PCI devices support two variants of the D3 power state: D3hot (main power
present) D3cold (main power removed). Previously struct pci_dev contained:
unsigned int d3_delay; /* D3->D0 transition time in ms */
unsigned int d3cold_delay; /* D3cold->D0 transition time in ms */
"d3_delay" refers specifically to the D3hot state. Rename it to
"d3hot_delay" to avoid ambiguity and align with the ACPI "_DSM for
Specifying Device Readiness Durations" in the PCI Firmware spec r3.2,
sec 4.6.9.
There is no change to the functionality.
Link: https://lore.kernel.org/r/20200730210848.1578826-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI_DEV_FLAGS_NO_D3 should not be used outside of PCI core.
Instead, we can use pci_save_state() to hint PCI core that the device
should stay at D0 during suspend. By doing so, PCI core will let the
upstream bridges also stays at D0 so the entire hierarchy is in the
correct power state as PCI spec mandates.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added Tiger Lake PCI device ID to the supported device list.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Comet Lake H into ishtp support list.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
EHL is a new platform using ishtp solution, add its device id
to support list.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The NO_D3 flag would be set if the ISH enter D0i3 in ish_suspend(),
The resume paths can be distinguished by checking the NO_D3 flag.
It's more reasonable than checking the FW status.
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For suspend-to-idle, send suspend message and set N0_D3 flag to put
the ISH into D0i3 state.
For suspend-to-mem, disable the DMA bit before ISH entering D3, and
NO_D3 flag is cleared by default, then the ISH would enter D3.
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, the NO_D3 flag is set in ish_probe(), and cleared in
ish_remove(). So even if the system goes into S3, ISH is still
in D0i3 state. It makes more sense that put ISH into D3 as system
goes into S3 and put ISH into D0i3 as system goes into suspend-to-idle.
I remove the NO_D3 setting in ish_probe(), so that ISH can enter
D3 state when system enters S3. Only set N0_D3 flag when system
enters the suspend-to-idle or platform specified, and clear it
when system resume.
When the ISH enters D3, the FW will check the DMA bit status.
If the DMA bit is set, the FW will reset automatically. So the
DMA bit need be clear before putting ISH into D3 state.
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove the NO_D3 flag when remove the driver and let device enter
into D3, it will save more power.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Comet Lake PCI device ID to the supported device list.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reading of IPC_REG_ISH_HOST_FWSTS will flush both message register
and doorbell. So move the doorbell write before reading of
IPC_REG_ISH_HOST_FWSTS.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Tested-by: Hongyan Song <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently we are using one additional static variable and a spinlock to
prevent contention of writing IPC messages to ISH hardware, which is
not necessary. Once ISH is ready to accept new data, we can push new
data to hardware. This pushing of new data is already protected by
wr_processing_spinlock for contention, which is enough. So use this
spinlock to check both readiness for accepting new data and once ready
allow writing of ipc message from queue to ISH hardware.
While here, cleaned up some space after return.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Tested-by: Hongyan Song <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Host driver should handle interrupt mask register earlier than wake up ish FW
else there will be conditions when FW interrupt comes, host PIMR register still
not set ready, so move the interrupt mask setting before ish_wakeup.
Clear PISR busy_clear bit in ish_irq_handler. If not clear, there will be
conditions host driver received a busy_clear interrupt (before the busy_clear
mask bit is ready), it will return IRQ_NONE after check_generated_interrupt,
the interrupt will never be cleared, causing the DEVICE not sending following
IRQ.
Since PISR clear should not be called for the CHV device we do this change.
After the change, both ISH2HOST interrupt and busy_clear interrupt will be
considered as interrupt from ISH, busy_clear interrupt will return IRQ_HANDLED
from IPC_IS_BUSY check.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now ish hid ipc only support sideband interrupt but on some platforms
they use MSI interrupt.
In order to make the interrupt type coverage all the scenario add
single MSI interrupt support, it can match all interrupt types.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added PCI ID for Ice Lake mobile platform.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently wr_msg_ctl_info is used in ishtp_device just for list head
purpose, using list_head directly can save ~150 bytes size for
each replacement.
Also this patch can save ~170 bytes of code size in intel-ish-ipc.ko.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use resource-managed api to simplify error handling in probe and
driver remove logic.
With this patch, we can save ~170 bytes code size in intel-ish-ipc.ko.
before:
text data bss dec hex filename
11495 1568 72 13135 334f intel-ish-ipc.ko
after:
text data bss dec hex filename
11327 1568 72 12967 32a7 intel-ish-ipc.ko
Signed-off-by: Hong Liu <hong.liu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ish_dev_init() allocates 512*176 bytes memory for tx_buf and stores it at
&dev->wr_free_list_head.link list on ish_probe().
But there is no deallocation of this memory in ish_remove() and in
ish_probe() error path.
So current intel-ish-ipc provides 88 KB memory leak for each
probe/release.
The patch replaces kzalloc allocation by devm_kzalloc and removes
ishtp_device *dev deallocation by kfree.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On Mehlow Xeon-E workstation, ISH PCI device is enabled but without ISH
firmware. Here the ISH device PCI device id was reused for some non Linux
storage drivers. So this was not done for enabling ISH. But this has a
undesirable side effect for Linux.
Here the ISH driver will be loaded via PCI enumeration and will try to do
reset sequence. But reset sequence will wait till timeout as there is no
real ISH firmware is present to take action. This delay will add to boot
time of Linux (This platform will still continue to boot after this
timeout).
To avoid this boot delay we need to prevent loading of ISH drivers on
this platform. So we need to have hack to avoid treating this device as
ISH on this platform. To identify this workstation, we need some runtime
method. Luckily there are special PCI id on this workstation to
distinguish from the client version of this platform. On client version,
the ISH is supported using same PCI device id. So this change look for
the presence of PCI device IDs A309 and A30A and exit.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current ISH driver only registers suspend/resume PM callbacks which don't
support hibernation (suspend to disk). Basically after hiberation, the ISH
can't resume properly and user may not see sensor events (for example: screen
rotation may not work).
User will not see a crash or panic or anything except the following message
in log:
hid-sensor-hub 001F:8086:22D8.0001: timeout waiting for response from ISHTP device
So this patch adds support for S4/hiberbation to ISH by using the
SIMPLE_DEV_PM_OPS() MACRO instead of struct dev_pm_ops directly. The suspend
and resume functions will now be used for both suspend to RAM and hibernation.
If power management is disabled, SIMPLE_DEV_PM_OPS will do nothing, the suspend
and resume related functions won't be used, so mark them as __maybe_unused to
clarify that this is the intended behavior, and remove #ifdefs for power
management.
Cc: stable@vger.kernel.org
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added PCI ID for Cannon Lake and Coffee Lake laptop/desktop skews.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added PCI ID for Gemini Lake ISH.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added PCI ID for Cannon Lake ISH.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The internal accounting uses 'timespec' based time stamps, which is
slightly inefficient and also problematic once we get to the time_t
overflow in 2038.
When communicating to the firmware, we even get an open-coded 64-bit
division that prevents the code from being build-tested on 32-bit
architectures and is inefficient due to the double conversion from
64-bit nanoseconds to seconds+nanoseconds and then microseconds.
This changes the code to use ktime_t instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For ISH resume, there are two paths, they need different way to handle: one
where ISH is not powered off, in that case a simple resume message is enough,
in other case we need a reset sequence.
We can use ISH FW status to distinguish those two cases and handle them
properly.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Structure ishtp_device contains a logging function, print_log(), which
formats some of its parameters using vsnprintf(). Add a __printf
attribute to this function field (and to ish_event_tracer()) in order to
detect at compile time issues related to the printf-like formatting.
While at it, make format parameter a const pointer as print_log() is not
supposed to modify it.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid/intel-ish-hid does not use any miscdevice so this patch remove
this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
set_current_task() must be called before schedule_timeout(), for this
driver, in order to avoid incorrect usage, use msleep_interrupt()
instead.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The macro timed_wait_for_timeout() only be used in one function, so move
this marco from header file and change it to a function in ipc.c, where
it is used.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The macro timed_wait_for() in utils.h isn't used in current ipc
driver, so remove it for avoiding confusion.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ts_format.reserved is not used anywhere yet, but the compiler generates a
warning when the struct's (uninitialized) field is being copied around
drivers/hid/intel-ish-hid/ipc/ipc.c: In function ‘write_ipc_from_queue’:
drivers/hid/intel-ish-hid/ipc/ipc.c:316: warning: ‘ts_format.reserved’ may be used uninitialized in this function
Avoid this by force-initializing the field to zero.
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On some platforms ISH interrupt is shared, which causes request_irq to
fail. This requires IRQF_SHARED irq flag.
But IRQF_NO_SUSPEND and IRQF_SHARED should not be used together, so
removed IRQF_NO_SUSPEND flag. Anyway this driver doesn't require
IRQF_NO_SUSPEND, as this interrupt is not required during "noirq" phases
of suspending and resuming devices as well as during the time when
nonboot CPUs are taken offline and brought back online.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When built as a module, modprobe followed by rmmod can fail because
DMA was still active. So to fix this, DMA needs to be disabled during
module exit.
This change disables DMA during modules exit and change the ISH PCI
device status to D3.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a new function ish_disable_dma() and move DMA disable operations
here, so that this functionality can be reused.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Same operations are done in ish_hw_start() and _ish_hw_reset() to
wakeup ISH device. Consolidate them by introducing a new function
ish_wakeup() and move the code there.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix
drivers/hid/intel-ish-hid/ipc/pci-ish.c:247:12: warning: ‘ish_suspend’ defined but not used [-Wunused-function]
static int ish_suspend(struct device *device)
^
drivers/hid/intel-ish-hid/ipc/pci-ish.c:282:12: warning: ‘ish_resume’ defined but not used [-Wunused-function]
static int ish_resume(struct device *device)
^
by sticking them in the CONFIG_PM range too.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-input@vger.kernel.org
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This layer is responsible for
- Enumerating over PCI bus
- Inform FW about host readiness
- Provide HW interface to transport layer for control and messages
- Interrupt handling and routing
Original-author: Daniel Drubin <daniel.drubin@intel.com>
Reviewed-and-tested-by: Ooi, Joyce <joyce.ooi@intel.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Rann Bar-On <rb6@duke.edu>
Tested-by: Atri Bhattacharya <badshah400@aim.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
