It advertises "host bridge" instead of "PCI to PCI bridge" which confuses
the Linux probe code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When PCI_REASSIGN_ALL_RSRC is set, we used to clear all bus resources
at the beginning of survey and re-allocate them later.
This changes it so instead, during early fixup, we mark all resources
as IORESOURCE_UNSET and move them down to be 0-based.
Later, if bus resources are still unset at the beginning of the survey,
then we clear them.
This shouldn't impact the re-assignment case on 4xx, but will enable
us to have the platform do some custom resource assignment before the
survey, by clearing individual resources IORESOURCE_UNSET bit.
Also limits the clutter in the kernel log from fixup when re-assigning
since we don't care about the offset applied to the BAR values in this
case.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some platforms need to perform resource allocation using a custom algorithm
due to HW constraints, or may want to tweak things globally below a host
bridge. For example OPAL support for IODA will need to perform a
resource allocation pass that applies IODA specific segmentation
constraints to MMIO which cannot be done simply using the kernel generic
resource management code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a pgprot combination required by some cache-enabled IO device
mappings, such as Freescale datapath (QMan and BMan) portals.
Signed-off-by: Geoff Thorpe <geoff@geoffthorpe.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All interrupts which must be non threaded are marked
IRQF_NO_THREAD. So it's safe to allow force threaded handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
IPI handlers cannot be threaded. Remove the obsolete IRQF_DISABLED
flag (see commit e58aa3d2) while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cascade handlers must run in hard interrupt context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cascade interrupt must run in hard interrupt context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The RTAS firmware flash update is conducted using an RTAS call that is
serialized by lock_rtas() which uses spin_lock. While the flash is in
progress, rtasd performs scan for any RTAS events that are generated by
the system. rtasd keeps scanning for the RTAS events generated on the
machine. This is performed via workqueue mechanism. The rtas_event_scan()
also uses an RTAS call to scan the events, eventually trying to acquire
the spin_lock before issuing the request.
The flash update takes a while to complete and during this time, any other
RTAS call has to wait. In this case, rtas_event_scan() waits for a long time
on the spin_lock resulting in a soft lockup.
Fix: Just before the flash update is performed, the queued rtas_event_scan()
work item is cancelled from the work queue so that there is no other RTAS
call issued while the flash is in progress. After the flash completes, the
system reboots and the rtas_event_scan() is rescheduled.
Signed-off-by: Suzuki Poulose <suzuki@in.ibm.com>
Signed-off-by: Ravi Nittala <ravi.nittala@in.ibm.com>
Reported-by: Divya Vikas <divya.vikas@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch add the Chroma platform to WSP/PowerEN, which is a PCIe
card (a defconfig is included).
The card includes an H8 service processor that is used to manage the
card. The H8 is connected over the second serial UART on the PowerEN
chip so this patch includes a simple 16550 driver to enable
communication, mostly for "power off" and "rebooting".
This patch also includes a, WSP specific, "halt" method that will shut
of all A2 cores but still leave power on at the chip level. This is
desirable, especially if you wish to interrogate the chip with a
hardware probe after the halt.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The 'u' command will print the TLB on book3e parts and the SLB on
Book3s parts, but the help system doesn't say that correctly.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a fault handler that responds to illegal Coprocessor
types. Currently all CTs are treated and illegal. There are two ways
to report the fault back to the application. If the application used
the record form ("icswx.") then the architected "reject" is emulated.
If the application did not used the record form ("icswx") then it is
selectable by config whether the failure is silent (as architected) or
a SIGILL is generated.
In all cases pr_warn() is used to log the bad CT.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
ICSWX is also used by the A2 processor to access coprocessors,
although not all "chips" that contain A2s have coprocessors.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some processors, like embedded, that already have a PID register that
is managed by the system. This patch separates the ACOP and PID
processing into separate files so that the ACOP code can be shared.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
np is initialized to the result of calling a function that calls
of_node_get, so of_node_put should be called before the pointer is dropped.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1,e2;
@@
* e = \(of_find_node_by_type\|of_find_node_by_name\)(...)
... when != of_node_put(e)
when != true e == NULL
when != e2 = e
e = e1
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
np is initialized to the result of calling a function that calls
of_node_get, so of_node_put should be called before the pointer is dropped.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1,e2;
@@
* e = \(of_find_node_by_type\|of_find_node_by_name\)(...)
... when != of_node_put(e)
when != true e == NULL
when != e2 = e
e = e1
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some pseries IOMMUs cache TCEs but don't snoop when the TCEs are changed
in memory, hence we need manually invalidate in software.
This adds code to do the invalidate. It keys off a device tree property
to say where the to do the MMIO for the invalidate and some information
on what the format of the invalidate including some magic routing info.
it_busno get overloaded with this magic routing info and it_index with
the MMIO address for the invalidate command.
This then gets hooked into the building and freeing of TCEs.
This is only useful on bare metal pseries. pHyp takes care of this when
virtualised.
Based on patch from Milton with cleanups from Mikey.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
decrementer_check_overflow is called from arch_local_irq_restore so
we want to make it as light weight as possible. As such, turn
decrementer_check_overflow into an inline function.
To avoid a circular mess of includes, separate out the two components
of struct decrementer_clock and keep the struct clock_event_device
part local to time.c.
The fast path improves from:
arch_local_irq_restore
0: mflr r0
4: std r0,16(r1)
8: stdu r1,-112(r1)
c: stb r3,578(r13)
10: cmpdi cr7,r3,0
14: beq- cr7,24 <.arch_local_irq_restore+0x24>
...
24: addi r1,r1,112
28: ld r0,16(r1)
2c: mtlr r0
30: blr
to:
arch_local_irq_restore
0: std r30,-16(r1)
4: ld r30,0(r2)
8: stb r3,578(r13)
c: cmpdi cr7,r3,0
10: beq- cr7,6c <.arch_local_irq_restore+0x6c>
...
6c: ld r30,-16(r1)
70: blr
Unfortunately we still setup a local TOC (due to -mminimal-toc). Yet
another sign we should be moving to -mcmodel=medium.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix some formatting issues and use the DECREMENTER_MAX
define instead of 0x7fffffff.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The clockevents code uses max_delta_ns to avoid calling a
clockevent with too large a value.
Remove the redundant version of this in the timer_interrupt
code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use clocksource_register_hz which calculates the shift/mult
factors for us. Also remove the shift = 22 assumption in
vsyscall_update - thanks to Paul Mackerras and John Stultz for
catching that.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can use clockevents_calc_mult_shift instead of doing all
the work ourselves.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When re-enabling interrupts we have code to handle edge sensitive
decrementers by resetting the decrementer to 1 whenever it is negative.
If interrupts were disabled long enough that the decrementer wrapped to
positive we do nothing. This means interrupts can be delayed for a long
time until it finally goes negative again.
While we hope interrupts are never be disabled long enough for the
decrementer to go positive, we have a very good test team that can
drive any kernel into the ground. The softlockup data we get back
from these fails could be seconds in the future, completely missing
the cause of the lockup.
We already keep track of the timebase of the next event so use that
to work out if we should trigger a decrementer exception.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
altroot support has been gone for years, along with arch/*/asm/namei.h;
looks like a dummy survivor that sat it out in microblaze tree...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (86 commits)
ipv4: fix redirect handling
ping: dont increment ICMP_MIB_INERRORS
sky2: fix hang in napi_disable
sky2: enforce minimum ring size
bonding: Don't allow mode change via sysfs with slaves present
f_phonet: fix page offset of first received fragment
stmmac: fix pm functions avoiding sleep on spinlock
stmmac: remove spin_lock in stmmac_ioctl.
stmmac: parameters auto-tuning through HW cap reg
stmmac: fix advertising 1000Base capabilties for non GMII iface
stmmac: use mdelay on timeout of sw reset
sky2: version 1.30
sky2: used fixed RSS key
sky2: reduce default Tx ring size
sky2: rename up/down functions
sky2: pci posting issues
sky2: fix hang on shutdown (and other irq issues)
r6040: fix check against MCRO_HASHEN bit in r6040_multicast_list
MAINTAINERS: change email address for shemminger
pch_gbe: Move #include of module.h
...
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Suspend: Fix bug in suspend statistics update
PM / Hibernate: Fix the early termination of test modes
PM / shmobile: Fix build of sh7372_pm_init() for CONFIG_PM unset
PM Sleep: Do not extend wakeup paths to devices with ignore_children set
PM / driver core: disable device's runtime PM during shutdown
PM / devfreq: correct Kconfig dependency
PM / devfreq: fix use after free in devfreq_remove_device
PM / shmobile: Avoid restoring the INTCS state during initialization
PM / devfreq: Remove compiler error after irq.h update
PM / QoS: Properly use the WARN() macro in dev_pm_qos_add_request()
PM / Clocks: Only disable enabled clocks in pm_clk_suspend()
ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix
PM / shmobile: Don't skip debugging output in pd_power_up()
Prevent tracing of preempt_disable() in get_cpu_var() in
kvm_clock_read(). When CONFIG_DEBUG_PREEMPT is enabled,
preempt_disable/enable() are traced and this causes the function_graph
tracer to go into an infinite recursion. By open coding the
preempt_disable() around the get_cpu_var(), we can use the notrace
version which prevents preempt_disable/enable() from being traced and
prevents the recursion.
Based on a similar patch for Xen from Jeremy Fitzhardinge.
Tested-by: Gleb Natapov <gleb@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
random: Fix handing of arch_get_random_long in get_random_bytes()
x86: Call stop_machine_text_poke() on all CPUs
x86, ioapic: Only print ioapic debug information for IRQs belonging to an ioapic chip
x86/mrst: Avoid reporting wrong nmi status
x86/mrst: Add support for Penwell clock calibration
x86/apic: Allow use of lapic timer early calibration result
x86/apic: Do not clear nr_irqs_gsi if no legacy irqs
x86/platform: Add a wallclock_init func to x86_platforms ops
x86/mce: Make mce_chrdev_ops 'static const'
* 'stable/for-linus-fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen-gntalloc: signedness bug in add_grefs()
xen-gntalloc: integer overflow in gntalloc_ioctl_alloc()
xen-gntdev: integer overflow in gntdev_alloc_map()
xen:pvhvm: enable PVHVM VCPU placement when using more than 32 CPUs.
xen/balloon: Avoid OOM when requesting highmem
xen: Remove hanging references to CONFIG_XEN_PLATFORM_PCI
xen: map foreign pages for shared rings by updating the PTEs directly
* 'unicore32' of git://github.com/gxt/linux:
unicore32, exec: remove redundant set_fs(USER_DS)
unicore32: Fix typo 'PUV3_I2C'
unicore32: drop unused Kconfig symbols
rtc: rtc-puv3: Add __devinit and __devexit markers for probe and remove
arch/unicore32: do not use EXTRA_AFLAGS or EXTRA_CFLAGS
unicore32: fix build error for find bitops
Some of the sun4v code patching occurs in inline functions visible
to, and usable by, modules.
Therefore we have to patch them up during module load.
Signed-off-by: David S. Miller <davem@davemloft.net>
To handle the large physical addresses, just make a simple wrapper
around remap_pfn_range() like MIPS does.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build regression introduced by commit 056879d2f2
(ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix) by moving
the intialization of the A3SP domain to a separate function and
providing an empty definition of it for CONFIG_PM unset.
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
These two syscalls were introduced during the last merge window.
Add the entries into the ARM call tables for them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit a15bd354f0.
It exceeded the padding on the SREGS struct, rendering the ABI
backwards-incompatible.
Conflicts:
arch/powerpc/kvm/powerpc.c
include/linux/kvm.h
Signed-off-by: Avi Kivity <avi@redhat.com>
Support guest/host-only profiling by switch perf msrs on
a guest entry if needed.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some cpus have special support for switching PERF_GLOBAL_CTRL msr.
Add logic to detect if such support exists and works properly and extend
msr switching code to use it if available. Also extend number of generic
msr switching entries to 8.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM on s390 always had a sync mmu. Any mapping change in userspace
mapping was always reflected immediately in the guest mapping.
- In older code the guest mapping was just an offset
- In newer code the last level page table is shared
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
There is a potential host deadlock in the tprot intercept handling.
We must not hold the mmap semaphore while resolving the guest
address. If userspace is remapping, then the memory detection in
the guest is broken anyway so we can safely separate the
address translation from walking the vmas.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
SIGP sense running may cause an intercept on higher level
virtualization, so handle it by checking the CPUSTAT_RUNNING flag.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
CPUSTAT_RUNNING was implemented signifying that a vcpu is not stopped.
This is not, however, what the architecture says: RUNNING should be
set when the host is acting on the behalf of the guest operating
system.
CPUSTAT_RUNNING has been changed to be set in kvm_arch_vcpu_load()
and to be unset in kvm_arch_vcpu_put().
For signifying stopped state of a vcpu, a host-controlled bit has
been used and is set/unset basically on the reverse as the old
CPUSTAT_RUNNING bit (including pushing it down into stop handling
proper in handle_stop()).
Cc: stable@kernel.org
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
On PPC64, put_sigset_t converts a sigset_t to a compat_sigset_t
before copying it to userspace. There is a typo in the case that
we have 4 words to copy, meaning that we corrupt the compat_sigset_t.
It appears that _NSIG_WORDS can't be greater than 2 at the moment
so this code is probably always optimised away anyway.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
