* 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (202 commits)
MAINTAINERS: update KVM entry
KVM: correct error-handling code
KVM: fix compile warnings on s390
KVM: VMX: Check cpl before emulating debug register access
KVM: fix misreporting of coalesced interrupts by kvm tracer
KVM: x86: drop duplicate kvm_flush_remote_tlb calls
KVM: VMX: call vmx_load_host_state() only if msr is cached
KVM: VMX: Conditionally reload debug register 6
KVM: Use thread debug register storage instead of kvm specific data
KVM guest: do not batch pte updates from interrupt context
KVM: Fix coalesced interrupt reporting in IOAPIC
KVM guest: fix bogus wallclock physical address calculation
KVM: VMX: Fix cr8 exiting control clobbering by EPT
KVM: Optimize kvm_mmu_unprotect_page_virt() for tdp
KVM: Document KVM_CAP_IRQCHIP
KVM: Protect update_cr8_intercept() when running without an apic
KVM: VMX: Fix EPT with WP bit change during paging
KVM: Use kvm_{read,write}_guest_virt() to read and write segment descriptors
KVM: x86 emulator: Add adc and sbb missing decoder flags
KVM: Add missing #include
...
Debug registers may only be accessed from cpl 0. Unfortunately, vmx will
code to emulate the instruction even though it was issued from guest
userspace, possibly leading to an unexpected trap later.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
No need to call it before each kvm_(set|get)_msr_common()
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Only reload debug register 6 if we're running with the guest's
debug registers. Saves around 150 cycles from the guest lightweight
exit path.
dr6 contains a couple of bits that are updated on #DB, so intercept
that unconditionally and update those bits then.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Instead of saving the debug registers from the processor to a kvm data
structure, rely in the debug registers stored in the thread structure.
This allows us not to save dr6 and dr7.
Reduces lightweight vmexit cost by 350 cycles, or 11 percent.
Signed-off-by: Avi Kivity <avi@redhat.com>
Don't call adjust_vmx_controls() two times for the same control.
It restores options that were dropped earlier. This loses us the cr8
exit control, which causes a massive performance regression Windows x64.
Cc: stable@kernel.org
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We know no pages are protected, so we can short-circuit the whole thing
(including fairly nasty guest memory accesses).
Signed-off-by: Avi Kivity <avi@redhat.com>
QNX update WP bit when paging enabled, which is not covered yet. This one fix
QNX boot with EPT.
Cc: stable@kernel.org
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Segment descriptors tables can be placed on two non-contiguous pages.
This patch makes reading segment descriptors by linear address.
Signed-off-by: Mikhail Ershov <Mike.Ershov@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add missing decoder flags for adc and sbb instructions
(opcodes 0x14-0x15, 0x1c-0x1d)
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
According to 16.2.5 in the SDM, eflags.vm in the tss is consulted before loading
and new segments. If eflags.vm == 1, then the segments are treated as 16-bit
segments. The LDTR and TR are not normally available in vm86 mode so if they
happen to somehow get loaded, they need to be treated as 32-bit segments.
This fixes an invalid vmentry failure in a custom OS that was happening after
a task switch into vm8086 mode. Since the segments were being mistakenly
treated as 32-bit, we loaded garbage state.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We set rflags.vm86 when virtualizing real mode to do through vm8086 mode;
so we need to take it out again when reading rflags.
Signed-off-by: Avi Kivity <avi@redhat.com>
Since on vcpu entry we do it only if apic is enabled we should do
it when TPR is changed while apic is disabled. This happens when windows
resets HW without setting TPR to zero.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Nested SVM is (in my experience) stable enough to be enabled by
default. So omit the requirement to pass a module parameter.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Not checking for this flag breaks any nested hypervisor that does not
set VINTR. So fix it with this patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch removes one indentation level from nested_svm_intr and
makes the logic more readable.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This check is not necessary. We have to sync the vcpu->arch.cr2 always
back to the VMCB. This patch remove the is_nested check.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch moves the handling for special nested vmexits like #pf to a
separate function. This makes the kvm_override parameter obsolete and
makes the code more readable.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If nested svm fails to load the msrpm the vmrun succeeds with the old
msrpm which is not correct. This patch changes the logic to roll back
to host mode in case the msrpm cannot be loaded.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch removes the usage of nested_svm_do from the vmrun emulation
path.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch removes the usage of nested_svm_do from the vmload and
vmsave emulation code paths.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch changes nested svm to call nested_svm_exit_handled_msr
directly and not through nested_svm_do.
[alex: fix oops due to nested kmap_atomics]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch is the starting point of removing nested_svm_do from the
nested svm code. The nested_svm_do function basically maps two guest
physical pages to host virtual addresses and calls a passed function
on it. This function pointer code flow is hard to read and not the
best technical solution here.
As a side effect this patch indroduces the nested_svm_[un]map helper
functions.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Makes the code of this function more readable by removing on
indentation level for the core logic.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If this function returns true a nested vmexit is required. Move that
vmexit into the nested_svm_exit_handled function. This also simplifies
the handling of nested #pf intercepts in this function.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When caching guest intercepts there is no need anymore for the
nested_svm_exit_handled_real function. So move its code into
nested_svm_exit_handled.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When the nested intercepts are cached we don't need to call
get_user_pages and/or map the nested vmcb on every nested #vmexit to
check who will handle the intercept.
Further this patch aligns the emulated svm behavior better to real
hardware.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This makes it more clear for which purpose these members in the vcpu_svm
exist.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The interrupt completion code must run after nested exits are handled
because not injected interrupts or exceptions may be handled by the l1
guest first.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The vmcb control area contains more then 800 bytes of reserved fields
which are unnecessarily copied. Fix this by introducing a copy
function which only copies the relevant part and saves time.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Only copy the necessary parts of the vmcb save area on vmrun and save
precious time.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
It is more efficient to copy only the relevant parts of the vmcb back to
the nested vmcb when we emulate an vmexit.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch makes the code easier to read when it comes to setting,
clearing and checking the status of the virtualized global
interrupt flag for the VCPU.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently they are called when irq vector is been delivered. Calling ack
notifiers at this point is wrong. Device assignment ack notifier enables
host interrupts, but guest not yet had a chance to clear interrupt
condition in a device.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
d5ecfdd25 moved it out because back than it was impossible to
call it inside spinlock. This restriction no longer exists.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Check whether index is within bounds before grabbing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
We ignore writes to the perfctr msrs. Ignore reads as well.
Kaspersky antivirus crashes Windows guests if it can't read
these MSRs.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of calling vmx_get_segment() (which reads a whole bunch of
vmcs fields), read only the cs selector which contains the cpl.
Signed-off-by: Avi Kivity <avi@redhat.com>
So far unprivileged guest callers running in ring 3 can issue, e.g., MMU
hypercalls. Normally, such callers cannot provide any hand-crafted MMU
command structure as it has to be passed by its physical address, but
they can still crash the guest kernel by passing random addresses.
To close the hole, this patch considers hypercalls valid only if issued
from guest ring 0. This may still be relaxed on a per-hypercall base in
the future once required.
Cc: stable@kernel.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Remove the bogus n_free_mmu_pages assignment from alloc_mmu_pages.
It breaks accounting of mmu pages, since n_free_mmu_pages is modified
but the real number of pages remains the same.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
First check if the list is empty before attempting to look at list
entries.
Cc: stable@kernel.org
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This takes care of the following entries from Dan's list:
arch/x86/kvm/i8254.c +714 kvm_inject_pit_timer_irqs(6) warning: variable derefenced in initializer 'vcpu'
arch/x86/kvm/i8254.c +714 kvm_inject_pit_timer_irqs(6) warning: variable derefenced before check 'vcpu'
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: corbet@lwn.net
Cc: eteo@redhat.com
Cc: Julia Lawall <julia@diku.dk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If userspace knows that the kernel part supports 1GB pages it can enable
the corresponding cpuid bit so that guests actually use GB pages.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds support for shadow paging to the 1gb page table code in KVM.
With this code the guest can use 1gb pages even if the host does not support
them.
[ Marcelo: fix shadow page collision on pmd level if a guest 1gb page is mapped
with 4kb ptes on host level ]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The page walker may be used with nested paging too when accessing mmio
areas. Make it support the additional page-level too.
[ Marcelo: fix reserved bit check for 1gb pte ]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
With the new name and the corresponding backend changes this function
can now support multiple hugepage sizes.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch removes the largepage parameter from the rmap_add function.
Together with rmap_remove this function now uses the role.level field to
find determine if the page is a huge page.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Otherwise its possible to starve the host by programming lapic timer
with a very high frequency.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit f0a3602c20 ("KVM: Move interrupt injection logic to x86.c") does not
update the cr8 intercept if the lapic is disabled, so when userspace updates
cr8, the cr8 threshold control is not updated and we are left with illegal
control fields.
Fix by explicitly resetting the cr8 threshold.
Signed-off-by: Avi Kivity <avi@redhat.com>
Choose some allowed error values for the cases VMX returned ENOTSUPP so
far as these values could be returned by the KVM_RUN IOCTL.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Now KVM allow guest to modify guest's physical address of EPT's identity mapping page.
(change from v1, discard unnecessary check, change ioctl to accept parameter
address rather than value)
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Use kvm_get_gdt() and kvm_read_ldt() to reduce inline assembly code.
Cc: Avi Kivity <avi@redhat.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Use get_desc_base() and get_desc_limit() to get the base address and
limit in desc_struct.
Cc: Avi Kivity <avi@redhat.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
n_requested_mmu_pages/n_free_mmu_pages are used by
kvm_mmu_change_mmu_pages to calculate the number of pages to zap.
alloc_mmu_pages, called from the vcpu initialization path, modifies this
variables without proper locking, which can result in a negative value
in kvm_mmu_change_mmu_pages (say, with cpu hotplug).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
set_cr3() should already cover the TLB flushing.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Some Linux versions (f8) try to read EOI register that is write only.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Remove kvm_cpu_has_interrupt() and kvm_arch_interrupt_allowed() from
interface between general code and arch code. kvm_arch_vcpu_runnable()
checks for interrupts instead.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
ioeventfd is a mechanism to register PIO/MMIO regions to trigger an eventfd
signal when written to by a guest. Host userspace can register any
arbitrary IO address with a corresponding eventfd and then pass the eventfd
to a specific end-point of interest for handling.
Normal IO requires a blocking round-trip since the operation may cause
side-effects in the emulated model or may return data to the caller.
Therefore, an IO in KVM traps from the guest to the host, causes a VMX/SVM
"heavy-weight" exit back to userspace, and is ultimately serviced by qemu's
device model synchronously before returning control back to the vcpu.
However, there is a subclass of IO which acts purely as a trigger for
other IO (such as to kick off an out-of-band DMA request, etc). For these
patterns, the synchronous call is particularly expensive since we really
only want to simply get our notification transmitted asychronously and
return as quickly as possible. All the sychronous infrastructure to ensure
proper data-dependencies are met in the normal IO case are just unecessary
overhead for signalling. This adds additional computational load on the
system, as well as latency to the signalling path.
Therefore, we provide a mechanism for registration of an in-kernel trigger
point that allows the VCPU to only require a very brief, lightweight
exit just long enough to signal an eventfd. This also means that any
clients compatible with the eventfd interface (which includes userspace
and kernelspace equally well) can now register to be notified. The end
result should be a more flexible and higher performance notification API
for the backend KVM hypervisor and perhipheral components.
To test this theory, we built a test-harness called "doorbell". This
module has a function called "doorbell_ring()" which simply increments a
counter for each time the doorbell is signaled. It supports signalling
from either an eventfd, or an ioctl().
We then wired up two paths to the doorbell: One via QEMU via a registered
io region and through the doorbell ioctl(). The other is direct via
ioeventfd.
You can download this test harness here:
ftp://ftp.novell.com/dev/ghaskins/doorbell.tar.bz2
The measured results are as follows:
qemu-mmio: 110000 iops, 9.09us rtt
ioeventfd-mmio: 200100 iops, 5.00us rtt
ioeventfd-pio: 367300 iops, 2.72us rtt
I didn't measure qemu-pio, because I have to figure out how to register a
PIO region with qemu's device model, and I got lazy. However, for now we
can extrapolate based on the data from the NULLIO runs of +2.56us for MMIO,
and -350ns for HC, we get:
qemu-pio: 153139 iops, 6.53us rtt
ioeventfd-hc: 412585 iops, 2.37us rtt
these are just for fun, for now, until I can gather more data.
Here is a graph for your convenience:
http://developer.novell.com/wiki/images/7/76/Iofd-chart.png
The conclusion to draw is that we save about 4us by skipping the userspace
hop.
--------------------
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Today kvm_io_bus_regsiter_dev() returns void and will internally BUG_ON
if it fails. We want to create dynamic MMIO/PIO entries driven from
userspace later in the series, so we need to enhance the code to be more
robust with the following changes:
1) Add a return value to the registration function
2) Fix up all the callsites to check the return code, handle any
failures, and percolate the error up to the caller.
3) Add an unregister function that collapses holes in the array
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When kvm is in hpet_legacy_mode, the hpet is providing the timer
interrupt and the pit should not be. So in legacy mode, the pit timer
is destroyed, but the *state* of the pit is maintained. So if kvm or
the guest tries to modify the state of the pit, this modification is
accepted, *except* that the timer isn't actually started. When we exit
hpet_legacy_mode, the current state of the pit (which is up to date
since we've been accepting modifications) is used to restart the pit
timer.
The saved_mode code in kvm_pit_load_count temporarily changes mode to
0xff in order to destroy the timer, but then restores the actual
value, again maintaining "current" state of the pit for possible later
reenablement.
[avi: add some reserved storage in the ioctl; make SET_PIT2 IOW]
[marcelo: fix memory corruption due to reserved storage]
Signed-off-by: Beth Kon <eak@us.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We emulate x2apic in software, so host support is not required.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This will save a couple of IPIs.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add tracepoint in msi/ioapic/pic set_irq() functions,
in IPI sending and in the point where IRQ is placed into
apic's IRR.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some Windows versions check whether the BIOS has setup MMI/O for
config space accesses on AMD Fam10h CPUs, we say "no" by returning 0 on
reads and only allow disabling of MMI/O CfgSpace setup by igoring "0" writes.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This reverts commit 6c20e1442bb1c62914bb85b7f4a38973d2a423ba.
To my understanding, it became obsolete with the advent of the more
robust check in mmu_alloc_roots (89da4ff17f). Moreover, it prevents
the conceptually safe pattern
1. set sregs
2. register mem-slots
3. run vcpu
by setting a sticky triple fault during step 1.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Windows 7 tries to update the CPU's microcode on some processors,
so we ignore the MSR write here. The patchlevel register is already handled
(returning 0), because the MSR number is the same as Intel's.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some in-famous OS do unaligned writing for APIC MMIO, and the return value
has been missed in recent change, then the OS hangs.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements MSR interface to local apic as defines by x2apic
Intel specification.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Directed EOI is specified by x2APIC, but is available even when lapic is
in xAPIC mode.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Linux guests will try to enable access to the extended PCI config space
via the I/O ports 0xCF8/0xCFC on AMD Fam10h CPU. Since we (currently?)
don't use ECS, simply ignore write and read attempts.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This changes bus accesses to use high-level kvm_io_bus_read/kvm_io_bus_write
functions. in_range now becomes unused so it is removed from device ops in
favor of read/write callbacks performing range checks internally.
This allows aliasing (mostly for in-kernel virtio), as well as better error
handling by making it possible to pass errors up to userspace.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use slots_lock to protect device list on the bus. slots_lock is already
taken for read everywhere, so we only need to take it for write when
registering devices. This is in preparation to removing in_range and
kvm->lock around it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
switch pit creation to slots_lock. slots_lock is already taken for read
everywhere, so we only need to take it for write when creating pit.
This is in preparation to removing in_range and kvm->lock around it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM will inject a #GP into the guest if that tries to access unhandled
MSRs. This will crash many guests. Although it would be the correct
way to actually handle these MSRs, we introduce a runtime switchable
module param called "ignore_msrs" (defaults to 0). If this is Y, unknown
MSR reads will return 0, while MSR writes are simply dropped. In both cases
we print a message to dmesg to inform the user about that.
You can change the behaviour at any time by saying:
# echo 1 > /sys/modules/kvm/parameters/ignore_msrs
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If the Linux kernel detects an C1E capable AMD processor (K8 RevF and
higher), it will access a certain MSR on every attempt to go to halt.
Explicitly handle this read and return 0 to let KVM run a Linux guest
with the native AMD host CPU propagated to the guest.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Linux tries to disable the flush filter on all AMD K8 CPUs. Since KVM
does not handle the needed MSR, the injected #GP will panic the Linux
kernel. Ignore setting of the HWCR.FFDIS bit in this MSR to let Linux
boot with an AMD K8 family guest CPU.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Correct missing locking in a few places in x86's vm_ioctl handling path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Handle #UD intercept of the sysexit instruction in 64bit mode returning to
32bit compat mode on an AMD host.
Setup the segment descriptors for CS and SS and the EIP/ESP registers
according to the manual.
Signed-off-by: Christoph Egger <christoph.egger@amd.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Handle #UD intercept of the sysenter instruction in 32bit compat mode on
an AMD host.
Setup the segment descriptors for CS and SS and the EIP/ESP registers
according to the manual.
Signed-off-by: Christoph Egger <christoph.egger@amd.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Handle #UD intercept of the syscall instruction in 32bit compat mode on
an Intel host.
Setup the segment descriptors for CS and SS and the EIP/ESP registers
according to the manual. Save the RIP and EFLAGS to the correct registers.
[avi: fix build on i386 due to missing R11]
Signed-off-by: Christoph Egger <christoph.egger@amd.com>
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add the flags needed for syscall, sysenter and sysexit to the opcode table.
Catch (but for now ignore) the opcodes in the emulation switch/case.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Christoph Egger <christoph.egger@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Christoph Egger <christoph.egger@amd.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add the opcodes for syscall, sysenter and sysexit to the list of instructions
handled by the undefined opcode handler.
Signed-off-by: Christoph Egger <christoph.egger@amd.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This allows use of the powerful ftrace infrastructure.
See Documentation/trace/ for usage information.
[avi, stephen: various build fixes]
[sheng: fix control register breakage]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
While trying to get Hyper-V running, I realized that the interrupt injection
mechanisms that are in place right now are not 100% correct.
This patch makes nested SVM's interrupt injection behave more like on a
real machine.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
SVM adds another way to do INVLPG by ASID which Hyper-V makes use of,
so let's implement it!
For now we just do the same thing invlpg does, as asid switching
means we flush the mmu anyways. That might change one day though.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Hyper-V uses some MSRs, some of which are actually reserved for BIOS usage.
But let's be nice today and have it its way, because otherwise it fails
terribly.
[jaswinder: fix build for linux-next changes]
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The host never reads cr2 in process context, so are free to clobber it. The
vmx code does this, so we can safely remove the save/restore code.
Signed-off-by: Avi Kivity <avi@redhat.com>
cr2 changes only rarely, and writing it is expensive. Avoid the costly cr2
writes by checking if it does not already hold the desired value.
Shaves 70 cycles off the vmexit latency.
Signed-off-by: Avi Kivity <avi@redhat.com>
The current code tries to optimize the setting of
KVM_REQ_PENDING_TIMER but used atomic_inc_and_test - which always
returns true unless pending had the invalid value of -1 on entry. This
patch drops the test part preserving the original semantic but
expressing it less confusingly.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Minor issue that likely had no practical relevance: the kvm timer
function so far incremented the pending counter and then may reset it
again to 1 in case reinjection was disabled. This opened a small racy
window with the corresponding VCPU loop that may have happened to run
on another (real) CPU and already consumed the value.
Fix it by skipping the incrementation in case pending is already > 0.
This opens a different race windows, but may only rarely cause lost
events in case we do not care about them anyway (!reinject).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Most of the time IRR is empty, so instead of scanning the whole IRR on
each VM entry keep a variable that tells us if IRR is not empty. IRR
will have to be scanned twice on each IRQ delivery, but this is much
more rare than VM entry.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Replace previous exception with a new one in a hope that instruction
re-execution will regenerate lost exception.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Disable usage of 2M pages if VMX_EPT_2MB_PAGE_BIT (bit 16) is clear
in MSR_IA32_VMX_EPT_VPID_CAP and EPT is enabled.
[avi: s/largepages_disabled/largepages_enabled/ to avoid negative logic]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Handler for EPT misconfiguration which checks for valid state
in the shadow pagetables, printing the spte on each level.
The separate WARN_ONs are useful for kerneloops.org.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This way there is no need to add explicit checks in every
for_each_shadow_entry user.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The performance counter MSRs are different for AMD and Intel CPUs and they
are chosen mainly by the CPUID vendor string. This patch catches writes to
all addresses (regardless of VMX/SVM path) and handles them in the generic
MSR handler routine. Writing a 0 into the event select register is something
we perfectly emulate ;-), so don't print out a warning to dmesg in this
case.
This fixes booting a 64bit Windows guest with an AMD CPUID on an Intel host.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
- Fail early in case gfn_to_pfn returns is_error_pfn.
- For the pre pte write case, avoid spurious "gva is valid but spte is notrap"
messages (the emulation code does the guest write first, so this particular
case is OK).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Under testing, count_writable_mappings returns a value that is 2 integers
larger than what count_rmaps returns.
Suspicion is that either of the two functions is counting a duplicate (either
positively or negatively).
Modifying check_writable_mappings_rmap to check for rmap existance on
all present MMU pages fails to trigger an error, which should keep Avi
happy.
Also introduce mmu_spte_walk to invoke a callback on all present sptes visible
to the current vcpu, might be useful in the future.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Hiding some of the last largepage / level interaction (which is useful
for gbpages and for zero based levels).
Also merge the PT_PAGE_TABLE_LEVEL clearing loop in unlink_children.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Archs are free to use vcpu_id as they see fit. For x86 it is used as
vcpu's apic id. New ioctl is added to configure boot vcpu id that was
assumed to be 0 till now.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We use shadow_pte and spte inconsistently, switch to the shorter spelling.
Rename set_shadow_pte() to __set_spte() to avoid a conflict with the
existing set_spte(), and to indicate its lowlevelness.
Signed-off-by: Avi Kivity <avi@redhat.com>
Since the guest and host ptes can have wildly different format, adjust
the pte accessor names to indicate on which type of pte they operate on.
No functional changes.
Signed-off-by: Avi Kivity <avi@redhat.com>
is_dirty_pte() is used on guest ptes, not shadow ptes, so it needs to avoid
shadow_dirty_mask and use PT_DIRTY_MASK instead.
Misdetecting dirty pages could lead to unnecessarily setting the dirty bit
under EPT.
Signed-off-by: Avi Kivity <avi@redhat.com>
"Unrestricted Guest" feature is added in the VMX specification.
Intel Westmere and onwards processors will support this feature.
It allows kvm guests to run real mode and unpaged mode
code natively in the VMX mode when EPT is turned on. With the
unrestricted guest there is no need to emulate the guest real mode code
in the vm86 container or in the emulator. Also the guest big real mode
code works like native.
The attached patch enhances KVM to use the unrestricted guest feature
if available on the processor. It also adds a new kernel/module
parameter to disable the unrestricted guest feature at the boot time.
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Protect irq injection/acking data structures with a separate irq_lock
mutex. This fixes the following deadlock:
CPU A CPU B
kvm_vm_ioctl_deassign_dev_irq()
mutex_lock(&kvm->lock); worker_thread()
-> kvm_deassign_irq() -> kvm_assigned_dev_interrupt_work_handler()
-> deassign_host_irq() mutex_lock(&kvm->lock);
-> cancel_work_sync() [blocked]
[gleb: fix ia64 path]
Reported-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
None of the interface services the LAPIC emulation provides need to be
exported to modules, and kvm_lapic_get_base is even totally unused
today.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of reloading the pdptrs on every entry and exit (vmcs writes on vmx,
guest memory access on svm) extract them on demand.
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of reading the PDPTRs from memory after every exit (which is slow
and wrong, as the PDPTRs are stored on the cpu), sync the PDPTRs from
memory to the VMCS before entry, and from the VMCS to memory after exit.
Do the same for cr3.
Signed-off-by: Avi Kivity <avi@redhat.com>
vmx_set_cr3() will call vmx_tlb_flush(), which will flush the ept context.
So there is no need to call ept_sync_context() explicitly.
Signed-off-by: Avi Kivity <avi@redhat.com>
We currently publish the i8254 resources to the pio_bus before the devices
are fully initialized. Since we hold the pit_lock, its probably not
a real issue. But lets clean this up anyway.
Reported-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
We modernize the io_device code so that we use container_of() instead of
dev->private, and move the vtable to a separate ops structure
(theoretically allows better caching for multiple instances of the same
ops structure)
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since AMD does not support sysenter in 64bit mode, the VMCB fields storing
the MSRs are truncated to 32bit upon VMRUN/#VMEXIT. So store the values
in a separate 64bit storage to avoid truncation.
[andre: fix amd->amd migration]
Signed-off-by: Christoph Egger <christoph.egger@amd.com>
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The in-kernel speaker emulation is only a dummy and also unneeded from
the performance point of view. Rather, it takes user space support to
generate sound output on the host, e.g. console beeps.
To allow this, introduce KVM_CREATE_PIT2 which controls in-kernel
speaker port emulation via a flag passed along the new IOCTL. It also
leaves room for future extensions of the PIT configuration interface.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM provides a complete virtual system environment for guests, including
support for injecting interrupts modeled after the real exception/interrupt
facilities present on the native platform (such as the IDT on x86).
Virtual interrupts can come from a variety of sources (emulated devices,
pass-through devices, etc) but all must be injected to the guest via
the KVM infrastructure. This patch adds a new mechanism to inject a specific
interrupt to a guest using a decoupled eventfd mechnanism: Any legal signal
on the irqfd (using eventfd semantics from either userspace or kernel) will
translate into an injected interrupt in the guest at the next available
interrupt window.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The problem exists only on VMX. Also currently we skip this step if
there is pending exception. The patch fixes this too.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use proper foo-y style list additions to cleanup all the conditionals,
move module selection after compound object selection and remove the
superflous comment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
