PRSNT_MAP bit field is programmed to update the slot present status.
PRSNT_SENSE IRQ is triggered when this bit field is programmed, which is
not an error. Add a new if condition to trap PRSNT_SENSE code and print
it with debug log level.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cacheable upstream transactions are supported in Tegra20 and Tegra186
only.
AFI_CACHE_BAR_{0,1}_{ST,SZ} registers are available in Tegra20 to
support cacheable upstream transactions. In Tegra186, AFI_AXCACHE
register is defined instead of AFI_CACHE_BAR_{0,1}_{ST,SZ} to be in line
with its memory subsystem design.
Therefore, program AFI_CACHE_BAR_{0,1}_{ST,SZ} registers only for Tegra20.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Disable controllers which failed to bring the link up and configure
CLKREQ# signals of these controllers as GPIO. This is required to avoid
CLKREQ# signal of inactive controllers interfering with PLLE power down
sequence.
PCIE_CLKREQ_GPIO bits are defined only in Tegra186, however programming
these bits in other SoCs doesn't cause any side effects. Program these
bits for all Tegra SoCs to avoid a conditional check.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
PCIe link up fails with few legacy endpoints if root port advertises both
Gen-1 and Gen-2 speeds in Tegra. This is because link number negotiation
fails if both Gen1 & Gen2 are advertised. Tegra doesn't retry link up by
advertising only Gen1. Hence, the strategy followed here is to initially
advertise only Gen-1 and after link is up, retrain link to Gen-2 speed.
Tegra doesn't support HW autonomous speed change. Link comes up in Gen1
even if Gen2 is advertised, so there is no downside of this change.
This behavior is observed with following two PCIe devices on Tegra:
- Fusion HDTV 5 Express card
- IOGear SIL - PCIE - SATA card
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Recommended UpdateFC threshold in Tegra210 is 0x60 for best performance
of x1 link. Setting this to 0x60 provides the best balance between number
of UpdateFC packets and read data sent over the link.
UpdateFC timer frequency is equal to twice the value of register content
in nsec, i.e (2 * 0x60) = 192 nsec.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The logic which blocks read requests till AFI gets ACK for all outstanding
writes from memory controller does not behave correctly when number of
outstanding writes become more than 32 in Tegra124 and Tegra132.
SW fixup is to prevent writes from accumulating more than 32 by:
- limiting outstanding posted writes to 14
- modifying Gen1 and Gen2 UpdateFC timer frequency
UpdateFC timer frequency is equal to twice the value of register content
in nsec. These settings are recommended after stress testing with
different values.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Sometimes link speed change from Gen2 to Gen1 fails due to instability
in deskew logic on lane-0 in Tegra210. Increase the deskew retry time
to resolve this issue.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Enable xclk clock clamping when entering L1. Clamp threshold will
determine the time spent waiting for clock module to turn on xclk after
signaling it. Default threshold value in Tegra124 and Tegra210 is not
enough to turn on xclk clock. Increase the clamp threshold to meet the
clock module timing in Tegra124 and Tegra210. Default threshold value is
enough in Tegra20, Tegra30 and Tegra186.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
PM message are truncated while entering L1 or L2, which is resulting in
receiver errors. Set the required bit to finish processing DLLP before
link enter L1 or L2.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Outstanding write counter in AFI is used to generate idle signal to
dynamically gate the AFI clock. When there are 32 outstanding writes
from AFI to memory, the outstanding write counter overflows and
indicates that there are "0" outstanding write transactions.
When memory controller is under heavy load, write completions to AFI
gets delayed and AFI write counter overflows. This causes AFI clock gating
even when there are outstanding transactions towards memory controller
resulting in a system hang.
Disable dynamic clock gating of AFI clock to avoid system hang.
CLKEN_OVERRIDE bit is not defined in Tegra20 and Tegra30, however
programming this bit doesn't cause any side effects. Program this
bit for all Tegra SoCs to avoid conditional check.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Enable opportunistic UpdateFC and ACK to allow data link layer send
pending ACKs and UpdateFC packets when link is idle instead of waiting
for timers to expire. This improves the PCIe performance due to better
utilization of PCIe bandwidth.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
UPHY electrical programming guidelines are documented in Tegra210 TRM.
Program these electrical settings for proper eye diagram in Gen1 and Gen2
link speeds.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Default root port setting hides AER capability. This patch enables the
advertisement of AER capability by root port.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra124, Tegra132, Tegra210 and Tegra186 support Gen2 link speed. After
PCIe link is up in Gen1, set target link speed as Gen2 and retrain link.
Link switches to Gen2 speed if Gen2 capable end point is connected,
otherwise the link stays in Gen1.
Per PCIe 4.0r0.9 sec 7.6.3.7 implementation note, driver needs to wait for
PCIe LTSSM to come back from recovery before retraining the link.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The PCIe host power up sequence requires to program AFI(AXI to FPCI
bridge) registers first and then PCIe registers, otherwise AFI register
settings may not latch to PCIe IP.
PCIe root port starts LTSSM as soon as PCIe xrst is deasserted.
So deassert PCIe xrst after programming PCIe registers.
Modify PCIe power up sequence as follows:
- Power ungate PCIe partition
- Enable AFI clock
- Deassert AFI reset
- Program AFI registers
- Enable PCIe clock
- Deassert PCIe reset
- Program PCIe PHY
- Program PCIe pad control registers
- Program PCIe root port registers
- Deassert PCIe xrst to start LTSSM
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tegra PCIe has register specifications for:
- AXI to FPCI(AFI) bridge
- Multiple PCIe root ports
- PCIe PHY
- PCIe pad control
Rearrange Tegra PCIe driver functions so that each function programs
the required module only.
- tegra_pcie_enable_controller(): Program AFI module and enable PCIe
controller
- tegra_pcie_phy_power_on(): Bring up PCIe PHY
- tegra_pcie_apply_pad_settings(): Program PCIe REFCLK pad settings
- tegra_pcie_enable_ports(): Program each root port and bring up PCIe
link
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Unroll the PCIe power on sequence if any one of the steps fails in
tegra_pcie_power_on().
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
- Use DMA-API to get tegra MSI address to prevent device DMA from
generating unwanted MSIs (Vidya Sagar)
* remotes/lorenzo/pci/tegra:
PCI: tegra: Use the DMA-API to get the MSI address
- Move IRQ register address computation inside macros (Kishon Vijay
Abraham I)
- Separate legacy IRQ and MSI configuration (Kishon Vijay Abraham I)
- Use hwirq, not virq, to get MSI IRQ number offset (Kishon Vijay Abraham
I)
- Squash ks_pcie_handle_msi_irq() into ks_pcie_msi_irq_handler() (Kishon
Vijay Abraham I)
- Add dwc support for platforms with custom MSI controllers (Kishon Vijay
Abraham I)
- Add keystone-specific MSI controller (Kishon Vijay Abraham I)
- Remove dwc host_ops previously used for keystone-specific MSI (Kishon
Vijay Abraham I)
- Skip dwc default MSI init if platform has custom MSI controller (Kishon
Vijay Abraham I)
- Implement .start_link() and .stop_link() for keystone endpoint support
(Kishon Vijay Abraham I)
- Add keystone "reg-names" DT binding (Kishon Vijay Abraham I)
- Squash ks_pcie_dw_host_init() into ks_pcie_add_pcie_port() (Kishon
Vijay Abraham I)
- Get keystone register resources from DT by name, not index (Kishon
Vijay Abraham I)
- Get DT resources in .probe() to prepare for endpoint support (Kishon
Vijay Abraham I)
- Add "ti,syscon-pcie-mode" DT property for PCIe mode configuration
(Kishon Vijay Abraham I)
- Explicitly set keystone to host mode (Kishon Vijay Abraham I)
- Document DT "atu" reg-names requirement for DesignWare core >= 4.80
(Kishon Vijay Abraham I)
- Enable dwc iATU unroll for endpoint mode as well as host mode (Kishon
Vijay Abraham I)
- Add dwc "version" to identify core >= 4.80 for ATU programming (Kishon
Vijay Abraham I)
- Don't build ARM32-specific keystone code on ARM64 (Kishon Vijay Abraham
I)
- Add DT binding for keystone PCIe RC in AM654 SoC (Kishon Vijay Abraham
I)
- Add keystone support for AM654 SoC PCIe RC (Kishon Vijay Abraham I)
- Reset keystone PHYs before enabling them (Kishon Vijay Abraham I)
- Make of_pci_get_max_link_speed() available to endpoint drivers as well
as host drivers (Kishon Vijay Abraham I)
- Add keystone support for DT "max-link-speed" property (Kishon Vijay
Abraham I)
- Add endpoint library support for BAR buffer alignment (Kishon Vijay
Abraham I)
- Make all dw_pcie_ep_ops structs const (Kishon Vijay Abraham I)
- Fix fencepost error in dw_pcie_ep_find_capability() (Kishon Vijay
Abraham I)
- Add dwc hooks for dbi/dbi2 that share the same address space (Kishon
Vijay Abraham I)
- Add keystone support for TI AM654x in endpoint mode (Kishon Vijay
Abraham I)
- Configure designware endpoints to advertise smallest resizable BAR
(1MB) (Kishon Vijay Abraham I)
- Align designware endpoint ATU windows for raising MSIs (Kishon Vijay
Abraham I)
- Add endpoint test support for TI AM654x (Kishon Vijay Abraham I)
- Fix endpoint test test_reg_bar issue (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
misc: pci_endpoint_test: Fix test_reg_bar to be updated in pci_endpoint_test
misc: pci_endpoint_test: Add support to test PCI EP in AM654x
PCI: designware-ep: Use aligned ATU window for raising MSI interrupts
PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size
PCI: keystone: Add support for PCIe EP in AM654x Platforms
dt-bindings: PCI: Add PCI EP DT binding documentation for AM654
PCI: dwc: Add callbacks for accessing dbi2 address space
PCI: dwc: Fix dw_pcie_ep_find_capability() to return correct capability offset
PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops
PCI: endpoint: Add support to specify alignment for buffers allocated to BARs
PCI: keystone: Add support to set the max link speed from DT
PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint drivers
PCI: keystone: Invoke phy_reset() API before enabling PHY
PCI: keystone: Add support for PCIe RC in AM654x Platforms
dt-bindings: PCI: Add PCI RC DT binding documentation for AM654
PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64
PCI: dwc: Fix ATU identification for designware version >= 4.80
PCI: dwc: Enable iATU unroll for endpoint too
dt-bindings: PCI: Document "atu" reg-names
PCI: keystone: Explicitly set the PCIe mode
dt-bindings: PCI: Add dt-binding to configure PCIe mode
PCI: keystone: Move resources initialization to prepare for EP support
PCI: keystone: Use platform_get_resource_byname() to get memory resources
PCI: keystone: Perform host initialization in a single function
dt-bindings: PCI: keystone: Add "reg-names" binding information
PCI: keystone: Cleanup error_irq configuration
PCI: keystone: Add start_link()/stop_link() dw_pcie_ops
PCI: dwc: Remove default MSI initialization for platform specific MSI chips
PCI: dwc: Remove Keystone specific dw_pcie_host_ops
PCI: keystone: Use Keystone specific msi_irq_chip
PCI: dwc: Add support to use non default msi_irq_chip
PCI: keystone: Cleanup ks_pcie_msi_irq_handler()
PCI: keystone: Use hwirq to get the MSI IRQ number offset
PCI: keystone: Add separate functions for configuring MSI and legacy interrupt
PCI: keystone: Cleanup interrupt related macros
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
- Work around iproc CRS completion issues (Srinath Mannam)
- Allow smaller iproc outbound windows so driver can work on 32-bit
systems (Srinath Mannam)
- Use iproc-specific config read for PAXBv2 (not PAXB) (Srinath Mannam)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Enable iProc config read for PAXBv2
PCI: iproc: Allow outbound configuration for 32-bit I/O region
PCI: iproc: Add CRS check in config read
- Simplify imx7d_pcie_wait_for_phy_pll_lock() by using
regmap_read_poll_timeout() (Andrey Smirnov)
- Drop imx6_pcie_wait_for_link() in favor of the more generic
dw_pcie_wait_for_link() (Andrey Smirnov)
- Return -ETIMEDOUT instead of -EINVAL from
imx6_pcie_wait_for_speed_change() (Andrey Smirnov)
- Remove unused PCIE_PL_PFLR_* constants from imx6 (Andrey Smirnov)
- Use shared PHY debug register definitions in imx6 (Andrey Smirnov)
- Use BIT() in imx6 (Andrey Smirnov)
- Simplify imx6 PHY bit operations (Andrey Smirnov)
- Simplify imx6 pcie_phy_poll_ack() (Andrey Smirnov)
- Use data types that match actual imx6 PHY register width (Andrey
Smirnov)
- Mark imx6 suspend support with drvdata flags instead of checking
variants (Andrey Smirnov)
- Sleep instead of delay in imx6_pcie_enable_ref_clk() (Andrey Smirnov)
* remotes/lorenzo/pci/imx:
PCI: imx6: Use usleep_range() in imx6_pcie_enable_ref_clk()
PCI: imx6: Use flags to indicate support for suspend
PCI: imx6: Restrict PHY register data to 16-bit
PCI: imx6: Simplify pcie_phy_poll_ack()
PCI: imx6: Simplify bit operations in PHY functions
PCI: imx6: Make use of BIT() in constant definitions
PCI: dwc: imx6: Share PHY debug register definitions
PCI: imx6: Remove PCIE_PL_PFLR_* constants
PCI: imx6: Return -ETIMEOUT from imx6_pcie_wait_for_speed_change()
PCI: imx6: Drop imx6_pcie_wait_for_link()
PCI: imx6: Simplify imx7d_pcie_wait_for_phy_pll_lock()
- Restore R-Car PCIe link early in resume (Kazufumi Ikeda)
- Fix Hyper-V PCI ejection memory leak (Dexuan Cui)
- Cleanup Hyper-V PCI slots on module unload (Dexuan Cui)
- Cleanup Hyper-V PCI slot on device removal to address a race (Dexuan
Cui)
* remotes/lorenzo/pci/controller-fixes:
PCI: hv: Add pci_destroy_slot() in pci_devices_present_work(), if necessary
PCI: hv: Add hv_pci_remove_slots() when we unload the driver
PCI: hv: Fix a memory leak in hv_eject_device_work()
PCI: rcar: Add the initialization of PCIe link in resume_noirq()
Establishing a PCIe link can take a while; allow asynchronous probing so
that link establishment can happen in the background while other devices
are being probed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently DWC host does not support the remove callback, but nothing
prevents us from supporting it.
Save the root bus for clean up work in driver remove code paths to allow
DWC host drivers to implement their remove hook as, eg:
static int foo_pcie_remove(struct platform_device *pdev)
{
...
pci_stop_root_bus(pp->root_bus);
pci_remove_root_bus(pp->root_bus);
dw_pcie_free_msi(pp);
...
}
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Use devm_pci_alloc_host_bridge() to simplify the error code path. This
also fixes a leak in the dw_pcie_host_init() error path.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
CC: stable@vger.kernel.org # v4.13+
If we ever did MSI-related initializations, we need to call
dw_pcie_free_msi() in the error code path.
Remove the IS_ENABLED(CONFIG_PCI_MSI) check for MSI init because
pci_msi_enabled() already has a stub for !CONFIG_PCI_MSI.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
To avoid a memory leak, free the page allocated for MSI IRQ in
dw_pcie_free_msi().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Check msi_irq variable before calling irq_set_chained_handler() and
irq_set_handler_data(), lest we call those functions for an invalid MSI
IRQ.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Move the device class fudge to a proper fixup function, and remove
qcom_pcie_rd_own_conf() which has become useless.
dw_pcie_setup_rc() already did the right thing, but it's broken
on older qcom chips, such as 8064.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The iProc host controller allows only a subset of physical address space as
target of inbound PCI memory transaction addresses.
PCI device memory transactions targeting memory regions that are not
allowed for inbound transactions in the host controller are rejected by the
host controller and cannot reach the upstream buses.
The firmware device tree description defines the DMA ranges that are
addressable by devices DMA transactions; parse the device tree dma-ranges
property and add its ranges to the PCI host bridge dma_ranges list; the
iova_reserve_pci_windows() call executed at iommu_dma_init_domain() will
reserve the IOVA address ranges that are not addressable (ie memory holes
in the dma-ranges set) so that they are not allocated to PCI devices for
DMA transfers.
All allowed address ranges are listed in the dma-ranges DT parameter. For
example:
dma-ranges = < \
0x43000000 0x00 0x80000000 0x00 0x80000000 0x00 0x80000000 \
0x43000000 0x08 0x00000000 0x08 0x00000000 0x08 0x00000000 \
0x43000000 0x80 0x00000000 0x80 0x00000000 0x40 0x00000000>
In the above example of dma-ranges, memory address from
0x0 - 0x80000000,
0x100000000 - 0x800000000,
0x1000000000 - 0x8000000000 and
0x10000000000 - 0xffffffffffffffff.
are not allowed to be used as inbound addresses.
Based-on-a-patch-by: Oza Pawandeep <oza.oza@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: fix function prototype style]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Certain platforms like K2G reguires the outbound ATU window to be
aligned. The alignment size is already present in mem->page_size.
Use the alignment size present in mem->page_size to configure an
aligned ATU window. In order to raise an interrupt, CPU has to write
to address offset from the start of the window unlike before where
writes were always to the beginning of the ATU window.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Configure the Resizable BAR capability to advertise the smallest size
(1MB) for a couple of reasons:
- Host side resource allocation of BAR fails for larger sizes
- Endpoint function driver does not allocate memory for all supported
sizes in the Resizable BAR capability.
If and when there is a usecase required to add more flexibility using
the Resizable BAR capability, this can be revisited.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add PCIe EP support for AM654x Platforms in pci-keystone.c
Link: https://lore.kernel.org/linux-pci/20190325093947.32633-15-kishon@ti.com/
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: made dev_vdbg() call a comment]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
imx6_pcie_enable_ref_clk() is never called in atomic context, so
there's no need to use udelay(). Replace it with usleep_range().
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Now that driver data has flags variable that can be used to indicate
quirks/features supported we can switch the code to use it instead of
having a special function that does so based on variant alone. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
PHY registers on i.MX6 are 16-bit wide, so we can get rid of explicit
masking if we restrict pcie_phy_read()/pcie_phy_write() to use 'u16'
instead of 'int'. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Simplify pcie_phy_poll_ack() by incorporating shifting into constant
definition and convert the code to use 'bool'. No functional change
intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Simplify the code by incorporating left shifts into constant
definitions as well as using FIELD_PREP/GENMASK. No functional change
intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Avoid using explicit left shifts and convert various definitions to
use BIT() instead. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
