The older Allwinner SoCs (A10, A13, A10s and A20) all have the same SPI
controller.
Unfortunately, this SPI controller, even though quite similar, is significantly
different from the recently supported A31 SPI controller (different registers
offset, split/merged registers, etc.). Supporting both controllers in a single
driver would be unreasonable, hence the addition of a new driver.
Like its more recent counterpart, it supports DMA, but the driver only does PIO
until we have a dmaengine driver for this platform.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Qualcomm Universal Peripheral (QUP) core is an
AHB slave that provides a common data path (an output
FIFO and an input FIFO) for serial peripheral interface
(SPI) mini-core.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Freescale DSPI module will have two endianess in different platform,
but ARM is little endian. So when DSPI in big endian, core in little endian,
readl and writel can not adjust R/W register in this condition.
This patch will remove general readl/writel, and import regmap mechanism.
Data endian will be transfered in regmap APIs.
Documents: dspi add bool "big-endian" in dts node if DSPI module
work in big endian.
Signed-off-by: Chao Fu <b44548@freescale.com>
Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Document the clock properties required by the spi-atmel driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The Allwinner A31 has a new SPI controller IP compared to the older Allwinner
SoCs.
It supports DMA, but the driver only does PIO for now, and DMA will be
supported eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A respun version of the merges for the pull request previously sent with
a few additional fixes. The last two merges were fixed up by hand since
the branches have moved on and currently have the prior merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller.
- Fix duplicate device registration for ACPI.
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends).
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer.
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CbUw
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A respun version of the merges for the pull request previously sent
with a few additional fixes. The last two merges were fixed up by
hand since the branches have moved on and currently have the prior
merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller
- Fix duplicate device registration for ACPI
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends)
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers"
* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
spi: core: Fix transfer failure when master->transfer_one returns positive value
spi: Correct set_cs() documentation
spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
spi: Spelling s/finised/finished/
spi: sc18is602: Convert to use bits_per_word_mask
spi: Remove duplicate code to set default bits_per_word setting
spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
spi: clps711x: Add MODULE_ALIAS to support module auto-loading
spi: rspi: Add missing clk_disable() calls in error and cleanup paths
spi: rspi: Spelling s/transmition/transmission/
spi: rspi: Add support for specifying CPHA/CPOL
spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
spi: rspi: Add more QSPI register documentation
spi: rspi: Add more RSPI register documentation
spi: rspi: Remove dependency on DMAE for SHMOBILE
spi/s3c64xx: Correct indentation
spi: sh: Use spi_sh_clear_bit() instead of open-coded
spi: bitbang: Grammar s/make to make/to make/
spi: sh-hspi: Spelling s/recive/receive/
spi: core: Improve tx/rx_nbits check comments
...
These update binding information for ti qspi controller.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Update all the Tegra DT bindings to require the standard dmas/dma-names
properties rather than non-standard nvidia,dma-request-selector property.
This is a DT-ABI-incompatible change. It is the second of two changes
required for me to consider the Tegra DT bindings as stable, the other
being the previous conversion to the common reset bindings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Update all the Tegra DT bindings to require resets/reset-names properties
where the HW module has reset inputs. Remove any entries from clocks or
clock-names that were only required to identify reset inputs, rather than
referring to real clocks.
This is a DT-ABI-incompatible change. It is the first of two changes
required for me to consider the Tegra DT bindings as stable, the other
being conversion to the common DMA DT bindings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Many of the Tegra DT binding documents say nothing about the clocks or
clock-names properties, yet those are present and required in DT files.
This patch simply updates the documentation file to match the implicit
definition of the binding, based on real-world DT content.
All Tegra bindings that mention clocks are updated to have consistent
wording and formatting of the clock-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Commit 7431798490 (of_spi: add generic binding support to specify cs gpio)
introduced generic binding for gpio chip-select. The cs_gpio struct field,
however, is an internal implementation detail of the Linux SPI subsystem, and
should not be mentioned in the device tree binding documentation. Mention the
previously defined cs-gpios master node property instead.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
This binding shouldn't exist; Tegra20 has two forms of SPI controller
that are documented separately in nvidia,tegra20-sflash.txt and
nvidia,tegra20-slink.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Correct the SPI node compatible property items to match example code and
match current DTS usage.
Signed-off-by: Eric Witcher <ewitcher@mindspring.com>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support for loading the Renesas HSPI driver via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on various
platforms as support gets added. Some of the bigger changes are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for 4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1GuI
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on
various platforms as support gets added. Some of the bigger changes
are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for
4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
dts: Rename DW APB timer compatible strings
dts: Deprecate ALTR as a vendor prefix
of: add vendor prefix for Altera Corp.
ARM: at91/dt: sam9x5ek: add sound configuration
ARM: at91/dt: sam9x5ek: enable SSC
ARM: at91/dt: sam9x5ek: add WM8731 codec
ARM: at91/dt: sam9x5: add SSC DMA parameters
ARM: at91/dt: add at91rm9200 PQFP package version
ARM: at91: at91rm9200: set default mmc0 pinctrl-names
ARM: at91: at91sam9n12: correct pin number of gpio-key
ARM: at91: at91sam9n12: add qt1070 support
ARM: at91: at91sam9n12: add pinctrl of TWI
ARM: at91: Add PMU support for sama5d3
ARM: at91: at91sam9260: add missing pinctrl-names on mmc
ARM: tegra: configure power off for Dalmore
ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
ARM: dts: add sdio blocks to bcm28155-ap board
ARM: dts: align sdio numbers to HW definition
ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
ARM: sun7i: Add Allwinner A20 DTSI
...
spi: quad: fix the name of DT property in patch
The previous property name spi-tx-nbits and spi-rx-nbits looks not
human-readable. To make it consistent with other devices, using property
name spi-tx-bus-width and spi-rx-bus-width instead of the previous one
specify the number of data wires that spi controller will work in.
Add the specification in spi-bus.txt.
Signed-off-by: wangyuhang <wangyuhang2014@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Because most of the vendor prefixes are lower case, deprecate
the vendor prefix "ALTR" in place of "altr" for Altera Corp..
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
The patch add basic support for the quad spi controller.
QSPI is a kind of spi module that allows single,
dual and quad read access to external spi devices. The module
has a memory mapped interface which provide direct interface
for accessing data form external spi devices.
The patch will configure controller clocks, device control
register and for defining low level transfer apis which
will be used by the spi framework to transfer data to
the slave spi device(flash in this case).
Test details:
-------------
Tested this on dra7 board.
Test1: Ran mtd_stesstest for 40000 iterations.
- All iterations went through without failure.
Test2: Use mtd utilities:
- flash_erase to erase the flash device
- mtd_debug read to read data back.
- mtd_debug write to write to the data flash.
diff between the write and read data shows zero.
Acked-by: Felipe Balbi<balbi@ti.com>
Reviewed-by: Felipe Balbi<balbi@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the document for DSPI driver under
Documentation/devicetree/bindings/spi/.
Signed-off-by: Chao Fu <b44548@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
The binding definition is based on the generic DMA request binding
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle.
We normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time
we need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc cleanup
series because of interdependencies with timer drivers now moved out
of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes
for Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HWfp
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle. We
normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time we
need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc
cleanup series because of interdependencies with timer drivers now
moved out of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes for
Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10."
* tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
ARM: SPEAr: conditionalize SMP code
ARM: arch_timer: Silence debug preempt warnings
ARM: OMAP: remove unused variable
serial: amba-pl011: fix !CONFIG_DMA_ENGINE case
ata: arasan: remove the need for platform_data
ARM: at91/sama5d34ek.dts: remove not needed compatibility string
ARM: at91: dts: add MCI DMA support
ARM: at91: dts: add i2c dma support
ARM: at91: dts: set #dma-cells to the correct value
ARM: at91: suspend both memory controllers on at91sam9263
irqchip: armada-370-xp: slightly cleanup irq controller driver
irqchip: armada-370-xp: move IRQ handler to avoid forward declaration
irqchip: move IRQ driver for Armada 370/XP
ARM: mvebu: move L2 cache initialization in init_early()
devtree: add binding documentation for sp804
ARM: integrator-cp: convert use CLKSRC_OF for timer init
ARM: versatile: use OF init for sp804 timer
ARM: versatile: add versatile dtbs to dtbs target
...
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
This set of patches adds support for PWMs and SPI
controller present on DA850 and for SPI flash present on
DA850 EVM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=KZ+c
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.10/dt-2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt2
From Sekhar Nori:
v3.10 DT updates for DaVinci
This set of patches adds support for PWMs and SPI
controller present on DA850 and for SPI flash present on
DA850 EVM.
* tag 'davinci-for-v3.10/dt-2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM: davinci: da850: override mmc DT node device name
ARM: davinci: da850: add mmc DT entries
mmc: davinci_mmc: add DT support
ARM: davinci: da850: add tps6507x regulator DT data
ARM: regulator: add tps6507x device tree data
ARM: davinci: remove test for undefined Kconfig macro
ARM: davinci: mmc: derive version information from device name
ARM: davinci: da850: add ECAP & EHRPWM clock nodes
ARM: davinci: clk framework support for enable/disable functionality
Signed-off-by: Olof Johansson <olof@lixom.net>
With device core now able to setup the default pin configuration,
the pin configuration code based on the deprecated Samsung specific
gpio bindings is removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Add SPI driver for NVIDIA's Tegra114 SPI controller. This controller
is different than the older SoCs SPI controller in internal design as
well as register interface.
This driver supports the:
- non DMA based transfer for smaller transfer i.e. less than FIFO depth.
- APB DMA based transfer for larger transfer i.e. more than FIFO depth.
- Clock gating through runtime PM callbacks.
- registration through DT only.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds support for the mostly register-compatible SPICTRL cores from the
GRLIB VHDL IP core library from Aeroflex Gaisler. They are normally running on
SPARC. A different entry in of_fsl_spi_match matches this core and indicates a
different hardware type that is used to set up different function pointers and
special cases.
The GRLIB core operates in cpu mode. The number of bits per word might be
limited. There might be native chipselects selected via a slave select
register. These differences to the FSL type cores, if present, are indicated by
a capabilities register. Other register and function differences exists but are
not relevant to the driver.
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This makes the spi-fsl-spi driver usable in CPU mode outside of an FSL_SOC and
even an powerpc environment by moving CPM mode functionality to a separate file
that is only compiled and linked in an FSL_SOC environment and adding some
ifdefs to hide types and functions or provide alternatives.
For devicetree probing a "clock-frequency" property is used for clock frequency
instead of calls to FSL_SOC-specific functions.
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With the generic DMA device tree helper supported by mxs-dma driver,
client devices only need to call dma_request_slave_channel() for
requesting a DMA channel from dmaengine.
Since mxs is a DT only platform now, along with the changes, the non-DT
case handling in probe function also gets removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The BCM2835 contains two forms of SPI master controller (one known
simply as SPI0, and the other known as the "Universal SPI Master", in
the auxilliary block) and one form of SPI slave controller. This patch
adds support for the SPI0 controller.
This driver is taken from Chris Boot's repository at
git://github.com/bootc/linux.git rpi-linear
as of commit 6de2905 "spi-bcm2708: fix printf with spurious %s".
In the first SPI-related commit there, Chris wrote:
Thanks to csoutreach / A Robinson for his driver which I used as an
inspiration. You can find his version here:
http://piface.openlx.org.uk/raspberry-pi-spi-kernel-driver-available-for
Changes made during upstreaming:
* Renamed bcm2708 to bcm2835 as per upstream naming for this SoC.
* Removed support for brcm,realtime property.
* Increased transfer timeout to 30 seconds.
* Return IRQ_NONE from the IRQ handler if no interrupt was handled.
* Disable TA (Transfer Active) and clear FIFOs on a transfer timeout.
* Wrote device tree binding documentation.
* Request unnamed clock rather than "sys_pclk"; the DT will provide the
correct clock.
* Assume that tfr->speed_hz and tfr->bits_per_word are always set in
bcm2835_spi_start_transfer(), bcm2835_spi_transfer_one(), so no need
to check spi->speed_hz or tft->bits_per_word.
* Re-ordered probe() to remove the need for temporary variables.
* Call clk_disable_unprepare() rather than just clk_unprepare() on probe()
failure.
* Don't use devm_request_irq(), to ensure that the IRQ doesn't fire after
we've torn down the device, but not unhooked the IRQ.
* Moved probe()'s call to clk_prepare_enable() so we can be sure the clock
is enabled if the IRQ handler fires immediately.
* Remove redundant checks from bcm2835_spi_check_transfer() and
bcm2835_spi_setup().
* Re-ordered IRQ handler to check for RXR before DONE. Added comments to
ISR.
* Removed empty prepare/unprepare implementations.
* Removed use of devinit/devexit.
* Added BCM2835_ prefix to defines.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With the new OF DMA binding, it is possible to completely avoid the
need for platform_data for configuring a DMA channel. In cases where the
platform has already been converted, calling dma_request_slave_channel
should get all the necessary information from the device tree.
Like the patch that converts the dw_dma controller, this is completely
untested and is looking for someone to try it out.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: spi-devel-general@lists.sourceforge.net
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
This adds the capability to retrieve setup data from the device tree
node. The usage of platform data is still available.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix name of slink binding and address of sflash example to make it
self consistent.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the newly introduce cs-gpios dt support on atmel.
We do not use the hardware cs as it's wired and has bugs and limitations.
As the controller believes that only active-low devices/systems exists.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch allows to specify that a SPI device is connected in 3-wire mode via
device tree.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This will allow to use gpio for chip select with no modification in the
driver binding
When use the cs-gpios, the gpio number will be passed via the cs_gpio field
and the number of chip select will automatically increased with max(hw cs, gpio cs).
So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:
cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;
Then it should be configured so that num_chipselect = 4 with the
following mapping:
cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
[grant.likely: fixed up type of cs count so min() can do type checking]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
0384e90b8 ("spi/mcspi: allow configuration of pin directions") did what
it claimed to do the wrong way around. D0/D1 is configured as output by
*clearing* the bits in the conf registers, hence also breaking the
former default behaviour.
Fix this before that change is merged to mainline.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
NVIDIA's Tegra20 have the SPI (SFLASH) controller to
interface with spi flash device which is used for system
boot. Add the spi driver for this controller.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tegra20/Tegra30 supports the spi interface through its SLINK
controller. Add spi driver for SLINK controller.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow D0 to be an input and D1 to be an output, configurable via
platform data and a new DT property.
Based on a patch from Matus Ujhelyi <matus.ujhelyi@streamunlimited.com>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull MIPS update from Ralf Baechle:
"This is the MIPS update for 3.7.
A fair chunk of them are platform updates to the Cavium Octeon SOC
(which involves machine generated header files of considerable size),
Atheros ATH79xx, RMI aka Netlogic aka Broadcom XLP, Broadcom BCM63xx
platforms.
Support for the commercial MIPS simulator MIPSsim has been removed as
MIPS Technologies is shifting away from this product and Qemu is
offering various more powerful platforms. The generic MIPS code can
now also probe for no-execute / write-only TLB features implemented
without the full SmartMIPS extension as permitted by the latest MIPS
processor architecture. Lots of small changes to generic code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (78 commits)
MIPS: ath79: Fix CPU/DDR frequency calculation for SRIF PLLs
MIPS: ath79: use correct fractional dividers for {CPU,DDR}_PLL on AR934x
MIPS: BCM63XX: Properly handle mac address octet overflow
MIPS: Kconfig: Avoid build errors by hiding USE_OF from the user.
MIPS: Replace `-' in defconfig filename wth `_' for consistency.
MIPS: Wire kcmp syscall.
MIPS: MIPSsim: Remove the MIPSsim platform.
MIPS: NOTIFY_RESUME is not needed in TIF masks
MIPS: Merge the identical "return from syscall" per-ABI code
MIPS: Unobfuscate _TIF..._MASK
MIPS: Prevent hitting do_notify_resume() with !user_mode(regs).
MIPS: Replace 'kernel_uses_smartmips_rixi' with 'cpu_has_rixi'.
MIPS: Add base architecture support for RI and XI.
MIPS: Optimise TLB handlers for MIPS32/64 R2 cores.
MIPS: uasm: Add INS and EXT instructions.
MIPS: Avoid pipeline stalls on some MIPS32R2 cores.
MIPS: Make VPE count to be one-based.
MIPS: Add new end of interrupt functionality for GIC.
MIPS: Add EIC support for GIC.
MIPS: Code clean-ups for the GIC.
...
Even with devicetree support, we needed platform data to provide some data,
leading to mixed device tree and platform data. This patch makes it possible to
provide all that information via device tree. Now, the data must be provided
via platform data _or_ device tree completely.
Only in case of DMA where a callback specification is necessary (dma_filter()),
platform data is the only option.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add "clock-frequency" property, which allows configuring the SPI block's
base speed.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds DT bindings to the spi-gpio driver and some
documentation about how to use it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the driver, link it into the kbuild system and provide device tree
binding documentation.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/4292/
Signed-off-by: John Crispin <blogic@openwrt.org>
Several SPI controller drivers have defined differently named properties for
the number of chip selects. Now adding "num-cs" as a reference name for new
bindings.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds device tree support to the spi-pl022 driver.
Based on the initial patch by Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver adds support for NXP SC18IS602/603 I2C to SPI bus bridge.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since Grant is even more specacularly busy than usual for the time being
I've been collecting SPI patches for him for this release - probably
things will revert back to Grant before the next release. There's
nothing too exciting here, mostly it's simple driver specific stuff:
- Add spi: to the modaliases of SPI devices to provide namespacing.
- A driver for AD-FMCOMMS1-EBZ.
- DT binding for Orion.
- Fixes and cleanups for i.MX, PL0022, OMAP and bitbang drivers.
There may be a few more fixes I've missed, people keep sending me new
things.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=I2b9
-----END PGP SIGNATURE-----
Merge tag 'spi-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi updates from Mark Brown:
"Since Grant is even more specacularly busy than usual for the time
being I've been collecting SPI patches for him for this release -
probably things will revert back to Grant before the next release.
There's nothing too exciting here, mostly it's simple driver specific
stuff:
- Add spi: to the modaliases of SPI devices to provide namespacing.
- A driver for AD-FMCOMMS1-EBZ.
- DT binding for Orion.
- Fixes and cleanups for i.MX, PL0022, OMAP and bitbang drivers.
There may be a few more fixes I've missed, people keep sending me new
things."
* tag 'spi-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi/orion: remove uneeded spi_info
spi/bcm63xx: fix clock configuration selection
spi/orion: add device tree binding
spi/omap2: mark omap2_mcspi_master_setup as __devinit
spi: omap2-mcspi: Fix the below warning
spi: Add AD-FMCOMMS1-EBZ I2C-SPI bridge driver
spi/imx: use gpio_is_valid to determine if a gpio is valid
spi/imx: remove redundant config.speed_hz setting
spi/gpio: start with CS non-active
spi: tegra: use dmaengine based dma driver
spi/pl022: cleanup pl022 header documentation
spi/pl022: enable runtime PM
spi/pl022: delete DB5500 support
spi/pl022: disable port when unused
spi: Add "spi:" prefix to modalias attribute of spi devices
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Bindings for DMA channels are still under discussion and will
change once this has been resolved. Therefore we mark them
the newly added ones as preliminary. Let's hope nobody starts
relying on them...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim <kgene.kim@samsung.com>:
It is for supporting spi dt for exynos4210 and exynos5250, and got the
ack from Grant Likely for spi driver.
Note: Since this is including spi driver changes, so it was made based
on next/devel-dma-ops which touches same file, Samsung spi driver for
avoiding bad conflicts.
* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5
ARM: EXYNOS: Add spi clock support for EXYNOS5
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4
ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock
ARM: EXYNOS: Add device tree node for EXYNOS4 interrupt combiner controller
spi: s3c64xx: add device tree support
spi: s3c64xx: Remove the 'set_level' callback from controller data
ARM: SAMSUNG: Modify s3c64xx_spi{0|1|2}_set_platdata function
ARM: SAMSUNG: Remove pdev pointer parameter from spi gpio setup functions
spi: s3c64xx: move controller information into driver data
spi: s3c64xx: remove unused S3C64XX_SPI_ST_TRLCNTZ macro
ARM: S3C64XX: Add a new dma request id for device tree based dma channel lookup
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for device based discovery.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The gpio numbers does not match the comment.
Fix the comments for GPIOs used for chip selects.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rename all Tegra binding documentation according to the first or
primary compatible value they describe. This provides a clear naming
scheme for the files, and prevents any naming conflicts should future
SoC versions require their own binding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add device tree support to the OMAP2+ McSPI driver.
Add the bindings documentation.
Based on original code from Rajendra.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It adds device tree probe support for spi-imx driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Engineering names are more stable than marketing names. Hence, use them
for Device Tree compatible properties instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds a new SPI driver to support the Altera SOPC Builder
SPI component. It uses the bitbanging library.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support of OpenCores tiny SPI driver.
http://opencores.org/project,tiny_spi
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device tree is used by more than just PowerPC. Make the documentation
directory available to all.
v2: reorganized files while moving to create arch and driver specific
directories.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
