Those have little value. Remove those to
make the driver less noisy.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some platforms are incapable of triggering on level interrupts. Add a
platform quirks member in the platform data structure, as well as an
edge interrupt quirk which can be set on such platforms.
When the interrupt is requested with IRQF_TRIGGER_RISING, IRQF_ONESHOT
cannot be used, as we might miss interrupts that occur after the FW
status is cleared and before the threaded interrupt handler exits.
Moreover, when IRQF_ONESHOT is not set, iterating more than once in the
threaded interrupt handler introduces a few race conditions between this
handler and the hardirq handler. Currently this is worked around by
limiting the loop to one iteration only. This workaround has an impact
on performance. To remove to this restriction, the race conditions will
need to be addressed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Choose a different FW for AP-mode wl127x and wl128x chips, base on chip
ID at boot time.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Boot sequence support FREF clock and TCXO clock.
WL128x has two clocks input - TCXO and FREF.
TCXO is the main clock of the device, while FREF is used to sync
between the GPS and the cellular modem.
Auto-detection checks where TCXO is 32.736MHz or 16.368MHz, in that
case the FREF will be used as the WLAN/BT main clock.
[Use clock enumeration as defined in linux/wl12xx.h; remove
unnecessary else block in wl128x_switch_fref; remove unnecessary
change in main.c; remove some unnecessary debug prints and comments;
fix potential use of uninitialized value (pll_config) -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the the set_block_size op in the SDIO and in the SPI modules.
Since it is only used with SDIO, just explicitly set the op to NULL in
spi.c
Signed-off-by: Luciano Coelho <coelho@ti.com>
Definitions to support wl128x:
- New FW file name
- Chip ID
- New PLL Configuration Algorithm macros that will be used at wl128x
boot stage
- Rename NVS macro name: wl127x and wl128x are using the same NVS
file name. However, the ini parameters between them are
different. The driver will validate the correct NVS size in
wl1271_boot_upload_nvs().
[Cleaned up some of the definitions. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The MODULE_AUTHOR() macro in the main module (wl12xx) has been updated
to reflect one of the author's new email address, but the wl12xx_spi
and wl12xx_sdio modules haven't been updated. This patches updates
them.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt of the wl12xx is a level interrupt in nature, since the
interrupt line is not auto-reset. However, since resetting the interrupt
requires bus transactions, this cannot be done from an interrupt
context. Thus, requesting a level interrupt would require to disable the
irq and re-enable it after the HW is acknowledged. Since we now request
a threaded irq, this can also be done by specifying the IRQF_ONESHOT
flag.
Triggering on an edge can be problematic in some platforms, if the
sampling frequency is not sufficient for detecting very frequent
interrupts. In case an interrupt is missed, the driver will hang as the
interrupt line will stay high until it is acknowledged by the driver,
which will never happen.
Fix this by requesting a level triggered interrupt, with the
IRQF_ONESHOT flag.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
To achieve maximal throughput, it is very important to react to
interrupts as soon as possible. Currently the interrupt handler wakes up
a worker for handling interrupts in process context. A cleaner and more
efficient design would be to request a threaded interrupt handler. This
handler's priority is very high, and can do blocking operations such as
SDIO/SPI transactions.
Some work can be deferred, mostly calls to mac80211 APIs
(ieee80211_rx_ni and ieee80211_tx_status). By deferring such work to a
different worker, we can keep the irq handler thread more I/O
responsive. In addition, on multi-core systems the two threads can be
scheduled on different cores, which will improve overall performance.
The use of WL1271_FLAG_IRQ_PENDING & WL1271_FLAG_IRQ_RUNNING was
changed. For simplicity, always query the FW for more pending
interrupts. Since there are relatively long bursts of interrupts, the
extra FW status read overhead is negligible. In addition, this enables
registering the IRQ handler with the ONESHOT option.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In wl12xx cards AP-mode requires a separate FW file. Add this file to
the module info.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If debugging is turned on, then wl1271_dump() dereferences a freed
variable.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
All files name prefix removed due to the fact that wl12xx driver supports
wl1271 and wl1273.
Also the definition in Kconfig and header files changed respectively.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Now that all 1271 files are split, we can add wl1251_ prefix to the files.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for block reading (multiple bytes) from a fixed chipset
register address. This is required for the wl1271 TX data path.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wl1271 implementation, we need to read memory from the register
partition using fixed addresses. This change adds the possibility to request
fixed address when calling wl12xx_spi_read() or wl12xx_spi_reg_read().
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases we need to read more than 32 bits from the register area.
These functions were added to support that, like the existing
wl12xx_spi_mem_read() and wl12xx_spi_mem_write() already do for large blocks
in the memory area.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl12xx is a driver for TI wl1251 802.11 chipset designed for embedded
devices, supporting both SDIO and SPI busses. Currently the driver
supports only SPI. Adding support 1253 (the 5 GHz version) should be
relatively easy. More information here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?contentId=4711&navigationId=12494&templateId=6123
(Collapsed original sequence of pre-merge patches into single commit for
initial merge. -- JWL)
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
