Currently, when CONFIG_VIRT_CPU_ACCOUNTING is enabled, we use the
PURR register for measuring the user and system time used by
processes, as well as other related times such as hardirq and
softirq times. This turns out to be quite confusing for users
because it means that a program will often be measured as taking
less time when run on a multi-threaded processor (SMT2 or SMT4 mode)
than it does when run on a single-threaded processor (ST mode), even
though the program takes longer to finish. The discrepancy is
accounted for as stolen time, which is also confusing, particularly
when there are no other partitions running.
This changes the accounting to use the timebase instead, meaning that
the reported user and system times are the actual number of real-time
seconds that the program was executing on the processor thread,
regardless of which SMT mode the processor is in. Thus a program will
generally show greater user and system times when run on a
multi-threaded processor than on a single-threaded processor.
On pSeries systems on POWER5 or later processors, we measure the
stolen time (time when this partition wasn't running) using the
hypervisor dispatch trace log. We check for new entries in the
log on every entry from user mode and on every transition from
kernel process context to soft or hard IRQ context (i.e. when
account_system_vtime() gets called). So that we can correctly
distinguish time stolen from user time and time stolen from system
time, without having to check the log on every exit to user mode,
we store separate timestamps for exit to user mode and entry from
user mode.
On systems that have a SPURR (POWER6 and POWER7), we read the SPURR
in account_system_vtime() (as before), and then apportion the SPURR
ticks since the last time we read it between scaled user time and
scaled system time according to the relative proportions of user
time and system time over the same interval. This avoids having to
read the SPURR on every kernel entry and exit. On systems that have
PURR but not SPURR (i.e., POWER5), we do the same using the PURR
rather than the SPURR.
This disables the DTL user interface in /sys/debug/kernel/powerpc/dtl
for now since it conflicts with the use of the dispatch trace log
by the time accounting code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This arranges for the lppaca structs for most cpus to be dynamically
allocated in the same manner as the paca structs. If we don't include
support for legacy iSeries, only the first lppaca is statically
allocated; the rest are dynamically allocated. If we include legacy
iSeries support, then we statically allocate the first 64 lppaca
structs, since the iSeries hypervisor requires that the lppaca
structs be present in the data section of the kernel image, but
legacy iSeries supports at most 64 cpus.
With CONFIG_NR_CPUS, the kernel image size for a typical pSeries config
went from:
text data bss dec hex filename
9524478 4734564 8469944 22728986 15ad11a ../test-1024/vmlinux
to:
text data bss dec hex filename
9524482 3751508 8469944 21745934 14bd10e ../test-1024/vmlinux
a reduction of 983052 bytes overall.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we have the lppaca structs as a simple array of NR_CPUS
entries, taking up space in the data section of the kernel image.
In future we would like to allocate them dynamically, so this
abstracts out the accesses to the array, making it easier to
change how we locate the lppaca for a given cpu in future.
Specifically, lppaca[cpu] changes to lppaca_of(cpu).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simple cleanup by moving arch_sd_sibling_asym_packing from process.c to
smp.c to save an #ifdef CONFIG_SMP
No functionality change.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a check for the stack canary when we oops, similar to x86. This should make
it clear that we overran our stack:
Unable to handle kernel paging request for data at address 0x24652f63700ac689
Faulting instruction address: 0xc000000000063d24
Thread overran stack, or stack corrupted
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The POWER architecture does not require stcx to check that it is operating
on the same address as the larx. This means it is possible for an
an exception handler to execute a larx, get a reservation, decide
not to do the stcx and then return back with an active reservation. If the
interrupted code was in the middle of a larx/stcx sequence the stcx could
incorrectly succeed.
All recent POWER CPUs check the address before letting the stcx succeed
so we can create a CPU feature and nop it out. As Ben suggested, we can
only do this in our syscall path because there is a remote possibility
some kernel code gets interrupted by an exception that ends up operating
on the same cacheline.
Thanks to Paul Mackerras and Derek Williams for the idea.
To test this I used a very simple null syscall (actually getppid) testcase
at http://ozlabs.org/~anton/junkcode/null_syscall.c
I tested against 2.6.35-git10 with the following changes against the
pseries_defconfig:
CONFIG_VIRT_CPU_ACCOUNTING=n
CONFIG_AUDIT=n
CONFIG_PPC_4K_PAGES=n
CONFIG_PPC_64K_PAGES=y
CONFIG_FORCE_MAX_ZONEORDER=9
CONFIG_PPC_SUBPAGE_PROT=n
CONFIG_FUNCTION_TRACER=n
CONFIG_FUNCTION_GRAPH_TRACER=n
CONFIG_IRQSOFF_TRACER=n
CONFIG_STACK_TRACER=n
to remove the overhead of virtual CPU accounting, syscall auditing and
the ftrace mcount tracers. 64kB pages were enabled to minimise TLB misses.
POWER6: +8.2%
POWER7: +7.0%
Another suggestion was to use a larx to something in the L1 instead of a stcx.
This was almost as fast as removing the larx on POWER6, but only 3.5% faster
on POWER7. We can use this to speed up the reservation clear in our
exception exit code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the equivalent of csum_and_copy_from_user for the receive side so we
can copy and checksum in one pass. It is modelled on the generic checksum
routine.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use the same core loop as the new csum_partial, adding in the
stores and exception handling code. To keep things simple we do all the
exception fixup in csum_and_copy_from_user. This wrapper function is
modelled on the generic checksum code and is careful to always calculate
a complete checksum even if we only copied part of the data to userspace.
To test this I forced checksumming on over loopback and ran socklib (a
simple TCP benchmark). On a POWER6 575 throughput improved by 19% with
this patch. If I forced both the sender and receiver onto the same cpu
(with the hope of shifting the benchmark from being cache bandwidth limited
to cpu limited), adding this patch improved performance by 55%
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The main loop of csum_partial runs very slowly on recent POWER CPUs. After some
analysis on both POWER6 and POWER7 I came up with routine below. First we get
the source aligned to a double word, ignoring any odd alignment to keep things
simple. Then we do 64 bytes at a time, with an entry and exit limb of a further
64 bytes. On both POWER6 and POWER7 this should be as fast as we can go since
we are limited by the latency of the adde instructions.
To test this I forced checksumming on over loopback and ran socklib (a
simple TCP benchmark). On a POWER6 575 throughput improved by 11% with
this patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The dlpar code can cause a deadlock to occur when making the RTAS
configure-connector call. This occurs because we make kmalloc calls,
which can block, while parsing the rtas_data_buf and holding the
rtas_data_buf_lock. This an cause issues if someone else attempts
to grab the rtas_data_bug_lock.
This patch alleviates this issue by copying the contents of the rtas_data_buf
to a local buffer before parsing. This allows us to only hold the
rtas_data_buf_lock around the RTAS configure-connector calls.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is needed for proper PCI-E support on P1021 SoCs.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a call to of_node_put in the error handling code following a call to
of_find_compatible_node.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
of_node_put(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The function of_iomap returns the result of calling ioremap, so iounmap
should be called on the result in the error handling code, as done in the
normal exit of the function.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1;
identifier l;
statement S;
@@
*x = of_iomap(...);
... when != iounmap(x)
when != if (...) { ... iounmap(x); ... }
when != E = x
when any
(
if (x == NULL) S
|
if (...) {
... when != iounmap(x)
when != if (...) { ... iounmap(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
)
... when != x = E1
when any
iounmap(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fixes the following compile problem on E500 platforms:
arch/powerpc/sysdev/fsl_rio.c: In function 'fsl_rio_mcheck_exception':
arch/powerpc/sysdev/fsl_rio.c:248: error: 'MCSR_MASK' undeclared (first use in this function)
Also fixes the compile problem on non-E500 platforms.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/p1022_ds.c:22:23: error: linux/lmb.h: No such file or directory
arch/powerpc/platforms/85xx/p1022_ds.c: In function 'p1022_ds_setup_arch':
arch/powerpc/platforms/85xx/p1022_ds.c💯 error: implicit declaration of function 'memblock_end_of_DRAM'
arch/powerpc/platforms/85xx/p1022_ds.c: At top level:
arch/powerpc/platforms/85xx/p1022_ds.c:147: error: 'udbg_progress' undeclared here (not in a function)
make[2]: *** [arch/powerpc/platforms/85xx/p1022_ds.o] Error 1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 99d8238f berobbed the for_each loop of its iterator! Let's be
nice and give it back, so it compiles for us.
CC: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In f761622e59 we changed
early_setup_secondary so it's called using the proper kernel stack
rather than the emergency one.
Unfortunately, this stack pointer can't be used when translation is off
on PHYP as this stack pointer might be outside the RMO. This results in
the following on all non zero cpus:
cpu 0x1: Vector: 300 (Data Access) at [c00000001639fd10]
pc: 000000000001c50c
lr: 000000000000821c
sp: c00000001639ff90
msr: 8000000000001000
dar: c00000001639ffa0
dsisr: 42000000
current = 0xc000000016393540
paca = 0xc000000006e00200
pid = 0, comm = swapper
The original patch was only tested on bare metal system, so it never
caught this problem.
This changes __secondary_start so that we calculate the new stack
pointer but only start using it after we've called early_setup_secondary.
With this patch, the above problem goes away.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 0fe1ac48 ("powerpc/perf_event: Fix oops due to
perf_event_do_pending call") moved the call to perf_event_do_pending
in timer_interrupt() down so that it was after the irq_enter() call.
Unfortunately this moved it after the code that checks whether it
is time for the next decrementer clock event. The result is that
the call to perf_event_do_pending() won't happen until the next
decrementer clock event is due. This was pointed out by Milton
Miller.
This fixes it by moving the check for whether it's time for the
next decrementer clock event down to the point where we're about
to call the event handler, after we've called perf_event_do_pending.
This has the side effect that on old pre-Core99 Powermacs where we
use the ppc_n_lost_interrupts mechanism to replay interrupts, a
replayed interrupt will incur a little more latency since it will
now do the code from the irq_enter down to the irq_exit, that it
used to skip. However, these machines are now old and rare enough
that this doesn't matter. To make it clear that ppc_n_lost_interrupts
is only used on Powermacs, and to speed up the code slightly on
non-Powermac ppc32 machines, the code that tests ppc_n_lost_interrupts
is now conditional on CONFIG_PMAC as well as CONFIG_PPC32.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Call kexec purgatory code correctly. We were getting lucky before.
If you examine the powerpc 32bit kexec "purgatory" code you will
see it expects the following:
>From kexec-tools: purgatory/arch/ppc/v2wrap_32.S
-> calling convention:
-> r3 = physical number of this cpu (all cpus)
-> r4 = address of this chunk (master only)
As such, we need to set r3 to the current core, r4 happens to be
unused by purgatory at the moment but we go ahead and set it
here as well
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: work around VIA and NEC PHY packet reception bug
firewire: core: do not use del_timer_sync() in interrupt context
firewire: net: fix unicast reception RCODE in failure paths
firewire: sbp2: fix stall with "Unsolicited response"
firewire: sbp2: fix memory leak in sbp2_cancel_orbs or at send error
ieee1394: Adjust confusing if indentation
VIA VT6306, VIA VT6308, and NEC OrangeLink controllers do not write
packet event codes for received PHY packets (or perhaps write
evt_no_status, hard to tell). Work around it by overwriting the
packet's ACK by ack_complete, so that upper layers that listen to PHY
packet reception get to see these packets.
(Also tested: TI TSB82AA2, TI TSB43AB22/A, TI XIO2213A, Agere FW643,
JMicron JMB381 --- these do not exhibit this bug.)
Clemens proposed a quirks flag for that, IOW whitelist known misbehaving
controllers for this workaround. Though to me it seems harmless enough
to enable for all controllers.
The log_ar_at_event() debug log will continue to show the original
status from the DMA unit.
Reported-by: Clemens Ladisch <clemens@ladisch.de> (VT6308)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net/ipv4: Eliminate kstrdup memory leak
net/caif/cfrfml.c: use asm/unaligned.h
ax25: missplaced sock_put(sk)
qlge: reset the chip before freeing the buffers
l2tp: test for ethernet header in l2tp_eth_dev_recv()
tcp: select(writefds) don't hang up when a peer close connection
tcp: fix three tcp sysctls tuning
tcp: Combat per-cpu skew in orphan tests.
pxa168_eth: silence gcc warnings
pxa168_eth: update call to phy_mii_ioctl()
pxa168_eth: fix error handling in prope
pxa168_eth: remove unneeded null check
phylib: Fix race between returning phydev and calling adjust_link
caif-driver: add HAS_DMA dependency
3c59x: Fix deadlock between boomerang_interrupt and boomerang_start_tx
qlcnic: fix poll implementation
netxen: fix poll implementation
bridge: netfilter: fix a memory leak
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: bf52x/bf54x boards: drop unused nand page size
Blackfin: punt duplicate SPORT MMR defines
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S5PV310: Fix on Secondary CPU startup
ARM: S5PV310: Bug fix on uclk1 and sclk_pwm
ARM: S5PV310: Fix missed uart clocks
ARM: S5PV310: Should be clk_sclk_apll not clk_mout_apll
ARM: S5PV310: Fix on PLL setting for S5PV310
ARM: S5PV310: Add CMU block for S5PV310 Clock
ARM: S5PV310: Fix on typo irqs.h of S5PV310
ARM: S5PV310: Fix on default ZRELADDR of ARCH_S5PV310
ARM: S5PV310: Fix on GPIO base addresses
ARM: SAMSUNG: Fix on build warning regarding VMALLOC_END type
ARM: S5P: VMALLOC_END should be unsigned long
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
fsnotify: drop two useless bools in the fnsotify main loop
fsnotify: fix list walk order
fanotify: Return EPERM when a process is not privileged
fanotify: resize pid and reorder structure
fanotify: drop duplicate pr_debug statement
fanotify: flush outstanding perm requests on group destroy
fsnotify: fix ignored mask handling between inode and vfsmount marks
fanotify: add MAINTAINERS entry
fsnotify: reset used_inode and used_vfsmount on each pass
fanotify: do not dereference inode_mark when it is unset
* 'for-linus' of git://android.git.kernel.org/kernel/tegra:
arm: tegra: VMALLOC_END should be unsigned long
arm: tegra: fix compilation of board-harmony.c
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
vgaarb: Wrap vga_(get|put) in CONFIG_VGA_ARB
drm/radeon/kms: add missing scratch update in dp_detect
drm/modes: Fix CVT-R modeline generation
drm: fix regression in drm locking since BKL removal.
drm/radeon/kms: remove stray radeon_i2c_destroy
drm: mm: fix range restricted allocations
drm/nouveau: drop drm_global_mutex before sleeping in submission path
drm: export drm_global_mutex for drivers to use
drm/nv20: Don't use pushbuf calls on the original nv20.
drm/nouveau: Fix TMDS on some DCB1.5 boards.
drm/nouveau: Fix backlight control on PPC machines with an internal TMDS panel.
drm/nv30: Apply modesetting to the correct slave encoder
drm/nouveau: Use a helper function to match PCI device/subsystem IDs.
drm/nv50: add dcb type 14 to enum to prevent compiler complaint
* 'lguest' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: Odd Fixes
lguest: clean up warnings in demonstration launcher.
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3: PM: ensure IO wakeups are properly disabled
omap: Fix omap_4430sdp_defconfig for make oldconfig
omap: Use CONFIG_SMP for test_for_ipi and test_for_ltirq
omap: Fix sev instruction usage for multi-omap
OMAP3: Fix a cpu type check problem
omap3: id: fix 3630 rev detection
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix get_ticket_handler() error handling
ceph: don't BUG on ENOMEM during mds reconnect
ceph: ceph_mdsc_build_path() returns an ERR_PTR
ceph: Fix warnings
ceph: ceph_get_inode() returns an ERR_PTR
ceph: initialize fields on new dentry_infos
ceph: maintain i_head_snapc when any caps are dirty, not just for data
ceph: fix osd request lru adjustment when sending request
ceph: don't improperly set dir complete when holding EXCL cap
mm: exporting account_page_dirty
ceph: direct requests in snapped namespace based on nonsnap parent
ceph: queue cap snap writeback for realm children on snap update
ceph: include dirty xattrs state in snapped caps
ceph: fix xattr cap writeback
ceph: fix multiple mds session shutdown
* 'for-2.6.36' of git://linux-nfs.org/~bfields/linux:
nfsd: fix NULL dereference in nfsd_statfs()
nfsd4: fix downgrade/lock logic
nfsd4: typo fix in find_any_file
nfsd4: bad BUG() in preprocess_stateid_op
Fix a comma that got accidentally deleted from sys_osf_statfs() leading to the
following warning:
arch/alpha/kernel/osf_sys.c: In function 'SYSC_osf_statfs':
arch/alpha/kernel/osf_sys.c:255: error: syntax error before 'buffer'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stub out vm_get_page_prot() if there's no MMU.
This was added by commit 804af2cf6e ("[AGPGART] remove private page
protection map") and is used in commit c07fbfd17e ("fbmem: VM_IO set,
but not propagated") in the fbmem video driver, but the function doesn't
exist on NOMMU, resulting in an undefined symbol at link time.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Do not report error overflow as a separate error
MCE, AMD: Limit MCE decoding to current families for now
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata-sff: remove harmful BUG_ON from ata_bmdma_qc_issue
sata_mv: fix broken DSM/TRIM support (v2)
libata: be less of a drama queen on empty data commands
[libata] sata_dwc_460ex: signdness bug
ahci: add HFLAG_YES_FBS and apply it to 88SE9128
libata: remove no longer needed pata_winbond driver
pata_cmd64x: revert commit d62f5576
After several hours, kbuild tests hang with anon_vma_prepare() spinning on
a newly allocated anon_vma's lock - on a box with CONFIG_TREE_PREEMPT_RCU=y
(which makes this very much more likely, but it could happen without).
The ever-subtle page_lock_anon_vma() now needs a further twist: since
anon_vma_prepare() and anon_vma_fork() are liable to change the ->root
of a reused anon_vma structure at any moment, page_lock_anon_vma()
needs to check page_mapped() again before succeeding, otherwise
page_unlock_anon_vma() might address a different root->lock.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There were some new formats added in commit 15c0cee6c8 "ALSA: pcm:
Define G723 3-bit and 5-bit formats". That commit increased
SNDRV_PCM_FORMAT_LAST as well. My concern is that there are a couple
places which do:
for (i = 0; i < SNDRV_PCM_FORMAT_LAST; i++) {
if (dummy->pcm_hw.formats & (1ULL << i))
snd_iprintf(buffer, " %s", snd_pcm_format_name(i));
}
I haven't tested these but it looks like if "i" were equal to
SNDRV_PCM_FORMAT_G723_24 or higher then we might read past the end of
the array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The spinlock lock in sound_timer.c is used without initialization.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If hw error is ignored, status is updated with invalid info.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The string clone is only used as a temporary copy of the argument val
within the while loop, and so it should be freed before leaving the
function. The call to strsep, however, modifies clone, so a pointer to the
front of the string is kept in saved_clone, to make it possible to free it.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E;
identifier l;
statement S;
@@
*x= \(kasprintf\|kstrdup\)(...);
...
if (x == NULL) S
... when != kfree(x)
when != E = x
if (...) {
<... when != kfree(x)
* goto l;
...>
* return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fsnotify main loop has 2 bools which indicated if we processed the
inode or vfsmount mark in that particular pass through the loop. These
bool can we replaced with the inode_group and vfsmount_group variables
and actually make the code a little easier to understand.
Signed-off-by: Eric Paris <eparis@redhat.com>
Marks were stored on the inode and vfsmonut mark list in order from
highest memory address to lowest memory address. The code to walk those
lists thought they were in order from lowest to highest with
unpredictable results when trying to match up marks from each. It was
possible that extra events would be sent to userspace when inode
marks ignoring events wouldn't get matched with the vfsmount marks.
This problem only affected fanotify when using both vfsmount and inode
marks simultaneously.
Signed-off-by: Eric Paris <eparis@redhat.com>
