HS400/HS200/eMMC HS doesn't have Preset Value register.
Hence, sdhci_set_ios function overrides the value set by fmw to
SDHCI_CTRL_DRV_TYPE_B.
This patch sets drv_type to MMC_SET_DRIVER_TYPE_A
so that host_control2 register gets updated with the required
strength value.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200623133347.4598-1-akshu.agrawal@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Add support for host software queue for (e)MMC/SD
- Throttle polling rate for CMD6
- Update CMD13 busy condition check for CMD6 commands
- Improve busy detect polling for erase/trim/discard/HPI
- Fixup support for HW busy detection for HPI commands
- Re-work and improve support for eMMC sanitize commands
MMC host:
- mmci: Add support for sdmmc variant revision 2.0
- mmci_sdmmc: Improve support for busyend detection
- mmci_sdmmc: Fixup support for signal voltage switch
- mmci_sdmmc: Add support for tuning with delay block
- mtk-sd: Fix another SDIO irq issue
- sdhci: Disable native card detect when GPIO based type exist
- sdhci: Add option to defer request completion
- sdhci_am654: Add support to set a tap value per speed mode
- sdhci-esdhc-imx: Add support for i.MX8MM based variant
- sdhci-esdhc-imx: Fixup support for standard tuning on i.MX8 usdhc
- sdhci-esdhc-imx: Optimize for strobe/clock dll settings
- sdhci-esdhc-imx: Fixup support for system and runtime suspend/resume
- sdhci-iproc: Update regulator/bus-voltage management for bcm2711
- sdhci-msm: Prevent clock gating with PWRSAVE_DLL on broken variants
- sdhci-msm: Fix management of CQE during SDHCI reset
- sdhci-of-arasan: Add support for auto tuning on ZynqMP based platforms
- sdhci-omap: Add support for system suspend/resume
- sdhci-sprd: Add support for HW busy detection
- sdhci-sprd: Enable support host software queue
- sdhci-tegra: Add support for HW busy detection
- tmio/renesas_sdhi: Enforce retune after runtime suspend
- renesas_sdhi: Use manual tap correction for HS400 on some variants
- renesas_sdhi: Add support for manual correction of tap values for tunings
-----BEGIN PGP SIGNATURE-----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=gILc
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for host software queue for (e)MMC/SD
- Throttle polling rate for CMD6
- Update CMD13 busy condition check for CMD6 commands
- Improve busy detect polling for erase/trim/discard/HPI
- Fixup support for HW busy detection for HPI commands
- Re-work and improve support for eMMC sanitize commands
MMC host:
- mmci:
* Add support for sdmmc variant revision 2.0
- mmci_sdmmc:
* Improve support for busyend detection
* Fixup support for signal voltage switch
* Add support for tuning with delay block
- mtk-sd:
* Fix another SDIO irq issue
- sdhci:
* Disable native card detect when GPIO based type exist
- sdhci:
* Add option to defer request completion
- sdhci_am654:
* Add support to set a tap value per speed mode
- sdhci-esdhc-imx:
* Add support for i.MX8MM based variant
* Fixup support for standard tuning on i.MX8 usdhc
* Optimize for strobe/clock dll settings
* Fixup support for system and runtime suspend/resume
- sdhci-iproc:
* Update regulator/bus-voltage management for bcm2711
- sdhci-msm:
* Prevent clock gating with PWRSAVE_DLL on broken variants
* Fix management of CQE during SDHCI reset
- sdhci-of-arasan:
* Add support for auto tuning on ZynqMP based platforms
- sdhci-omap:
* Add support for system suspend/resume
- sdhci-sprd:
* Add support for HW busy detection
* Enable support host software queue
- sdhci-tegra:
* Add support for HW busy detection
- tmio/renesas_sdhi:
* Enforce retune after runtime suspend
- renesas_sdhi:
* Use manual tap correction for HS400 on some variants
* Add support for manual correction of tap values for tunings"
* tag 'mmc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: cavium-octeon: remove nonsense variable coercion
mmc: mediatek: fix SDIO irq issue
mmc: mmci_sdmmc: Fix clear busyd0end irq flag
dt-bindings: mmc: Fix node name in an example
mmc: core: Re-work the code for eMMC sanitize
mmc: sdhci: use FIELD_GET for preset value bit masks
mmc: sdhci-of-at91: Display clock changes for debug purpose only
mmc: sdhci: iproc: Add custom set_power() callback for bcm2711
mmc: sdhci: am654: Use sdhci_set_power_and_voltage()
mmc: sdhci: at91: Use sdhci_set_power_and_voltage()
mmc: sdhci: milbeaut: Use sdhci_set_power_and_voltage()
mmc: sdhci: arasan: Use sdhci_set_power_and_voltage()
mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()
mmc: vub300: Use scnprintf() for avoiding potential buffer overflow
dt-bindings: mmc: synopsys-dw-mshc: fix clock-freq-min-max in example
sdhci: tegra: Enable MMC_CAP_WAIT_WHILE_BUSY host capability
sdhci: tegra: Implement Tegra specific set_timeout callback
mmc: sdhci-omap: Add Support for Suspend/Resume
mmc: renesas_sdhi: simplify execute_tuning
mmc: renesas_sdhi: Use BITS_PER_LONG helper
...
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel side changes:
- A couple of x86/cpu cleanups and changes were grandfathered in due
to patch dependencies. These clean up the set of CPU model/family
matching macros with a consistent namespace and C99 initializer
style.
- A bunch of updates to various low level PMU drivers:
* AMD Family 19h L3 uncore PMU
* Intel Tiger Lake uncore support
* misc fixes to LBR TOS sampling
- optprobe fixes
- perf/cgroup: optimize cgroup event sched-in processing
- misc cleanups and fixes
Tooling side changes are to:
- perf {annotate,expr,record,report,stat,test}
- perl scripting
- libapi, libperf and libtraceevent
- vendor events on Intel and S390, ARM cs-etm
- Intel PT updates
- Documentation changes and updates to core facilities
- misc cleanups, fixes and other enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits)
cpufreq/intel_pstate: Fix wrong macro conversion
x86/cpu: Cleanup the now unused CPU match macros
hwrng: via_rng: Convert to new X86 CPU match macros
crypto: Convert to new CPU match macros
ASoC: Intel: Convert to new X86 CPU match macros
powercap/intel_rapl: Convert to new X86 CPU match macros
PCI: intel-mid: Convert to new X86 CPU match macros
mmc: sdhci-acpi: Convert to new X86 CPU match macros
intel_idle: Convert to new X86 CPU match macros
extcon: axp288: Convert to new X86 CPU match macros
thermal: Convert to new X86 CPU match macros
hwmon: Convert to new X86 CPU match macros
platform/x86: Convert to new CPU match macros
EDAC: Convert to new X86 CPU match macros
cpufreq: Convert to new X86 CPU match macros
ACPI: Convert to new X86 CPU match macros
x86/platform: Convert to new CPU match macros
x86/kernel: Convert to new CPU match macros
x86/kvm: Convert to new CPU match macros
x86/perf/events: Convert to new CPU match macros
...
The new macro set has a consistent namespace and uses C99 initializers
instead of the grufty C89 ones.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lkml.kernel.org/r/20200320131510.285691129@linutronix.de
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200226223125.GA20630@embeddedor
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On the Acer Aspire Switch 10 (SW5-012) microSD slot always reports the card
being write-protected even though microSD cards do not have a write-protect
switch at all.
Add a new DMI_QUIRK_SD_NO_WRITE_PROTECT quirk which when set sets
the MMC_CAP2_NO_WRITE_PROTECT flag on the controller for the external SD
slot; and add a DMI quirk table entry which selects this quirk for the
Acer SW5-012.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200316184753.393458-2-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on a sample of 7 DSDTs from Cherry Trail devices using an AXP288
PMIC depending on the design one of 2 possible LDOs on the PMIC is used
for the MMC signalling voltage, either DLDO3 or GPIO1LDO (GPIO1 pin in
low noise LDO mode).
The Lenovo Miix 320-10ICR uses GPIO1LDO in the SHC1 ACPI device's DSM
methods to set 3.3 or 1.8 signalling voltage and this appears to work
as advertised, so presumably the device is actually using GPIO1LDO for
the external microSD signalling voltage.
But this device has a bug in the _PS0 method of the SHC1 ACPI device,
the DSM remembers the last set signalling voltage and the _PS0 restores
this after a (runtime) suspend-resume cycle, but it "restores" the voltage
on DLDO3 instead of setting it on GPIO1LDO as the DSM method does. DLDO3
is used for the LCD and setting it to 1.8V causes the LCD to go black.
This commit works around this issue by calling the Intel DSM to reset the
signal voltage to 3.3V after the host has been runtime suspended.
This will make the _PS0 method reprogram the DLDO3 voltage to 3.3V, which
leaves it at its original setting fixing the LCD going black.
This commit adds and uses a DMI quirk mechanism to only trigger this
workaround on the Lenovo Miix 320 while leaving the behavior of the
driver unchanged on other devices.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=111294
BugLink: https://gitlab.freedesktop.org/drm/intel/issues/355
Reported-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200316184753.393458-1-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Since we have a generic helper, drop custom implementation in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The SD host controller specification defines 3 types software reset:
software reset for data line, software reset for command line and software
reset for all. Software reset for all means this reset affects the entire
Host controller except for the card detection circuit.
In sdhci_runtime_resume_host() we always do a software "reset for all",
which causes the Spreadtrum variant controller to work abnormally after
resuming. To fix the problem, let's do a software reset for the data and
the command part, rather than "for all".
However, as sdhci_runtime_resume() is a common sdhci function and we don't
want to change the behaviour for other variants, let's introduce a new
in-parameter for it. This enables the caller to decide if a "reset for all"
shall be done or not.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 111 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.567572064@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel BYT-based controllers do not have a LED signal line. Nevertheless
sdhci_led_control() takes more than twice as long as sdhci_send_command(),
even though it does nothing. Use the new SDHCI_QUIRK_NO_LED quirk to
disable LED control for Intel BYT-based controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull perf updates from Ingo Molnar:
"The main updates in this cycle were:
- Lots of perf tooling changes too voluminous to list (big perf trace
and perf stat improvements, lots of libtraceevent reorganization,
etc.), so I'll list the authors and refer to the changelog for
details:
Benjamin Peterson, Jérémie Galarneau, Kim Phillips, Peter
Zijlstra, Ravi Bangoria, Sangwon Hong, Sean V Kelley, Steven
Rostedt, Thomas Gleixner, Ding Xiang, Eduardo Habkost, Thomas
Richter, Andi Kleen, Sanskriti Sharma, Adrian Hunter, Tzvetomir
Stoyanov, Arnaldo Carvalho de Melo, Jiri Olsa.
... with the bulk of the changes written by Jiri Olsa, Tzvetomir
Stoyanov and Arnaldo Carvalho de Melo.
- Continued intel_rdt work with a focus on playing well with perf
events. This also imported some non-perf RDT work due to
dependencies. (Reinette Chatre)
- Implement counter freezing for Arch Perfmon v4 (Skylake and newer).
This allows to speed up the PMI handler by avoiding unnecessary MSR
writes and make it more accurate. (Andi Kleen)
- kprobes cleanups and simplification (Masami Hiramatsu)
- Intel Goldmont PMU updates (Kan Liang)
- ... plus misc other fixes and updates"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (155 commits)
kprobes/x86: Use preempt_enable() in optimized_callback()
x86/intel_rdt: Prevent pseudo-locking from using stale pointers
kprobes, x86/ptrace.h: Make regs_get_kernel_stack_nth() not fault on bad stack
perf/x86/intel: Export mem events only if there's PEBS support
x86/cpu: Drop pointless static qualifier in punit_dev_state_show()
x86/intel_rdt: Fix initial allocation to consider CDP
x86/intel_rdt: CBM overlap should also check for overlap with CDP peer
x86/intel_rdt: Introduce utility to obtain CDP peer
tools lib traceevent, perf tools: Move struct tep_handler definition in a local header file
tools lib traceevent: Separate out tep_strerror() for strerror_r() issues
perf python: More portable way to make CFLAGS work with clang
perf python: Make clang_has_option() work on Python 3
perf tools: Free temporary 'sys' string in read_event_files()
perf tools: Avoid double free in read_event_file()
perf tools: Free 'printk' string in parse_ftrace_printk()
perf tools: Cleanup trace-event-info 'tdata' leak
perf strbuf: Match va_{add,copy} with va_end
perf test: S390 does not support watchpoints in test 22
perf auxtrace: Include missing asm/bitsperlong.h to get BITS_PER_LONG
tools include: Adopt linux/bits.h
...
After host requests RESET_FOR_ALL action, the hardware output an
interrupt for OS and waiting for the OS to approve.
Before writing this fix, ACPI GED has handled the interrupt. But
the ACPI GED belongs to a slow process, and sometimes the handling
process time is more than 100ms(Mutex wait more than 100ms). So
drop the GED solution and add this quirk fix.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device specific resource can be free in free_slot after
removing host controller.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Zero is a valid IRQ number and is being used on some CHT tablets. Stop
treating it as an error.
Reported-by: Luke Ross <luke@lukeross.name>
Fixes: 1b7ba57ecc ("mmc: sdhci-acpi: Handle return value of platform_get_irq")
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel DSM function 8 has been used to identify transfer modes that are not
working on some CHT boards. Add support for that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a ->setup_host() callback so that device-specific changes can be made
to the mmc host controller before it is added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch supports HS400 for AMD upcoming emmc 5.0 controller.The
HS400 and HS200 mode requires hardware work around also. This patch
adds the quirks for the same.
Signed-off-by: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Intel host controllers use an ACPI device-specific method to ensure
correct voltage switching. Fix voltage switch for those, by adding a call
to the DSM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let devices define their own private data to facilitate device-specific
operations. The size of the private structure is specified in the
sdhci_acpi_slot structure, then sdhci_acpi_probe() will allocate extra
space for it, and sdhci_acpi_priv() can be used to get a reference to it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tidy Intel slot probe functions into one. A single function can be used
because the logic uses hid / uid as necessary to identify devices anyway.
This gets rid of some pointless comments and checks for variables that
cannot possibly be NULL, as well as giving the function a name that
identifies it as specific to Intel controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of acpi_device_uid() instead of open coding.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ACPI_COMPANION() macro reduces a code to get a companion device out of
struct device.
Use it instead of an old method.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was never used and introduce a warning
drivers/mmc/host/sdhci-acpi.c: In function 'sdhci_acpi_sdio_probe_slot':
drivers/mmc/host/sdhci-acpi.c:297:21: warning: variable 'host' set but
not used [-Wunused-but-set-variable]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GPDwin uses PCI wifi which conflicts with SDIO's use of
acpi_device_fix_up_power() on child device nodes. Specifically
acpi_device_fix_up_power() causes the wifi module to get turned off.
Identifying GPDwin is problematic, but since SDIO is only used for wifi,
the presence of the PCI wifi card in the expected slot with an ACPI
companion node, is used to indicate that acpi_device_fix_up_power() should
be avoided.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC_CAP2_HC_ERASE_SZ is used only by a few mmc host drivers. Its intent
is to enable eMMC's high-capacity erase size, as to improve the behaviour
of the erase operations.
We should strive to avoid software configuration options that aren't
necessary, but instead deploy common behaviours. For these reasons, let's
remove the capability bit for MMC_CAP2_HC_ERASE_SZ and make it the default
behaviour.
Note that this change doesn't affect eMMCs supporting trim/discard, because
these commands operates on sectors and takes precedence over erase
commands.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
The acpi-subsys already calls acpi_bus_get_status() and checks that
device->status.present is set before even registering the platform_device
so out probe function will never get called if device->status.present is
false and there is no need for this check.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Devices might save and restore tuning values so that re-tuning might not be
needed after a pm transition. Let drivers decide by pushing the
mmc_retune_needed() logic down to them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
With commit 67bf5156ed ("gpio / ACPI: fix returned error from
acpi_dev_gpio_irq_get()"), mmc_gpiod_request_cd() returns -EPROBE_DEFER if
GPIO is not ready when sdhci-acpi driver is probed, and sdhci-acpi driver
should be probed again later in this case.
This fixes an order issue when both GPIO and sdhci-acpi drivers are built
as modules.
CC: stable@vger.kernel.org # v4.9
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177101
Tested-by: Jonas Aaberg <cja@gmx.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e5bbf30733 ("mmc: sdhci-acpi: Ensure connected devices are
powered when probing") introduced code to powerup any acpi child
nodes listed in the dstd. But some dstd-s list all possible devices
used on some board variants, while reporting if the device is actually
present and enabled in the status field of the device.
So we end up calling the acpi _PS0 (power-on) method for devices which
are not actually present. This does not always end well, e.g. on my
cube iwork8 air tablet, this results in freezing the entire tablet as
soon as the r8723bs module is loaded.
This commit fixes this by checking the child device's status.present
and status.enabled bits and only call acpi_device_fix_up_power()
if both are set.
Fixes: e5bbf30733 ("mmc: sdhci-acpi: Ensure connected devices are powered when probing")
BugLink: https://github.com/hadess/rtl8723bs/issues/80
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add an entry for the SDIO bus in the ECS EF20 cherry trail laptop:
Device (SDHB) {
Name (_ADR, 0x00110000)
Name (_HID, "80860F14" /* Intel Baytrail SDIO/MMC Host Controller */)
Name (_CID, "PNP0D40" /* SDA Standard Compliant SD Host Controller */)
Name (_DDN, "Intel(R) SDIO Controller - 80862295")
Name (_UID, 0x02)
Name (_HRV, One)
A SDHB device with the same _HID and _UID can also be found on other
cherry trail products like Chuwi Hi10.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set MMC_CAP_CMD_DURING_TFR for Intel BYT and related eMMC host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wzSC
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds"
* tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc: (135 commits)
mmc: rtsx_pci: Remove deprecated create_singlethread_workqueue
mmc: rtsx_pci: Enable MMC_CAP_ERASE to allow erase/discard/trim requests
mmc: rtsx_pci: Use the provided busy timeout from the mmc core
mmc: sdhci-pltfm: Drop define for SDHCI_PLTFM_PMOPS
mmc: sdhci-pltfm: Convert to use the SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pltfm: Make sdhci_pltfm_suspend|resume() static
mmc: sdhci-esdhc-imx: Use common sdhci_suspend|resume_host()
mmc: sdhci-esdhc-imx: Assign system PM ops within #ifdef CONFIG_PM_SLEEP
mmc: sdhci-sirf: Remove non needed #ifdef CONFIG_PM* for dev_pm_ops
mmc: sdhci-s3c: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-pxav3: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-of-esdhc: Simplify code by using SIMPLE_DEV_PM_OPS
mmc: sdhci-acpi: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pci-core: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: Change the max discard sectors and erase response when HW busy detect
phy: rockchip-emmc: Wait even longer for the DLL to lock
phy: rockchip-emmc: Be tolerant to card clock of 0 in power on
mmc: sdhci-of-arasan: Revert: Always power the PHY off/on when clock changes
mmc: sdhci-msm: Add support for UHS cards
mmc: sdhci-msm: Add set_uhs_signaling() implementation
...
By using the SET_SYSTEM_SLEEP_PM_OPS when assigning the system PM
callbacks, we can remove some #ifdefs so code becomes a bit cleaner.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The CMD19/CMD14 bus width test has been found to be unreliable in
some cases. It is not essential, so simply remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some devices connected to the SDHCI controller may have separate enabling
lines that are controlled through GPIO. These devices need to be powered
on and enabled before probing. This is to ensure all devices connected can
be seen by the controller.
Note, for "stable" this patch depends on the following change:
commit 78a898d0e3 ("ACPI / PM: Export acpi_device_fix_up_power()")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reported-and-tested-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Cc: <stable@vger.kernel.org> # 4.5+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Laszlo Fiat <laszlo.fiat@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112571
Link: http://lkml.kernel.org/r/CA+7w51inLtQSr656bJvOjGG9oQWKYPXH+xxDPJKbeJ=CcrkS9Q@mail.gmail.com
Set MMC_CAP_AGGRESSIVE_PM for Broxton host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9250aea76b ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baytrail eMMC/SD/SDIO host controllers have been known to
hang. A change to a hardware setting has been found to
reduce the occurrence of such hangs. This patch ensures
the correct setting.
This patch applies cleanly to v4.4+. It could go to
earlier kernels also, so I will send backports to the
stable list in due course.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This hook was solely used to set the DMA mask, which is now done
by the newly-added sdhci_set_dma_mask() function.
The use of a flag to ensure the mask is only set once is a strong hint
that it should not have been done there anyway.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds the HIDs for Qualcomm Technologies Inc SDHC
controllers:
QCOM8051: non-removable device that does not support 1.8v
QCOM8052: non-removable device that does support 1.8v
Signed-off-by: Philip Elcan <pelcan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch enables sdhci-acpi devices to suspend/resume asynchronously.
This will improve system suspend/resume speed. After enabling the
sdhci-acpi devices and all their child devices to suspend/resume
asynchronously on ASUS T100TA, the system suspend-to-idle time is
reduced from 1645ms to 1089ms, and the system resume time is reduced
from 940ms to 908ms.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
