the AHCI 1.3.1 specification,
it is clear the when host software writes a new command to memory,
by setting a bit in the PxCI/PxSACT HBA port registers, the HBA will
automatically bring back the link before sending out the Command FIS.
However, simply reading a SCR (like ata_phys_link_offline() does),
will not cause the HBA to automatically bring back the link.
As long as hipm is enabled, the HBA will put an idle link into deep
sleep. Avoid this needless hard reset on revalidation by temporarily
disabling hipm, by setting the LPM mode to ATA_LPM_MAX_POWER.
After revalidation is complete, ata_eh_recover() will restore the link
policy by setting the LPM mode to ap->target_lpm_policy.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The parameter can easily be derived from struct ata_queued_cmd.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The parameter can easily be derived from struct ata_queued_cmd.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Return the value ata_port_abort() directly instead of storing it in
another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Add the missing command name for ATA_CMD_NCQ_NON_DATA to
ata_get_cmd_name().
Fixes: 661ce1f0c4 ("libata/libsas: Define ATA_CMD_NCQ_NON_DATA")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
ata_internal_cmd_timeout() returns *unsigned long* timeout in ms, however
ata_exec_internal_sg() passes that timeout to msecs_to_jiffies() that takes
just *unsigned int*. Change ata_internal_cmd_timeout()'s result type to
*unsigned int* as well, also updating the *struct* ata_eh_cmd_timeout_ent
and the command timeout tables -- all timeouts fit into *unsigned int* but
we have to change ULONG_MAX to UINT_MAX...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
ata_eh_nr_in_flight() counts the # of the active tagged commands and
thus cannot return a negative value but the result type is nevertheless
int. Switching it to unsigned int (along with the local variables
receiving the function's result) helps avoiding the sign extension
instructions when comparing with or assigning to unsigned long
ata_port::fastdrain_cnt and thus results in a more compact 64-bit
code.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
[Damien]
Fixed commit message.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Add the explicit error and status register fields to 'struct ata_taskfile'
using the anonymous *union*s ('struct ide_taskfile' had that for ages!) and
update the libata taskfile code accordingly. There should be no object code
changes resulting from that...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Since the commit c05e6ff035 ("libata-acpi: implement
and use ata_acpi_init_gtm()") ata_acpi_on_suspend() just returns 0, so
its call from ata_eh_handle_port_suspend() doesn't make sense anymore.
Remove the function completely, at last...
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Callers are already protected by ata_dev_print_info(), so no need
to have an additional configuration parameter here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Rename ata_get_cmd_descrip() to ata_get_cmd_name() and simplify
it to return "unknown" instead of NULL.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
To follow the flow of control we should be using tracepoints, as
they will tie in with the actual I/O flow and deliver a better
overview about what it happening.
This patch adds tracepoints for hard reset, soft reset, and postreset
and adds them in the libata-eh control flow.
With that we can drop the reset DPRINTK calls in the various drivers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Some ATA drives are very slow to respond to READ_LOG_EXT and
READ_LOG_DMA_EXT commands issued from ata_dev_configure() when the
device is revalidated right after resuming a system or inserting the
ATA adapter driver (e.g. ahci). The default 5s timeout
(ATA_EH_CMD_DFL_TIMEOUT) used for these commands is too short, causing
errors during the device configuration. Ex:
...
ata9: SATA max UDMA/133 abar m524288@0x9d200000 port 0x9d200400 irq 209
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: ATA-9: XXX XXXXXXXXXXXXXXX, XXXXXXXX, max UDMA/133
ata9.00: qc timeout (cmd 0x2f)
ata9.00: Read log page 0x00 failed, Emask 0x4
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: NCQ Send/Recv Log not supported
ata9.00: Read log page 0x08 failed, Emask 0x40
ata9.00: 27344764928 sectors, multi 16: LBA48 NCQ (depth 32), AA
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: ATA Identify Device Log not supported
ata9.00: failed to set xfermode (err_mask=0x40)
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: configured for UDMA/133
...
The timeout error causes a soft reset of the drive link, followed in
most cases by a successful revalidation as that give enough time to the
drive to become fully ready to quickly process the read log commands.
However, in some cases, this also fails resulting in the device being
dropped.
Fix this by using adding the ata_eh_revalidate_timeouts entries for the
READ_LOG_EXT and READ_LOG_DMA_EXT commands. This defines a timeout
increased to 15s, retriable one time.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Prepare for removal of the request pointer by using scsi_cmd_to_rq()
instead. This patch does not change any functionality.
Link: https://lore.kernel.org/r/20210809230355.8186-8-bvanassche@acm.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, target, tcmu,
smartpqi, lpfc, zfcp, qla2xxx, mpt3sas, pm80xx). The major core
change is using a sbitmap instead of an atomic for queue tracking.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYInvqCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYh2AP0SgqqL
WYZRT2oiyBOKD28v+ceOSiXvgjPlqABwVMC0BAEAn29/wNCxyvzZ1k/b0iPJ4M+S
klkSxLzXKQLzJBgdK5w=
=p5B/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, target, tcmu,
smartpqi, lpfc, zfcp, qla2xxx, mpt3sas, pm80xx).
The major core change is using a sbitmap instead of an atomic for
queue tracking"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (412 commits)
scsi: target: tcm_fc: Fix a kernel-doc header
scsi: target: Shorten ALUA error messages
scsi: target: Fix two format specifiers
scsi: target: Compare explicitly with SAM_STAT_GOOD
scsi: sd: Introduce a new local variable in sd_check_events()
scsi: dc395x: Open-code status_byte(u8) calls
scsi: 53c700: Open-code status_byte(u8) calls
scsi: smartpqi: Remove unused functions
scsi: qla4xxx: Remove an unused function
scsi: myrs: Remove unused functions
scsi: myrb: Remove unused functions
scsi: mpt3sas: Fix two kernel-doc headers
scsi: fcoe: Suppress a compiler warning
scsi: libfc: Fix a format specifier
scsi: aacraid: Remove an unused function
scsi: core: Introduce enum scsi_disposition
scsi: core: Modify the scsi_send_eh_cmnd() return value for the SDEV_BLOCK case
scsi: core: Rename scsi_softirq_done() into scsi_complete()
scsi: core: Remove an incorrect comment
scsi: core: Make the scsi_alloc_sgtables() documentation more accurate
...
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Improve readability of the code in the SCSI core by introducing an
enumeration type for the values used internally that decide how to continue
processing a SCSI command. The eh_*_handler return values have not been
changed because that would involve modifying all SCSI drivers.
The output of the following command has been inspected to verify that no
out-of-range values are assigned to a variable of type enum
scsi_disposition:
KCFLAGS=-Wassign-enum make CC=clang W=1 drivers/scsi/
Link: https://lore.kernel.org/r/20210415220826.29438-6-bvanassche@acm.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some functions have different names between their prototypes
and the kernel-doc markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* move ata_eh_analyze_ncq_error() and ata_eh_read_log_10h() to
libata-sata.c
* add static inline for ata_eh_analyze_ncq_error() for
CONFIG_SATA_HOST=n case (link->sactive is non-zero only if
NCQ commands are actually queued so empty function body is
sufficient)
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
16164 18 0 16182 3f36 drivers/ata/libata-eh.o
after:
15446 18 0 15464 3c68 drivers/ata/libata-eh.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add !IS_ENABLED(CONFIG_SATA_HOST) to ata_eh_set_lpm() to allow
compiler to optimize out the function for non-SATA configs (for
PATA hosts "ap && !ap->ops->set_lpm" condition is always true so
it's sufficient for the function to return zero).
Code size savings on m68k arch using (modified) atari_defconfig:
text data bss dec hex filename
before:
17353 18 0 17371 43db drivers/ata/libata-eh.o
after:
16607 18 0 16625 40f1 drivers/ata/libata-eh.o
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move EXPORT_SYMBOL_GPL()s close to exported code like it is
done in other kernel subsystems. As a nice side effect this
results in the removal of few ifdefs.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In commit 7634ccd2da ("libata: maintainership update") from 2018
Jens has officially taken over libata maintainership from Tejun so
remove stale information from core libata code.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ZAC support added sense data requesting on error for both ZAC and ATA
devices. This seems to cause erratic error handling behaviors on some
SSDs where the device reports sense data availability and then
delivers the wrong content making EH take the wrong actions. The
failure mode was sporadic on a LITE-ON ssd and couldn't be reliably
reproduced.
There is no value in requesting sense data from non-ZAC ATA devices
while there's a significant risk of introducing EH misbehaviors which
are difficult to reproduce and fix. Let's do the sense data dancing
only for ZAC devices.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Masato Suzuki <masato.suzuki@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program see
the file copying if not write to the free software foundation 675
mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 52 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.342335923@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is nothing it could synchronize against, so don't go through
the pains of acquiring the lock.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
