The clocks of A64/H5 SoCs in the DE2 CCU is the same as the clocks in H3
DE2 CCU rather than the A83T DE2 CCU (the parent of them is the DE
module clock).
Fix this by change the clock descriptions to use the clocks of H3.
Fixes: 763c5bd045 ("clk: sunxi-ng: add support for DE2 CCU")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner H3 features a DE2 CCU like the one on A83T, however the
parent of the clocks is the DE module clock, not the PLL_DE clock.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The audio blocks require specific clock rates. Until now we were using
the closest clock rate possible with integer N-M factors. This resulted
in audio playback being slightly slower than it should be.
The vendor kernel gets around this (for newer SoCs) by using sigma-delta
modulation to generate a fractional-N factor. This patch copies the
parameters for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A83T, the audio PLL should have its div1 set to 0, or /1, and
div2 set to 1, or /2. This setting is the default, and is required
to match the sigma-delta modulation parameters from the BSP kernel.
This patch adds a /2 fixed post divider to the audio PLL, and fixes
the enforced d1 & d2 values. This also resolves the mismatch between
the values mentioned in the comment for the audio PLL, and the actual
enforced values.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A83T, the audio PLL should have its div1 set to 0, or /1, and
div2 set to 1, or /2. This setting is the default, and is required
to match the sigma-delta modulation parameters from the BSP kernel.
To do this, we first add fixed post-divider to the NM style clocks,
which is the type of clock the audio PLL clock is modeled into.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A64, the MMC module clocks are fixed in the new timing mode,
i.e. they do not have a bit to select the mode. These clocks have
a 2x divider somewhere between the clock and the MMC module.
To be consistent with other SoCs supporting the new timing mode,
we model the 2x divider as a fixed post-divider on the MMC module
clocks.
This patch adds the post-dividers to the MMC clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A64, the MMC module clocks are fixed in the new timing mode,
i.e. they do not have a bit to select the mode. These clocks have
a 2x divider somewhere between the clock and the MMC module.
To be consistent with other SoCs supporting the new timing mode,
we model the 2x divider as a fixed post-divider on the MMC module
clocks.
To do this, we first add fixed post-divider to the MP style clocks,
which the MMC module clocks are.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fix ptr_ret.cocci warnings:
drivers/clk/sunxi/clk-sun8i-apb0.c:101:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
large change that introduces runtime PM support to the clk framework. Now we
properly call runtime PM operations on the device providing a clk when the clk
is in use. This helps on SoCs where the clks provided by a device need
something to be powered on before using the clks, like power domains or
regulators. It also helps power those things down when clks aren't in use. The
other core change is a devm API addition for clk providers so we can get rid of
a bunch of clk driver remove functions that are just doing
of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and smattering
of non-critical fixes to existing drivers. The biggest diff is support for
Mediatek MT2712 and MT7622 SoCs, but those patches really just add a bunch
of data.
By the way, we're trying something new here where we build the tree up with
topic branches. We plan to work this into our workflow so that we don't step
on each other's toes, and so the fixes branch can be merged on an as-needed
basis.
Core:
- Runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- Runtime PM support for Samsung exynos5433/exynos4412 providers
- Removal of clkdev aliases on Samsung SoCs
- Convert clk-gpio to use gpio descriptors
- Various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- Sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- Support for the second display unit clock on Renesas RZ/G1E
- Suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- New clock ids for Rockchip rk3188 and rk3368 SoCs
- Various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJaD3qRAAoJEK0CiJfG5JUlOLgQAKWekgG/IYgcPzPWDYfg8Hwr
sVVUK7+q7TVfbHsbYVikJuUaxutKZ0onnrYmOalTTyyxqL2E1/rYScnxdYHfcwX8
cyfHebRHsbh/Xg45ktwjzBkO49nwuppkpXd/V80GSBUZ+lsIVl5DUrrFAZdRUEdr
CEsAsF9tEWIl+0gqXYNuiKBV7QAYv5BUPrbJQf0PwL6jX0OAhLv+ukfN8BdmYsOb
rdoqhdgmyHkTuIMqsC/H2yP59aAKBse7wxIYebDiTdbPWfTkC9q927fTs4A02F6L
sHfLvCpfuB4rOjXy6LSd1gMGWIcjotZai+idHBqtNLLVz6exF1QpUCp+pZjEULbA
/Sx9lk8A3cYoa8pTu1NrrZbZX17iHkFswqMF3T20nhUN9+Ti597ZEbRcWDcoEZtw
v2NznOTJ7Mm2SrNHOvDklstggNIGcwiAEePGMo7rJNEQZChpDjQj/gJWKzn0UwL4
zfk+0EzoejPdvZ5FJUfmlr8Tqk53uw+y7/0xQ6gf8lDviTrzzoeXtJUyumGBiuGx
RxFywf8n02oLYRJm5hu+0NkC+/bX0Lxg/kwiR6FLBFbBFgkWyp7FGcxhlm6ZiBfe
0KkPciWslNavn5KhljIkZDbXymbvhhSr9uBEFsyeJueA5q7sSghWloL8Ag1cac3W
e6swD1ngXtM/t5gjOLhR
=hC7z
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have two changes to the core framework this time around.
The first being a large change that introduces runtime PM support to
the clk framework. Now we properly call runtime PM operations on the
device providing a clk when the clk is in use. This helps on SoCs
where the clks provided by a device need something to be powered on
before using the clks, like power domains or regulators. It also helps
power those things down when clks aren't in use.
The other core change is a devm API addition for clk providers so we
can get rid of a bunch of clk driver remove functions that are just
doing of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and
smattering of non-critical fixes to existing drivers. The biggest diff
is support for Mediatek MT2712 and MT7622 SoCs, but those patches
really just add a bunch of data.
By the way, we're trying something new here where we build the tree up
with topic branches. We plan to work this into our workflow so that we
don't step on each other's toes, and so the fixes branch can be merged
on an as-needed basis.
Summary:
Core:
- runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- runtime PM support for Samsung exynos5433/exynos4412 providers
- removal of clkdev aliases on Samsung SoCs
- convert clk-gpio to use gpio descriptors
- various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- support for the second display unit clock on Renesas RZ/G1E
- suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- new clock ids for Rockchip rk3188 and rk3368 SoCs
- various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: stm32h7: fix test of clock config
clk: pxa: fix building on older compilers
clk: sunxi-ng: a83t: Fix i2c buses bits
clk: ti: dra7-atl-clock: fix child-node lookups
clk: qcom: common: fix legacy board-clock registration
clk: uniphier: fix DAPLL2 clock rate of Pro5
clk: uniphier: fix parent of miodmac clock data
clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
clk: hi3660: fix incorrect uart3 clock freqency
clk: kona-setup: Delete error messages for failed memory allocations
ARC: clk: fix spelling mistake: "configurarion" -> "configuration"
clk: cdce925: remove redundant check for non-null parent_name
clk: versatile: Improve sizeof() usage
clk: versatile: Delete error messages for failed memory allocations
clk: ux500: Improve sizeof() usage
clk: ux500: Delete error messages for failed memory allocations
clk: spear: Delete error messages for failed memory allocations
clk: ti: Delete error messages for failed memory allocations
clk: mmp: Adjust checks for NULL pointers
...
This branch contains platform-related driver updates for ARM and ARM64,
these are the areas that bring the changes:
New drivers:
- Driver support for Renesas R-Car V3M (R8A77970)
- Power management support for Amlogic GX
- A new driver for the Tegra BPMP thermal sensor
- A new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- The usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa, uniphier
and mediatek families.
- Updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi.
Changes specific to some ARM-based SoC
- The Freescale/NXP DPAA QBMan drivers from PowerPC can now work
on ARM as well.
- Several changes for power management on Broadcom SoCs
- Various improvements on Qualcomm, Broadcom, Amlogic, Atmel, Mediatek
- Minor Cleanups for Samsung, TI OMAP SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qDhq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This branch contains platform-related driver updates for ARM and
ARM64, these are the areas that bring the changes:
New drivers:
- driver support for Renesas R-Car V3M (R8A77970)
- power management support for Amlogic GX
- a new driver for the Tegra BPMP thermal sensor
- a new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- the usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa,
uniphier and mediatek families
- updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi
Changes specific to some ARM-based SoC
- the Freescale/NXP DPAA QBMan drivers from PowerPC can now work on
ARM as well
- several changes for power management on Broadcom SoCs
- various improvements on Qualcomm, Broadcom, Amlogic, Atmel,
Mediatek
- minor Cleanups for Samsung, TI OMAP SoCs"
[ NOTE! This doesn't work without the previous ARM SoC device-tree pull,
because the R8A77970 driver is missing a header file that came from
that pull.
The fact that this got merged afterwards only fixes it at this point,
and bisection of that driver will fail if/when you walk into the
history of that driver. - Linus ]
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (96 commits)
soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader
bus: add driver for the Technologic Systems NBUS
memory: omap-gpmc: Remove deprecated gpmc_update_nand_reg()
soc: qcom: remove unused label
soc: amlogic: gx pm domain: add PM and OF dependencies
drivers/firmware: psci_checker: Add missing destroy_timer_on_stack()
dt-bindings: power: add amlogic meson power domain bindings
soc: amlogic: add Meson GX VPU Domains driver
soc: qcom: Remote filesystem memory driver
dt-binding: soc: qcom: Add binding for rmtfs memory
of: reserved_mem: Accessor for acquiring reserved_mem
of/platform: Generalize /reserved-memory handling
soc: mediatek: pwrap: fix fatal compiler error
soc: mediatek: pwrap: fix compiler errors
arm64: mediatek: cleanup message for platform selection
soc: Allow test-building of MediaTek drivers
soc: mediatek: place Kconfig for all SoC drivers under menu
soc: mediatek: pwrap: add support for MT7622 SoC
soc: mediatek: pwrap: add common way for setup CS timing extenstion
soc: mediatek: pwrap: add MediaTek MT6380 as one slave of pwrap
..
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
gcc-4.4 got confused by the inline assembler statement:
drivers/clk/pxa/clk-pxa.c: In function 'pxa2xx_core_turbo_switch':
drivers/clk/pxa/clk-pxa.c:152: error: expected string literal before ')' token
This removes the extraneous ':' to let all compilers parse the
driver correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
i2c1 and i2c2 bits for CCU are not bit 0 but bit 1 and bit 2.
Because of that, the i2c0 (bit 0) was not correctly configured.
Fixed the correct bits for i2c1 and i2c2.
Fixes: 05359be117 ("clk: sunxi-ng: Add driver for A83T CCU")
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix child node-lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
Note that the original premature free of the parent node has already
been fixed separately, but that fix was apparently never backported to
stable.
Fixes: 9ac33b0ce8 ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Fixes: 660e155193 ("clk: ti: dra7-atl-clock: Fix of_node reference counting")
Cc: stable <stable@vger.kernel.org> # 3.16: 660e155193
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Make sure to search only the child nodes of "/clocks", rather than the
whole device-tree depth-first starting at "/clocks" when determining
whether to register a fixed clock in the legacy board-clock registration
helper.
Fixes: ee15faffef ("clk: qcom: common: Add API to register board clocks backwards compatibly")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-const:
clk: make clk_init_data const
clk: imx: make clk_ops const
clk: mmp: make clk_ops const
clk: hisilicon: make clk_ops const
clk: mxs: make clk_ops const
clk: sirf: make clk_ops const
clk: spear: make clk_ops const
CLK: SPEAr: make aux_clk_masks structures const
CLK: SPEAr: make structure field and function argument as const
The parent of DAPLL2 should be DAPLL1. Fix the clock connection.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The "miodmac" is not a child of "stdmac". They are independent
from each other. Fix it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Other than 'mmc_mux', 'clk_sdio0_ciu' uses a different parent mux clock.
Let's add this mux clock as 'sdio0_mux', and correct the parent of
'clk_sdio0_ciu' to be it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
UART3 clock rate is doubled in previous commit.
This error is not detected until recently a mezzanine board which makes
real use of uart3 port (through LS connector of 96boards) was setup
and tested on hi3660-hikey960 board.
This patch changes clock source rate of clk_factor_uart3 to 100000000.
Signed-off-by: Zhong Kaihua <zhongkaihua@huawei.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in this
function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The check for a non-null parent_name is always true as there is an
earlier check for a null parent_name that returns -ENODEV. Remove this
redundant check and always set init.num_parents to 1.
Detected by CoverityScan CID#1309477 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Replace the specification of a data structure by a pointer
dereference as the parameter for the operator "sizeof" to make
the corresponding size determination a bit safer according to the
Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in this
function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Replace the specification of data structures by pointer
dereferences as the parameter for the operator "sizeof" to make
the corresponding size determination a bit safer according to the
Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The script “checkpatch.pl” pointed information out like the
following:
Comparison to NULL could be written !...
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a jump target so that a bit of exception handling can be
better reused at the end of this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The script “checkpatch.pl” pointed information out like the
following.
Comparison to NULL could be written ...
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Omit extra messages for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a missing character in these descriptions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use space characters at some source code places according to the
Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Replace the specification of data structures by pointer
dereferences as the parameter for the operator "sizeof" to make
the corresponding size determination a bit safer according to the
Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
