* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap4: Fix UART4 platform data on omap4
omap4: Allow omap_serial_early_init() for OMAP4430 board
omap3: PM: enable UART3 module wakeups
omap2: Fix console serial port number for n8x0
omap2: Fix detection of n8x0
omap1: Fix DSP public peripherals support for ams-delta
omap1: Fix redundant UARTs pin muxing that can break other hardware support
omap: iommu: fix wrong condition check for SUPERSECTION
omap: SDMA: Fix omap_stop_dma() API for channel linking
omap: Fix omap-keypad by restoring old keypad.h without breaking omap2 boards that use matrix_keypad
This patch removes the unnecessary UART4 platform which is under
data is wrong because of this
There is a separate platform structure for UART4
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-By: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables omap_serial_early_init() function for OMAP4430
SDP. Without this the bootup would throw oops in omap_serial_init().
Note that the ifndef CONFIG_ARCH_OMAP4 is split into two sections
to enable omap_serial_early_init(). This ifndef cannot be removed
until omap4 clock framework is implemented.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-By: Tony Lindgren <tony@atomide.com>
Reviewed-By: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART3 is in the PER powerdomain. If PER goes idle/inactive
independently of CORE, for UART3 to wakeup it must have its wakeup
enable bits setup in PM_WKEN_PER. This patch enables these bits.
The reason it works when PER and CORE work together is because when
CORE goes inactive/retention, the IOPAD wakeups are enabled and
trigger UART3 wakeup.
Without this patch, when the UART inactivity timer fires for UART3,
its clocks are disabled and it's unable to wakeup so will be unusable
until PER is awoken by another source.
Another way of testing is by keeping CORE on during suspend but
allowing PER to hit retention
# echo 3 > /debug/pm_debug/core_pwrdm/suspend
then enter suspend
# echo mem > /sys/power/state
Without this patch, UART3 will be unable to wakeup the system.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the recent changes omap serial ports match the physical
numbering like they should. Fix the kernel CMDLINE accordingly
so console works.
Signed-off-by: Tony Lindgren <tony@atomide.com>
DSP public peripherals used to work on OMAP1510 based (or all OMAP1 class?)
machines as long as old dspgateway code were present in the l-o tree. For
several months it is no longer included, breaking support for McBSP1 based
audio on Amstrad Delta, for example.
This patch, derived from the old dspgateway code, corrects the problem for the
board by simply taking the DSP out of reset state, I guess. That way, things
should not break when a new dsp code is added to the tree, and the change can
be reverted then.
If there are any reports on McBSP1 or other DSP public peripherals not working
for other OMAP1 machines (I've not heard of any for now), I can prepare a more
general patch providing an extra include file with a helper function defined.
Created and tested against linux-2.6.32-rc5
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 15ac408ee5 removed enabled_uart
and OMAP_TAG_UART. This works for mach-omap2, but causes issues on
mach-omap1 for some boards as the mach-omap1 serial.c was muxing
pins based on the enabled_uart flag for 15xx.
Fix this by muxing pins in board-*.c files for the 15xx boards for
the uart ports that had enabled_uart flag set before the commit
above.
Tested on Amsdtrad Delta only.
Note that in the future we should add support for powering down
the uarts with a timer like mach-omap2/serial.c does. Otherwise
the enabled uarts will be blocking retention-while-idle.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A bit (2 << 0) is set both on SECTION and SUPERSECTION. To identify
SUPERSECTION correctly, other bits should be compared too.
Reported-by: "Srinivas Pulukuru" <srinivas.pulukuru@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP sDMA driver API omap_stop_dma() doesn't really stop the dma when used
in linking scenario.
The DMA channel needs to be disabled before resetting the chain.
Also fix clearing of the OMAP_DMA_ACTIVE status in the linked case.
Cc: Hari n <hari.zoom@gmail.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Only mach-omap2 boards are currently using matrix_keypad. Allow
mach-omap1 boards to use the old style keypad.h without breaking.
Created against linux-2.6.32-rc5.
Compile tested with omap_3430sdp_defconfig and rx51_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the URL listed for Maverick EP9312 since it is not available
and modify the help text appropriately.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove unnecessary code in ep93xx_gpio_ab_irq_handler().
The desc calculation for gpio port B was left in when the following
commit was merged.
commit d8aa0251f1
Author: Dmitry Baryshkov <dbaryshkov@gmail.com>
Date: Thu Oct 9 13:36:24 2008 +0100
[ARM] 5298/1: Drop desc_handle_irq()
It's not needed so remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove unused prototype for ep93xx_init_time(). This function
is not defined in the kernel.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updates the U300 to use all the drivers merged in during the
2.6.32 merge window.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The macro for the watchdog has been changed from CONFIG_AT91SAM9_WATCHDOG
to CONFIG_AT91SAM9X_WATCHDOG due to AT91CAP9 chips support
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Updating desc for lid keys and resending patch with proper comments:
Define Spitz buttons as GPIO keys in a way compatible with the old driver:
On/Off: As Suspend EV_PWR key
Raw values of lid sensors SWA and SWB: As EV_SW switches
SWA: Display Down
SWB: Lid Closed
Recommended user space decoding:
SWA==0 & SWB==0: lid opened (landscape mode)
SWA==1 & SWB==0: invalid (or mechanic race condition)
SWA==0 & SWB==1: lid closed with display up (portrait mode or mechanic
race condition while closing to display-less mode)
SWA==1 & SWB==1: lid closed with display down (display-less mode)
AK_INT remote trigger is not mapped as input event. Without complete
remote driver and remote pull-up control it has no useful
interpretation.
Signed-off-by: Stanislav Brabec <utx@penguin.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
CM-X300 has libertas on mmc2 and SD card slot on mmc1.
This patch fixes wrong MMC ports assignment.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2xxx clock: set up clockdomain pointer in struct clk
OMAP: Fix race condition with autodeps
omap: McBSP: Fix incorrect receiver stop in omap_mcbsp_stop
omap: Initialization of SDRC params on Zoom2
omap: RX-51: Drop I2C-1 speed to 2200
omap: SDMA: Fixing bug in omap_dma_set_global_params()
omap: CONFIG_ISP1301_OMAP redefined in Beagle defconfig
This patch fixes the BUG: using smp_processor_id() in preemptible
Below is the stripped backtrace.
BUG: using smp_processor_id() in preemptible [00000000] code: init/1
caller is flush_tlb_mm+0x44/0x70
Backtrace:
[<c00225c4>] (dump_backtrace+0x0/0x110) from [<c01713a0>] (dump_stack+0x18/0x1c)
r7:00000000 r6:c00234f0 r5:00000001 r4:c7828000
[<c0171388>] (dump_stack+0x0/0x1c) from [<c0135364>] (debug_smp_processor_id+0xc0/0xf0)
[<c01352a4>] (debug_smp_processor_id+0x0/0xf0) from [<c00234f0>] (flush_tlb_mm+0x44/0x70)
r7:00000000 r6:c60b41a0 r5:c60b4154 r4:00000001
[<c00234ac>] (flush_tlb_mm+0x0/0x70) from [<c0039568>] (dup_mm+0x304/0x38c)
r5:c1f09058 r4:00000000
[<c0039264>] (dup_mm+0x0/0x38c) from [<c0039de4>] (copy_process+0x7b8/0xeb0)
[<c003962c>] (copy_process+0x0/0xeb0) from [<c003a638>] (do_fork+0x15c/0x29c)
[<c003a4dc>] (do_fork+0x0/0x29c) from [<c0021df0>] (sys_clone+0x34/0x3c)
[<c0021dbc>] (sys_clone+0x0/0x3c) from [<c001efa0>] (ret_fast_syscall+0x0/0x2c)
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clock24xx.c is missing a omap2_init_clk_clkdm() in its
omap2_clk_init() function. Among other bad effects, this causes the
OMAP hwmod layer to oops on boot.
Thanks to Carlos Aguiar <carlos.aguiar@indt.org.br> and Stefano
Panella <Stefano.Panella@csr.com> for reporting this bug. Thanks to Tony
Lindgren <tony@atomide.com> for N800 booting advice.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Carlos Aguiar <carlos.aguiar@indt.org.br>
Cc: Stefano Panella <Stefano.Panella@csr.com>
Cc: Tony Lindgren <tony@atomide.com>
There is a possible race condition in clockdomain
code handling hw supported idle transitions.
When multiple autodeps dependencies are being added
or removed, a transition of still remaining dependent
powerdomain can result in false readings of the
state counter. This is especially fatal for off mode
state counter, as it could result in a driver not
noticing a context loss.
Fixed by disabling hw supported state transitions
when autodeps are being changed.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This small typo written by author causes that McBSP receiver is disabled on
OMAP2430 and OMAP3430 even if only transmitter is stopped. This was noted
with ALSA SoC where simultaneous recording halted if playback was stopped
first.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch initializes the correct SDRC settings required
for DVFS on Zoom2.
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C-1 bus frequency on RX-51 should be 2.2 MHz. The speed is limited
by TWL5030/GAIA; a higher speed could lead to errors on the interface. The
maximum speed depends on the system clock for GAIA: 2.2 MHz (if 19.2 MHz),
2.4 MHz (26 MHz) or 2.9 MHz (38.4 MHz).
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Argument tparams was not being used to program
global register GCR.HI_THREAD_RESERVED. This patch fixes the same.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The symbol CONFIG_ISP1301_OMAP was defined twice in the
defconfig. This was causing the warning:
arch/arm/configs/omap3_beagle_defconfig:972:warning:
override: reassigning to symbol ISP1301_OMAP
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a build error due to a typo (missing comma) in:
ARM: 5754/1: ep93xx: update i2c support
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Defines ELF_CORE_COPY_TASK_REGS so that CPU register information
of every thread is included in coredump. Without this, only the faulting
thread is coredumped.
Cc: Roger Quadros <ext-roger.quadros@nokia.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 32-bit wide variant of "mov pc, reg" in Thumb-2 is unpredictable
causing improper handling of the undefined instructions not caught by
the kernel. This patch adds a movw_pc macro for such situations
(currently only used in call_fpe).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The clock name for the watchdog devices was not set consistently
with mx21 on these platforms, resulting in the reset not to work.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mxc_iomux_v3_init() is defined in arch/arm/plat-mxc/iomux-v3.c, which is
not linked for i.MX31 and produces an undefined reference error. Fix this
by building the offending code only for i.MX35.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We have to use mxc_gpio_mode() for the card detection pin
instead of mxc_gpio_setup_multiple_pins() because the latter
does a gpio_request() and thus a later gpio_request() fails.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On ARM, update_mmu_cache() does dcache flush for a page only if
it has a kernel mapping (page_mapping(page) != NULL). The correct
behavior would be to force the flush based on dcache_dirty bit only.
One of the cases where present logic would be a problem is when
a RAM based block device[1] is used as a swap disk. In this case,
we would have in-memory data corruption as shown in steps below:
do_swap_page()
{
- Allocate a new page (if not already in swap cache)
- Issue read from swap disk
- Block driver issues flush_dcache_page()
- flush_dcache_page() simply sets PG_dcache_dirty bit and does not
actually issue a flush since this page has no user space mapping yet.
- Now, if swap disk is almost full, this newly read page is removed
from swap cache and corrsponding swap slot is freed.
- Map this page anonymously in user space.
- update_mmu_cache()
- Since this page does not have kernel mapping (its not in page/swap
cache and is mapped anonymously), it does not issue dcache flush
even if dcache_dirty bit is set by flush_dcache_page() above.
<user now gets stale data since dcache was never flushed>
}
Same problem exists on mips too.
[1] example:
- brd (RAM based block device)
- ramzswap (RAM based compressed swap device)
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PXA27x Errata #37 implies system will hang when switching into or out of
half turbo (HT bit in CLKCFG) mode, workaround this by not using it.
Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net>
Cc: stable-2.6.31 <stable@kernel.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Currently the irq_type field of the csb726_lan_config structure is
initialized twice. The value in the first case,
SMSC911X_IRQ_POLARITY_ACTIVE_LOW, is normally stored in the irq_polarity
field, so I have renamed the field in the first initialization to that.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Seemingly this support was missed when highmem was added, so
DEBUG_HIGHMEM wouldn't have checked the kmap_atomic type.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Bit testing (test, testset, testclear, testchange) for bit numbers
known at compile time returns a word with the tested-for bit set.
Change it to return a true boolean value so to make it consistent with
the out-of-line path and all the other bitops implementations.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make die() better match x86:
- add printing of the last accessed sysfs file
- ensure console_verbose() is called under the lock
- ensure we panic outside of oops_exit()
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dump_mem and dump_backtrace were both using multiple printk statements
to print each line. With DEBUG_LL enabled, this causes OOPS to become
very difficult to read. Solve this by only using one printk per line.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The clock generation system in the ep93xx uses two external oscillator's
and two internal PLLs to derive all the internal clocks. Many of these
internal clocks can be stopped to save power.
This introduces a "parent" hierarchy for the clocks so that the users
count can be correctly tracked for power management.
The "parent" for the video clock can either be one of the PLL outputs
or the external oscillator. In order to correctly track the "parent"
for the video clock calc_clk_div() needed to be modified. It now
returns an error code if the desired rate cannot be generated.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
