Changes in the dt2 branch move stuff around that gets changed
in the drivers/mmc branch. I chose a non-obvious resolution by
adding the new bus-width property into all the tegra sdhci device
nodes.
Conflicts:
arch/arm/boot/dts/tegra-cardhu.dts
arch/arm/boot/dts/tegra-harmony.dts
arch/arm/boot/dts/tegra-ventana.dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.
[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In tegra*.dtsi, set status="disable" for all HW modules that the board
design may choose not to use. Update all boards to specifically enable
any of those modules that are useful by setting status="okay".
This makes board files say which features they do use, rather than which
they don't, which feels more logical. It also makes the .dts files
slightly smaller, at least for existing content.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Sort the nodes according to the following rules:
* First, any overrides for properties or nodes created by included files,
in the order they appeared in the include file.
* Second, any nodes with a reg property, in numerical order.
* Third, any nodes without a reg property, in alphabetical order of node
name.
The second sorting rule at least will probably help if/when we need to
explicitly insert nodes for the various busses in Tegra; that will just
be an indentation change rather than also a node re-ordering.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
DT node names only need to include the unit address if it's required to
make the node name unique. Remove the unnecessary unit addresses.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Ensure that the USB ULPI signals are not tri-stated, and have no pull-
up or pull-down.
Ensure that the pingroup hosting the USB ULPI reset signal (GPIO PV0 or
PV1 depending on the board, so UAC) is not tri-stated, and has no pull-
up or pull-down.
This change appears larger than it is due to the grouping and sorting of
the pin configuration data.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ULPI PHYs have a reset signal, and different boards use a different GPIO
for this task. Add a property to device tree to represent this.
I'm not sure if adding this property to the EHCI controller node is
entirely correct; perhaps eventually we should have explicit separate
nodes for the various PHYs. However, we don't have that right now, so this
binding seems like a reasonable choice.
Cc: <devicetree-discuss@lists.ozlabs.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds a complete pinmux configuration to all Tegra20 device tree
files. This allows removal of board-dt-tegra20.c's use of the pinmux
board files, and the special device tree handling in board-pinmux.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
The Tegra PMC (Power Management Controller) interfaces with an external
PMU (Power Management Unit), and controls wake-up from sleep modes.
This initial binding is the bare minimum required to control the PMC's
inversion of the PMU's interrupt signal.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add complete bindings to instantiate and configure the codec and
top-level audio complex on all currently supported boards using the
Tegra+WM8903 audio driver.
On those boards, disable the I2S2 controller since it isn't used.
On boards not using the WM8903 codec, disable all the audio devices;
they can be re-enabled once the relevant codec and ASoC machine drivers
have been ported to device-tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Mark any SDHCI controllers that aren't registered by the board files as
disabled in the device-tree files.
In practice, these controllers:
* Have nothing hooked up to them at all, or
* For ports intended for SDIO usage, the drivers for anything that might
be attached are not in the device-tree yet. If/when drivers appear, the
SD/MMC port can be re-enabled.
The only possible exception is TrimSlice's mico SD slot, but that wasn't
enabled in the board files before anyway, and doesn't work when all the
SDHCI controllers are enabled anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Mark any serial ports that aren't registered by the board files as disabled
in the device-tree files.
In practice, none of the now-disabled ports ended up succeeding device
probing because of the missing clock-frequency property. However,
explicitly marking the devices disabled has the advantage of squashing
the dev_warn() the failed probe causes, and documenting that we intend
the port not to be used, rather than accidentally left out the property.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The command-lines present in the existing /chosen node are not necessarily
correct for all users. Ideally, we should simply use the command-line
supplied by the boot-loader.
In fact, using the boot-loader's cmdline is quite easy; either the
bootloader fully supports DT, in which case it can modify the DT passed
to the kernel to include its command-line, or CONFIG_APPENDED_DTB can
be used in conjunction with CONFIG_ARM_ATAG_DTB_COMPAT, and the kernel
will substitute the bootloader's command-line into the DT.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
There are no drivers in the kernel at present which can make use of the
memory reserved by /memreserve/, so there is no point reserving it. Remove
/memreserve/ to allow the user more memory. It's also unclear whether any
future driver would actually require /memreserve/, or allocate memory
through some other mechanism.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
For Seaboard's internal eMMC, this makes the difference between a
5.5MB/s and 10.2MB/s transfer rate. On Harmony, there wasn't any
measurable difference on my cheap/slow ~2MB/s card.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The bindings were recently updated to have separate properties for each
type of GPIO. Update the Device Tree source to match that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Everything required to populate NVIDIA Tegra devices from the device
tree. This patch adds a new DT_MACHINE_DESC() which matches against
a tegra20 device tree. So far it only registers the on-chip devices,
but it will be refined in follow on patches to configure clocks and
pin IO from the device tree also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
