There is a problem when a driver requests a shared interrupt line to run a
threaded handler on it without IRQF_ONESHOT set if that flag has been set
already for the IRQ in question by somebody else. Namely, the request
fails which usually leads to a probe failure even though the driver might
have worked just fine with IRQF_ONESHOT, but it does not want to use it by
default. Currently, the only way to handle this is to try to request the
IRQ without IRQF_ONESHOT, but with IRQF_PROBE_SHARED set and if this fails,
try again with IRQF_ONESHOT set. However, this is a bit cumbersome and not
very clean.
When commit 7a36b901a6 ("ACPI: OSL: Use a threaded interrupt handler for
SCI") switched the ACPI subsystem over to using a threaded interrupt
handler for the SCI, it had to use IRQF_ONESHOT for it because that's
required due to the way the SCI handler works (it needs to walk all of the
enabled GPEs before the interrupt line can be unmasked). The SCI interrupt
line is not shared with other users very often due to the SCI handling
overhead, but on sone systems it is shared and when the other user of it
attempts to install a threaded handler, a flags mismatch related to
IRQF_ONESHOT may occur.
As it turned out, that happened to the pinctrl-amd driver and so commit
4451e8e841 ("pinctrl: amd: Add IRQF_ONESHOT to the interrupt request")
attempted to address the issue by adding IRQF_ONESHOT to the interrupt
flags in that driver, but this is now causing an IRQF_ONESHOT-related
mismatch to occur on another system which cannot boot as a result of it.
Clearly, pinctrl-amd can work with IRQF_ONESHOT if need be, but it should
not set that flag by default, so it needs a way to indicate that to the
interrupt subsystem.
To that end, introdcuce a new interrupt flag, IRQF_COND_ONESHOT, which will
only have effect when the IRQ line is shared and IRQF_ONESHOT has been set
for it already, in which case it will be promoted to the latter.
This is sufficient for drivers sharing the interrupt line with the SCI as
it is requested by the ACPI subsystem before any drivers are probed, so
they will always see IRQF_ONESHOT set for the interrupt in question.
Fixes: 4451e8e841 ("pinctrl: amd: Add IRQF_ONESHOT to the interrupt request")
Reported-by: Francisco Ayala Le Brun <francisco@videowindow.eu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: 6.8+ <stable@vger.kernel.org> # 6.8+
Closes: https://lore.kernel.org/lkml/CAN-StX1HqWqi+YW=t+V52-38Mfp5fAz7YHx4aH-CQjgyNiKx3g@mail.gmail.com/
Link: https://lore.kernel.org/r/12417336.O9o76ZdvQC@kreacher
- Core and platform-MSI
The core changes have been adopted from previous work which converted
ARM[64] to the new per device MSI domain model, which was merged to
support multiple MSI domain per device. The ARM[64] changes are being
worked on too, but have not been ready yet. The core and platform-MSI
changes have been split out to not hold up RISC-V and to avoid that
RISC-V builds on the scheduled for removal interfaces.
The core support provides new interfaces to handle wire to MSI bridges
in a straight forward way and introduces new platform-MSI interfaces
which are built on top of the per device MSI domain model.
Once ARM[64] is converted over the old platform-MSI interfaces and the
related ugliness in the MSI core code will be removed.
- Drivers:
- Add a new driver for the Andes hart-level interrupt controller
- Rework the SiFive PLIC driver to prepare for MSI suport
- Expand the RISC-V INTC driver to support the new RISC-V AIA
controller which provides the basis for MSI on RISC-V
- A few fixup for the fallout of the core changes.
The actual MSI parts for RISC-V were finalized late and have been
post-poned for the next merge window.
-----BEGIN PGP SIGNATURE-----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=7aXj
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2024-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI updates from Thomas Gleixner:
"Updates for the MSI interrupt subsystem and initial RISC-V MSI
support.
The core changes have been adopted from previous work which converted
ARM[64] to the new per device MSI domain model, which was merged to
support multiple MSI domain per device. The ARM[64] changes are being
worked on too, but have not been ready yet. The core and platform-MSI
changes have been split out to not hold up RISC-V and to avoid that
RISC-V builds on the scheduled for removal interfaces.
The core support provides new interfaces to handle wire to MSI bridges
in a straight forward way and introduces new platform-MSI interfaces
which are built on top of the per device MSI domain model.
Once ARM[64] is converted over the old platform-MSI interfaces and the
related ugliness in the MSI core code will be removed.
The actual MSI parts for RISC-V were finalized late and have been
post-poned for the next merge window.
Drivers:
- Add a new driver for the Andes hart-level interrupt controller
- Rework the SiFive PLIC driver to prepare for MSI suport
- Expand the RISC-V INTC driver to support the new RISC-V AIA
controller which provides the basis for MSI on RISC-V
- A few fixup for the fallout of the core changes"
* tag 'irq-msi-2024-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
irqchip/riscv-intc: Fix low-level interrupt handler setup for AIA
x86/apic/msi: Use DOMAIN_BUS_GENERIC_MSI for HPET/IO-APIC domain search
genirq/matrix: Dynamic bitmap allocation
irqchip/riscv-intc: Add support for RISC-V AIA
irqchip/sifive-plic: Improve locking safety by using irqsave/irqrestore
irqchip/sifive-plic: Parse number of interrupts and contexts early in plic_probe()
irqchip/sifive-plic: Cleanup PLIC contexts upon irqdomain creation failure
irqchip/sifive-plic: Use riscv_get_intc_hwnode() to get parent fwnode
irqchip/sifive-plic: Use devm_xyz() for managed allocation
irqchip/sifive-plic: Use dev_xyz() in-place of pr_xyz()
irqchip/sifive-plic: Convert PLIC driver into a platform driver
irqchip/riscv-intc: Introduce Andes hart-level interrupt controller
irqchip/riscv-intc: Allow large non-standard interrupt number
genirq/irqdomain: Don't call ops->select for DOMAIN_BUS_ANY tokens
irqchip/imx-intmux: Handle pure domain searches correctly
genirq/msi: Provide MSI_FLAG_PARENT_PM_DEV
genirq/irqdomain: Reroute device MSI create_mapping
genirq/msi: Provide allocation/free functions for "wired" MSI interrupts
genirq/msi: Optionally use dev->fwnode for device domain
genirq/msi: Provide DOMAIN_BUS_WIRED_TO_MSI
...
A future user of the matrix allocator, does not know the size of the matrix
bitmaps at compile time.
To avoid wasting memory on unnecessary large bitmaps, size the bitmap at
matrix allocation time.
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240222094006.1030709-11-apatel@ventanamicro.com
Users of the IRQCHIP_PLATFORM_DRIVER_{BEGIN,END} helpers rely on a fwspec
containing only the fwnode (and crucially a number of parameters set to 0)
together with a DOMAIN_BUS_ANY token to check whether a parent irqchip has
probed and registered a domain.
Since de1ff306dc ("genirq/irqdomain: Remove the param count restriction
from select()"), ops->select() is called unconditionally, meaning that
irqchips implementing select() now need to handle ANY as a match.
Instead of adding more esoteric checks to the individual drivers, add that
condition to irq_find_matching_fwspec(), and let it handle the corner case,
as per the comment in the function.
This restores the functionality of the above helpers.
Fixes: de1ff306dc ("genirq/irqdomain: Remove the param count restriction from select()")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20240220114731.1898534-1-maz@kernel.org
Link: https://lore.kernel.org/r/20240219-gic-fix-child-domain-v1-1-09f8fd2d9a8f@linaro.org
The affinity setting of interrupt threads happens in the context of the
thread when the thread is woken up by an hard interrupt. As this can be an
arbitrary after changing the affinity, the thread can become runnable on an
isolated CPU and cause isolation disruption.
Avoid this by checking the set affinity request in wait_for_interrupt() and
waking the threads immediately when the affinity is modified.
Note that this is of the most benefit on systems where the interrupt
affinity itself does not need to be deferred to the interrupt handler, but
even where that's not the case, the total dirsuption will be less.
Signed-off-by: Crystal Wood <crwood@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240122235353.15235-1-crwood@redhat.com
Some platform-MSI implementations require that power management is
redirected to the underlying interrupt chip device. To make this work
with per device MSI domains provide a new feature flag and let the
core code handle the setup of dev->pm_dev when set during device MSI
domain creation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240127161753.114685-14-apatel@ventanamicro.com
Reroute interrupt allocation in irq_create_fwspec_mapping() if the domain
is a MSI device domain. This is required to convert the support for wire
to MSI bridges to per device MSI domains.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240127161753.114685-13-apatel@ventanamicro.com
To support wire to MSI bridges proper in the MSI core infrastructure it is
required to have separate allocation/free interfaces which can be invoked
from the regular irqdomain allocaton/free functions.
The mechanism for allocation is:
- Allocate the next free MSI descriptor index in the domain
- Store the hardware interrupt number and the trigger type
which was extracted by the irqdomain core from the firmware spec
in the MSI descriptor device cookie so it can be retrieved by
the underlying interrupt domain and interrupt chip
- Use the regular MSI allocation mechanism for the newly allocated
index which returns a fully initialized Linux interrupt on succes
This works because:
- the domains have a fixed size
- each hardware interrupt is only allocated once
- the underlying domain does not care about the MSI index it only cares
about the hardware interrupt number and the trigger type
The free function looks up the MSI index in the MSI descriptor of the
provided Linux interrupt number and uses the regular index based free
functions of the MSI core.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240127161753.114685-12-apatel@ventanamicro.com
To support wire to MSI domains via the MSI infrastructure it is required to
use the firmware node of the device which implements this for creating the
MSI domain. Otherwise the existing firmware match mechanisms to find the
correct irqdomain for a wired interrupt which is connected to a wire to MSI
bridge would fail.
This cannot be used for the general case because not all devices provide
firmware nodes and all regular per device MSI domains are directly
associated to the device and have not be searched for.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240127161753.114685-11-apatel@ventanamicro.com
In preparation for providing a special allocation function for wired
interrupts which are connected to a wire to MSI bridge, split the inner
workings of msi_domain_alloc_irq_at() out into a helper function so the
code can be shared.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240127161753.114685-9-apatel@ventanamicro.com
irq_create_fwspec_mapping() requires translation of the firmware spec to a
hardware interrupt number and the trigger type information.
Wired interrupts which are connected to a wire to MSI bridge, like MBIGEN
are allocated that way. So far MBIGEN provides a regular irqdomain which
then hooks backwards into the MSI infrastructure. That's an unholy mess and
will be replaced with per device MSI domains which are regular MSI domains.
Interrupts on MSI domains are not supported by irq_create_fwspec_mapping(),
but for making the wire to MSI bridges sane it makes sense to provide a
special allocation/free interface in the MSI infrastructure. That avoids
the backdoors into the core MSI allocation code and just shares all the
regular MSI infrastructure.
Provide an optional translation callback in msi_domain_ops which can be
utilized by these wire to MSI bridges. No other MSI domain should provide a
translation callback. The default translation callback of the MSI
irqdomains will warn when it is invoked on a non-prepared MSI domain.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240127161753.114685-8-apatel@ventanamicro.com
Now that the GIC-v3 callback can handle invocation with a fwspec parameter
count of 0 lift the restriction in the core code and invoke select()
unconditionally when the domain provides it.
Preparatory change for per device MSI domains.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240127161753.114685-3-apatel@ventanamicro.com
Use the new __free() mechanism to remove all gotos and simplify the error
paths.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240122124243.44002-5-brgl@bgdev.pl
For better readability and maintenance keep headers in alphabetical
order.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240122124243.44002-4-brgl@bgdev.pl
alloc_desc() and early_irq_init() contain duplicated code to initialize
interrupt descriptors.
Replace that with a helper function.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240122085716.2999875-6-dawei.li@shingroup.cn
For a CONFIG_SPARSE_IRQ=n kernel, early_irq_init() is supposed to
initialize all interrupt descriptors.
It does except for irq_desc::resend_node, which ia only initialized for the
first descriptor.
Use the indexed decriptor and not the base pointer to address that.
Fixes: bc06a9e087 ("genirq: Use hlist for managing resend handlers")
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240122085716.2999875-5-dawei.li@shingroup.cn
there's little I can say which isn't in the individual changelogs.
The lengthier patch series are
- "kdump: use generic functions to simplify crashkernel reservation in
arch", from Baoquan He. This is mainly cleanups and consolidation of
the "crashkernel=" kernel parameter handling.
- After much discussion, David Laight's "minmax: Relax type checks in
min() and max()" is here. Hopefully reduces some typecasting and the
use of min_t() and max_t().
- A group of patches from Oleg Nesterov which clean up and slightly fix
our handling of reads from /proc/PID/task/... and which remove
task_struct.therad_group.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZUQP9wAKCRDdBJ7gKXxA
jmOAAQDh8sxagQYocoVsSm28ICqXFeaY9Co1jzBIDdNesAvYVwD/c2DHRqJHEiS4
63BNcG3+hM9nwGJHb5lyh5m79nBMRg0=
=On4u
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2023-11-02-14-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"As usual, lots of singleton and doubleton patches all over the tree
and there's little I can say which isn't in the individual changelogs.
The lengthier patch series are
- 'kdump: use generic functions to simplify crashkernel reservation
in arch', from Baoquan He. This is mainly cleanups and
consolidation of the 'crashkernel=' kernel parameter handling
- After much discussion, David Laight's 'minmax: Relax type checks in
min() and max()' is here. Hopefully reduces some typecasting and
the use of min_t() and max_t()
- A group of patches from Oleg Nesterov which clean up and slightly
fix our handling of reads from /proc/PID/task/... and which remove
task_struct.thread_group"
* tag 'mm-nonmm-stable-2023-11-02-14-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (64 commits)
scripts/gdb/vmalloc: disable on no-MMU
scripts/gdb: fix usage of MOD_TEXT not defined when CONFIG_MODULES=n
.mailmap: add address mapping for Tomeu Vizoso
mailmap: update email address for Claudiu Beznea
tools/testing/selftests/mm/run_vmtests.sh: lower the ptrace permissions
.mailmap: map Benjamin Poirier's address
scripts/gdb: add lx_current support for riscv
ocfs2: fix a spelling typo in comment
proc: test ProtectionKey in proc-empty-vm test
proc: fix proc-empty-vm test with vsyscall
fs/proc/base.c: remove unneeded semicolon
do_io_accounting: use sig->stats_lock
do_io_accounting: use __for_each_thread()
ocfs2: replace BUG_ON() at ocfs2_num_free_extents() with ocfs2_error()
ocfs2: fix a typo in a comment
scripts/show_delta: add __main__ judgement before main code
treewide: mark stuff as __ro_after_init
fs: ocfs2: check status values
proc: test /proc/${pid}/statm
compiler.h: move __is_constexpr() to compiler.h
...
- Make the quirk for non-maskable MSI interrupts in the affinity setter
functional again.
It was broken by a MSI core code update, which restructured the code in
a way that the quirk flag was not longer set correctly.
Trying to restore the core logic caused a deeper inspection and it
turned out that the extra quirk flag is not required at all because
it's the inverse of the reservation mode bit, which only can be set
when the MSI interrupt is maskable.
So the trivial fix is to use the reservation mode check in the affinity
setter function and remove almost 40 lines of code related to the
no-mask quirk flag.
- Cure a Kconfig dependency issue which causes compile fails by correcting
the conditionals in the affected heaer files.
- Clean up coding style in the UV APIC driver.
-----BEGIN PGP SIGNATURE-----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=2lhV
-----END PGP SIGNATURE-----
Merge tag 'x86-apic-2023-10-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 APIC updates from Thomas Gleixner:
- Make the quirk for non-maskable MSI interrupts in the affinity setter
functional again.
It was broken by a MSI core code update, which restructured the code
in a way that the quirk flag was not longer set correctly.
Trying to restore the core logic caused a deeper inspection and it
turned out that the extra quirk flag is not required at all because
it's the inverse of the reservation mode bit, which only can be set
when the MSI interrupt is maskable.
So the trivial fix is to use the reservation mode check in the
affinity setter function and remove almost 40 lines of code related
to the no-mask quirk flag.
- Cure a Kconfig dependency issue which causes compile failures by
correcting the conditionals in the affected header files.
- Clean up coding style in the UV APIC driver.
* tag 'x86-apic-2023-10-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic/msi: Fix misconfigured non-maskable MSI quirk
x86/msi: Fix compile error caused by CONFIG_GENERIC_MSI_IRQ=y && !CONFIG_X86_LOCAL_APIC
x86/platform/uv/apic: Clean up inconsistent indenting
irq_remove_generic_chip() calculates the Linux interrupt number for removing the
handler and interrupt chip based on gc::irq_base as a linear function of
the bit positions of set bits in the @msk argument.
When the generic chip is present in an irq domain, i.e. created with a call
to irq_alloc_domain_generic_chips(), gc::irq_base contains not the base
Linux interrupt number. It contains the base hardware interrupt for this
chip. It is set to 0 for the first chip in the domain, 0 + N for the next
chip, where $N is the number of hardware interrupts per chip.
That means the Linux interrupt number cannot be calculated based on
gc::irq_base for irqdomain based chips without a domain map lookup, which
is currently missing.
Rework the code to take the irqdomain case into account and calculate the
Linux interrupt number by a irqdomain lookup of the domain specific
hardware interrupt number.
[ tglx: Massage changelog. Reshuffle the logic and add a proper comment. ]
Fixes: cfefd21e69 ("genirq: Add chip suspend and resume callbacks")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231024150335.322282-1-herve.codina@bootlin.com
commit ef8dd01538 ("genirq/msi: Make interrupt allocation less
convoluted"), reworked the code so that the x86 specific quirk for affinity
setting of non-maskable PCI/MSI interrupts is not longer activated if
necessary.
This could be solved by restoring the original logic in the core MSI code,
but after a deeper analysis it turned out that the quirk flag is not
required at all.
The quirk is only required when the PCI/MSI device cannot mask the MSI
interrupts, which in turn also prevents reservation mode from being enabled
for the affected interrupt.
This allows ot remove the NOMASK quirk bit completely as msi_set_affinity()
can instead check whether reservation mode is enabled for the interrupt,
which gives exactly the same answer.
Even in the momentary non-existing case that the reservation mode would be
not set for a maskable MSI interrupt this would not cause any harm as it
just would cause msi_set_affinity() to go needlessly through the
functionaly equivalent slow path, which works perfectly fine with maskable
interrupts as well.
Rework msi_set_affinity() to query the reservation mode and remove all
NOMASK quirk logic from the core code.
[ tglx: Massaged changelog ]
Fixes: ef8dd01538 ("genirq/msi: Make interrupt allocation less convoluted")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231026032036.2462428-1-den@valinux.co.jp
When a CPU is about to be offlined, x86 validates that all active
interrupts which are targeted to this CPU can be migrated to the remaining
online CPUs. If not, the offline operation is aborted.
The validation uses irq_matrix_allocated() to retrieve the number of
vectors which are allocated on the outgoing CPU. The returned number of
allocated vectors includes also vectors which are associated to managed
interrupts.
That's overaccounting because managed interrupts are:
- not migrated when the affinity mask of the interrupt targets only
the outgoing CPU
- migrated to another CPU, but in that case the vector is already
pre-allocated on the potential target CPUs and must not be taken into
account.
As a consequence the check whether the remaining online CPUs have enough
capacity for migrating the allocated vectors from the outgoing CPU might
fail incorrectly.
Let irq_matrix_allocated() return only the number of allocated non-managed
interrupts to make this validation check correct.
[ tglx: Amend changelog and fixup kernel-doc comment ]
Fixes: 2f75d9e1c9 ("genirq: Implement bitmap matrix allocator")
Reported-by: Wendy Wang <wendy.wang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20231020072522.557846-1-yu.c.chen@intel.com
irq_init_generic_chip() only sets the name for the first chip type, which
leads to empty names for other chip types. Eventually, these names will be
shown as "-" /proc/interrupts.
Set the name for all chip types by default.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230925121734.93017-1-keguang.zhang@gmail.com
Add a kthread_stop_put() helper that stops a thread and puts its task
struct. Use it to replace the various instances of kthread_stop()
followed by put_task_struct().
Remove the kthread_stop_put() macro in usbip that is similar but doesn't
return the result of kthread_stop().
[agruenba@redhat.com: fix kerneldoc comment]
Link: https://lkml.kernel.org/r/20230911111730.2565537-1-agruenba@redhat.com
[akpm@linux-foundation.org: document kthread_stop_put()'s argument]
Link: https://lkml.kernel.org/r/20230907234048.2499820-1-agruenba@redhat.com
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Core:
- Prevent a deadlock of nested interrupt threads vs.
synchronize_hard()
- Removal of a stale extern declaration
Drivers:
- The first new driver since v6.2 for Amlogic-C3 SoCs
- The usual small fixes, cleanups and improvements all over
the place
-----BEGIN PGP SIGNATURE-----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=jiUK
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2023-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Boring updates for the interrupt subsystem:
Core:
- Prevent a deadlock of nested interrupt threads vs.
synchronize_hard()
- Removal of a stale extern declaration
Drivers:
- The first new driver since v6.2 for Amlogic-C3 SoCs
- The usual small fixes, cleanups and improvements all over the
place"
* tag 'irq-core-2023-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Add support for Amlogic-C3 SoCs
dt-bindings: interrupt-controller: Add support for Amlogic-C3 SoCs
irqchip/irq-mvebu-sei: Use devm_platform_get_and_ioremap_resource()
irqchip/ls-scfg-msi: Use devm_platform_get_and_ioremap_resource()
irqchip: Explicitly include correct DT includes
irqchip/orion: Use of_address_count() helper
irqchip/irq-pruss-intc: Do not check for 0 return after calling platform_get_irq()
irqchip/imx-mu-msi: Do not check for 0 return after calling platform_get_irq()
irqchipr/i8259: Mark i8259_of_init() static
irqchip/mips-gic: Mark gic_irq_domain_free() static
irqchip/xtensa-pic: Include header for xtensa_pic_init_legacy()
irqchip/loongson-eiointc: Fix return value checking of eiointc_index
genirq: Remove unused extern declaration
genirq: Prevent nested thread vs synchronize_hardirq() deadlock
The switch to using hlist for managing software resend of interrupts
broke resend in at least two ways:
First, unconditionally adding interrupt descriptors to the resend list can
corrupt the list when the descriptor in question has already been
added. This causes the resend tasklet to loop indefinitely with interrupts
disabled as was recently reported with the Lenovo ThinkPad X13s after
threaded NAPI was disabled in the ath11k WiFi driver.
This bug is easily fixed by restoring the old semantics of irq_sw_resend()
so that it can be called also for descriptors that have already been marked
for resend.
Second, the offending commit also broke software resend of nested
interrupts by simply discarding the code that made sure that such
interrupts are retriggered using the parent interrupt.
Add back the corresponding code that adds the parent descriptor to the
resend list.
Fixes: bc06a9e087 ("genirq: Use hlist for managing resend handlers")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/lkml/20230809073432.4193-1-johan+linaro@kernel.org/
Link: https://lore.kernel.org/r/20230826154004.1417-1-johan+linaro@kernel.org
There is a possibility of deadlock if synchronize_hardirq() is called
when the nested threaded interrupt is active. The following scenario
was observed on a uniprocessor PREEMPT_NONE system:
Thread 1 Thread 2
handle_nested_thread()
Set INPROGRESS
Call ->thread_fn()
thread_fn goes to sleep
free_irq()
__synchronize_hardirq()
Busy-loop forever waiting for INPROGRESS
to be cleared
The INPROGRESS flag is only supposed to be used for hard interrupt
handlers. Remove the incorrect usage in the nested threaded interrupt
case and instead re-use the threads_active / wait_for_threads mechanism
to wait for nested threaded interrupts to complete.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230613-genirq-nested-v3-1-ae58221143eb@axis.com
- A number of Loogson/Loogarch fixes
- Allow the core code to retrigger an interrupt that has
fired while the same interrupt is being handled on another
CPU, papering over a GICv3 architecture issue
- Work around an integration problem on ASR8601, where the CPU
numbering isn't representable in the GIC implementation...
- Add some missing interrupt to the STM32 irqchip
- A bunch of warning squashing triggered by W=1 builds
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAmSWHlEPHG1hekBrZXJu
ZWwub3JnAAoJECPQ0LrRPXpDgDcP/AyuNjjt9ybZ8LT5hGYRBKTfO3bsssiV/ZIE
NRbfwK6nWTurA3tN9XypYouB3HfKvTvDYHzeo9Yi2y51GI20o7noSfVNHHld5dAE
WTBYcfc6n+1KqGNA1tPVeE403jd50TnmOmFaXhN1Vn/KQVQKs+LmjoVdS7HXKmwu
PLk1tbFSGh5+vgLQTlhze5Wz7nU59lJ5WfCJ8negYls/5l3FseGgxEuffWKytElJ
I6PbnRyd9y7R/KYmkobFjS98cjeNznAxJEm/2InVpcb3IwUSEyJUHgNwbs6KSeYf
4BdVyxSAQlFPgxO17UKQxblYu/HuFY/NWghkg7dn6ZgVubj52rtrl9txUId57HGC
pYbSVm0bMevqlgHDYHold+Q4I6DqltyHKgiA9UfU9IQj4MV/KXbDjtng/ih4ZkHe
rw+BnckyrhZ5K5p3nDlzS/TNQT1baKqNFgx/O5HPV27NT8ARynqoFxNUzA0z37v3
x5dj34kiIW2kAGJDOP9+9jj2uF4yX0MKdNxdMs8PM9hYAsO0AqItNsXEQoUuzJF+
u1hhGZ1H6HYmY2WphXD57fnIR/7Hm6Iz00XC17+1jUP+wsefhAbreOyJIbbcpENF
IIxrcIxAPl3PQPsj8n98/9fKQ6u/QfrvWUH+6aoFQH/Np7RTFWmDh8bqucjuXsGS
8gxR3REr
=quHC
-----END PGP SIGNATURE-----
Merge tag 'irqchip-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- A number of Loogson/Loogarch fixes
- Allow the core code to retrigger an interrupt that has
fired while the same interrupt is being handled on another
CPU, papering over a GICv3 architecture issue
- Work around an integration problem on ASR8601, where the CPU
numbering isn't representable in the GIC implementation...
- Add some missing interrupt to the STM32 irqchip
- A bunch of warning squashing triggered by W=1 builds
Link: https://lore.kernel.org/r/20230623224345.3577134-1-maz@kernel.org
* irq/misc-6.5:
: .
: Misc cleanups:
:
: - Add a number of missing prototypes
: - Mark global symbol as static where needed
: - Drop some now useless non-DT code paths
: - Add a missing interrupt mapping to the STM32 irqchip
: - Silence another STM32 warning when building with W=1
: - Fix the jcore-aic driver that actually never worked...
: .
Revert "irqchip/mxs: Include linux/irqchip/mxs.h"
irqchip/jcore-aic: Fix missing allocation of IRQ descriptors
irqchip/stm32-exti: Fix warning on initialized field overwritten
irqchip/stm32-exti: Add STM32MP15xx IWDG2 EXTI to GIC map
irqchip/gicv3: Add a iort_pmsi_get_dev_id() prototype
irqchip/mxs: Include linux/irqchip/mxs.h
irqchip/clps711x: Remove unused clps711x_intc_init() function
irqchip/mmp: Remove non-DT codepath
irqchip/ftintc010: Mark all function static
irqdomain: Include internals.h for function prototypes
Signed-off-by: Marc Zyngier <maz@kernel.org>
irq_domain_debugfs_init() is defined in irqdomain.c, but the
declaration is in a header that is not included here:
kernel/irq/irqdomain.c:1965:13: error: no previous prototype for 'irq_domain_debugfs_init' [-Werror=missing-prototypes]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230516200432.554240-1-arnd@kernel.org
There is a class of interrupt controllers out there that, once they
have signalled a given interrupt number, will still signal incoming
instances of the *same* interrupt despite the original interrupt
not having been EOIed yet.
As long as the new interrupt reaches the *same* CPU, nothing bad
happens, as that CPU still has its interrupts globally disabled,
and we will only take the new interrupt once the interrupt has
been EOIed.
However, things become more "interesting" if an affinity change comes
in while the interrupt is being handled. More specifically, while
the per-irq lock is being dropped. This results in the affinity change
taking place immediately. At this point, there is nothing that prevents
the interrupt from firing on the new target CPU. We end-up with the
interrupt running concurrently on two CPUs, which isn't a good thing.
And that's where things become worse: the new CPU notices that the
interrupt handling is in progress (irq_may_run() return false), and
*drops the interrupt on the floor*.
The whole race looks like this:
CPU 0 | CPU 1
-----------------------------|-----------------------------
interrupt start |
handle_fasteoi_irq | set_affinity(CPU 1)
handler |
... | interrupt start
... | handle_fasteoi_irq -> early out
handle_fasteoi_irq return | interrupt end
interrupt end |
If the interrupt was an edge, too bad. The interrupt is lost, and
the system will eventually die one way or another. Not great.
A way to avoid this situation is to detect this problem at the point
we handle the interrupt on the new target. Instead of dropping the
interrupt, use the resend mechanism to force it to be replayed.
Also, in order to limit the impact of this workaround to the pathetic
architectures that require it, gate it behind a new irq flag aptly
named IRQD_RESEND_WHEN_IN_PROGRESS.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: James Gowans <jgowans@amazon.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: KarimAllah Raslan <karahmed@amazon.com>
Cc: Yipeng Zou <zouyipeng@huawei.com>
Cc: Zhang Jianhua <chris.zjh@huawei.com>
[maz: reworded commit mesage]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230608120021.3273400-3-jgowans@amazon.com
Adding a bit more info about what the flags are used for may help future
code readers.
Signed-off-by: James Gowans <jgowans@amazon.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Liao Chang <liaochang1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230608120021.3273400-2-jgowans@amazon.com
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCZHGVRAAKCRCAXGG7T9hj
vqtJAQDizKasLE7tSnfs/FrZ/4xPaDLe3bQifMx2C1dtYCjRcAD/ciZSa1L0WzZP
dpEZnlYRzsR3bwLktQEMQFOvlbh1SwE=
=K860
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- a double free fix in the Xen pvcalls backend driver
- a fix for a regression causing the MSI related sysfs entries to not
being created in Xen PV guests
- a fix in the Xen blkfront driver for handling insane input data
better
* tag 'for-linus-6.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/pci/xen: populate MSI sysfs entries
xen/pvcalls-back: fix double frees with pvcalls_new_active_socket()
xen/blkfront: Only check REQ_FUA for writes
Commit bf5e758f02 ("genirq/msi: Simplify sysfs handling") reworked the
creation of sysfs entries for MSI IRQs. The creation used to be in
msi_domain_alloc_irqs_descs_locked after calling ops->domain_alloc_irqs.
Then it moved into __msi_domain_alloc_irqs which is an implementation of
domain_alloc_irqs. However, Xen comes with the only other implementation
of domain_alloc_irqs and hence doesn't run the sysfs population code
anymore.
Commit 6c796996ee ("x86/pci/xen: Fixup fallout from the PCI/MSI
overhaul") set the flag MSI_FLAG_DEV_SYSFS for the xen msi_domain_info
but that doesn't actually have an effect because Xen uses it's own
domain_alloc_irqs implementation.
Fix this by making use of the fallback functions for sysfs population.
Fixes: bf5e758f02 ("genirq/msi: Simplify sysfs handling")
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20230503131656.15928-1-mheyne@amazon.de
Signed-off-by: Juergen Gross <jgross@suse.com>
The current implementation uses a static bitmap for interrupt descriptor
allocation and a radix tree to pointer store the pointer for lookup.
However, the size of the bitmap is constrained by the build time macro
MAX_SPARSE_IRQS, which may not be sufficient to support high-end servers,
particularly those with GICv4.1 hardware, which require a large interrupt
space to cover LPIs and vSGIs.
Replace the bitmap and the radix tree with a maple tree, which not only
stores pointers for lookup, but also provides a mechanism to find free
ranges. That removes the build time hardcoded upper limit.
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230519134902.1495562-4-sdonthineni@nvidia.com
Move the open coded sparse bitmap handling into helper functions as
a preparatory step for converting the sparse interrupt management
to a maple tree.
No functional change.
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230519134902.1495562-3-sdonthineni@nvidia.com
The current implementation utilizes a bitmap for managing interrupt resend
handlers, which is allocated based on the SPARSE_IRQ/NR_IRQS macros.
However, this method may not efficiently utilize memory during runtime,
particularly when IRQ_BITMAP_BITS is large.
Address this issue by using an hlist to manage interrupt resend handlers
instead of relying on a static bitmap memory allocation. Additionally, a
new function, clear_irq_resend(), is introduced and called from
irq_shutdown to ensure a graceful teardown of the interrupt.
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230519134902.1495562-2-sdonthineni@nvidia.com
For interrupts with secondary threads, the affinity is applied when the
thread is created but if the interrupts affinity is changed later only
the primary thread is updated.
Update the secondary thread's affinity as well to keep all the interrupts
activity on the assigned CPUs.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230406180857.588682-1-john@metanate.com
- Prevent possible NULL pointer derefences in irq_data_get_affinity_mask()
and irq_domain_create_hierarchy().
- Take the per device MSI lock before invoking code which relies
on it being hold.
- Make sure that MSI descriptors are unreferenced before freeing
them. This was overlooked when the platform MSI code was converted to
use core infrastructure and results in a fals positive warning.
- Remove dead code in the MSI subsystem.
- Clarify the documentation for pci_msix_free_irq().
- More kobj_type constification.
-----BEGIN PGP SIGNATURE-----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=jWot
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2023-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"A set of updates for the interrupt susbsystem:
- Prevent possible NULL pointer derefences in
irq_data_get_affinity_mask() and irq_domain_create_hierarchy()
- Take the per device MSI lock before invoking code which relies on
it being hold
- Make sure that MSI descriptors are unreferenced before freeing
them. This was overlooked when the platform MSI code was converted
to use core infrastructure and results in a fals positive warning
- Remove dead code in the MSI subsystem
- Clarify the documentation for pci_msix_free_irq()
- More kobj_type constification"
* tag 'irq-urgent-2023-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi, platform-msi: Ensure that MSI descriptors are unreferenced
genirq/msi: Drop dead domain name assignment
irqdomain: Add missing NULL pointer check in irq_domain_create_hierarchy()
genirq/irqdesc: Make kobj_type structures constant
PCI/MSI: Clarify usage of pci_msix_free_irq()
genirq/msi: Take the per-device MSI lock before validating the control structure
genirq/ipi: Fix NULL pointer deref in irq_data_get_affinity_mask()
Miquel reported a warning in the MSI core which is triggered when
interrupts are freed via platform_msi_device_domain_free().
This code got reworked to use core functions for freeing the MSI
descriptors, but nothing took care to clear the msi_desc->irq entry, which
then triggers the warning in msi_free_msi_desc() which uses desc->irq to
validate that the descriptor has been torn down. The same issue exists in
msi_domain_populate_irqs().
Up to the point that msi_free_msi_descs() grew a warning for this case,
this went un-noticed.
Provide the counterpart of msi_domain_populate_irqs() and invoke it in
platform_msi_device_domain_free() before freeing the interrupts and MSI
descriptors and also in the error path of msi_domain_populate_irqs().
Fixes: 2f2940d168 ("genirq/msi: Remove filter from msi_free_descs_free_range()")
Reported-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87mt4wkwnv.ffs@tglx
Some polishing and small fixes for iommufd:
- Remove IOMMU_CAP_INTR_REMAP, instead rely on the interrupt subsystem
- Use GFP_KERNEL_ACCOUNT inside the iommu_domains
- Support VFIO_NOIOMMU mode with iommufd
- Various typos
- A list corruption bug if HWPTs are used for attach
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCY/TgzQAKCRCFwuHvBreF
Ya3AAP4/WxTJIbDvtTyH3Fae3NxTdO8j8gsUvU1vrRYG83zdnAEAxd1yii7GEO8D
crkeq9D4FUiPAkFnJ64Exw2FHb060Qg=
=RABK
-----END PGP SIGNATURE-----
Merge tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd
Pull iommufd updates from Jason Gunthorpe:
"Some polishing and small fixes for iommufd:
- Remove IOMMU_CAP_INTR_REMAP, instead rely on the interrupt
subsystem
- Use GFP_KERNEL_ACCOUNT inside the iommu_domains
- Support VFIO_NOIOMMU mode with iommufd
- Various typos
- A list corruption bug if HWPTs are used for attach"
* tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd:
iommufd: Do not add the same hwpt to the ioas->hwpt_list twice
iommufd: Make sure to zero vfio_iommu_type1_info before copying to user
vfio: Support VFIO_NOIOMMU with iommufd
iommufd: Add three missing structures in ucmd_buffer
selftests: iommu: Fix test_cmd_destroy_access() call in user_copy
iommu: Remove IOMMU_CAP_INTR_REMAP
irq/s390: Add arch_is_isolated_msi() for s390
iommu/x86: Replace IOMMU_CAP_INTR_REMAP with IRQ_DOMAIN_FLAG_ISOLATED_MSI
genirq/msi: Rename IRQ_DOMAIN_MSI_REMAP to IRQ_DOMAIN_ISOLATED_MSI
genirq/irqdomain: Remove unused irq_domain_check_msi_remap() code
iommufd: Convert to msi_device_has_isolated_msi()
vfio/type1: Convert to iommu_group_has_isolated_msi()
iommu: Add iommu_group_has_isolated_msi()
genirq/msi: Add msi_device_has_isolated_msi()
Since commit d59f6617ee ("genirq: Allow fwnode to carry name
information only") an IRQ domain is always given a name during
allocation (e.g. used for the debugfs entry).
Drop the unused fallback name assignment when creating MSI domains.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230224130509.27814-1-johan+linaro@kernel.org
The recent switch to per-domain locking caused a NULL dereference in
irq_domain_create_hierarchy(), as Xen code is calling
msi_create_irq_domain() with a NULL parent pointer.
Fix that by testing parent to be set before dereferencing it. For a
non-existing parent the irqdomain's root will stay to point to
itself.
Fixes: 9dbb8e3452 ("irqdomain: Switch to per-domain locking")
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230223083800.31347-1-jgross@suse.com
Core:
- Move the interrupt affinity spreading mechanism into lib/group_cpus
so it can be used for similar spreading requirements, e.g. in the
block multi-queue code.
This also contains a first usecase in the block multi-queue code which
Jens asked to take along with the librarization.
- Improve irqdomain locking to close a number race conditions which
can be observed with massive parallel device driver probing.
- Enforce and document the semantics of disable_irq() which cannot be
invoked safely from non-sleepable context.
- Move the IPI multiplexing code from the Apple AIC driver into the
core. so it can be reused by RISCV.
Drivers:
- Plug OF node refcounting leaks in various drivers.
- Correctly mark level triggered interrupts in the Broadcom L2 drivers.
- The usual small fixes and improvements.
- No new drivers for the record!
-----BEGIN PGP SIGNATURE-----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=+pu3
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2023-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core:
- Move the interrupt affinity spreading mechanism into lib/group_cpus
so it can be used for similar spreading requirements, e.g. in the
block multi-queue code
This also contains a first usecase in the block multi-queue code
which Jens asked to take along with the librarization
- Improve irqdomain locking to close a number race conditions which
can be observed with massive parallel device driver probing
- Enforce and document the semantics of disable_irq() which cannot be
invoked safely from non-sleepable context
- Move the IPI multiplexing code from the Apple AIC driver into the
core, so it can be reused by RISCV
Drivers:
- Plug OF node refcounting leaks in various drivers
- Correctly mark level triggered interrupts in the Broadcom L2
drivers
- The usual small fixes and improvements
- No new drivers for the record!"
* tag 'irq-core-2023-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (42 commits)
irqchip/irq-bcm7120-l2: Set IRQ_LEVEL for level triggered interrupts
irqchip/irq-brcmstb-l2: Set IRQ_LEVEL for level triggered interrupts
irqdomain: Switch to per-domain locking
irqchip/mvebu-odmi: Use irq_domain_create_hierarchy()
irqchip/loongson-pch-msi: Use irq_domain_create_hierarchy()
irqchip/gic-v3-mbi: Use irq_domain_create_hierarchy()
irqchip/gic-v3-its: Use irq_domain_create_hierarchy()
irqchip/gic-v2m: Use irq_domain_create_hierarchy()
irqchip/alpine-msi: Use irq_domain_add_hierarchy()
x86/uv: Use irq_domain_create_hierarchy()
x86/ioapic: Use irq_domain_create_hierarchy()
irqdomain: Clean up irq_domain_push/pop_irq()
irqdomain: Drop leftover brackets
irqdomain: Drop dead domain-name assignment
irqdomain: Drop revmap mutex
irqdomain: Fix domain registration race
irqdomain: Fix mapping-creation race
irqdomain: Refactor __irq_domain_alloc_irqs()
irqdomain: Look for existing mapping only once
irqdomain: Drop bogus fwspec-mapping error handling
...
Since commit ee6d3dd4ed ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definitions which prevents
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230217-kobj_type-irq-v1-1-fedfacaf8cdb@weissschuh.net
Calling msi_ctrl_valid() ultimately results in calling
msi_get_device_domain(), which requires holding the device MSI lock.
However, in msi_domain_populate_irqs() the lock is taken right after having
called msi_ctrl_valid(), which is just a tad too late.
Take the lock before invoking msi_ctrl_valid().
Fixes: 40742716f2 ("genirq/msi: Make msi_add_simple_msi_descs() device domain aware")
Reported-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/Y/Opu6ETe3ZzZ/8E@shell.armlinux.org.uk
Link: https://lore.kernel.org/r/20230220190101.314446-1-maz@kernel.org
