By default, the DMA mask covers only the low 32-bit address space, which
causes SWIOTLB on arm64 to fall back to a bounce buffer for DMA
transfers involving memory outside the 32-bit address space.
The R-Car DMA controller hardware supports a 40-bit address space, hence
widen the DMA mask to 40 bits to actually make use of this feature.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Despite the CPPI 4.1 is a generic DMA, it is tied to USB.
On the DSPS, CPPI 4.1 interrupt's registers are in USBSS (the MUSB glue).
Currently, to enable / disable and clear interrupts, the CPPI 4.1 driver
maps and accesses to USBSS's register, which making CPPI 4.1 driver not
really generic.
Move the interrupt management to DSPS driver.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As 64-bit Allwinner H5 SoC has the same DMA engine with H3, the DMA
driver should be allowed to be built for ARM64, in order to make it work on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The static bug finder EBA (http://www.iagoabal.eu/eba/) reported the
following double-lock bug:
Double lock:
1. spin_lock_irqsave(pch->lock, flags) at pl330_free_chan_resources:2236;
2. call to function `pl330_release_channel' immediately after;
3. call to function `dma_pl330_rqcb' in line 1753;
4. spin_lock_irqsave(pch->lock, flags) at dma_pl330_rqcb:1505.
I have fixed it as suggested by Marek Szyprowski.
First, I have replaced `pch->lock' with `pl330->lock' in functions
`pl330_alloc_chan_resources' and `pl330_free_chan_resources'. This avoids
the double-lock by acquiring a different lock than `dma_pl330_rqcb'.
NOTE that, as a result, `pl330_free_chan_resources' executes
`list_splice_tail_init' on `pch->work_list' under lock `pl330->lock',
whereas in the rest of the code `pch->work_list' is protected by
`pch->lock'. I don't know if this may cause race conditions. Similarly
`pch->cyclic' is written by `pl330_alloc_chan_resources' under
`pl330->lock' but read by `pl330_tx_submit' under `pch->lock'.
Second, I have removed locking from `pl330_request_channel' and
`pl330_release_channel' functions. Function `pl330_request_channel' is
only called from `pl330_alloc_chan_resources', so the lock is already
held. Function `pl330_release_channel' is called from
`pl330_free_chan_resources', which already holds the lock, and from
`pl330_del'. Function `pl330_del' is called in an error path of
`pl330_probe' and at the end of `pl330_remove', but I assume that there
cannot be concurrent accesses to the protected data at those points.
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix build warning that related to PAGE_SIZE. The maximum DMA
length has nothing to do with PAGE_SIZE, just use a fix number
for the definition.
drivers/dma/zx_dma.c: In function 'zx_dma_prep_memcpy':
drivers/dma/zx_dma.c:523:8: warning: division by zero [-Wdiv-by-zero]
drivers/dma/zx_dma.c: In function 'zx_dma_prep_slave_sg':
drivers/dma/zx_dma.c:567:11: warning: division by zero [-Wdiv-by-zero]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Intel Merrifield platform contains Intel integrated DMA (iDMA 32-bit) which has
a slightly different register mapping, e.g. some bits in CTL_* and CFG_*
channel registers, and has to use platform data since there is no
autoconfiguration.
The iDMA 32-bit specification is available in the publicly available
documentation for Intel Braswell and BayTrail SoCs as LPE Audio DMA.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
iDMA 32-bit is Intel designed DMA controller that behaves like Synopsys
Designware DMA. This patch adds a support of the new Intel hardware.
Due to iDMA 32-bit has no autoconfiguration the platform code must
provide a platform data to dw_dma_probe().
By default full FIFO (1024 bytes) is assigned to channel 0. Here we
slice FIFO on equal parts between channels for iDMA 32-bit case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The integrated DMA (iDMA 32-bit) is Intel designed DMA controller which
mimics Synopsys Designware DMA. This patch appends the register mappings
for the parts which are slightly different to the DesignWare hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The newly introduced helpers prepare driver to support new DMA controller
hardware.
While here, introduce DWC_CTLH_BLOCK_TS() macro as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
iDMA 32-bit has a special handling of the FIFO during pause() /
terminate_all(). Prepare code to implement that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Replace convert_burst() with one liner in place.
The change simplifies further extension of the driver to cover new DMA
controller hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is really useful not only for debugging to have an IRQ line and DMA
pool labeled with driver and its instance ID. Do this for DesignWare DMA
driver.
All current users of this IP would be enhanced later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When transferring more data than the maximum block size supported by the
HW multiplied by source width the transfer is split into smaller chunks.
Currently code calculates the memory width and thus aligment before
splitting for both memory to device and device to memory transfers.
For memory to device transfers this work fine since alignment is preserved
through the splitting and split blocks are still memory width aligned.
However in device to memory transfers aligment breaks when maximum block
size multiplied by register width doesn't have the same alignment than the
buffer. For instance when transferring from an 8-bit register 4100 bytes
(32-bit aligned) on a DW DMA that has maximum block size of 4095 elements.
An attempt to do such transfers caused data corruption.
Fix this by calculating and setting the destination memory width after
splitting by using the split block aligment and length.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With patches "dmaengine: cppi41: Fix runtime PM timeouts with USB mass
storage", and "dmaengine: cppi41: Fix oops in cppi41_runtime_resume",
the pm_runtime_get/put() in cppi41_irq() is no longer needed. We now
guarantee that cppi41 is enabled when dma is in use.
We can still get pointless error -115 when musb is configured as a
usb peripheral. That's because we should now check for the state of
is_suspended instead.
Let's just remove the now useless code and replace it with a WARN().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
together with recent MUSB changes allowed USB and DMA on BeagleBone to idle
when no cable is connected. But looks like few corner case issues still
remain.
Looks like just by re-plugging USB cable about ten or so times on BeagleBone
when configured in USB peripheral mode we can get warnings and eventually
trigger an oops in cppi41 DMA:
WARNING: CPU: 0 PID: 14 at drivers/dma/cppi41.c:1154 cppi41_runtime_suspend+
x28/0x38 [cppi41]
...
WARNING: CPU: 0 PID: 14 at drivers/dma/cppi41.c:452
push_desc_queue+0x94/0x9c [cppi41]
...
Unable to handle kernel NULL pointer dereference at virtual
address 00000104
pgd = c0004000
[00000104] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
...
[<bf0d92cc>] (cppi41_runtime_resume [cppi41]) from [<c0589838>]
(__rpm_callback+0xc0/0x214)
[<c0589838>] (__rpm_callback) from [<c05899ac>] (rpm_callback+0x20/0x80)
[<c05899ac>] (rpm_callback) from [<c0589460>] (rpm_resume+0x504/0x78c)
[<c0589460>] (rpm_resume) from [<c058a1a0>] (pm_runtime_work+0x60/0xa8)
[<c058a1a0>] (pm_runtime_work) from [<c0156120>] (process_one_work+0x2b4/0x808)
This is because of a race with runtime PM and cppi41_dma_issue_pending()
as reported by Alexandre Bailon <abailon@baylibre.com> in earlier
set of patches. Based on mailing list discussions we however came to the
conclusion that a different fix from Alexandre's fix is needed in order
to guarantee that DMA is really active when we try to use it.
To fix the issue, we need to add a driver specific flag as we otherwise
can have -EINPROGRESS state set by runtime PM and can't rely on
pm_runtime_active() to tell us when we can use the DMA.
And we need to make sure the DMA transfers get triggered in the queued
order. So let's always queue the transfers, then flush the queue
from both cppi41_dma_issue_pending() and cppi41_runtime_resume()
as suggested by Grygorii Strashko <grygorii.strashko@ti.com> in an
earlier example patch.
For reference, this is also documented in Documentation/power/runtime_pm.txt
in the example at the end of the file as pointed out by Grygorii Strashko
<grygorii.strashko@ti.com>.
Based on earlier patches from Alexandre Bailon <abailon@baylibre.com>
and Grygorii Strashko <grygorii.strashko@ti.com> modified based on
testing and what was discussed on the mailing lists.
Fixes: fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bin Liu <b-liu@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
added runtime PM support for cppi41, but had corner case issues. Some of
the issues were fixed with commit 098de42ad6 ("dmaengine: cppi41: Fix
unpaired pm runtime when only a USB hub is connected"). That fix however
caused a new regression where we can get error -115 messages with USB on
BeagleBone when connecting a USB mass storage device to a hub.
This is because when connecting a USB mass storage device to a hub, the
initial DMA transfers can take over 200ms to complete and cppi41
autosuspend delay times out.
To fix the issue, we want to implement refcounting for chan_busy array
that contains the active dma transfers. Increasing the autosuspend delay
won't help as that the delay could be potentially seconds, and it's best
to let the USB subsystem to deal with the timeouts on errors.
The earlier attempt for runtime PM was buggy as the pm_runtime_get/put()
calls could get unpaired easily as they did not follow the state of
the chan_busy array as described in commit 098de42ad6 ("dmaengine:
cppi41: Fix unpaired pm runtime when only a USB hub is connected".
Let's fix the issue by adding pm_runtime_get() to where a new transfer
is added to the chan_busy array, and calls to pm_runtime_put() where
chan_busy array entry is cleared. This prevents any autosuspend timeouts
from happening while dma transfers are active.
Fixes: 098de42ad6 ("dmaengine: cppi41: Fix unpaired pm runtime when
only a USB hub is connected")
Fixes: fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bin Liu <b-liu@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The PL330 is hard-wired such that instruction fetches on both the
manager and channel threads go out onto the bus with the "privileged"
bit set. This can become troublesome once there is an IOMMU or other
form of memory protection downstream, since those will typically be
programmed by the DMA mapping subsystem in the expectation of normal
unprivileged transactions (such as the PL330 channel threads' own data
accesses as currently configured by this driver).
To avoid the case of, say, an IOMMU blocking an unexpected privileged
transaction with a permission fault, use the newly-introduced
DMA_ATTR_PRIVILEGED attribute for the mapping of our microcode buffer.
That way the DMA layer can do whatever it needs to do to make things
continue to work as expected on more complex systems.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mitchel Humpherys <mitchelh@codeaurora.org>
[rm: remove now-redundant local variable, clarify commit message]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Starting from Tangier B0 and continuing on Anniedale the HSU DMA interrupt
line is actually shared with UART. Handling them independently is racy and
quite often comes with the following traceback.
irq 54: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.0-rc6-edison64-86244934+ #1
Hardware name: Intel Corporation Merrifield/BODEGA BAY, BIOS 542 2015.01.21:18.19.48
ffff88003f203eb0 ffffffff8130e718 ffff880032627000 ffff88003262709c
ffff88003f203ed8 ffffffff810a3960 ffff880032627000 0000000000000000
ffff880032627000 ffff88003f203f10 ffffffff810a3cc7 ffff880032627000
Call Trace:
<IRQ>
[<ffffffff8130e718>] dump_stack+0x4d/0x65
[<ffffffff810a3960>] __report_bad_irq+0x30/0xc0
[<ffffffff810a3cc7>] note_interrupt+0x227/0x270
[<ffffffff810a1380>] handle_irq_event_percpu+0x40/0x50
[<ffffffff810a13b7>] handle_irq_event+0x27/0x50
[<ffffffff810a42d5>] handle_fasteoi_irq+0x85/0x150
[<ffffffff8101d7fe>] handle_irq+0x6e/0x120
[<ffffffff8105b8bc>] ? _local_bh_enable+0x1c/0x50
[<ffffffff8101d0d6>] do_IRQ+0x46/0xd0
[<ffffffff818cef3f>] common_interrupt+0x7f/0x7f
<EOI>
[<ffffffff818cdead>] ? mwait_idle+0x7d/0x140
[<ffffffff81024c9a>] arch_cpu_idle+0xa/0x10
[<ffffffff818ce150>] default_idle_call+0x20/0x30
[<ffffffff810908fd>] cpu_startup_entry+0x16d/0x1d0
[<ffffffff818c882d>] rest_init+0x6d/0x70
[<ffffffff81f93e8f>] start_kernel+0x3e2/0x3ef
[<ffffffff81f9343d>] x86_64_start_reservations+0x38/0x3a
[<ffffffff81f93529>] x86_64_start_kernel+0xea/0xed
handlers:
[<ffffffff81411670>] serial8250_interrupt
Disabling IRQ #54
Fix this by handling interrupt only in one place.
The issue is discussed here: https://github.com/andy-shev/linux/issues/5
Moreover this also fixes another bug when Rx DMA returns wrong residue and we
can't rely on it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ste_dma40 has burst level granularity on the residue
registers, which is necessary for some clients to know,
notably the UART. Before this patch we get this message:
uart-pl011 80007000.uart: RX DMA disabled - no residue processing
This patch fixes it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the introduction of the .directions flags, ste_dma40 was
never patched to indicate which transfer directions it can manage.
This causes a problem when trying to use the dmaengine for generic
ALSA SoC DMA:
ux500-msp-i2s.1: Failed to get DMA channel capabilities, falling
back to period counting: -6
This patch fixes this issue by indicating the supported transfer
directions for slave and memcpy channels.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The slave mapping should be removed together with other channel
resources when the channel is freed. If it's not unmapped it will hang
around forever after the channel is freed.
Fixes: 9f878603db ("dmaengine: rcar-dmac: add iommu support for slave transfers")
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We do not yet have users of port_window. The following errors were found
when converting the tusb6010_omap.c musb driver:
- The peripheral side must have SRC_/DST_PACKED disabled
- when configuring the burst for the peripheral side the memory side
configuration were overwritten: d->csdp = ... -> d->csdp |= ...
- The EI and FI were configured for the wrong sides of the transfers.
With these changes and the converted tus6010_omap.c I was able to verify
that things are working as they expected to work.
Fixes: 201ac4861c ("dmaengine: omap-dma: Support for slave devices with data port window")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds some error messages when a slave device fails to request a
channel.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On a kernel with DEBUG_LOCKS, ioat_free_chan_resources triggers an
in_interrupt() warning. With PROVE_LOCKING, it reports detecting a
SOFTIRQ-safe to SOFTIRQ-unsafe lock ordering in the same code path.
This is because dma_generic_alloc_coherent() checks if the GFP flags
permit blocking. It allocates from different subsystems if blocking is
permitted. The free path knows how to return the memory to the correct
allocator. If GFP_KERNEL is specified then the alloc and free end up
going through cma_alloc(), which uses mutexes.
Given that ioat_free_chan_resources() can be called in interrupt
context, ioat_alloc_chan_resources() must specify GFP_NOWAIT so that the
allocations do not block and instead use an allocator that uses
spinlocks.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
LPE Audio driver should take care of DMA IPs by itself. Keeping an ID like this
in dw_dma_pci.c is anyway wrong since that block has two DMA controllers under
one ID (like MFD device).
That's also why I didn't include LPE Audio ID for Intel Merrifield previously.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch sets the max_burst value supported by the STM32 DMA
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Implement the new device_synchronize() callback to allow proper
synchronization when stopping a channel.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch resolves the residue computation issue detected in cyclic mode.
Now, in cyclic mode, we increment next_sg variable as soon as a period is
transferred instead of after pushing a new sg request.
Then, we take into account that after transferring a complete buffer,
the next_sg variable is equal to 0.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch reworks the way to manage transfer starting.
Now, starting DMA is only allowed when the channel is not busy.
Then, stm32_dma_start_transfer is declared as void.
At least, after each transfer completion, we start the next transfer if a
new descriptor as been queued in the issued list during an ongoing
transfer.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As STM32 DMA driver is only used as buit-in driver, it couldn't be used as
module.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
PL330 DMA engine driver is leaking a runtime reference after any terminated
DMA transactions. This patch fixes this issue by tracking runtime PM state
of the device and making additional call to pm_runtime_put() in terminate_all
callback if needed.
Fixes: ae43b32891 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The original patch did not done what it was supposed to be doing and even
worst it broke legacy boot (OMAP1).
The lch_map size should be the number of available logical channels in sDMA
and the od->dma_requests should store the number of available DMA request
lines usable in sDMA.
In legacy mode we do not have a way to get the DMA request count, in that
case we use OMAP_SDMA_REQUESTS (127), despite the fact that OMAP1510 have
only 31 DMA request line.
Fixes: 2d1a9a946f ("dmaengine: omap-dma: Dynamically allocate memory for lch_map")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org # v4.9
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dma residue is defined as the free space to end of transfer buffer,
which could be multiple segments chained together. So the residue
calculation in zx_dma_tx_status() works for both slave_sg and cyclic
case. But unfortunately, the 'index' is wrong. It should plus one,
because the current segment is already occupied and shouldn't be counted
into free space.
This fixes the HDMI audio noise issue we see on ZX296718 with SPDIF
interface.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The zx_dma driver supports cyclic transfer mode. Let's set DMA_CYCLIC
cap_mask bit to make that clear, and avoid unnecessary failure when
clients request channel via dma_request_chan_by_mask() with DMA_CYCLIC
bit set in mask.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ZTE ZX dma driver is not ZX296702 specific. It works for not only
ZX296702 but also other ZTE ZX family platforms like ZX296718. Let's
rename the file to reflect that.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 3d8cc00073 ("dmaengine: ipu: Consolidate duplicated irq handlers")
consolidated the two interrupts routines into one, but the remaining
interrupt routine only checks the status of the error interrupts, not the
normal interrupts.
This patch fixes that problem (tested on i.MX31 PDK board).
Fixes: 3d8cc00073 ("dmaengine: ipu: Consolidate duplicated irq handlers")
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org> # 4.1.x
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine currently uses an IDR to allocate DMA IDs, but it only needs
to know whether IDs are in use or not; the ID to pointer functionality
of the IDR is unused. That means it can use the more space-efficient IDA.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chan->desc is always set to NULL when a DMA transfer is complete.
As a DMA transfer could be complete during the call of stm32_dma_tx_status,
we need to be sure that chan->desc is not NULL before using this variable
to avoid a null pointer deference issue.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch sets the right number of arguments to be used for DMA clients
which request channels from DT.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Skylake ioatdma is technically CBDMA 3.2+ and contains the same hardware
bits with some additional 3.3 features, but it's not really 3.3 where the
driver is concerned.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Adding Skylake Xeon PCI device ids for ioatdma and related bits.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Fairly routine update this time around with all changes specific to drivers.
o New driver for STMicroelectronics FDMA
o Memory-to-memory transfers on dw dmac
o Support for slave maps on pl08x devices
o Bunch of driver fixes to use dma_pool_zalloc
o Bunch of compile and warning fixes spread across drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pf0d
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"Fairly routine update this time around with all changes specific to
drivers:
- New driver for STMicroelectronics FDMA
- Memory-to-memory transfers on dw dmac
- Support for slave maps on pl08x devices
- Bunch of driver fixes to use dma_pool_zalloc
- Bunch of compile and warning fixes spread across drivers"
[ The ST FDMA driver already came in earlier through the remoteproc tree ]
* tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: sirf-dma: remove unused ‘sdesc’
dmaengine: pl330: remove unused ‘regs’
dmaengine: s3c24xx: remove unused ‘cdata’
dmaengine: stm32-dma: remove unused ‘src_addr’
dmaengine: stm32-dma: remove unused ‘dst_addr’
dmaengine: stm32-dma: remove unused ‘sfcr’
dmaengine: pch_dma: remove unused ‘cookie’
dmaengine: mic_x100_dma: remove unused ‘data’
dmaengine: img-mdc: remove unused ‘prev_phys’
dmaengine: usb-dmac: remove unused ‘uchan’
dmaengine: ioat: remove unused ‘res’
dmaengine: ioat: remove unused ‘ioat_dma’
dmaengine: ioat: remove unused ‘is_raid_device’
dmaengine: pl330: do not generate unaligned access
dmaengine: k3dma: move to dma_pool_zalloc
dmaengine: at_hdmac: move to dma_pool_zalloc
dmaengine: at_xdmac: don't restore unsaved status
dmaengine: ioat: set error code on failures
dmaengine: ioat: set error code on failures
dmaengine: DW DMAC: add multi-block property to device tree
...
Introduces remoteproc "subdevice" support, which allows remoteproc
driver to associate devices to the "running" state of the remoteproc,
allowing devices to be probed and removed as the remote processor is
booted, shut down or recovering from a crash.
Handling of virtio device resources was improved, vring memory is now
allocated as part of other memory allocation. This ensures that all
vrings for all virtio devices are allocated before we boot the remote
processor.
The debugfs mechanism for starting and stopping remoteproc instances was
replaced with a sysfs interface, also providing a mechanism for
specifying firmware to use by the instance. This allows user space to
load and boot use case specific firmware on remote processors.
New drivers for the ST Slimcore and Qualcomm Hexagon DSP as well as
removal of the unused StE modem loader.
Finally support for crash recovery in the Qualcomm Wirelss subsystem
(used for WiFi/BT/FM on a number of platforms) and a number of bug fixes
and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/1kU
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.10' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
- introduce remoteproc "subdevice" support, which allows remoteproc
driver to associate devices to the "running" state of the remoteproc,
allowing devices to be probed and removed as the remote processor is
booted, shut down or recovering from a crash.
- handling of virtio device resources was improved, vring memory is now
allocated as part of other memory allocation. This ensures that all
vrings for all virtio devices are allocated before we boot the remote
processor.
- the debugfs mechanism for starting and stopping remoteproc instances
was replaced with a sysfs interface, also providing a mechanism for
specifying firmware to use by the instance. This allows user space to
load and boot use case specific firmware on remote processors.
- new drivers for the ST Slimcore and Qualcomm Hexagon DSP as well as
removal of the unused StE modem loader.
- finally support for crash recovery in the Qualcomm Wirelss subsystem
(used for WiFi/BT/FM on a number of platforms) and a number of bug
fixes and cleanups
* tag 'rproc-v4.10' of git://github.com/andersson/remoteproc: (49 commits)
remoteproc: qcom_adsp_pil: select qcom_scm
remoteproc: Drop wait in __rproc_boot()
remoteproc/ste: Delete unused driver
remoteproc: Remove "experimental" warning
remoteproc: qcom_adsp_pil: select qcom_scm
dt-binding: soc: qcom: smd: Add label property
remoteproc: qcom: mdt_loader: add include for sizes
remoteproc: Update last rproc_put users to rproc_free
remoteproc: qcom: adsp: Add missing MODULE_DEVICE_TABLE
remoteproc: wcnss-pil: add QCOM_SMD dependency
dmaengine: st_fdma: Revert: "Revert: Update st_fdma to 'depends on REMOTEPROC'"
remoteproc: Add support for xo clock
remoteproc: adsp-pil: fix recursive dependency
remoteproc: Introduce Qualcomm ADSP PIL
dt-binding: remoteproc: Introduce ADSP loader binding
remoteproc: qcom_wcnss: Fix circular module dependency
remoteproc: Merge table_ptr and cached_table pointers
remoteproc: Remove custom vdev handler list
remoteproc: Update max_notifyid as we allocate vrings
remoteproc: Decouple vdev resources and devices
...
Pull x86 idle updates from Ingo Molnar:
"There were two bigger changes in this development cycle:
- remove idle notifiers:
32 files changed, 74 insertions(+), 803 deletions(-)
These notifiers were of questionable value and the main usecase,
the i7300 driver, was essentially unmaintained and can be removed,
plus modern power management concepts don't need the callback - so
use this golden opportunity and get rid of this opaque and fragile
callback from a latency sensitive code path.
(Len Brown, Thomas Gleixner)
- improve the AMD Erratum 400 workaround that used high overhead MSR
polling in the idle loop (Borisla Petkov, Thomas Gleixner)"
* 'x86-idle-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove empty idle.h header
x86/amd: Simplify AMD E400 aware idle routine
x86/amd: Check for the C1E bug post ACPI subsystem init
x86/bugs: Separate AMD E400 erratum and C1E bug
x86/cpufeature: Provide helper to set bugs bits
x86/idle: Remove enter_idle(), exit_idle()
x86: Remove x86_test_and_clear_bit_percpu()
x86/idle: Remove is_idle flag
x86/idle: Remove idle_notifier
i7300_idle: Remove this driver
In sirfsoc_dma_pm_suspend(), variable ‘sdesc’ is initialized but never used, which
leads to warning with W=1.
drivers/dma/sirf-dma.c: In function 'sirfsoc_dma_pm_suspend':
drivers/dma/sirf-dma.c:1014:27: warning: variable 'sdesc' set but not used [-Wunused-but-set-variable]
So remove it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In pl330_add(), variable ‘regs’ is initialized but never used, which
leads to warning with W=1.
drivers/dma/pl330.c: In function 'pl330_add':
drivers/dma/pl330.c:1891:16: warning: variable 'regs' set but not used [-Wunused-but-set-variable]
So remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In s3c24xx_dma_get_phy(), variable ‘cdata’ is initialized but never used, which
leads to warning with W=1. Removing this make pdata unused.
drivers/dma/s3c24xx-dma.c: In function ‘s3c24xx_dma_get_phy’:
drivers/dma/s3c24xx-dma.c:293:30: warning: variable ‘cdata’ set but not used [-Wunused-but-set-variable]
struct s3c24xx_dma_channel *cdata;
So remove both of them.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In stm32_dma_set_xfer_param(), variable ‘src_addr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_set_xfer_param’:
drivers/dma/stm32-dma.c:577:13: warning: variable ‘src_addr’ set but not used [-Wunused-but-set-variable]
dma_addr_t src_addr, dst_addr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In stm32_dma_set_xfer_param(), variable ‘dst_addr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_set_xfer_param’:
drivers/dma/stm32-dma.c:577:23: warning: variable ‘dst_addr’ set but not used [-Wunused-but-set-variable]
dma_addr_t src_addr, dst_addr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In stm32_dma_chan_irq(), variable ‘sfcr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_chan_irq’:
drivers/dma/stm32-dma.c:530:19: warning: variable ‘sfcr’ set but not used [-Wunused-but-set-variable]
u32 status, scr, sfcr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In pd_tx_submit(), variable ‘cookie’ is initialized but never used, which
leads to warning with W=1
drivers/dma/pch_dma.c: In function ‘pd_tx_submit’:
drivers/dma/pch_dma.c:420:15: warning: variable ‘cookie’ set but not used [-Wunused-but-set-variable]
dma_cookie_t cookie;
So remove it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In mic_dma_init(), variable ‘data’ is initialized but never used, which
leads to warning with W=1
drivers/dma/mic_x100_dma.c: In function ‘mic_dma_init’:
drivers/dma/mic_x100_dma.c:557:17: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
unsigned long data;
So remove it.
Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In mdc_prep_dma_memcpy(), mdc_prep_dma_cyclic() and mdc_prep_slave_sg()
variable ‘prev_phys’ is initialized but never used, which
leads to warning with W=1
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_dma_memcpy’:
drivers/dma/img-mdc-dma.c:295:24: warning: variable ‘prev_phys’ set but not used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_dma_cyclic’:
drivers/dma/img-mdc-dma.c:378:24: warning: variable ‘prev_phys’ set but not used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_slave_sg’:
drivers/dma/img-mdc-dma.c:461:24: warning: variable ‘prev_phys’ set but not
used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
So remove it.
Cc: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In usb_dmac_of_xlate(), variable ‘uchan’ is initialized but never used, which
leads to warning with W=1
drivers/dma/sh/usb-dmac.c: In function ‘usb_dmac_of_xlate’:
drivers/dma/sh/usb-dmac.c:655:24: warning: variable ‘uchan’ set but not used [-Wunused-but-set-variable]
struct usb_dmac_chan *uchan;
So remove it.
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In __cleanup(), variable ‘res’ is initialized but never used, which
leads to warning with W=1
drivers/dma/ioat/dma.c: In function ‘__cleanup’:
drivers/dma/ioat/dma.c:614:28: warning: variable ‘res’ set but not used [-Wunused-but-set-variable]
struct dmaengine_result res;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In ioat_tx_submit_unlock(), variable ‘ioat_dma’ is initialized but never
used, which leads to warning with W=1
drivers/dma/ioat/dma.c: In function ‘ioat_alloc_ring_ent’:
drivers/dma/ioat/dma.c:341:25: warning: variable ‘ioat_dma’ set but not used [-Wunused-but-set-variable]
struct ioatdma_device *ioat_dma;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In ioat3_dma_probe(), variable ‘is_raid_device’ is initialized but never
used, which leads to warning with W=1
drivers/dma/ioat/init.c: In function ‘ioat3_dma_probe’:
drivers/dma/ioat/init.c:1084:7: warning: variable ‘is_raid_device’ set
but not used [-Wunused-but-set-variable]
bool is_raid_device = false;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
save_gs is supposed to save the channel status in order to be restored at
resume time but it is never updated and is always 0. Anyway, the channel
status is updated in the per channel loop later in the resume function.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In function ioat_xor_val_self_test(), when the calls to
dma_mapping_error() fail, the value of return variable err is 0
(indicates no error). As a result, the return value may be inconsistent
with the execution status. This patch fixes the bug by assigning
"-ENOMEM" to err on the error path.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188601
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In function ioat_dma_self_test(), when the calls to dma_mapping_error()
fails, the value of return variable err is 0 (indicates no error). As a
result, the return value may be inconsistent with the execution status.
This patch fixes the bug by assigning -ENOMEM to err on the error path.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188591
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All known devices, which use DT for configuration, support
memory-to-memory transfers. So enable it by default, if we read
configuration from DT.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The last param set in a transfer should always be pointing to dummy
param set in non-cyclic mode. When system wakes from low power state
EDMA PARAM slots may be reset to random values. Hence, re-initialize
dummy slot to dummy param set on system resume.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Based on the src/dst_port_window_size - if it is set - configure the DMA
channel to use double indexing in order to be able to loop within the
address window.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We should use dma_pool_zalloc instead of dma_pool_alloc/memset.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We should use dma_pool_zalloc instead of dma_pool_alloc/memset.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Existing implementation does not honor the alignment restrictions imposed
by the DMA engines. Allocate buffers with built in slack for honoring
alignment restrictions. Creating new arrays to hold the aligned pointers
and use those pointers for operations.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Inside pdc_alloc_desc(), pci_pool_alloc() followed by memset will be
replaced by pci_pool_zalloc()
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_pool_alloc does not initialize the value of the newly allocated
block for the v_lli, and the uninitilize value make the tests failed
which is on pine64 with dmatest.
we can fix it just change the "|=" to "=" for the v_lli->cfg.
Signed-off-by: Hao Zhang <hao5781286@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is new API in place which provides allocation mechanism of interrupts for
PCI devices. Use it in the HSU DMA driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The residue calculation was taking in consideration that dma
transaction status will be always retrieved in the dma callback
used to inform that dma transfer is complete. However this is not
the case for all subsystems that use dma. Some subsystems use a
timer to check the dma status periodically.
Therefore the calculation was updated and residue is calculated
accordingly by a) update the residue calculation taking in
consideration the last used buffer index by using *buf_ptail* variable
and b) chn_real_count (number of bytes transferred) is initialized to
zero, when dma channel is created, to avoid using an uninitialized
value in residue calculation when dma status is checked without
waiting dma complete event.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
MODULE_DEVICE_TABLE is used by the kernel to determine which device driver
should be loaded for which platform device. MODULE_DEVICE_TABLE has been
only defined for the device-tree based platforms in the current code.
Defining it also for ACPI based platforms.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In preparation for removing the idle_notifier, remove its only user, the
i7300_idle driver.
i7300_idle was deployed in 2008 to reduce idle memory power on systems
using the i7300 chipset. The driver worked by throttling the
fully-buffered DIMMs during idle periods using the IOAT DMA engine.
The driver ran only on the i7300 chip-set, and no other hardware has used
this mechanism. The driver no longer has a maintainer.
Removing this driver will increase idle power on i7300 systems when they
run the new kernel without the driver.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/ad6a044e57cc75f44cc8621abe846e58f7882243.1479449716.git.len.brown@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix use of u32 instead of int for checking for negative errors values
as pointed out by Dan Carpenter <dan.carpenter@oracle.com>.
And while testing the PM runtime error path by randomly returning
failed values in runtime resume, I noticed two more places that need
fixing:
- If pm_runtime_get_sync() fails in probe, we still need to do
pm_runtime_put_sync() to keep the use count happy. We could call
pm_runtime_put_noidle() on the error path, but we're just going
to call pm_runtime_disable() after that so pm_runtime_put_sync()
will do what we want
- We should print an error if pm_runtime_get_sync() fails in
cppi41_dma_alloc_chan_resources() so we know where it happens
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 740b4be3f7 ("dmaengine: cpp41: Fix handling of error path")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the new channel request API introduced
in commit a8135d0d79
"dmaengine: core: Introduce new, universal API to request a channel".
param field of struct dma_slave_map type entries in the platform
data structure should be pointing to struct pl08x_channel_data
of related DMA channel.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts commit 6d066389d5 "(dmaengine:
st_fdma: Revert: Update st_fdma to 'depends on REMOTEPROC')" as the commit
it reverted was fine.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The 4.8-rc8 kernel is printing duplicate file entry warnings while removing
the HIDMA object. This is caused by stale sysfs entries remaining from the
previous execution.
_sysfs_warn_dup+0x5c/0x78
sysfs_add_file_mode_ns+0x13c/0x1c0
sysfs_create_file_ns+0x2c/0x40
device_create_file+0x54/0xa0
hidma_probe+0x7c8/0x808
Create hidma_sysfs_init and hidma_sysfs_uninit functions and call them from
the probe and remove path. To do proper clean up, adding the attrs object
to the device data structure to keep it around until remove call is made.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If we return early on pm_runtime_get() error, we need to also call
pm_runtime_put_noidle() as pointed out in a musb related thread
by Johan Hovold <johan@kernel.org>. This is to keep the PM runtime
use counts happy.
Fixes: fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The error for DMA Transfer Source Address Error was missing.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On am335x with musb host we can end up with unpaired pm runtime calls
if a hub with no devices is connected and disconnected.
This is because of the conditional pm runtime calls which are always
a bad idea. Let's fix the issue by making them unconditional and
paired in each function.
Fixes: fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If musb controller is configured with USB peripherals and we have
enumerated with a USB host, we can get warnings on removal of the
modules:
WARNING: CPU: 0 PID: 1269 at drivers/dma/cppi41.c:391
cppi41_dma_free_chan_resources
Fix the issue by adding the missing pm_runtime_get to
cppi41_dma_free_chan_resources to make sure the pending work
list is cleared on removal.
Fixes: fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The newly added MSI support causes a harmless warning when MSI
is disabled:
drivers/dma/qcom/hidma.c:558:20: error: 'hidma_chirq_handler_msi' defined but not used [-Werror=unused-function]
This adds another #ifdef to match that around the users of the function.
Fixes: 1c0e3e82a7 ("dmaengine: qcom_hidma: add MSI support for interrupts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts commit 184e13969f ("dmaengine:
st_fdma: Update st_fdma to 'depends on REMOTEPROC'") due to objection from
Bjorn.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_pool_alloc does not initialize the value of the newly allocated
block for the v_lli, and the uninitilize value make the tests failed
which is on pine64 with dmatest.
we can fix it just change the "|=" to "=" for the v_lli->cfg.
Signed-off-by: Hao Zhang <hao5781286@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After executing DMAGO it's possible that a request can come in for the
current xferred count, but if that happens too soon then DMAMOV SAR/DAR
may not have yet completed. If that happens, we should explicitly return 0
since nothing has been transferred yet.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Due to a hardware bug, reading memory (from the Accelerator Coherency Port)
with a burst size equal to the maximum burst size allowed by the DMA
hardware's buffer size will cause a hardware hang on the ARTPEC-6 SoC,
where the only solution is a manual power cycle.
On ARTPEC-6, this hardware bug does not trigger when writing memory (to the
Accelerator Coherency Port) with a burst size equal to the maximum burst
size allowed by the DMA hardware's buffer size.
To avoid this hardware hang, introduce a new optional max-burst property
for memory reads. For completeness, also introduce a max-burst property for
memory writes.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver currently uses modular infrastructure but is controlled
by a bool Kconfig.
There is a general consensus from the DMA reviewers and maintainers
that "if it can be modular, it should be modular" in order to keep
the bzImage size under control for multi platform kernels.
Build tested only. Also needed some new pm_clk symbols exported
before this commit is applied to tree in order to avoid modpost
errors like:
ERROR: "pm_clk_add_clk" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_create" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_destroy" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_suspend" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_resume" [drivers/dma/tegra210-adma.ko] undefined!
These were added as exports in the v4.8-rc1 merge window.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: dmaengine@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Device node iterators put the previous value of the index variable, so an
explicit put causes a double put.
Generated by: scripts/coccinelle/iterators/device_node_continue.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/dma/fsl_raid.ko | grep alias
$
After this patch:
$ modinfo drivers/dma/fsl_raid.ko | grep alias
alias: of:N*T*Cfsl,raideng-v1.0C*
alias: of:N*T*Cfsl,raideng-v1.0
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The interrupts can now be delivered as platform MSI interrupts on newer
platforms. The code looks for a new OF and ACPI strings in order to enable
the functionality.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When MSI interrupts are supported, error and the transfer interrupt can
come from multiple processor contexts.
Each error interrupt is an MSI interrupt. If the channel is disabled by
the first error interrupt, the remaining error interrupts will gracefully
return in the interrupt handler.
If an error is observed while servicing the completions in success case,
the posting of the completions will be aborted as soon as channel disabled
state is observed. The error interrupt handler will take it from there and
finish the remaining completions. We don't want to create multiple success
and error messages to be delivered to the client in mixed order.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Bring out the interrupt cause to the top level so that MSI interrupts
can be hooked at a later stage.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Getting ready for the MSI interrupts. The pending_tre_count is used
in the interrupt handler to make sure all outstanding requests are
serviced.
The driver will allocate 11 MSI interrupts. Each MSI interrupt can be
assigned to a different CPU. Then, we have a race condition for common
variables as they share the same interrupt handler with a different
cause bit and they can potentially be executed in parallel. Making this
variable atomic so that it can be updated from multiple processor
contexts.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During randconfig builds you can get the following warning
"warning: (ST_FDMA) selects ST_SLIM_REMOTEPROC which has unmet direct
dependencies (REMOTEPROC)"
randconfig builds should always build without any warnings so
update fdma to depend on REMOTEPROC so this can not happen.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case of error, the function st_slim_rproc_alloc() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Just iterate over the number of elements in array chanerr_str rather
than for all 32 bits. This removes the need for a NULL chanerr_str[i]
check which could possibly overrun if the upper bits (28..31) of
chanerr are set and 27th bit in chanerr is zero. This simplifies the
code by removing an if statement and a break.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We try to consume as much successful transfers as possible. Now that we
support MSI interrupts, an error interrupt might be observed by another
processor while we are finishing the successful ones.
Try to abort successful processing if this is the case.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Introducing the hidma_ll_setup_irq function to set up the interrupt
type externally from the OS interface.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Configure the DMA bindings for the device tree based firmware.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since 'commit acc29fb8f7 ("debugfs: ->d_parent is never NULL or
negative")', HIDMA object removal is no longer working. This is due to
redundant debugfs remove call in hidma_debug_uninit.
debugfs_remove_recursive(dmadev->debugfs);
debugfs_remove_recursive(dmadev->stats);
The first remove is for the directory. Second remove is for the file under
the directory. The directory remove makes file remove invalid.
Unable to handle kernel NULL pointer dereference at virtual address
[<ffff00000889f480>] down_write+0x18/0x68
[<ffff00000831c220>] debugfs_remove_recursive+0x50/0x1c0
[<ffff00000848e0a8>] hidma_debug_uninit+0x20/0x30
[<ffff00000848c5d8>] hidma_remove+0x48/0x98
[<ffff000008511b6c>] platform_drv_remove+0x24/0x68
[<ffff00000850fac8>] __device_release_driver+0x80/0x118
[<ffff00000850fb84>] device_release_driver+0x24/0x38
[<ffff00000850e928>] unbind_store+0xe8/0x110
[<ffff00000850dd30>] drv_attr_store+0x20/0x30
[<ffff000008253a48>] sysfs_kf_write+0x48/0x58
[<ffff000008252dd8>] kernfs_fop_write+0xb0/0x1d8
[<ffff0000081dab3c>] __vfs_write+0x1c/0x110
[<ffff0000081db940>] vfs_write+0xa0/0x1b8
[<ffff0000081dcd34>] SyS_write+0x44/0xa0
[<ffff000008082ef0>] el0_svc_naked+0x24/0x28
Removing the second line.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
can_pause is not initialized so it contains garbage. Fix this
by setting it to false.
Found using static analysis with cppcheck.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The newly added st_fdma driver introduces a build warning for
allmodconfig when we add '-Wmaybe-uninitialized':
drivers/dma/st_fdma.c: In function 'st_fdma_probe':
drivers/dma/st_fdma.c:777:5: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The warning is correct, though this can't happen in practice
as the check is redundant (we don't get to this function if
the pointer is NULL). Even if the function were called with a
NULL of_node, the check is not needed because of_property_read_u32
can deal with a NULL argument by returning an error.
Removing the unnecessary code simplifies the function and avoids
the condition that we get the warning for.
Fixes: 6b4cd727ea ("dmaengine: st_fdma: Add STMicroelectronics FDMA engine driver support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When an error is observed, we try to disable the channel and prevent
further accesses from the client.
Depending on the type of error, transitioning into disabled state might
not be possible. Adding a check to make sure that HW is in enabled/running
state before the disable transition happens.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are some compilation errors when CONFIG_MMP_TDMA is enabled and
CONFIG_GENERIC_ALLOCATOR is disabled:
drivers/built-in.o: In function `mmp_tdma_prep_dma_cyclic':
mmp_tdma.c:(.text+0x7890e): undefined reference to `gen_pool_dma_alloc'
drivers/built-in.o: In function `mmp_tdma_free_chan_resources':
mmp_tdma.c:(.text+0x78aca): undefined reference to `gen_pool_free'
drivers/built-in.o: In function `mmp_tdma_probe':
mmp_tdma.c:(.text+0x78ea8): undefined reference to `of_gen_pool_get'
This commit fix this problem by selecting GENERIC_ALLOCATOR when
CONFIG_MMP_TDMA is enabled.
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This DMA driver is used by 8250-omap on DRA7-evm. There is one
requirement that is to pause a transfer. This is currently used on the RX
side. It is possible that the UART HW aborted the RX (UART's RX-timeout)
but the DMA controller starts the transfer shortly after.
Before we can manually purge the FIFO we need to pause the transfer,
check how many bytes it already received and terminate the transfer
without it making any progress.
From testing on the TX side it seems that it is possible that we invoke
pause once the transfer has completed which is indicated by the missing
CCR_ENABLE bit but before the interrupt has been noticed. In that case the
interrupt will come even after disabling it.
The AM572x manual says that we have to wait for the CCR_RD_ACTIVE &
CCR_WR_ACTIVE bits to be gone before programming it again here is the
drain loop. Also it looks like without the drain the TX-transfer makes
sometimes progress.
One note: The pause + resume combo is broken because after resume the
the complete transfer will be programmed again. That means the already
transferred bytes (until the pause event) will be sent again. This is
currently not important for my UART user because it does only pause +
terminate.
v3…v4:
- update subject line.
v2…v3:
- rephrase the comment based on Russell's information / feedback.
v1…v2:
- move the drain loop into omap_dma_drain_chan() instead of having it
twice.
- allow pause only for DMA_DEV_TO_MEM transfers if non-cyclic. Add a
comment why DMA_MEM_TO_DEV not allowed.
- clear pause on terminate_all. Otherwise pause() + terminate_all()
will keep the pause bit set and we can't pause the following
transfer.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[vigneshr@ti.com: drain channel only when buffering is on, rebase to v4.8]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts commit c91134d919.
The conversion of the pxa architecture is now finished for all
drivers, so this functions has fullfilled its purpose and can
now be removed.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the Flexible Direct Memory Access (FDMA) core
driver. The FDMA is a slim core CPU with a dedicated firmware.
It is a general purpose DMA controller capable of supporting 16
independent DMA channels. Data moves maybe from memory to memory
or between memory and paced latency critical real time targets and it
is found on al STi based chipsets.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This header file will also be used by the dma xbar driver in the
future.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of dmaenegine to
register a callback_result which tells them the result of the dma
transaction. Right now only one user ntb is using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no place in
kernel, this also remove NO_IRQ from dmaengine subsystem (both arm and
ppc users)
- Support for IOMMU slave transfers and it implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of driver,
and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9iA3
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of
dmaenegine to register a callback_result which tells them the
result of the dma transaction. Right now only one user (ntb) is
using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no
place in kernel, this also remove NO_IRQ from dmaengine subsystem
(both arm and ppc users)
- Support for IOMMU slave transfers and its implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of
driver, and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers"
* tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (169 commits)
async_pq_val: fix DMA memory leak
dmaengine: virt-dma: move function declarations
dmaengine: omap-dma: Enable burst and data pack for SG
DT: dmaengine: rcar-dmac: document R8A7743/5 support
dmaengine: fsldma: Unmap region obtained by of_iomap
dmaengine: jz4780: fix resource leaks on error exit return
dma-debug: fix ia64 build, use PHYS_PFN
dmaengine: coh901318: fix integer overflow when shifting more than 32 places
dmaengine: edma: avoid uninitialized variable use
dma-mapping: fix m32r build warning
dma-mapping: fix ia64 build, use PHYS_PFN
dmaengine: ti-dma-crossbar: enable COMPILE_TEST
dmaengine: omap-dma: enable COMPILE_TEST
dmaengine: edma: enable COMPILE_TEST
dmaengine: ti-dma-crossbar: Fix of_device_id data parameter usage
dmaengine: ti-dma-crossbar: Correct type for of_find_property() third parameter
dmaengine/ARM: omap-dma: Fix the DMAengine compile test on non OMAP configs
dmaengine: edma: Rename set_bits and remove unused clear_bits helper
dmaengine: edma: Use correct type for of_find_property() third parameter
dmaengine: edma: Fix of_device_id data parameter usage (legacy vs TPCC)
...
We get 2 warnings when building kernel with W=1:
drivers/dma/virt-dma.c:22:14: warning: no previous prototype for 'vchan_tx_submit' [-Wmissing-prototypes]
drivers/dma/virt-dma.c:52:5: warning: no previous prototype for 'vchan_tx_desc_free' [-Wmissing-prototypes]
In fact, these two functions are incorrectly declared in a function.
So this patch moves function declarations out of this function.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Enable the burst and data pack modes for the scatter-gather
in order to improve the throughput of the data transfers.
The improvement has been verified with MMC HS200 mode in
the DRA72 EVM using the iozone tool to compare the read
throughput (in kB/s) with and without burst/pack for
different reclens (in kB).
With
reclen Baseline sDMA burst/pack
------ -------- ---------------
64 46568 50820
128 57564 63413
256 65634 74937
512 72427 83483
1024 74563 84504
2048 76265 86079
4096 78045 87335
8192 78989 88154
16384 81265 91034
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Free memory mapping, if probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
