When an EEH error occurs, the device/slot is disconnected. This condition
is more reliably detected (i.e., returns all ones) with an MMIO read rather
than a config read -- especially on power platforms.
Hence, this patch fixes EEH error detection by replacing config reads with
MMIO reads for reading the error registers. The error registers in
Skyhawk-R/BE2/BE3 are accessible both via the config space and the
PCICFG (BAR0) memory space.
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing this cmd for more than 8 EQs does not have the intended effect
even on BEx and Skyhawk-R.
This patch fixes this by issuing this cmd for upto 8 EQs at a time.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a PF does not restrict its VF interface from enabling vlan
promiscuous mode. This breaks vlan isolation when a vlan
(transparent tagging) is configured on a VF.
This patch fixes this problem by disabling the vlan promisc capability
for VFs.
Reported-by: Yoann Juet <veilletechno-irts@univ-nantes.fr>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_send_fin() does not account for the memory it allocates properly, so
sk_forward_alloc can be negative in cases where we've sent a FIN:
ss example output (ss -amn | grep -B1 f4294):
tcp FIN-WAIT-1 0 1 192.168.0.1:45520 192.0.2.1:8080
skmem:(r0,rb87380,t0,tb87380,f4294966016,w1280,o0,bl0)
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for throw routes to trigger evaluation of other policy rules
EAGAIN needs to be propagated up to fib_rules_lookup
similar to how its done for IPv4
A simple testcase for verification is:
ip -6 rule add lookup 33333 priority 33333
ip -6 route add throw 2001:db8::1
ip -6 route add 2001:db8::1 via fe80::1 dev wlan0 table 33333
ip route get 2001:db8::1
Signed-off-by: Steven Barth <cyrus@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Grant reported frequent crashes in ipv6_select_ident when
udp6_ufo_fragment is called from openvswitch on a skb that doesn't
have a dst_entry set.
ipv6_proxy_select_ident generates the frag_id without using the dst
associated with the skb. This approach was suggested by Vladislav
Yasevich.
Fixes: 0508c07f5e ("ipv6: Select fragment id during UFO segmentation if not set.")
Cc: Vladislav Yasevich <vyasevic@redhat.com>
Reported-by: Matt Grant <matt@mattgrant.net.nz>
Tested-by: Matt Grant <matt@mattgrant.net.nz>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the current netback, the bandwidth limiter's parameters are only
settable during vif setup time. This patch register a watch on them, and
thus makes them runtime changeable.
When the watch fires, the timer is reset. The timer's mutex is used for
fencing the change.
Cc: Anthony Liguori <aliguori@amazon.com>
Signed-off-by: Imre Palik <imrep@amazon.de>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
inet: tcp listener refactoring part 14
OK, we have serious patches here.
We get rid of the central timer handling SYNACK rtx,
which is killing us under even medium SYN flood.
We still use the listener specific hash table.
This will be done in next round ;)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_ack_backlog & sk_max_ack_backlog were 16bit fields, meaning
listen() backlog was limited to 65535.
It is time to increase the width to allow much bigger backlog,
if admins change /proc/sys/net/core/somaxconn &
/proc/sys/net/ipv4/tcp_max_syn_backlog default values.
Tested:
echo 5000000 >/proc/sys/net/core/somaxconn
echo 5000000 >/proc/sys/net/ipv4/tcp_max_syn_backlog
Ran a SYNFLOOD test against a listener using listen(fd, 5000000)
myhost~# grep request_sock_TCP /proc/slabinfo
request_sock_TCP 4185642 4411940 304 13 1 : tunables 54 27 8 : slabdata 339380 339380 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the major issue for TCP is the SYNACK rtx handling,
done by inet_csk_reqsk_queue_prune(), fired by the keepalive
timer of a TCP_LISTEN socket.
This function runs for awful long times, with socket lock held,
meaning that other cpus needing this lock have to spin for hundred of ms.
SYNACK are sent in huge bursts, likely to cause severe drops anyway.
This model was OK 15 years ago when memory was very tight.
We now can afford to have a timer per request sock.
Timer invocations no longer need to lock the listener,
and can be run from all cpus in parallel.
With following patch increasing somaxconn width to 32 bits,
I tested a listener with more than 4 million active request sockets,
and a steady SYNFLOOD of ~200,000 SYN per second.
Host was sending ~830,000 SYNACK per second.
This is ~100 times more what we could achieve before this patch.
Later, we will get rid of the listener hash and use ehash instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When request sock are put in ehash table, the whole notion
of having a previous request to update dl_next is pointless.
Also, following patch will get rid of big purge timer,
so we want to delete a request sock without holding listener lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Round up min_size respectively round down max_size to the next power
of two to make sure we always respect the limit specified by the
user. This is required because we compare the table size against the
limit before we expand or shrink.
Also fixes a minor bug where we modified min_size in the params
provided instead of the copy stored in struct rhashtable.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input updates from Dmitry Torokhov:
"An update to Synaptics driver that makes it usable with the 2015
lineup from Lenovo"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - use dmax in input_mt_assign_slots"
Input: synaptics - remove X250 from the topbuttonpad list
Input: synaptics - remove X1 Carbon 3rd gen from the topbuttonpad list
Input: synaptics - re-route tracksticks buttons on the Lenovo 2015 series
Input: synaptics - remove TOPBUTTONPAD property for Lenovos 2015
Input: synaptics - retrieve the extended capabilities in query $10
Input: synaptics - do not retrieve the board id on old firmwares
Input: synaptics - handle spurious release of trackstick buttons
Input: synaptics - fix middle button on Lenovo 2015 products
Input: synaptics - skip quirks when post-2013 dimensions
Input: synaptics - support min/max board id in min_max_pnpid_table
Input: synaptics - remove obsolete min/max quirk for X240
Input: synaptics - query min dimensions for fw v8.1
Input: synaptics - log queried and quirked dimension values
Input: synaptics - split synaptics_resolution(), query first
Pull overlayfs fixes from Miklos Szeredi:
"This fixes minor issues with the multi-layer update in v4.0"
* 'overlayfs-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: upper fs should not be R/O
ovl: check lowerdir amount for non-upper mount
ovl: print error message for invalid mount options
- Fix up consumer return values on pin control stubs.
- Four patches fixing up the interrupt handling and
sleep context save in the Baytrail driver.
- Make default output directions work properly in the
Cherryview driver.
- Fix interrupt locking in the AT91 driver.
- Fix setting interrupt generating lines as input in
the sunxi driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qp0z
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a slew of pin control fixes I've accumulated for the v4.0
kernel. Nothing special, just driver fixes (mainly embedded Intel it
seems) and a misunderstanding regarding the stub functions was
reverted:
- Fix up consumer return values on pin control stubs.
- Four patches fixing up the interrupt handling and sleep context
save in the Baytrail driver.
- Make default output directions work properly in the Cherryview
driver.
- Fix interrupt locking in the AT91 driver.
- Fix setting interrupt generating lines as input in the sunxi
driver"
* tag 'pinctrl-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sun4i: GPIOs configured as irq must be set to input before reading
pinctrl: at91: move lock/unlock_as_irq calls into request/release
pinctrl: update direction_output function of cherryview driver
pinctrl: baytrail: Save pin context over system sleep
pinctrl: baytrail: Rework interrupt handling
pinctrl: baytrail: Clear interrupt triggering from pins that are in GPIO mode
pinctrl: baytrail: Relax GPIO request rules
Revert "pinctrl: consumer: use correct retval for placeholder functions"
Quit complaining about a couple of events that we actually expect to see
during an NVM update.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull IDE fix from David Miller:
"Just one fix to convert a by-hand conversion of jiffies to msecs, from
Nicholas McGuire"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide_tape: convert jiffies with jiffies_to_msecs
Pull sparc fixes from David Miller:
1) Some command cases of semtimedop() not even handled due to miscoded
comparison on sparc64. From Rob Gardner.
2) Due to two bugs, /proc/kcore wan't working properly on sparc.
3) Make sure fatal traps stop all running cpus, from Dave Kleikamp.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Fix /proc/kcore
sparc: semtimedop() unreachable due to comparison error
sparc: io_64.h: Replace io function-link macros
sparc64: fatal trap should stop all cpus
arch: sparc: kernel: starfire.c: Remove unused function
arch: sparc: kernel: traps_64.c: Remove some unused functions
We can't directly call ipv6_sock_mc_join() but should use the stub
instead and protect it around IS_ENABLED.
Fixes: d0f91938be ("tipc: add ip/udp media type")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai says:
====================
Add Device ID and make device ID table const
This patch series adds new device ID and makes device ID table const
The patches series is created against 'net-next' tree.
And includes patches on cxgb4 and csiostor driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make PCI Device ID Tables be "const" to move them out of the data segment and
remove a redundant check on CH_PCI_DEVICE_ID_TABLE_DEFINE_BEGIN in
t4_pci_id_tbl.h to guard the contents of the include file.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-19
This wont the last 4.1 bluetooth-next pull request, but we've piled up
enough patches in less than a week that I wanted to save you from a
single huge "last-minute" pull somewhere closer to the merge window.
The main changes are:
- Simultaneous LE & BR/EDR discovery support for HW that can do it
- Complete LE OOB pairing support
- More fine-grained mgmt-command access control (normal user can now do
harmless read-only operations).
- Added RF power amplifier support in cc2520 ieee802154 driver
- Some cleanups/fixes in ieee802154 code
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix packet header offset calculation in _decode_session6(), from
Hajime Tazaki.
2) Fix route leak in error paths of xfrm_lookup(), from Huaibin Wang.
3) Be sure to clear state properly when scans fail in iwlwifi mvm code,
from Luciano Coelho.
4) iwlwifi tries to stop scans that aren't actually running, also from
Luciano Coelho.
5) mac80211 should drop mesh frames that are not encrypted, fix from
Bob Copeland.
6) Add new device ID to b43 wireless driver for BCM432228 chips, from
Rafał Miłecki.
7) Fix accidental addition of members after variable sized array in
struct tc_u_hnode, from WANG Cong.
8) Don't re-enable interrupts until after we call napi_complete() in
ibmveth and WIZnet drivers, frm Yongbae Park.
9) Fix regression in vlan tag handling of fec driver, from Fugang Duan.
10) If a network namespace change fails during rtnl_newlink(), we don't
unwind the device registry properly.
11) Fix two TCP regressions, from Neal Cardwell:
- Don't allow snd_cwnd_cnt to accumulate huge values due to missing
test in tcp_cong_avoid_ai().
- Restore CUBIC back to advancing cwnd by 1.5x packets per RTT.
12) Fix performance regression in xne-netback involving push TX
notifications, from David Vrabel.
13) __skb_tstamp_tx() can be called with a NULL sk pointer, do not
dereference blindly. From Willem de Bruijn.
14) Fix potential stack overflow in RDS protocol stack, from Arnd
Bergmann.
15) VXLAN_VID_MASK used incorrectly in new remote checksum offload
support of VXLAN driver. Fix from Alexey Kodanev.
16) Fix too small netlink SKB allocation in inet_diag layer, from Eric
Dumazet.
17) ieee80211_check_combinations() does not count interfaces correctly,
from Andrei Otcheretianski.
18) Hardware feature determination in bxn2x driver references a piece of
software state that actually isn't initialized yet, fix from Michal
Schmidt.
19) inet_csk_wait_for_connect() needs a sched_annotate_sleep()
annoation, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
Revert "net: cx82310_eth: use common match macro"
net/mlx4_en: Set statistics bitmap at port init
IB/mlx4: Saturate RoCE port PMA counters in case of overflow
net/mlx4_en: Fix off-by-one in ethtool statistics display
IB/mlx4: Verify net device validity on port change event
act_bpf: allow non-default TC_ACT opcodes as BPF exec outcome
Revert "smc91x: retrieve IRQ and trigger flags in a modern way"
inet: Clean up inet_csk_wait_for_connect() vs. might_sleep()
ip6_tunnel: fix error code when tunnel exists
netdevice.h: fix ndo_bridge_* comments
bnx2x: fix encapsulation features on 57710/57711
mac80211: ignore CSA to same channel
nl80211: ignore HT/VHT capabilities without QoS/WMM
mac80211: ask for ECSA IE to be considered for beacon parse CRC
mac80211: count interfaces correctly for combination checks
isdn: icn: use strlcpy() when parsing setup options
rxrpc: bogus MSG_PEEK test in rxrpc_recvmsg()
caif: fix MSG_OOB test in caif_seqpkt_recvmsg()
bridge: reset bridge mtu after deleting an interface
can: kvaser_usb: Fix tx queue start/stop race conditions
...
Erik Hugne says:
====================
tipc: small bugfix an support for datagram connect()
Most notable in this series is patch#3 that allows programs to associate
a tipc address with a connectionless (RDM/DGRAM) socket.
v2: Fix indent issue in patch#3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the example of ip4_datagram_connect, we store the
address in the socket structure for dgram/rdm sockets and use
that as the default destination for subsequent send() calls.
It is allowed to connect to any address types, and the behaviour
of send() will be the same as a normal sendto() with this address
provided. Binding to an AF_UNSPEC address clears the association.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 1186adf7df ("tipc: simplify message forwarding and
rejection in socket layer") -EHOSTUNREACH is propagated back to
the sending process if we fail to deliver the message to another
socket local to the node.
This is wrong, host unreachable should only be reported when the
destination port/name does not exist in the cluster, and that
check is always done before sending the message. Also, this
introduces inconsistent sendmsg() behavior for local/remote
destinations. Errors occurring on the receiving side should not
trickle up to the sender. If message delivery fails TIPC should
either discard the packet or reject it back to the sender based
on the destination droppable option.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_node_remove_conn may be called twice if shutdown() is
called on a socket that have messages in the receive queue.
Calling this function twice does no harm, but is unnecessary
and we remove the redundant call.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The misc subsystem (which is used for /dev/fuse) initializes private_data to
point to the misc device when a driver has registered a custom open file
operation, and initializes it to NULL when a custom open file operation has
*not* been provided.
This subtle quirk is confusing, to the point where kernel code registers
*empty* file open operations to have private_data point to the misc device
structure. And it leads to bugs, where the addition or removal of a custom open
file operation surprisingly changes the initial contents of a file's
private_data structure.
So to simplify things in the misc subsystem, a patch [1] has been proposed to
*always* set the private_data to point to the misc device, instead of only
doing this when a custom open file operation has been registered.
But before this patch can be applied we need to modify drivers that make the
assumption that a misc device file's private_data is initialized to NULL
because they didn't register a custom open file operation, so they don't rely
on this assumption anymore. FUSE uses private_data to store the fuse_conn and
errors out if this is not initialized to NULL at mount time.
Hence, we now set a file's private_data to NULL explicitly, to be independent
of whatever value the misc subsystem initializes it to by default.
[1] https://lkml.org/lkml/2014/12/4/939
Reported-by: Giedrius Statkevicius <giedriuswork@gmail.com>
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Tom Van Braeckel <tomvanbraeckel@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
The current error-path code (when gpiod_get_index() reports
an error) can never free pwrseq->reset_gpios[0], but might
try to tree pwrseq->reset_gpios[-1], which has unfortunate
consequences.
Signed-off-by: NeilBrown <neil@brown.name>
Fixes: 934f1f4833
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Use jiffies_to_msecs for converting jiffies as it handles all of the corner
cases reliably and also helps readability. The printk format is fixed up
as jiffies_to_msecs returns unsigned int not unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a networking device is taken down that has a non-trivial number
of VLAN devices configured under it, we eat a full synchronize_net()
for every such VLAN device.
This is because of the call chain:
NETDEV_DOWN notifier
--> vlan_device_event()
--> dev_change_flags()
--> __dev_change_flags()
--> __dev_close()
--> __dev_close_many()
--> dev_deactivate_many()
--> synchronize_net()
This is kind of rediculous because we already have infrastructure for
batching doing operation X to a list of net devices so that we only
incur one sync.
So make use of that by exporting dev_close_many() and adjusting it's
interfaace so that the caller can fully manage the batch list. Use
this in vlan_device_event() and all the overhead goes away.
Reported-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a large hash table, we can easily spend seconds to
walk over all entries. Add a cond_resched() to yield
cpu if necessary.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 11ad714b98 because
it breaks cx82310_eth.
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the phys_port_name operation. Port names are pulled from the
rocker hardware model in qemu and default to the qemu name + port id.
e.g.,
sw1p1: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:12:35:01 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
where 'sw1' comes from the qemu command line -device rocker,name=sw1, and
'p1' is port 1.
Patch is adapted from Scott's phys_port_id patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to port id allow netdevices to specify port names and export
the name via sysfs. Drivers can implement the netdevice operation to
assist udev in having sane default names for the devices using the
rule:
$ cat /etc/udev/rules.d/80-net-setup-link.rules
SUBSYSTEM=="net", ACTION=="add", ATTR{phys_port_name}!="",
NAME="$attr{phys_port_name}"
Use of phys_name versus phys_id was suggested-by Jiri Pirko.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/kcore investigates the "System RAM" elements in /proc/iomem to
initialize it's memory tables. Therefore we have to register them
before it tries to do so. kcore uses device_initcall() so let's
use arch_initcall() for the registry.
Also we need ARCH_PROC_KCORE_TEXT to get the virtual addresses of
the kernel image correct.
Reported-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if a multicast join operation fail, the vxlan interface will
be UP but not functional, without even a log message informing the user.
Now that we can grab socket lock after already having rntl, we don't
need to defer socket creation and multicast operations. By not deferring
we can do proper error reporting to the user through ip exit code.
This patch thus removes all deferred work that vxlan had and put it back
inline. Now the socket will only be created, bound and join multicast
group when one bring the interface up, and will undo all that as soon as
one put the interface down.
As vxlan_sock_hold() is not used after this patch, it was removed too.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in favor of their inner __ ones, which doesn't grab rtnl.
As these functions need to operate on a locked socket, we can't be
grabbing rtnl by then. It's too late and doing so causes reversed
locking.
So this patch:
- move rtnl handling to callers instead while already fixing some
reversed locking situations, like on vxlan and ipvs code.
- renames __ ones to not have the __ mark:
__ip_mc_{join,leave}_group -> ip_mc_{join,leave}_group
__ipv6_sock_mc_{join,drop} -> ipv6_sock_mc_{join,drop}
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some setsockopt operations in ipv4 and ipv6 that are grabbing
rtnl after having grabbed the socket lock. Yet this makes it impossible
to do operations that have to lock the socket when already within a rtnl
protected scope, like ndo dev_open and dev_stop.
We normally take coarse grained locks first but setsockopt inverted that.
So this patch invert the lock logic for these operations and makes
setsockopt grab rtnl if it will be needed prior to grabbing socket lock.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
inet: tcp listener refactoring, part 13
inet_hash functions are in a bad state : Too much IPv6/IPv4 copy/pasting.
Lets refactor a bit.
Idea is that we do not want to have an equivalent of inet_csk(sk)->icsk_af_ops
for request socks in order to be able to use the right variant.
In this patch series, I started to let IPv6/IPv4 converge to common helpers.
Idea is to use ipv6_addr_set_v4mapped() even for AF_INET sockets, so that
we can test
if (sk->sk_family == AF_INET6 &&
!ipv6_addr_v4mapped(&sk->sk_v6_daddr))
to tell if we deal with an IPv6 socket, or IPv4 one, at least in slow paths.
Ideally, we could save 8 bytes per struct sock_common, if we
alias skc_daddr & skc_rcv_saddr to skc_v6_daddr[3]/skc_v6_rcv_saddr[3].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be able to use sk_ehashfn() for request socks,
we need to initialize their IPv6/IPv4 addresses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now always call __inet_hash_nolisten(), no need to pass it
as an argument.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
