McASP pins can be used as GPIO, add optional section to enable GPIO support
for McASP.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dismod property can be used to specify the drive on level of inactive
TX slots.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An underrun (playback) event occurs when the serializer transfer
data from the XRBUF buffer to the XRSR shift register, but the
XRBUF hasn't been filled. Similarly, the overrun (capture) event
occurs when data from the XRSR shift register is transferred to
the XRBUF but it hasn't been read yet.
These events are handled as XRUN events that cause the pcm to stop.
The stream has to be explicitly restarted by the userspace which
ensures that after stopping/starting McASP the data transfer is
aligned with DMA. The other possibility was to internally stop and
start McASP without DMA even knowing about it.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
s/interrupts-names/interrupt-names/g
s/clocks-names/clock-names/g
Some of the binding files and device tree files get this wrong and the
kernel won't be able to pick it up. Fix them up now so that they don't
get widely used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by : Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Optional DT property to specify the desired parent clock for the McASP fck
clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The IP in DRA7xx is similar to the IP found in TI81xxAM3xxx/AM4xxx type of
SoCs but it is is integrated with sDMA instead of eDMA. The suitable pcm
driver for DRA7xx is the omap-pcm driver which is using dmaengine.
In the driver we can configure both dma related structures used for eDMA and
sDMA. The only thing we need to make sure that we set the correct dma_data
at startup with snd_soc_dai_set_dma_data()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
AM43xx have the same McASP IP as AM33xx and both platform uses eDMA. Modify
the Kconfig so it will be possible to add audio support for AM43xx based
boards later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove last reference to num-serializer in davinci-mcasp devicetree
binding document.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The serial-dir array gives this information so there is no need to have the
num-serializer property in DT description.
Just ignore the property in the driver the DTS files can be updated
separately without regression.
Update the documentation at the same time for davinci-mcasp
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Makes interrupts property optional as the interrupts are not currently
used by the driver and adds interrupt-names property to name listed
interrupts. Currently know interrupt names are "tx" and "rx".
- Improve tdm-slots propery description
- Improve op-mode property description
- Add pinctrl-names and pinctrl-0 properties
- Remove #address-cells and #size-cells as they are not needed.
- Bracket named interrupts property tuples for uniformity.
- Add missing "for" to serial-dir prop in DT bindings doc.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Change the model omap2-mcasp-audio in compatible property to
am33xx-mcasp-audio as omap2 does not have mcasp.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Extract DMA channels directly from DT as they can not be found from
platform resources anymore. This is a work-around until davinci audio
driver is updated to use dmaengine.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a separate register location for data port registers to
mcasp DT bindings. On am33xx SoCs the McASP registers are mapped
trough L4 interconnect, but data port registers are also mapped trough
L3 bus to a different memory location.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The OMAP2+ variant of McASP is different from Davinci variant w.r.to
some register offset.
Changes
- Add new MCASP_VERSION_3 to identify new variant. New DT compatible
"ti,omap2-mcasp-audio" to identify version 3 controller.
- The register offsets are handled depending on the version.
Note:
DMA parameters (dma fifo offset) are not updated and will be done later.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree probe for McASP driver.
Note:
DMA parameters are not populated from DT and will be done later.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
