This patch increases the default for nopin_timeout to 15 seconds (wait
between sending a new NopIN ping) and nopin_response_timeout to 30 seconds
(wait for NopOUT response before failing the connection) in order to avoid
false positives by iSCSI Initiators who are not always able (under load) to
respond to NopIN echo PING requests within the current 5 second window.
False positives have been observed recently using Open-iSCSI code on v3.3.x
with heavy large-block READ workloads over small MTU 1 Gb/sec ports, and
increasing these values to more reasonable defaults significantly reduces
the possibility of false positive NopIN response timeout events under
this specific workload.
Historically these have been set low to initiate connection recovery as
soon as possible if we don't hear a ping back, but for modern v3.x code
on 1 -> 10 Gb/sec ports these new defaults make alot more sense.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make sure all on the wire types are use as big endian and big endian only so
that sparse can verify all the conversions are done right.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use the special itt_t type defined by the iscsi headers and the initiator
to make sure it's an opaque value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Sparse noticed that INADDR_ANY needs to be converted to big endian before
it can be stored in struct sockaddr_in.s_addr.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix a potential multiple spin-unlock -> deadlock scenario during the
overflow check within iscsit_build_sendtargets_resp() as found by
sparse static checking.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch marks a number of functions static to appease sparse static
checking.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Clang warns about this bug:
drivers/target/iscsi/iscsi_target_erl0.c:52:45: warning: operator '?:'
has lower precedence than '+'; '+' will be evaluated first
[-Wparentheses]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch carries forward a work-around from tcm_loop to target
core code to explicitly clear control CDB READ paylods in order to
avoid bugs in scsi-generic user-space code for INQUIRY that do not
explicitly zero CDB payload memory.
(v2: Drop TARGET_SCF_MAP_CLEAR_MEM, and perform the explicit zero
of READ memory for all target_submit_cmd_map_sgls users)
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts tcm_loop to use target_submit_cmd_map_sgls() for
I/O submission and mapping of pre-allocated SGL memory from incoming
scsi_cmnd -> se_cmd descriptors.
This includes removing the original open-coded fabric uses of target
core callers to support transport_generic_map_mem_to_cmd() between
target_setup_cmd_from_cdb() and transport_handle_cdb_direct() logic.
(v2: Use renamed target_submit_cmd_map_sgls)
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new target_submit_cmd_map_sgls() to pass pre-allocated
SGL memory using transport_generic_map_mem_to_cmd() logic into the generic
target submit I/O codepath.
It also adds a target_submit_cmd() wrapper around target_submit_cmd_map_sgls()
for existing fabric code that already assumes internal target-core SGL memory
allocation.
(v2: Rename to target_submit_cmd_map_sgls + drop TARGET_SCF_MAP_MEM flag
in favor of non zero sgl_count check)
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We've had reports in the past about this specific case, so it's time to
go ahead and explicitly set cache_dynamic_acls=1 for generate_node_acls=1
(TPG demo-mode) operation.
During normal generate_node_acls=0 operation with explicit NodeACLs ->
se_node_acl memory is persistent to the configfs group located at
/sys/kernel/config/target/$TARGETNAME/$TPGT/acls/$INITIATORNAME, so in
the generate_node_acls=1 case we want the reservation logic to reference
existing per initiator IQN se_node_acl memory (not to generate a new
se_node_acl), so go ahead and always set cache_dynamic_acls=1 when
TPG demo-mode is enabled.
Reported-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts iscsi_target_seq_pdu_list.c code for DataSequenceInOrder=No +
DataPDUInOrder=No operation to honor the MaxXmitDataSegmentLength value
for iscsi_cmd->se_cmd.data_direction == DMA_TO_DEVICE cases.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Andy Grover <agrover@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The iSCSI TMR TASK_REASSIGN completion logic in iscsi_tmr_task_reassign()
does an explict check for MRDSL across task reassignment, so go ahead and
add an explict MaxXmitDataSegmentLength check here as well to be safe.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Andy Grover <agrover@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that iscsi-target supports a local configurable MaxXmitDataSegmentLength,
go ahead and make ISCSI_OP_SCSI_CMD, ISCSI_OP_SCSI_DATA_OUT, ISCSI_OP_NOOP_OUT
and ISCSI_OP_TEXT PDU payload checks honor conn_ops->MaxXmitDataSegmentLength.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Andy Grover <agrover@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch activates MaxXmitDataSegmentLength usage that performs the
following sequence of events:
- Once the incoming initiator's MAXRECVDATASEGMENTLENGTH key is detected
within iscsi_check_acceptor_state(), save the requested MRDSL into
conn->conn_ops->MaxRecvDataSegmentLength
- Next change the outgoing target's MaxRecvDataSegmenthLength key=value
based upon the local TPG's MaxXmitDataSegmentLength attribute value.
- Change iscsi_set_connection_parameters() to skip the assignment of
conn->conn_ops->MaxRecvDataSegmentLength, now setup within
iscsi_check_acceptor_state()
Also update iscsi_decode_text_input() -> iscsi_check_acceptor_state()
code-path to accept struct iscsi_conn *.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Andy Grover <agrover@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch introduces a new per connection MaxXmitDataSegmentLength
parameter value used to represent the outgoing MaxRecvDataSegmentLength
that is actually sent over the wire during iSCSI login response back
to the initiator side.
It also adds a new MaxXmitDataSegmentLength configfs attribute to
represent this value within the existing TPG parameter group under
/sys/kernel/config/target/iscsi/$TARGETNAME/$TPGT/param/
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Andy Grover <agrover@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch re-adds the ability to optionally run in buffered FILEIO mode
(eg: w/o O_DSYNC) for device backends in order to once again use the
Linux buffered cache as a write-back storage mechanism.
This logic was originally dropped with mainline v3.5-rc commit:
commit a4dff3043c
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Wed May 30 16:25:41 2012 -0700
target/file: Use O_DSYNC by default for FILEIO backends
This difference with this patch is that fd_create_virtdevice() now
forces the explicit setting of emulate_write_cache=1 when buffered FILEIO
operation has been enabled.
(v2: Switch to FDBD_HAS_BUFFERED_IO_WCE + add more detailed
comment as requested by hch)
Reported-by: Ferry <iscsitmp@bananateam.nl>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a missing iscsi_reject->ffffffff assignment within
iscsit_send_reject() code to properly follow RFC-3720 Section 10.17
Bytes 16 -> 19 for the PDU format definition of ISCSI_OP_REJECT.
We've not seen any initiators care about this bytes in practice, but
as Ronnie reported this was causing trouble with wireshark packet
decoding lets go ahead and fix this up now.
Reported-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case of error, the function target_fabric_configfs_init() returns
ERR_PTR() not NULL pointer. The NULL test in the return value check
should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes error cases within target_core_init_configfs() to
properly set ret = -ENOMEM before jumping to the out_global exception
path.
This was originally discovered with the following Coccinelle semantic
match information:
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function. A simplified version of the semantic match
that finds this problem is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The dereference should be moved below the NULL test.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The dereference should be moved below the NULL test.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Yay, all users of transport_kmap_data_sg now check for a zero-length
request and/or a too-small parameter list length. We can thus go through
the normal emulation path even for such commands.
This means that out-of-bounds reads and writes are now reported correctly
even if they transfer 0 blocks. Other errors are also reported correctly.
Testcase: sg_raw /dev/sdb 28 00 80 00 00 00 00 00 00 00
should fail with ILLEGAL REQUEST / LBA OUT OF RANGE sense
does not fail without the patch
(still wrong with the patch, but better: the ASC is INVALID FIELD IN CDB)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
scsi_setup_fs_cmnd does not like to receive requests with no
bios attached to it. Special-case zero-length reads and writes,
by not submitting any bio.
Testcase: sg_raw /dev/sdb 28 00 00 00 00 00 00 00 00 00
should not fail
panics with the rest of the series but not this patch
behaves correctly without or with this series
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
READ CAPACITY must be subject to the same treatment as INQUIRY,
REQUEST SENSE, and MODE SENSE, but there are no pre-existing bugs
to fix here. Just use an on-stack buffer, and copy to it after
checking the return value of transport_kmap_data_sg.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The offset was not bumped back to the full size after writing the
header of the MODE SENSE response, so the last 1 or 2 bytes were
not copied.
On top of this, support zero-length requests by checking for the
return value of transport_kmap_data_sg.
Testcase: sg_raw -r20 /dev/sdb 5a 00 0a 00 00 00 00 00 14 00
last byte should be 0x1e
it is 0x00 without the patch
it is correct with the patch
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
INQUIRY processing already uses an on-heap bounce buffer for loopback,
but not for other fabrics. Switch this to a cheaper on-stack bounce
buffer, similar to the one used by MODE SENSE and REQUEST SENSE, and
use it unconditionally. With this in place, zero allocation length is
handled simply by checking the return address of transport_kmap_data_sg.
Testcase: sg_raw /dev/sdb 12 00 83 00 00 00
should fail with ILLEGAL REQUEST / INVALID FIELD IN CDB sense
does not fail without the patch
fails correctly with the series
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Using list_move_tail() instead of list_del() + list_add_tail().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There's no need for iscsi_target_init_negotiation() to print
iSCSI Login negotiation failed.
on failure, since its only caller (__iscsi_target_login_thread())
prints exactly the same message if it gets an error return back.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops se_subsystem_api->[write_cache,fua_write]_emulated flags
set by viritual FILEIO/IBLOCK/RD_MCP backend drivers in favor of explict
TRANSPORT_PLUGIN_PHBA_PDEV checks to know when to fail if userspace is
attempting to set virtual emulation bits for an pSCSI (passthrough)
backend device.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove including <generated/utsrelease.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove including <generated/utsrelease.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the missing rd_mcp_template->write_cache_emulated=1 bit to
optionally allow WriteCacheEnabled=1 (WCE) to be enabled for the built-in
TCM/rd_mcp backend driver.
Tested on v3.6-rc[0,2] code with loopback+tcm_vhost fabric ports.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Following commit dbc6e0222 from Al Viro for fileio, go ahead and make
Opt_udev_path within iblock_set_configfs_dev_params use match_strlcpy
instead of the match_strdup -> snprintf -> kfree equivalent.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Correct spelling typo in printk and comment within drivers/target.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Every fabric driver has to supply a se_tfo->set_fabric_sense_len()
method, just so iSCSI can return an offset of 2. However, every fabric
driver is already allocating a sense buffer and passing it into the
target core, either via transport_init_se_cmd() or target_submit_cmd().
So instead of having iSCSI pass the start of its sense buffer into the
core and then later tell the core to skip the first 2 bytes, it seems
easier for iSCSI just to do the offset of 2 when it passes the sense
buffer into the core. Then we can drop the se_tfo->set_fabric_sense_len()
everywhere, and just add a couple of lines of code to iSCSI to set the
sense data length to the beginning of the buffer right before it sends
it over the network.
(nab: Remove .set_fabric_sense_len usage from tcm_qla2xxx_npiv_ops +
change transport_get_sense_buffer to follow v3.6-rc6 code w/o
->set_fabric_sense_len usage)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There are no callers of se_tfo->get_fabric_sense_len(), so we should
stop having every fabric driver implement it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's always set, and controls whether uppercase A-F are allowed hex values.
I don't see a reason not to accept these.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move static into function body from file scope.
Remove extraneous return statement
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that spc_emulate_request_sense has been taught to process zero-length
REQUEST SENSE correctly, drop the special handling of unit attention
conditions from transport_generic_new_cmd. However, for now REQUEST SENSE
will be the only command that goes through emulation for zero lengths.
(nab: Fix up zero-length check in transport_generic_new_cmd)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Similar to INQUIRY and MODE SENSE, construct the sense data in a
buffer and later copy it to the scatterlist. Do not do anything,
but still clear a pending unit attention condition, if the allocation
length is zero.
However, SPC tells us that "If a REQUEST SENSE command is terminated with
CHECK CONDITION status [and] the REQUEST SENSE command was received on
an I_T nexus with a pending unit attention condition (i.e., before the
device server reports CHECK CONDITION status), then the device server
shall not clear the pending unit attention condition." Do the
transport_kmap_data_sg early to detect this case.
It also tells us "Device servers shall not adjust the additional sense
length to reflect truncation if the allocation length is less than the
sense data available", so do not do that! Note that the err variable
is write-only.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In order to support zero-size allocation lengths, do not assert
that we have a scatterlist until after checking cmd->data_length.
But once we do this, we can have two cases of transport_kmap_data_sg
returning NULL: a zero-size allocation length, or an out-of-memory
condition. Report the latter using sense codes, so that the SCSI
command that triggered it will fail.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SPC says:
"The ALLOCATION LENGTH field is defined in 4.3.5.6. The allocation length
should be at least 16. Device servers compliant with SPC return CHECK
CONDITION status, with the sense key set to ILLEGAL REQUEST, and the
additional sense code set to INVALID FIELD IN CDB when the allocation
length is less than 16 bytes".
Testcase: sg_raw -r8 /dev/sdb a0 00 00 00 00 00 00 00 00 08 00 00
should fail with ILLEGAL REQUEST / INVALID FIELD IN CDB sense
does not fail without the patch
fails correctly with the patch
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Several places were not checking that the parameter list length
was large enough, and thus accessing invalid memory. Zero-length
parameter lists are just a special case of this.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Right now, commands with a zero-size payload are skipped completely.
This is wrong; such commands should be passed down to the device and
processed normally.
For physical backends, this ignores completely things such as START
STOP UNIT. For virtual backends, we have a hack in place to clear a
unit attention state on a zero-size REQUEST SENSE, but we still do
not report errors properly on zero-length commands---out-of-bounds
0-block reads and writes, too small parameter list lengths, etc.
This patch fixes this for PSCSI. Uses of transport_kmap_data_sg are
guarded with a check for non-zero cmd->data_length; for all other
commands a zero length is handled properly in pscsi_execute_cmd.
The sole exception will be for now REPORT LUNS, which is handled
through the normal SPC emulation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The pointer to the sense buffer is fetched by transport_get_sense_data,
but this is called by target_complete_ok_work long after pscsi_req_done
has freed the struct that contains it.
Pass instead the fabric's sense buffer to transport_complete,
and copy the data to it directly in transport_complete. Setting
SCF_TRANSPORT_TASK_SENSE also becomes a duty of transport_complete.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The error conditions in transport_get_sense_data are superfluous
and complicate the code unnecessarily:
* SCF_TRANSPORT_TASK_SENSE is checked in the caller;
* it's simply part of the invariants of dev->transport->get_sense_buffer
that it must be there if transport_complete ever returns 1, and that
it must not return NULL. Besides, the entire callback will disappear
with the next patch.
* similarly in the caller we can expect that sense data is only sent
for non-zero cmd->scsi_status.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We will be calling it from transport_complete_cmd, avoid forward
declarations. No semantic change.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates iscsi_login_zero_tsih_s1() usage for generating
iscsi_session->session_index to properly check the return value from
idr_get_new(), and reject the iSCSI login attempt with exception
status ISCSI_LOGIN_STATUS_NO_RESOURCES in the event of a failure.
Signed-off-by: Benjamin Wang <cpwang2009@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
