Commit Graph

478 Commits

Author SHA1 Message Date
Don Skidmore
5da43c1a78 ixgbe: fix inconsistent SFP/SFP+ failure results.
Currently if we loaded the driver, insert an unsupported module, and then
attempt to "ifconfig up" the device it will be brought down but the netdev
would not be unregistered. This behavior is different than all other
code paths. This patch corrects that by down'ing the device and then
scheduling the sfp_config_module_task tasklet. The tasklet will detect
this condition (like it does with other code paths) and do the
unregister_netdev().

I also removed the log message as this condition (an unsupported SFP+
module) will be logged in sfp_config_module_task.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:11:05 -07:00
Don Skidmore
19343de279 ixgbe: fix regression on some 82598 adapters
The change to check the SFP+ module again on open() was
causing the XFP (non-SFP+) adapters to be rejected. We
only want to try and re-identify the SFP+ module if the
original probe found that this device was an SFP+ device.
So for this code path (driver loaded with SFP module, module
inserted, ifconfig up of the device) the type will be
ixgbe_phy_unknown for an unidentified SFP+ module.  So we
only check if that is the case.

This problem also shows up on Copper devices.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:11:00 -07:00
Don Skidmore
63d6e1d80a ixgbe: fix issues with failing to detect insert of unsupported module
Several small fixes around negative test case of the insertion of a
IXGBE_ERR_NOT_SUPPORTED module.

- mdio45_probe call was always failing due to mdio.prtad not being
set.  The function set to mdio.mdio_read was still working as we just
happen to always be at prtad == 0.  This will allow us to set the phy_id
and phy.type correctly now.

- There was timing issue with i2c calls when initiated from a tasklet.
A small delay was added to allow the electrical oscillation to calm down.

- Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition
to be recognized.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:55 -07:00
Jesse Brandeburg
4f57ca6e17 ixgbe: fix unmap length bug
This patch addresses three WARN_ON statements from DMA-API debug code

ixgbe is mapping more than it unmaps, reduce the length of the map call and
remove the "used once" local variable.

found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate
for -stable.

in addition, fix missing ->dma = 0 after unmap to prevent double free with
pci_unmap_single

and lastly, don't unmap (half) pages that aren't mapped.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:54 -07:00
Mallikarjuna R Chilakala
a1f25324b9 ixgbe: Fix link capabilities during adapter resets
Adapter link advertisement capabilities were not persistent during
adapter resets. While configuring multispeed fiber link check for
phy autoneg_advertised settings before overwriting with default
link capabilities

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:53 -07:00
Mallikarjuna R Chilakala
a380137900 ixgbe: Fix device capabilities of 82599 single speed fiber NICs.
82599 single speed fiber modules only support 10G/Full. Return
proper device capabilities while querrying the adapter and error
while changing device advertisement/speed/duplex capabilities.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:53 -07:00
Don Skidmore
88d2b81f4e ixgbe: Fix SFP log messages
We had a wide range of log messages for the same sort of SFP
failure.  This patch makes them all more similar and less
confusing along with converting them to dev_err.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:51 -07:00
Andrew Morton
8e20ce94ce convert some DMA_nnBIT_MASK() callers
We're about to make DMA_nnBIT_MASK() emit `deprecated' warnings.  Convert the
remaining stragglers which are visible to the x86_64 build.

Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsil.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Yi Zou <yi.zou@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19 16:46:06 -07:00
Jiri Pirko
31278e7147 net: group address list and its count
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
   on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>

 drivers/net/bnx2.c              |    4 +-
 drivers/net/e1000/e1000_main.c  |    4 +-
 drivers/net/ixgbe/ixgbe_main.c  |    6 +-
 drivers/net/mv643xx_eth.c       |    2 +-
 drivers/net/niu.c               |    4 +-
 drivers/net/virtio_net.c        |   10 ++--
 drivers/s390/net/qeth_l2_main.c |    2 +-
 include/linux/netdevice.h       |   17 +++--
 net/core/dev.c                  |  130 ++++++++++++++++++--------------------
 9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-18 00:29:08 -07:00
Yi Zou
3d8fd38567 ixgbe: Include offloaded FCoE data into total rx/tx statistics for 82599
Include offloaded FCoE data into total rx/tx statistics for 82599 so they
are properly reflected by ethtool or ifconfig.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-09 05:25:37 -07:00
Eric Dumazet
042a53a9e4 net: skb_shared_info optimization
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.

One to access nr_frags, one to access dma_maps[0]

Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.

Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08 00:21:48 -07:00
Peter P Waskiewicz Jr
a1c1db3920 ixgbe: Increase the driver version number
With all the last patchsets going in for 82599 feature enablement, the
driver version needs to be increased for better identification.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:26 -07:00
Peter P Waskiewicz Jr
794caeb259 ixgbe: Add FW detection and warning for 82599 SFP+ adapters
82599 has a FW running that helps manage the internal SFI PHY.  There are
also a number of pre-production samples of these SFI-based devices in the
field.  This patch adds a check to look for the firmware running on all
SFP+ based adapters, and displays a warning to the system log if a
pre-production adapter is identified.  The driver will continue loading
though, with no functional degradation.

Also remove an old function prototype from ixgbe_82599.c that isn't being
used.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:26 -07:00
Jesse Brandeburg
ae540af185 ixgbe: Re-adjust ring layouts to have better cacheline efficiency
This patch rearranges the ixgbe_ring struct to make better use of
cacheline efficiency.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:25 -07:00
Peter P Waskiewicz Jr
c4cf55e5d2 ixgbe: Enable Flow Director hashing in 82599
This patch enables Flow Director's ATR functionality to the main base
driver for 82599.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:24 -07:00
Peter P Waskiewicz Jr
ffff477203 ixgbe: Add Flow Director init and modify functions for 82599
This patch adds the functions for ixgbe to initialize Flow Director.  It
also has the function APIs to add Flow Director filters from the base
driver.  This also includes ATR, Application Targeted Routing, which is a
feature set of Flow Director.  This is the hash-based mechanism to
automatically identify flows and add filters based on the hash, and direct
the Rx of that flow back to that same CPU.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:24 -07:00
Peter P Waskiewicz Jr
bfde493ee2 ixgbe: Add hardware defines for Flow Director for 82599
Flow Director is a Rx filter mechanism designed to match Rx flows back to
the same CPU that the flow's Tx occurred from.  This patch adds the first
piece, the defines for the hardware registers, to enable this feature in
82599 hardware.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:23 -07:00
Peter P Waskiewicz Jr
df647b5ca3 ixgbe: Add a second feature flags variable, move HW RSC capability there
This adds a second feature flag variable to use for future feature
expansion.  Add HW RSC to this new feature flags variable.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:22 -07:00
Alexander Duyck
91281fd36c ixgbe: move tx processing into NAPI context
This patch moves the tx cleanup processing out of the MSI-X interrupt
processing and gives it it's own napi routine.  This allows the driver to
process TX cleanup in a polling context instead of in an interrupt context
which prevents TX from starving RX.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:21 -07:00
Alexander Duyck
fe49f04aa8 ixgbe: move v_idx into q_vector and use as index only
The v_idx value was being used as both a bitmask and an index.  This change
makes it so that the q_vector contains the index and allows for much of the
code to be simplified since disabling a q_vector involves only clearing one
bit in the interrupt bitmask.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:20 -07:00
Alexander Duyck
21fa4e66bd ixgbe: use rx_buffer_info->dma instead of nr_frags to determine skb unmap
This patch changes the driver so that it uses rx_buffer_info->dma to
determine if it needs to unmap the page instead of sh_info->nr_frags.  This
helps to prevent a cache line miss when receiving small packets as the
rx_buffer_info data should already be in the cache.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:20 -07:00
Mallikarjuna R Chilakala
74766013a1 ixgbe: ethtool support to change advertised link modes of 82599 adapters
Add ethtool support to change advertised link modes/autoneg settings of
82599 multispeed fiber adapters.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:19 -07:00
Mallikarjuna R Chilakala
620fa036b2 ixgbe: Fix 82599 adapter link flickering issues
Fix autoneg restart issues in flow control path which might create
endless link flickering due to known timing issues with 82599
adapters.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakakla@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:19 -07:00
Peter P Waskiewicz Jr
50ac58ba1d ixgbe: Harden the 82599 multispeed fiber autotry mechanism
82599 supports multispeed fiber optical modules (10Gbps/1Gbps).  Some
scenarios can cause the autotry mechanism to not negotiate link properly.
What needs to happen is the driver must flap the Tx laser to induce an Rx
Loss of Signal on the link partner.  This will restart the autotry
mechanism to get link into a known state.  The software definable pin (SDP)
3 on the 0x10fb NIC is wired to cause a Tx LOS event, which triggers the
Rx LOS we require.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:18 -07:00
Peter P Waskiewicz Jr
da4dd0f7ca ixgbe: Add ethtool offline test support
This patch adds support for the ethtool internal test engine.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:16 -07:00
Peter P Waskiewicz Jr
1479ad4fbf ixgbe: Change the 82599 PHY DSP restart logic
When reprogramming the 82599 analog PHY to either SFI optical or Direct
Attach Twinax, we need to restart the DSP in the PHY.  The current method
can cause contention with our FW which is managing PHY state, and will
cause unexpected link flaps.  This patch fixes the DSP restart by issuing
an AN_RESTART in the MAC, which will properly propagate the DSP restart to
the PHY.  This ensures we don't collide with the FW.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:16 -07:00
Peter P Waskiewicz Jr
bdf0a550c8 ixgbe: Enable ACPI WoL capabilities for 82599
The 82599 KX4 device defaults to legacy power management, or APME.  This
puts the device into ACPI mode, which allows more robust WoL setups to
work properly.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-07 05:20:15 -07:00
Jiri Pirko
ccffad25b5 net: convert unicast addr list
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).

I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.

The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>

 drivers/net/bnx2.c               |   13 +--
 drivers/net/e1000/e1000_main.c   |   24 +++--
 drivers/net/ixgbe/ixgbe_common.c |   14 ++--
 drivers/net/ixgbe/ixgbe_common.h |    4 +-
 drivers/net/ixgbe/ixgbe_main.c   |    6 +-
 drivers/net/ixgbe/ixgbe_type.h   |    4 +-
 drivers/net/macvlan.c            |   11 +-
 drivers/net/mv643xx_eth.c        |   11 +-
 drivers/net/niu.c                |    7 +-
 drivers/net/virtio_net.c         |    7 +-
 drivers/s390/net/qeth_l2_main.c  |    6 +-
 drivers/scsi/fcoe/fcoe.c         |   16 ++--
 include/linux/netdevice.h        |   18 ++--
 net/8021q/vlan.c                 |    4 +-
 net/8021q/vlan_dev.c             |   10 +-
 net/core/dev.c                   |  195 +++++++++++++++++++++++++++-----------
 net/dsa/slave.c                  |   10 +-
 net/packet/af_packet.c           |    4 +-
 18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-29 22:12:32 -07:00
Eric Dumazet
28679751a9 net: dont update dev->trans_start in 10GB drivers
Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.

Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-29 01:46:26 -07:00
Peter P Waskiewicz Jr
0fb2787bf2 ixgbe: Fix build warning
This patch fixes a build warning due to an unused label.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-26 21:41:18 -07:00
Don Skidmore
8ca783ab78 ixgbe: fix 82598 SFP initialization after driver load.
If we loaded the driver with out a SFP module plugged in it would
leave it in a state that make it later unable to link when a module
was plugged in.  This patch corrects that by:

ixgbe_probe() - moving the check for IXGBE_ERR_SFP_NOT_PRESENT from
after get_invariants() to after reset_hw() as now reset_hw() is
where this condition will be indentified.

ixgbe_reset_hw_82598() - Enable this function to now return
IXGBE_ERR_SFP_NOT_PRESENT.

ixgbe_identify_sfp_module_generic() - This where the lack of SFP
module is detected.  Modifications are added to allow a different
return value for modules that just haven't been plugged in yet.

Other functions were updated to allow correct logging.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-26 20:40:47 -07:00
Peter P Waskiewicz Jr
f7c86a3252 ixgbe: Remove device ID 0x10d8
Device ID 0x10d8 is the default silicon device ID for 82599.  However, the
device will not be functional without an EEPROM, so we want to prevent the
driver from loading on the device.  Otherwise, the driver will load, but no
PHY setup or PCIe setup will occur, causing the device to be unusable.  To
prevent users from encountering this, just remove the device ID.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-26 20:40:09 -07:00
Alexander Duyck
e35ec12650 ixgbe: only register DCA requester once
The current driver tries to re-register the DCA requester after reset and
this is not correct.  This change makes it so all we are doing is resetting
the DCA registers after reset and not re-adding the requester.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-21 17:19:10 -07:00
Jesse Brandeburg
0cefafadbb ixgbe: Cleanup feature setup code to make the code more readable
This is purely a cleanup patch.  This collapses some of the code required
when we configure our Tx and Rx feature sets, and makes the code more
readable and maintainable.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 15:36:14 -07:00
Peter P Waskiewicz Jr
537d58a00a ixgbe: Change Direct Attach Twinax cable detection for SFP+ NICs
The SFF specification for Direct Attach cable detection has now been
ratified.  Previously, DA cable detect was looking at the Twinaxial bit in
byte 9 of the SFP+ EEPROM.  The spec now defines active and passive DA
cables in byte 8 of the SFP+ EEPROM.  This patch changes the cable
detection for both 82598 and 82599 SFP+ adapters to conform to the new
spec.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 15:36:14 -07:00
Peter P Waskiewicz Jr
aa5aec8885 ixgbe: Add semaphore access for PHY initialization for 82599
The SFP+ NIC (device id 0x10fb) needs a semaphore to serialize
PHY access, so our PHY init code must honor that same semaphore.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-19 15:36:13 -07:00
Peter P Waskiewicz Jr
ba98898eb3 ixgbe: Increase the driver version number
Marching along, let's bump the version number to indicate things actually
have happened to the driver.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-18 15:09:44 -07:00
Peter P Waskiewicz Jr
1fcf03e656 ixgbe: Add generic XAUI support to 82599
This patch adds the generic XAUI device support for 82599 controllers.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-18 15:09:44 -07:00
Alexander Duyck
e76678dd65 ixgbe: set max desc to prevent total RSC packet size of 64K
The performance of hardware RSC is greatly reduced if the total for max rsc
descriptors multiplied by the buffer size is greater than 65535.  To
prevent this we need to adjust the max rsc descriptors appropriately.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-18 15:09:43 -07:00
Peter P Waskiewicz Jr
62551d3ea0 ixgbe: Don't reset the hardware when switching between LFC and PFC
When running in DCB mode, switching between link flow control and priority
flow control shouldn't need to reset the hardware.  This removes that
reset.

This also extends the set_all() dcbnl callback to return a value indicating
that the HW config changed, however a reset was not required.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:04:14 -07:00
Peter P Waskiewicz Jr
8756924c1e ixgbe: When in DCB mode with PFC enabled, show LFC is disabled
Ethtool should report that link flow control is disabled when in priority
flow control mode.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:04:14 -07:00
Peter P Waskiewicz Jr
264857b8fe ixgbe: Allow link flow control in DCB mode for 82599 adapters
82599 supports using either link flow control or priority flow control when
in DCB mode.  The dcbnl interface already supports sending down
configurations through rtnetlink that can enable LFC when DCB is enabled,
so the driver should take advantage of this.

82598 does not support using LFC when DCB is enabled, so explicitly disable
it when we're in DCB mode.  This means we always run in PFC mode when DCB
is enabled.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:04:13 -07:00
Peter P Waskiewicz Jr
70b77628d8 ixgbe: Set Priority Flow Control low water threshhold for DCB
This sets the low water threshhold for priority flow control for 82598
and 82599 controllers in DCB mode.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:04:13 -07:00
Yi Zou
63f39bd17a ixgbe: Enable jumbo frame for FCoE feature in 82599
Enable jumbo frame when FCoE feature is enabled in 82599. Use 3K
as the receive queue buffer size for receive queues used by FCoE
to address for max Fiber Channel frame size as 2148 bytes (with
max 2112 bytes of payload).

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:04:10 -07:00
Yi Zou
29ebf6f8c8 ixgbe: Enable FCoE redirection table feature in 82599
Enable using FCoE redirection table feature in 82599. The FCoE
redirection table has maximum of eight entries, corresponding
to maximum of eight receive queues to be used for distributing
incoming FCoE packets. This patch sets up the FCoE redirection
table when multiple receive queues are available for FCoE.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:04:10 -07:00
Yi Zou
0331a832a8 ixgbe: Add RING_F_FCOE for FCoE feature in 82599
Add ring feature for FCoE to make use of the FCoE redirection
table in 82599. The FCoE redirection table is a receive side
scaling feature for Fiber Channel over Ethernet feature in 82599,
enabling distributing FCoE packets to different receive queues
based on the exchange id.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:04:09 -07:00
Waskiewicz Jr, Peter P
aca6bee75f ixgbe: Add SAN MAC address to the RAR, return the address to DCB
After acquiring the SAN MAC address from the EEPROM, we need to program it
into one of the RARs.  Also, DCB will use this MAC address to run DCBX
commands, so it doesn't have to play musical MAC addresses when things like
bonding enter the picture.  So we need to return the MAC address through
the netlink interface to userspace.

This also moves the init_rx_addrs() call out of start_hw() and into
reset_hw().  We shouldn't try to read any of the RAR information before
initializing our internal accounting of the RAR table, which was what
was happening.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:04:07 -07:00
PJ Waskiewicz
0365e6e437 ixgbe: Add FCoE Storage MAC Address support
This patch implements the Storage Address entrypoint from the net device.
It will read the SAN MAC addresses from the EEPROM of the 82599 hardware,
and make them available to the FCoE stack through the net device.

Also, add/del the SAN MAC address to the netdev dev_addr_list via the
kernel api dev_addr_add()/dev_addr_del() when there is a valid SAN MAC
supported by the HW.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:04:07 -07:00
Yi Zou
6d45522c53 ixgbe: Add FCoE related statistics to 82599
This adds FCoE related statistics to 82599, including number Rx-ed and Tx-ed
FCoE packets, number of Rx-ed and Tx-ed FCoE packets in dwords, number of bad
Fiber Channel CRCs detected in FCoE packets, and number of FCoE packets dropped
on the Rx side.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 12:00:09 -07:00
Yi Zou
332d4a7d98 ixgbe: Implement FCoE Rx side large receive offload feature to 82599
This patch implements the FCoE Rx side offload feature in ixgbe_main.c
to 82599 using the Rx offload infrastructure code added in the previous
patch. The large receive offload by Direct Data Placement (DDP) for
FCoE is achieved by implementing the ndo_fcoe_ddp_setup and ndo_fcoe_ddp_done
in net_device_ops via netdev. It is up to the ULD, i.e., fcoe and libfc
to query and setup large receive offload accordingly through the corresponding
netdev upon creating fcoe instances.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 12:00:08 -07:00
Yi Zou
d0ed89373f ixgbe: Add infrastructure code for FCoE large receive offload to 82599
This adds infrastructure code for FCoE Rx side offload feature to
82599, which provides large receive offload for FCoE by Direct
Data Placement (DDP). The ixgbe_fcoe_ddp_get() and ixgbe_fcoe_ddp_put()
pair corresponds to the netdev support to FCoE by the function pointers
provided in net_device_ops as ndo_fcoe_ddp_setup and ndo_fcoe_ddp_done.
The implementation of these in ixgbe is shown in the next patch.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 12:00:07 -07:00
Yi Zou
eacd73f79a ixgbe: Implement FCoE Tx side offload features in base driver of 82599
This patch implements the FCoE Tx side offload features in ixgbe_main.c
to 82599 using the Tx offload infrastructure code added in the previous
patch. This is achieved by the calling the FCoE Sequence Offload (FSO)
function ixgbe_fso() on the transmit path of ixgbe.

This patch also includes an EEPROM check to make sure the NIC we're loading
on is an offload-enabled SKU.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 12:00:04 -07:00
Yi Zou
bc079228e7 ixgbe: Add infrastructure code for FCoE large send offload to 82599
This adds infrastructure code for FCoE Tx side offload feature to
82599, including Fiber Channel CRC calculation, auto insertion of
the start of frame (SOF) and end of frame (EOF) of FCoE packets,
and large send by FCoE Sequence Offload (FSO).

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 12:00:03 -07:00
Yi Zou
d3a2ae6d31 ixgbe: Add FCoE feature code to 82599
This adds the FCoE feature code ixgbe_fcoe.c to 82599. For a start, this patch
only adds ixgbe_configure_fcoe() to configure related register for FCoE to 82599.
In patches that follow, I will be adding more functions to ixgbe_fcoe.c to add
support of FCoE offload features to 82599.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 12:00:02 -07:00
Yi Zou
e92cbeac89 ixgbe: Add FCoE feature header to 82599
This adds the FCoE feature header ixgbe_fcoe.h to 82599. This header includes
the defines and structures required by the ixgbe driver to support various
offload features in 82599 for Fiber Channel over Ethernet (FCoE).  These offloads
features include Fiber Channel CRC calculation, FCoE SOF/EOF auto insertion,
FCoE Sequence Offload (FSO) for large send, and Direct Data Placement (DDP)
for large receive.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 12:00:01 -07:00
Yi Zou
bff66176bb ixgbe: Add FCoE feature register defines to 82599
This adds FCoE related register defines to 82599.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 11:59:57 -07:00
Nelson, Shannon
c9c7d2e5a0 ixgbe: Typecase '1' for 64 bit shift
Make sure we don't get any sign-extend issues when we shift a 1
into bit 31.

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-07 14:52:32 -07:00
Don Skidmore
bf069c9726 ixgbe: fix failing to log fan failures
We weren't logging the 82598AT fan failure if it occurred before (ixgbe_open)
as we hadn't sent up to catch the interrupt that event caused.

This patch checks for this failure in:
ixgbe_probe - So we can log the failure asap. We check right after we
set up the adapter->flags, which is when we know that we have a fan.
ixgbe_up_complete - To catch failures that may have happened between probe
and when we set up the interrupt that would normally detect the fan failure.

To enable all of this we need to initialize the adapter flag with
IXGBE_FLAG_FAN_FAIL_CAPABLE when the NIC contained a fan.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-07 14:52:31 -07:00
Yi Zou
dfa12f05f6 ixgbe: Enable L2 header split in 82599
This enables L2 header split when packet split is enabled for 82599.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-07 14:52:30 -07:00
Alexander Duyck
163de42e24 ixgbe: set queue0 for srrctl configuration correctly for DCB
The current configuration is not setting queue 0 correctly for DCB
configurations.  As a result unconfigured queues are being used to setup
the SRRCTL register rx buffer len sizes.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-07 14:52:30 -07:00
Alexander Duyck
afafd5b020 ixgbe: always set header length in SRRCTL
As per the documentation for 82599 in order to support hardware RSC the
header size must be set.  This is only currently done for packet split
mode.  This patch sets the header buffer length for all modes.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-07 14:52:29 -07:00
gouji-new
9ce77666da ixgbe: Proposed PARCH PCIE legacy I/O port free intel 10Gb NIC driver
Traditionally Intel based NIC drivers request I/O port even though it
doesn't need that really.

Intel PCIE 10Gb driver (ixgbe) also requests I/O port but it doesn't
need it either.

This is a little inconvenient situation because sometimes we have to
handle those cards on the slots where any I/O space is not attached.

So we made pach which makes ixgbe driver legacy I/O port free.

Signed-off-by: Masayuki Gouji <gouji.masayuki@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-06 15:33:47 -07:00
Breno Leitao
3044b8d1ff ixgbe: Return PCI_ERS_RESULT_DISCONNECT when bus is disabled
According to the "PCI Error Recovery" document, if after a recovery,
the bus is disabled, the error_detected function should return
PCI_ERS_RESULT_DISCONNECT. Actually ixgbe error_detected function is
always returning PCI_ERS_RESULT_NEED_RESET, even if the bus is in failure.
This patch just check if the bus is disabled and then returns
PCI_ERS_RESULT_DISCONNET.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-06 15:33:47 -07:00
Alexander Duyck
2012bdc8a5 ixgbe: remove ixgbe_napi_add/del_all references
There were still some references to napi_add/del_all left after the dynamic
vector allocation patch.  This patch removes those references since the
ixgbe_napi_add/del_all calls are no longer needed as the napi struct is
added when the vector is created, and deleted when the vector is freed.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-06 15:33:46 -07:00
Alexander Duyck
fdaff1ceac ixgbe: skb_record_rx_queue should record rx queue instead of vector
currently ixgbe_receive_skb is passing the vector index to
skb_record_rx_queue instead of the queue index.  This patch changes that so
that the ring index is passed instead.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-06 15:33:46 -07:00
Alexander Duyck
7a921c9362 ixgbe: make q_vectors dynamic to reduce netdev size
Currently the q_vectors are being allocated statically inside of the
adapter struct.  This increases the overall size of the adapter struct when
we can easily allocate the vectors dynamically.  This patch changes that
behavior so that the q_vectors are allocated dynamically and the napi
structures are automatically allocated inside of the q_vectors as needed.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-06 15:33:45 -07:00
David S. Miller
aba7453037 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	Documentation/isdn/00-INDEX
	drivers/net/wireless/iwlwifi/iwl-scan.c
	drivers/net/wireless/rndis_wlan.c
	net/mac80211/main.c
2009-04-29 20:30:35 -07:00
Ben Hutchings
6b73e10d2d ixgbe: Use generic MDIO definitions and functions
Compile-tested only.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-29 17:32:33 -07:00
Don Skidmore
dd4d8ca644 ixgbe: Use pci_wake_from_d3() instead of multiple pci_enable_wake()
We were calling pci_enable_wake() twice in a row for both D3_hot
and D3_cold.  This replaces those calls with a call to pci_wake_from_d3()
to avoid issues with PCI PM vs ordering constraints.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-29 00:22:31 -07:00
Nelson, Shannon
bc59fcda67 ixgbe: Clear out stray tx work on link down
Ayyappan at VMware noticed that we're missing this check from ixgbe which
is in our other drivers.  The difference with this implementation from our
other drivers is that this checks all the tx queues rather than just tx[0].

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-28 01:53:17 -07:00
Nelson, Shannon
835462fc5d ixgbe: Interrupt management update for 82599
Update the interrupt management to correctly handle greater
than 16 queue vectors.

Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-28 01:53:16 -07:00
Alexander Duyck
f8212f979f ixgbe: enable HW RSC for 82599
This patch enables hardware receive side coalescing for 82599 hardware.
82599 can merge multiple frames from the same TCP/IP flow into a single
structure that can span one ore more descriptors.  The accumulated data is
arranged similar to how jumbo frames are arranged with the exception that
other packets can be interlaced inbetween.  To overcome this issue a next
pointer is included in the written back descriptor which indicates the next
descriptor in the writeback sequence.

This feature sets the NETIF_F_LRO flag and clearing it via the ethtool set
flags operation will also disable hardware RSC.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-28 01:53:16 -07:00
Jesse Brandeburg
45a5ead022 ixgbe: enable hardware offload for sctp
Inspired by: Vlad Yasevich <vladislav.yasevich@hp.com>

This is the code to enable ixgbe for hardware offload support
of CRC32c on both transmit and receive of SCTP traffic.

only 82599 supports this offload, not 82598.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-28 01:53:15 -07:00
Alexander Duyck
182ff8dfdb igb/ixgbe: remove unecessary checks for CHECKSUM_UNNECESSARY
Both of these drivers do a check to verify ip_summed is set to
CHECKSUM_UNNECESSARY prior to passing the packet to GRO.  GRO itself
already does such a check so it is redundant and can be removed as this
will likely cause out of order issues when receiving a packet that didn't
pass checksum validation.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-28 01:53:13 -07:00
Waskiewicz Jr, Peter P
fa466e91bd ixgbe: Disallow SFP 1G modules in the SFP+ cages for 82598 and 82599
82598 and 82599 do not support SFP 1G modules.  Instead of allowing the
driver to load, but never get link, rejecting the module and displaying
a useful message is more preferrable.  The framework for displaying the
failure message already exists, now we just need to detect and reject the
SFP modules.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-27 03:15:42 -07:00
Waskiewicz Jr, Peter P
495dce123c ixgbe: Fix WoL functionality for 82599 KX4 devices
The current code writes the PME enabled bit in PCI config space which is
wrong.  This was needed for pre-release hardware, and was not removed from
the driver.  Also, we need to clear the WUS (wake up status) after we
resume.  Otherwise we can't wake for the same event again since it's still
asserted in the hardware.  Plus, the multicast lists were being written
improperly, causing multicast WoL to fail.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-27 03:14:48 -07:00
David S. Miller
e5e9743bb7 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/core/dev.c
2009-04-21 01:32:26 -07:00
Jesse Brandeburg
5438646724 ixgbe: fix link down initial state
As reported by Andrew Lutomirski <amluto@gmail.com>

All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice

This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.

This apparently confused *some* versions of networkmanager.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-20 02:00:37 -07:00
PJ Waskiewicz
2f3889f42e ixgbe: Fix the DCB PFC thresholds for 82599
The thresholds for the DCB priority flow control are incorrect for 82599.
This fixes the thresholds to be correct.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-17 01:16:28 -07:00
PJ Waskiewicz
f92ef20298 ixgbe: Fix DCB traffic class mapping for 82599
The traffic classes in hardware are not symmetrical for Rx and Tx.  Rx
is every 16 descriptor queues, Tx is not.  It runs 32-32-16-16-8-8-8 when
running with 8 traffic classes, and runs 64-32-16 when running with 4
traffic classes.  This patch fixes the mapping.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-17 01:16:28 -07:00
David S. Miller
a54bfa40fd Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2009-04-16 17:35:26 -07:00
Tony Breeds
2238aff5bb ixgbe: Be explict with what we are !'ing in ixgbe_sfp_config_module_task()
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'

Which I think is right.  Bracket to remove ambiguity.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 16:27:23 -07:00
Rafael J. Wysocki
9d8d05ae66 NET/ixgbe: Fix powering off during shutdown
Prevent ixgbe from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth).  For this purpose seperate ixgbe_shutdown() from ixgbe_suspend()
and use the appropriate PCI PM callbacks in both of them.

Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-16 02:15:25 -07:00
Wu Fengguang
af22ab1bd2 ixgbe: update real_num_tx_queues on changing num_rx_queues
Move the update of real_num_tx_queues from
ixgbe_acquire_msix_vectors() to ixgbe_set_num_queues(), to ensure it
be always in sync with num_tx_queues.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-14 21:54:07 -07:00
Wu Fengguang
95615d90a3 ixgbe: fix tx queue index
Don't do the num_tx_queues based masking on calculating tx queue
index.

 1) num_tx_queues is not always power-of-2, because it also depends on
    the online cpu numbers. So the masking could be a performance bug
    on a 6 cpu system.
 2) queue_mapping will be limited by real_num_tx_queues=num_tx_queues
    in the generic netdev function set_cur_queue_map(). So the bound
    limiting here is not necessary.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-14 21:53:48 -07:00
Tony Breeds
8d1c3c0746 ixgbe: Be explict with what we are !'ing in ixgbe_sfp_config_module_task()
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'

Which I think is right.  Bracket to remove ambiguity.

Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 02:48:03 -07:00
Peter P Waskiewicz Jr
04193058c1 ixgbe: Update get_physical_layer() calls, plus a version bump
Not all physical connection types are being correctly identified.  This
fixes that issue, and cleans up the logic to make it more maintainable.

Also clean up the code for device capabilities from the EEPROM to support
multiple SKUs of the same hardware.

Bump the version to reflect all the updates since the 82599 merge.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 02:48:02 -07:00
PJ Waskiewicz
1eb99d5ac4 ixgbe: Update the usage of orig_autoc to be more consistent
The orig_autoc variable tracks the original setting of the autonegotiate
state prior to trying a new speed.  The usage is inconsistent and not very
maintainable.  This patch updates the usage to make it more consistent.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 02:48:01 -07:00
PJ Waskiewicz
553b449784 ixgbe: Remove unnecessary PHY reset, properly identify multispeed fiber modules
This patch does two things:
1) On 82599, the PHY is emedded in the MAC.  On 82598, the SFP+ NIC has an external PHY.  The reset in the SFP+ setup patch for 82598 is unnecessary on 82599, and adds extra dead time to device initialization.  This removes that PHY reset for 82599 only.

2) On 82599, the SFP+ modules are multispeed fiber modules (10G/1G).  We need to make sure to identify them properly for the remaining init sections to properly set them up.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 02:48:01 -07:00
PJ Waskiewicz
04f165ef4f ixgbe: Move PHY ops initialization to centralize bus accesses
When PHY operations are determined, the PHY must be identified.  This
identification causes bus access, and should be contained within its own
routines.  This also helps the 82599 PHY init paths for both SFP+ and
KX/KX4 devices to be easier to maintain.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 02:48:00 -07:00
PJ Waskiewicz
d3e9c56caf ixgbe: Don't return error in flow control configuration if FC is off
When flow control is disabled, an invalid low/high watermark configuration
should not matter.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 02:48:00 -07:00
Don Skidmore
e80e887a95 ixgbe: add define to support 82599 64 IVAR registers
82599 supports 64 IVAR registers this patch adds a define to
allow us to access them.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 02:47:59 -07:00
Don Skidmore
6e4e87d68a ixgbe: add support for addition VT_CTL defines
These defines allow for definition of target pool for packets that
pass L2 filtering but didn't pass any of the pool filters.  They are
needed to reset the default pool.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 02:47:58 -07:00
Don Skidmore
d988eadbe2 ixgbe: fix IXGBE_MTQC values
IXGBE_MTQC_64VF was wrong and 32VF not defined at all.  This patch
corrects that.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 02:47:58 -07:00
PJ Waskiewicz
2132d38133 ixgbe: Enable another bit for flow control operation
The discard pause frames bit was not enabled, so flow control frames could
be passed up to the host.  Enabled DPF to keep the frames off the stack.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 02:47:57 -07:00
Alexander Duyck
d6c519e129 ixgbe: only allow WOL for 82599 KX4 NIC
All NICs were reporting WOL support when only the KX4 NIC is capable of
supporting WOL.  This patch adds a function to check for and exclude all
non-WOL capable nics from enabling WOL in ethtool.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 01:43:14 -07:00
PJ Waskiewicz
87c1201708 ixgbe: Move the LED blink code to common, since 82599 also uses it
The LED blink code is common for 82599 as well.  It should be moved to
ixgbe_common.c so both devices can use it, and not have it duplicated.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-11 01:43:12 -07:00
Yang Hongyang
284901a90a dma-mapping: replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:11 -07:00
Yang Hongyang
6a35528a83 dma-mapping: replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:10 -07:00
Mallikarjuna R Chilakala
f9ed88549e ixgbe: Fix potential memory leak/driver panic issue while setting up Tx & Rx ring parameters
While setting up the ring parameters using ethtool the driver can
panic or leak memory as ixgbe_open tries to setup tx & rx resources.
The updated logic will use ixgbe_down/up after successful allocation of
tx & rx resources

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-02 01:02:33 -07:00
Don Skidmore
71fd570b23 ixgbe: fix ethtool -A|a behavior
We were basicly ignoring ethtool users request for FC autoneg
and replying to queries with a "best guess".  This patch
enables the driver to store if we want to enable/disable
autoneg FC and do the correct behavior.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-02 01:02:32 -07:00
Mallikarjuna R Chilakala
a20a1199a8 ixgbe: Patch to fix driver panic while freeing up tx & rx resources
When network interface is made active we were not handling the error
scenarios properly to clean up rx & tx resources which might result in
a driver panic.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-02 01:02:32 -07:00
Alexander Duyck
44df32c592 ixgbe: refactor tx buffer processing to use skb_dma_map/unmap
This patch resolves an issue with map single being used to map a buffer and
then unmap page being used to unmap it.  In addition it handles any error
conditions that may be detected using skb_dma_map.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-02 01:02:31 -07:00
PJ Waskiewicz
8be0e4671d ixgbe: Fix 82598 MSI-X allocation on systems with more than 8 CPU cores
MSI-X allocation broke after the 82599 merge on systems with more than 8
CPU cores.  82598 drops back into MSI mode, which isn't sufficient to run
full, efficient 10G line rate.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-02 01:02:31 -07:00
Don Skidmore
cd7664f69f ixgbe: feature - driver to default with FC on.
In the past flow control wasn't enabled by default under the
incorrect assumption that this opened up us to a denial of
service attack.  However since any switch that forwarded flow
control would be extremely msiconfigured and/or buggy, this
concern no longer out weighs the preformance gains from
having FC enabled.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-02 01:02:30 -07:00
PJ Waskiewicz
ea4af4f447 ixgbe: Fix DCB netlink layer for 82599 to enable Priority Flow Control
The priority flow control settings from the netlink layer aren't taking
effect in the base driver.  The boolean pfc_mode_enable in the dcb_config
struct isn't being set, so the hardware configuration code is never
reached.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-02 01:02:28 -07:00
Don Skidmore
7c5b83230a ixgbe: Fix ethtool output with advertised mode.
Ethtool tries to get advertised speed from phy.autoneg_advertised.
However for copper media this wasn't happening until later do to
an other fix which moved mac.ops.setup_link_speed placement in
ixgbe_link_config(). This patch will display the default advertised
speeds if it can't yet get this information from phy.autoneg_advertised.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-02 01:02:27 -07:00
Alexander Duyck
b453368dfd ixgbe: fix build when DEBUG is defined
The ixgbe driver had issues when DEBUG was defined because the hw_dbg macro
was incomplete.  This patch completes the code based off of the code that
already existed in the igb module.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-02 01:02:27 -07:00
PJ Waskiewicz
bb3daa4a59 ixgbe: Allow Priority Flow Control settings to survive a device reset
When changing DCB parameters, ixgbe needs to have the MAC reset.  The way
the flow control code is setup today, PFC will be disabled on a reset.
This patch adds a new flow control type for PFC, and then has the netlink
layer take care of toggling which type of flow control to enable.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-26 01:13:51 -07:00
Stephen Hemminger
09a3b1f8b1 ixgbe: fix select_queue management
Convert ixgbe to use net_device_ops properly.
Rather than changing the select_queue function pointer
just check the flag.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 13:40:01 -07:00
Jesse Brandeburg
22d5a71b50 ixgbe: Fixup the watchdog interrupt scheduling on 82599
The watchdog will schedule an interrupt to help make sure queues are
cleaned in the case when an interrupt is missed, most likely due to very
high load.  On 82599, there are extra interrupt registers to account for
the larger number of MSI-X vectors (64 total for 82599 vs. 18 total for
82598).  These must be taken into account when performing this operation in
the watchdog.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 01:17:29 -07:00
PJ Waskiewicz
e63d976292 ixgbe: Correctly report Wake On LAN for 82599 KX4 devices
ethtool isn't reporting the support level of WoL for 82599 KX4 devices.
While the device does support WoL, ethtool was never updated to properly
report the level of support, nor will it allow ethtool to modify the type
of packets to listen for.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 01:17:27 -07:00
PJ Waskiewicz
03cfa20548 ixgbe: Fix PCI bus reporting on driver load for 82598 after 82599 merge
82598's PCI bus reporting on driver load was broken after 82599 merged.
This results in incorrect reporting, and an erroneous warning message
that the 82598 is in a PCIe slot that isn't fast enough to run 10GbE.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 01:17:25 -07:00
David S. Miller
2d6a5e9500 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/igb/igb_main.c
	drivers/net/qlge/qlge_main.c
	drivers/net/wireless/ath9k/ath9k.h
	drivers/net/wireless/ath9k/core.h
	drivers/net/wireless/ath9k/hw.c
2009-03-17 15:01:30 -07:00
Jesse Brandeburg
4df1046622 ixgbe: Cleanup some whitespace issues, fixup and add some comments
Cleanup a bit of whitespace, add some function header comments, and fix a
few comments around the driver.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:13 -07:00
PJ Waskiewicz
885125399e ixgbe: Two small fixes for 82599 when bringing the device down and for WoL
The Tx DMA unit should be disabled when bringing the device down.  Also,
the KX4 device with 82599 supports WoL, so we should clear the Wake Up
Status (WUS) after a PCIe slot reset.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:13 -07:00
Jesse Brandeburg
9891ca7cdc ixgbe: Add a few safety nets for register writes and descriptor cleanups
There are possible times that a driver may fail to completely initialize,
due to a buggy platform or a buggy kernel.  In those cases, we'd rather
fail gracefully instead of a panic.  Add a few safety checks to some
critical paths to try and prevent a panic in these corner-case situations.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:12 -07:00
Jesse Brandeburg
2a41ff8116 ixgbe: Cleanup on the Rx init path
This cleans up the following pieces of the Rx initialization path:

- Enable the ECC memory fault interrupt in OTHER causes.

- Fix an 82598 initialization of RDRXCTL when depending on RSS and VMDq to
be enabled.  We don't need these features enabled to safely set the MVMEN
bit to allow multiple SRRCTL register mappings into the RXDCTL registers.

- Fix the RSS initialization path to not stomp on DCB accidentally.  When
configuring the MRQC (multiple Rx queue contol) register, we want to make
sure we only OR in features as necessary, instead of full assignment.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:11 -07:00
Jesse Brandeburg
9a1a69adad ixgbe: Fix the Tx clean logic to return proper status
The Tx accounting when cleaning during NAPI was not completely properly.
We should use the work_limit to determine when to finish cleaning, and
use the same to return the cleaned status.  The impact of running like this
causes the NAPI clean for this Tx to get stuck in a scheduling loop, and
can result in Tx not getting cleaned, ending with a Tx hang and device
reset.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:11 -07:00
Jesse Brandeburg
4dd64df895 ixgbe: fix bug with napi add before request_irq
Occasionally if the driver was loaded in a system that
didn't support MSI-X or MSI and was on a shared interrupt,
the driver would then panic in NAPI on the first shared
interrupt because we hadn't called napi_add yet.

Solution: call napi_add before calling request_irq

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:10 -07:00
Jesse Brandeburg
509ee935ec ixgbe: Fix interrupt configuration for 82599
The interrupt models using EITR have changed in 82599.  The way the register
is laid out, the change is transparent to some of the existing code.
However, some of it isn't.  This patch fixes all the cases where EITR
handling is different than 82598.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:08 -07:00
PJ Waskiewicz
40dcd79a7b ixgbe: Disable DROP_EN for Rx queues
82599 mistakenly enabled drop on Rx queues in the packet buffer.  The
default mode should be store-and-forward from the FIFO.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:07 -07:00
PJ Waskiewicz
d51019a4da ixgbe: Fix an accounting problem when the Rx FIFO is full
The rx_no_dma_resources counter reported by ethtool -S ethX is not
counting correctly.  In 82599, the queue mappings for the counters need
to be mapped properly, and accounted for properly.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:07 -07:00
PJ Waskiewicz
1339b9e975 ixgbe: Fix get_supported_physical_layer() due to new 82599 PHY types
A purely cosmetic change.  Report which physical layer is present, instead
of PHY unknown.  82599 added new PHY types for the SFP+ devices, and this
was missed getting updated.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-14 12:41:06 -07:00
Chris Leech
e90d400c2b ixgbe: fix multiple unicast address support
Multiple unicast address support appears to have been broken with the
change to support net_device_ops.  This a regression from 2.6.28 to 2.6.29.

I'm not 100% on whether ndo_set_multicast_list can be NULL after this
or not.  If ndo_set_rx_mode is set everything _should_ be using it.

Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-13 13:40:36 -07:00
David S. Miller
fc1f209514 ixgbe: Fix some compiler warnings.
'pap' is never used in ixgbe_dcb_hw_config_82599()
and 'eec' in ixgbe_acquire_eeptom() is only used when
status == 0 but GCC has some trouble seeing that.

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-01 20:32:39 -08:00
PJ Waskiewicz
e8e26350f1 ixgbe: Add 82599 device id's, hook it up into the main driver.
With the hardware-specific code in place, add all supported device id's,
along with base driver changes to enable 82599 devices.  The devices
being enabled are:

8086:10f7: 82599EB 10 Gigabit KX4 Network Connection
8086:10fb: 82599EB 10 Gigabit Network Connection

The device 8086:10fb is a fully-pluggable SFP+ NIC.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-01 00:24:36 -08:00
PJ Waskiewicz
235ea828a1 ixgbe: Add DCB for 82599, remove BCN support
This patch adds the DCB (Data Center Bridging) support for 82599 hardware.
This is similar to how the 82598 DCB code works.

This patch also removes the BCN (Backwards Congestion Notification) netlink
configuration code from the driver.  BCN was a pre-standard congestion
notification framework, and was not what the IEEE body decided upon for
standard congestion management. QCN (802.1Qau), Quantized Congestion
Notification is the accepted standard, which is not supported by 82599,
hence we remove the support altogether.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-01 00:24:35 -08:00
PJ Waskiewicz
11afc1b1fd ixgbe: Add hardware specific initialization code for 82599 devices
This patch adds the hardware initialization code specific to 82599.  This
is similar to the 82598 hardware initialization code.  It also includes all
changes to the existing hardware init code to support 82599.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-01 00:24:33 -08:00
Jesse Brandeburg
32344a3940 ixbge: fix bug when using large pages and jumbo frames
it was pointed out on the list that ixgbe was failing when using 64kB pages
and large 16kB MTU.

since with a 64kB PAGE_SIZE MAX_SKB_FRAGS = 3, the way the driver was
configuring page usage was assuming 2kB is half a page, and was only
ever dmaing that much data to a half page.

(16kB - header size) / 2048 = 7 or 8 pages, which would far exceed 3

adjust the driver to account for these large pages, the hardware can
support DMA to up to 16kB for each descriptor.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-24 16:37:31 -08:00
Shannon Nelson
c7e4358ae8 ixgbe: Move ring features into an enum, allowing easier future maintenance
From: Shannon Nelson <shannon.nelson@intel.com>

The ring_feature member of ixgbe_adapter is statically allocated based on
the supported features of the device.  When a new feature is added, we need
to manually update the static allocation.  This patch makes the feature
list an enum, eliminating the need for multiple updates to the code when
adding a new feature.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-24 16:36:38 -08:00
Don Skidmore
54037505a5 ixgbe: fix for 82598 Si errata causing buffer overflow
The failure happens when an interrupt occurs and the driver is reading
EICR.  This read will cause a clear-by-read which leads to two TLP
being inserted in the PCIe retry buffer leading to an overflow of the
buffer and corruption of TLPs.

The solution is different depending where the reading of EICR takes place.

For ixgbe_msix_lsc() since we are in MSIX mode and know OCD is enabled a
clear-by-write is done instead of the normal clear-by-read.

For ixgbe_intr() 0xffffffff is written to EIMC before the read, masking the
interrupts.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-21 15:42:56 -08:00
Hannes Eder
1aef47c411 drivers/net/ixgbe: fix sparse warning: Should it be static?
Impact: Make symbol static.

Fix this sparse warning:
  drivers/net/ixgbe/ixgbe_82598.c:59:5: warning: symbol 'ixgbe_get_pcie_msix_count_82598' was not declared. Should it be static?

Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-17 17:37:58 -08:00
Breno Leitão
367681f4ec ixgbe: Removing the unused PAGE_USE_COUNT() macro.
Removing the unused PAGE_USE_COUNT() macro. Also removing the unused
pages variable at ixgbe_configure_rx() function.

Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-10 17:24:48 -08:00
Peter P Waskiewicz Jr
3e450669cc ixgbe: Fix a set_num_queues() bug that can result in num_(r|t)x_queues = 0
Now that our set_num_queues() routines for each feature are re-entrant, and
can be called at any point, they shouldn't zero out the feature's indices
or mask bits.  Subsequent calls into those routines for those features can
result in zero Rx and Tx queues being assigned, causing a panic later in
driver reinitialization.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-07 02:16:59 -08:00
Peter P Waskiewicz Jr
12207e498b ixgbe: Defeature Tx Head writeback
Tx Head writeback is causing multi-microsecond stalls on PCIe chipsets, due
to partial cacheline writebacks.  Removing this feature removes these
issues.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-06 21:47:24 -08:00
Peter P Waskiewicz Jr
0ecc061d19 ixgbe: Update flow control state machine in link setup
The flow control handling is overly complicated and difficult to maintain.
This patch cleans up the flow control handling and makes it much more
explicit.  It also adds 1G flow control autonegotiation, for 1G copper
links, 1G KX links, and 1G fiber links.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-06 21:46:54 -08:00
Peter P Waskiewicz Jr
34b0368c68 ixgbe: Display EEPROM version in ethtool -i queries
Currently ixgbe does not display the EEPROM version in ethtool -i, where
other drivers do.  The EEPROM version is located at offset 0x29.  This
patch adds support to display it.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-05 23:54:42 -08:00
Peter P Waskiewicz Jr
3201d3130e ixgbe: Update link setup code to better support autonegotiation of speed
The current code has some flaws in it when performing autonegotiation,
especially on KX/KX4 links.  This patch updates the code to better handle
the autonegotiation states on link setup.  The patch also removes a redundant
link configuration call on driver load, and moves link configuration to
the ->open() path.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-05 23:54:21 -08:00
Peter P Waskiewicz Jr
bc97114d3f ixgbe: Refactor set_num_queues() and cache_ring_register()
The current code to determine the number of queues the device will want
on driver initialization is ugly and difficult to maintain.  It also
doesn't allow for easy expansion for future features or future hardware.
This patch refactors these routines, and make them easier to deal with.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-05 23:53:59 -08:00
Peter P Waskiewicz Jr
3efac5a001 ixgbe: Update copyright dates, bump the driver version number
New year, new copyright date ranges.  Also bump the driver version
number to reflect many of the recent changes.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01 01:19:20 -08:00
Peter P Waskiewicz Jr
eb7f139ce5 ixgbe: Refactor MSI-X allocation mechanism
Our current MSI-X allocation mechanism does not support new hardware
at all.  It also isn't getting the actual number of supported MSI-X vectors
from the device.

This patch allows the number of MSI-X vectors to be specific to a device,
plus it gets the number of MSI-X vectors available from PCIe configuration
space.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01 01:18:58 -08:00
Don Skidmore
2f21bdd354 ixgbe: Add 82598 support for BX mezzanine devices
Add the device ID for BX devices using the 82598 MAC.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01 01:18:23 -08:00
Harvey Harrison
09640e6365 net: replace uses of __constant_{endian}
Base versions handle constant folding now.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01 00:45:17 -08:00
David S. Miller
0c8dfc830a net: Add skb_record_rx_queue() calls to multiqueue capable drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-27 16:22:32 -08:00
Don Skidmore
1e336d0fc9 ixgbe: add support KX/KX4 device
And support for the KX/KX4 mezzanine card.  Device id 0x10B6.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-26 20:57:51 -08:00
Don Skidmore
5b9c3cdd55 ixgbe: fix slow load times on 82598 nics
Load times for NICs that use i2c to communicate with the phy were taking
~4.5 sec per port.  This fix first checks to see if the link is already
up before calling get_link_capabilities, since if it is we don't need
query the phy for link state.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-26 20:57:17 -08:00
Herbert Xu
78b6f4ce58 ixgbe: Replace LRO with GRO
This patch makes ixgbe invoke the GRO hooks instead of LRO.  As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.

As GRO uses the napi structure to track the held packets, I've
modified the code paths involved to pass that along.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21 14:34:06 -08:00
Ben Hutchings
288379f050 net: Remove redundant NAPI functions
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21 14:33:50 -08:00
Peter P Waskiewicz Jr
1da100bb47 ixgbe: Fix usage of netif_*_all_queues() with netif_carrier_{off|on}()
netif_carrier_off() is sufficient to stop Tx into the driver.  Stopping the Tx
queues is redundant and unnecessary.  By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-19 16:55:03 -08:00
Don Skidmore
068c89b014 ixgbe: fix tag stripping for VLAN ID 0
Register VLAN ID 0 so that frames with VLAN ID 0 are received and get
their tag stripped when ixgbe is not in DCB mode.  VLAN ID 0 means
that the frame is 'priority tagged' only - it is not a VLAN, but the
priority value is the tag in valid.  The functions
ixgbe_vlan_rx_register() and ixgbe_vlan_rx_kill_vid() were moved up a
couple functions to correct compiling issues with this change.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-19 16:54:36 -08:00
Don Skidmore
15005a3204 ixgbe: fix dca issue with relaxed ordering turned on
The is an issue where setting Relaxed Ordering (RO) bit
(in a PCI-E write transaction) on 82598 causing the chipset
to drop DCA hints.  This patch forces RO not to be set for
descriptors as well as payload.  This will only be in effect
while DCA is enabled and no performance difference was
noticed in testing.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-19 16:54:13 -08:00
Peter P Waskiewicz Jr
d3fa472145 ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
The adapter rings are kcalloc()'d, but in set_ringparam() in ixgbe_ethtool,
we replace that memory from the vmalloc() pool.  This can result in a NULL
pointer reference when trying to modify the rings at a later time, or on
device removal.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 01:36:33 -08:00
Peter P Waskiewicz Jr
7adf1525be ixgbe: Fix NAPI enable/disable path when using DCB
This change allows DCB mode to change the number of queues, and presumably
the number of NAPI instances, safely.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 01:36:05 -08:00
Hannes Eder
e855aac805 drivers/net/ixgbe: fix sparse warnings: make symbols static
Fix this sparse warnings:

  drivers/net/ixgbe/ixgbe_82598.c:180:5: warning: symbol 'ixgbe_get_copper_link_capabilities_82598' was not declared. Should it be static?
  drivers/net/ixgbe/ixgbe_82598.c:245:5: warning: symbol 'ixgbe_setup_fc_82598' was not declared. Should it be static?
  drivers/net/ixgbe/ixgbe_82598.c:729:5: warning: symbol 'ixgbe_set_vmdq_82598' was not declared. Should it be static?
  drivers/net/ixgbe/ixgbe_82598.c:773:5: warning: symbol 'ixgbe_set_vfta_82598' was not declared. Should it be static?
  drivers/net/ixgbe/ixgbe_82598.c:897:5: warning: symbol 'ixgbe_read_analog_reg8_82598' was not declared. Should it be static?
  drivers/net/ixgbe/ixgbe_82598.c:919:5: warning: symbol 'ixgbe_write_analog_reg8_82598' was not declared. Should it be static?
  drivers/net/ixgbe/ixgbe_82598.c:940:5: warning: symbol 'ixgbe_read_i2c_eeprom_82598' was not declared. Should it be static?
  drivers/net/ixgbe/ixgbe_82598.c:1000:5: warning: symbol 'ixgbe_get_supported_physical_layer_82598' was not declared. Should it be static?
  drivers/net/ixgbe/ixgbe_dcb_82598.c💯5: warning: symbol 'ixgbe_dcb_config_packet_buffers_82598' was not declared. Should it be static?

Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-26 00:03:59 -08:00
Neil Horman
908a7a16b8 net: Remove unused netdev arg from some NAPI interfaces.
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter.  This patch cleans up that api by
properly removing it..

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-22 20:43:12 -08:00
Don Skidmore
bfb8cc31b1 ixgbe: fix the display of DCB control stats in ethtool
Priority flow contol statistics for Data Center Bridging (DCB) weren't
included in ethtool.  This patch adds them.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-21 20:11:04 -08:00
Don Skidmore
f4314e815e net: add DCNA attribute to the BCN interface for DCB
Adds the Backward Congestion Notification Address (BCNA) attribute to the
Backward Congestion Notification (BCN) interface for Data Center Bridging
(DCB), which was missing.  Receive the BCNA attribute in the ixgbe driver.
The BCNA attribute is for a switch to inform the endstation about the physical
port identification in order to support BCN on aggregated links.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2008-12-21 20:10:29 -08:00
Don Skidmore
1486a61ebc net: fix DCB setstate to return success/failure
Data Center Bridging (DCB) had no way to know if setstate had failed in the
driver.  This patch enables dcb netlink code to handle the status for the DCB
setstate interface.  Likewise it allows the driver to return a failed status
if MSI-X isn't enabled.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-21 20:09:50 -08:00
Jesse Brandeburg
5ecc361444 ixgbe: fix dma mapping unbalance
This issue was initially reported by Joerg Roedel <joerg.roedel@amd.com>
It appears that ixgbe has had a long standing bug where it was unmapping a different size than it had mapped.

ixgbe 0000:02:00.0: PCI-DMA: device driver frees DMA memory with different sizes than it mapped.
ixgbe 0000:02:00.0: PCI-DMA: device driver frees DMA memory with different size [device address=0x0000000003fed812] [map size=258 bytes] [unmap size=256 bytes]
Pid: 6178, comm: rmmod Not tainted 2.6.28-rc5 #4 Call Trace:
 [<ffffffff8022a2ae>] iommu_queue_inv_iommu_pages+0x5e/0x70
 [<ffffffff80225956>] check_unmap+0x1c6/0x240  [<ffffffff80225ff5>] debug_unmap_single+0xb5/0x110  [<ffffffffa0213997>] ixgbe_clean_rx_ring+0x147/0x220  [<ffffffffa0214d7d>] ixgbe_down+0x2fd/0x3d0 [ixgbe]  [<ffffffffa02150b3>] ixgbe_close+0x13/0xc0 [ixgbe]  [<ffffffff80431326>] dev_close+0x56/0xa0  [<ffffffff804313b3>] rollback_registered+0x43/0x220  [<ffffffff804315a5>] unregister_netdevice+0x15/0x60  [<ffffffff80431601>] unregister_netdev+0x11/0x20  [<ffffffffa021aef8>] ixgbe_remove+0x48/0x16e [ixgbe]  [<ffffffff80386ffc>] pci_device_remove+0x2c/0x60  [<ffffffff803ef929>] __device_release_driver+0x99/0x100
 [<ffffffff803efa48>] driver_detach+0xb8/0xc0  [<ffffffff803eea6e>] bus_remove_driver+0x8e/0xd0  [<ffffffff80387374>] pci_unregister_driver+0x34/0x90  [<ffffffff8026c6c7>] sys_delete_module+0x1c7/0x2a0  [<ffffffff802a9ce9>] do_munmap+0x349/0x390  [<ffffffff80374481>] __up_write+0x21/0x150  [<ffffffff8020c30b>] system_call_fastpath+0x16/0x1b

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-15 01:00:57 -08:00
Peter P Waskiewicz Jr
6fabd715e6 ixgbe: Implement PCIe AER support
This patch implements the PCIe Advanced Error Reporting callbacks in
ixgbe.  The 82598 hardware supports AER, so we enable it.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10 01:13:08 -08:00
Wang Chen
a4d2f34b7c ixgbe: function comment typo
Seems the ixgbe's code was copied from e1000.
The comment talks about something not exist.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-03 22:06:21 -08:00
Al Viro
feea6a574d ixgbe: section fixes
ixgbe_init_interrupt_scheme() is called from ixgbe_resume().  Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-27 15:34:07 -08:00
Jeff Kirsher
a46e534bc7 ixgbe: cleanup link up/down messages
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.  This also makes
the messages consistant with other Intel driver link messages.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-27 00:22:21 -08:00
David S. Miller
5b9ab2ec04 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/hp-plus.c
	drivers/net/wireless/ath5k/base.c
	drivers/net/wireless/ath9k/recv.c
	net/wireless/reg.c
2008-11-26 23:48:40 -08:00
Robert Olsson
cb13fc209f ixgbe: Naming interrupt vectors
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-25 16:44:39 -08:00
Jeff Kirsher
7a6b6f515f DCB: fix kconfig option
Since the netlink option for DCB is necessary to actually be useful,
simplified the Kconfig option.  In addition, added useful help text for the
Kconfig option.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-25 01:02:08 -08:00
Qinghuang Feng
ece4af18e0 driver/net/*: remove redundant argument comments
remove redundant argument comments in files of drivers/net/*

Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-23 15:46:55 -08:00
Wang Chen
9d2f472097 ixgbe: convert directly reference of netdev->priv
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-21 01:56:07 -08:00
Donald Skidmore
c4900be053 ixgbe: add SFP+ driver support
This patch adds support for SFP+ PHY in the following device ID's (10DB,
10F1, 10E1).  These SFP+ PHY's are accessed via an I2C interface so the
patch also includes functions to support this.

Another feature of note is that the PHY is pluggable and some
rearchitecting was needed to support this.

Signed-off-by: Donald Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 21:11:42 -08:00
Alexander Duyck
859ee3c438 DCB: Add support for DCB BCN
Adds an interface to configure the Backward Congestion Notification
(BCN) feature.  In a BCN capabale network, congestion notifications
from congested points out in the network can cause the end station
limit the rate of a given traffic flow.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 21:10:23 -08:00
Alexander Duyck
0eb3aa9bab DCB: Add interface to query the state of PFC feature.
Adds a netlink interface for Data Center Bridging (DCB) to get and set
the enable state of the Priority Flow Control (PFC) feature.
Primarily, this is a way to turn off PFC in the driver while DCB
remains enabled.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 21:09:23 -08:00
Alexander Duyck
33dbabc4a7 DCB: Add interface to query # of TCs supported by device
Adds interface for Data Center Bridging (DCB) to query (and set if
supported) the number of traffic classes currently supported by the
device for the two (DCB) features: priority groups (PG) and priority
flow control (PFC).

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 21:08:19 -08:00
Alexander Duyck
46132188bf DCB: Add interface to query for the DCB capabilities of an device.
Adds to the netlink interface for Data Center Bridging (DCB), allowing
the DCB capabilities supported by a device to be queried.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 21:05:08 -08:00
Alexander Duyck
2f90b8657e ixgbe: this patch adds support for DCB to the kernel and ixgbe driver
This adds support for Data Center Bridging (DCB) features in the ixgbe
driver and adds an rtnetlink interface for configuring DCB to the
kernel.  The DCB feature support included are Priority Grouping (PG) -
which allows bandwidth guarantees to be allocated to groups to traffic
based on the 802.1q priority, and Priority Based Flow Control (PFC) -
which introduces a new MAC control PAUSE frame which works at
granularity of the 802.1p priority instead of the link (IEEE 802.3x).

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 20:52:10 -08:00
Stephen Hemminger
008298231a netdev: add more functions to netdevice ops
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.

Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 20:14:53 -08:00
David S. Miller
6ab33d5171 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/ixgbe/ixgbe_main.c
	include/net/mac80211.h
	net/phonet/af_phonet.c
2008-11-20 16:44:00 -08:00
Stephen Hemminger
0edc352743 ixgb: convert to net_device_ops
Convert this driver to network device ops. Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-19 22:42:56 -08:00
Alexey Dobriyan
79aefa45b2 ixgbe: fix compilation with gcc-3.4
CC [M]  drivers/net/ixgbe/ixgbe_main.o
drivers/net/ixgbe/ixgbe_main.c: In function `ixgbe_intr':
drivers/net/ixgbe/ixgbe_main.c:1290: sorry, unimplemented: inlining failed in call to 'ixgbe_irq_enable': function body not available
drivers/net/ixgbe/ixgbe_main.c:1312: sorry, unimplemented: called from here
make[4]: *** [drivers/net/ixgbe/ixgbe_main.o] Error 1

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-19 14:17:02 -08:00
PJ Waskiewicz
74ad0a5421 ixgbe: Fix usage of netif_*_all_queues() with netif_carrier_{off|on}()
netif_carrier_off() is sufficient to stop Tx into the driver.  Stopping the Tx
queues is redundant and unnecessary.  By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-16 00:31:35 -08:00
Wang Chen
454d7c9b14 netdevice: safe convert to netdev_priv() #part-1
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
   netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.

This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-12 23:37:49 -08:00
David S. Miller
babcda74e9 drivers/net: Kill now superfluous ->last_rx stores.
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.

Drivers need not do it any more.

Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 21:11:17 -08:00
Jesse Brandeburg
0befdb3e0a ixgbe: add device support for 82598AT (copper 10GbE) adapters
Intel is currently shipping support for adapters with a phy
that does 10GBase-T (copper), which is 10 Gigabit ethernet
over standard Category 6 cabling.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-02 08:00:32 -05:00
Johannes Berg
7c510e4b73 net: convert more to %pM
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-27 17:47:26 -07:00
Jeff Garzik
5dd2d33228 [netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
We cannot select INTEL_IOATDMA in Kconfig as soon as MYRI10GE or IXGBE
is enabled since the former is not available on all architectures.

Just use a Kconfig bool {IXGBE,MYRI10GE}_DCA set to =y when DCA
support can actually be built.

[myri10ge portion written and signed-off-by] Brice Goglin <brice@myri.com>

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-16 05:09:31 -04:00
Harvey Harrison
b39d66a81f drivers/net: replace __FUNCTION__ with __func__
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:59:00 -04:00
Alexander Duyck
6988867473 ixgbe: whitespace/formatting cleanup
This patch cleans up some whitespace items, reorders a couple of functions, and removes some outdated comments.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:55:06 -04:00
Alexander Duyck
b3c8b4ba61 ixgbe: correctly add and remove napi queues
This patch corrects support for NAPI so that queues are correctly added and
removed during suspend/resume in the event that the number of MSI-X vectors
changes.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:55:05 -04:00
Peter P Waskiewicz
b46172402f ixgbe: Whitespace, copyright update and version number change patch
This patch cleans up a bit of whitespace issues with the driver, updates
the copyright information, and bumps the version number up.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:55:05 -04:00
Jeff Kirsher
51ac6445b1 ixgbe: bump version
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:55:04 -04:00
Jesse Brandeburg
9f8cdf4f06 ixgbe: xmit frame refactor
ixgbe_xmit_frame can be refactored to use fewer locals and better
utilize common kernel macros.

also fixed minor buglet with internal to driver vlan flag variable being
passed incorrectly.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:55:03 -04:00
Jesse Brandeburg
74ce8dd29b ixgbe: lower stack space usage
some functions were un-necessarily using local variables.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:55:02 -04:00
Jesse Brandeburg
2adc0511a3 ixgbe: cleanup defines
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:55:02 -04:00
Jesse Brandeburg
b9804972f5 ixgbe: move set_num_queues and call it after msix failure
This is partial preparation for a future patch which will extend
ixgbe_set_num_queues

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:55:01 -04:00
Jesse Brandeburg
7f8218752a ixgbe: refresh the ixgbe_down function
clean up the hardware shutdown sequence to prevent hardware
from continuing to send when resetting or unloading.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:55:00 -04:00
Jesse Brandeburg
c44ade9ef8 ixgbe: update to latest common code module
This is a massive update that includes infrastructure for further patches
where we will add support for more phy types and eeprom types.

This code is shared as much as possible with other drivers, so the code may
seem a little obtuse at times but wherever possible we keep to the linux
style and methods.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:59 -04:00
Jesse Brandeburg
f08482766b ixgbe: add clean rx many routine
in some configurations there can be more than one rx queue per vector
in msi-x mode.  Add functionality to be able to clean this without
changing the performance path single-rx-queue cleanup.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:59 -04:00
Jesse Brandeburg
f6af803f0b ixgbe: lro stats were not counted on first ethtool -Scall
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:58 -04:00
Jesse Brandeburg
c431f97ef9 ixgbe: fix ring reallocation in ethtool
changing ring sizes in ethtool needs to be robust.  If an allocation fails the
driver must continue operation, with the previous settings.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:57 -04:00
Jesse Brandeburg
b95f5fcb8b ixgbe: add device support for XF LR adapters
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:56 -04:00
Jesse Brandeburg
762f4c5710 ixgbe: recycle pages in packet split mode
most of the time we only need 1500 bytes for a packet which means
we don't need a whole 4k page for each packet.  Share the allocation
by using a reference count to the page and giving half to two
receive descriptors.  This can enable us to use packet split mode
all the time due to the performance increase of allocating half
the pages.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:56 -04:00
Jesse Brandeburg
ff819cfb5d ixgbe: fix bug with lots of tx queues
when using more than 8 tx queues you can overrun the 8 bit v_idx
field, so change it to 16 bits to represent the maximum number
of queues (one for each bit)

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:55 -04:00
Jesse Brandeburg
30efa5a363 ixgbe: fix initial interrupt throttle settings
ixgbe was incorrectly setting the throttle rate setting for all tx
queues and the driver has been refreshed to better handle a dynamic
interrupt mode as well as multiple queues.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:54 -04:00
Jesse Brandeburg
3d3d6d3cc2 ixgbe: fix ethtool disable csum for ipv6
ethtool was not disabling the correct netif flags when setting
checksum disable.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:54 -04:00
Jeff Kirsher
05857980cf ixgbe: fix pci_resource allocation as in other drivers
Form: Jesse Brandeburg <jesse.brandeburg@intel.com>

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:53 -04:00
Jesse Brandeburg
98c00a1c5d ixgbe: fix ethtool register dump
1) reading some of the registers in our hardware causes them to clear,
so don't read ICR in the ethtool register dump function.
2) several register iterators were not iterating

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:52 -04:00
Jesse Brandeburg
42c783c5b1 ixgbe: limit small mtu to minimum for ipv4 support
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:51 -04:00
Jesse Brandeburg
f47cf66e9c ixgbe: fix bug with shared interrupts
fix ixgbe bug reported with shared legacy interrupts

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:51 -04:00
Jesse Brandeburg
41fb924866 ixgbe: link change interrupt was not causing link event
Upon review a buglet was found where link change was not causing
an immediate link change event as it should.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:50 -04:00
Jesse Brandeburg
cf8280ee7b ixgbe: Update watchdog thread to accomodate longerlink_up events
This patch updates the link_up code and watchdog thread so that link_up
doesn't cause stack overflows due to long waits in interrupt context.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:49 -04:00
Jesse Brandeburg
ce94bf469e ixgbe: fix multicast address update
after the most recent patches, the driver was not using the
correct iterator for updating the receive address registers (RAR)

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:48 -04:00
Jesse Brandeburg
a1f96ee7cc ixgbe: fix dca defines to not have spaces
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:47 -04:00
Jesse Brandeburg
af72166f31 ixgbe: fix bug where using wake queue instead of start
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:54:47 -04:00
David S. Miller
17dce5dfe3 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	net/mac80211/mlme.c
2008-09-08 16:59:05 -07:00
Alexander Duyck
3be1adfb91 ixgbe: change config srrctl to only program one register per VMDq/RSS id
This change makes it so only one srrctl register is programmed per VMDq id, and if VMDq is not enabled it is one register per RSS queue.  Currently this function is working correctly for the multiqueue RSS and single queue cases, but if any advances features such as VMDq or DCB would have been enabled this function would have caused issues as it was not correct.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:08:22 -04:00
PJ Waskiewicz
4eeae6fd3f ixgbe: use different context for tso and offload
Change TSO offloads to use a different context than VLAN insertion
and Tx checksumming.  Hardware has separate registers internally for
storing these so use them.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:34 -04:00
Jesse Brandeburg
cc41ac7c00 ixgbe: fix dca hints going to wrong processor
hardware was configured incorrectly which led all hints to be
sent to queue[0]'s DCA configuration.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:34 -04:00
Jesse Brandeburg
e9990a9cd7 ixgbe: fix bug where lro settings are per ring
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:34 -04:00
Jesse Brandeburg
96b0e0f63b ixgbe: update dca to new interface, fix CONFIG_DCA_MODULE
DCA related fixes
=================
- ixgbe was not compiling and using DCA correctly if dca was a module
- DCA interface changed with new kernel
- ixgbe was not correctly configured to indicate DCA hints to the
  correct CPU.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:34 -04:00
Jesse Brandeburg
22f32b7a5a ixgbe: should not use HW_CSUM, should use IP* flags
as mentioned by Herbert, our hardware supports IP offloads, not full
checksum offloads for any protocol in existence (even though the
hardware just provides generic csum support over any range of bytes)

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:33 -04:00
Jesse Brandeburg
7c6e0a436d ixgbe: Lock RSS seed, move rx_buf_len to the rx_ring
This locks the seed down so loading/unloading the driver will present
predictable hashing from RSS.  Also move the rx_buf_len out of the adapter
struct, and into the Rx ring struct.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:33 -04:00
Jesse Brandeburg
e01c31a5f7 ixgbe: Implement Tx Head Writeback
Enable Tx Head Writeback in the hardware.  This helps performance by
removing adapter writebacks to descriptors on transmit completion.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:33 -04:00
Jesse Brandeburg
2b9ade935c ixgbe: disable flow control by default
Since the adapter cannot tell what the remote end's flow control capability
is through auto-neg, we must turn off flow control by default.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:33 -04:00
Jesse Brandeburg
3a581073e0 ixgbe: Cleanup references to Tx and Rx rings to becommon across the driver
Cleanup all the different references to the Tx ring and Rx ring structures
and make them common across the driver.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:33 -04:00
Jesse Brandeburg
036c9b0970 ixgbe: do not update stats twice each receive
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:33 -04:00
Christopher Leech
2c5645cf65 ixgbe: Implement HAVE_SET_RX_MODE
Implement HAVE_SET_RX_MODE in the driver for MC and UC lists.

Signed-off-by: Christopher Leech <christopher.leech@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:32 -04:00
Jesse Brandeburg
9da09bb1b8 ixgbe: add little endian annotations for sparse
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:32 -04:00
Jesse Brandeburg
712744bebe ixgbe: fix rx csum return status misinterpretation
the driver was misinterpreting rx_csum return value in the descriptor
so occassionally we would indicate an rx_csum error in our stats
when there was none.  This would have no effect on traffic because
we would just hand the packet to the stack anyway without the offload
flag set, but would increase CPU for those packets that needed a recompute.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 10:03:32 -04:00
Andy Gospodarek
15e79f24b6 ixgbe: initialize interrupt throttle rate
This commit dropped the setting of the default interrupt throttle rate.

commit 021230d40a
Author: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Date:   Mon Mar 3 15:03:45 2008 -0800

    ixgbe: Introduce MSI-X queue vector code

The following patch adds it back.  Without this the default value of 0
causes the performance of this card to be awful.  Restoring these to the
default values yields much better performance.

This regression has been around since 2.6.25.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: stable@kernel.org [2.6.25 and later]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03 09:26:18 -04:00
Alexander Duyck
3d01625a4f ixgbe: fix vlan filtering
VLAN filtering is broken, due to reading the incorrect register for
the VLAN filtering settings.  Fixed by reading/writing the correct
register.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-27 05:14:32 -04:00
Jesse Brandeburg
8d792cd990 ixgbe: add cx4 device ID
This is a simple device ID add for adapters that support
CX4 (copper infiniband style cable) connectors for 10GbE.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-08-14 04:42:41 -04:00
Jesse Brandeburg
bb5d10ac8c ixgbe: remove device ID for unsupported device
The ixgbe driver was untested with device ID 8086:10c8 but still advertises
support.  Currently if this device is present in the system when the driver
is loaded, the system will panic.
Remove this device ID until full support can be tested with available
hardware.  This patch is necessary for 2.6.24, 2.6.25 and 2.6.26

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-22 19:31:00 -04:00
Jeff Kirsher
d55b53fff0 igb/ixgbe/e1000e: resolve tx multiqueue bug
With the recent changes to tx mutiqueue, igb/ixgbe/e1000e was not calling
netif_tx_start_all_queues() before calling netif_tx_wake_all_queues().
This causes an issue during loading of the driver.

In addition, updated e1000e to use the updated tx mutliqueue api.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-18 04:33:03 -07:00
David S. Miller
fd2ea0a79f net: Use queue aware tests throughout.
This effectively "flips the switch" by making the core networking
and multiqueue-aware drivers use the new TX multiqueue structures.

Non-multiqueue drivers need no changes.  The interfaces they use such
as netif_stop_queue() degenerate into an operation on TX queue zero.
So everything "just works" for them.

Code that really wants to do "X" to all TX queues now invokes a
routine that does so, such as netif_tx_wake_all_queues(),
netif_tx_stop_all_queues(), etc.

pktgen and netpoll required a little bit more surgery than the others.

In particular the pktgen changes, whilst functional, could be largely
improved.  The initial check in pktgen_xmit() will sometimes check the
wrong queue, which is mostly harmless.  The thing to do is probably to
invoke fill_packet() earlier.

The bulk of the netpoll changes is to make the code operate solely on
the TX queue indicated by by the SKB queue mapping.

Setting of the SKB queue mapping is entirely confined inside of
net/core/dev.c:dev_pick_tx().  If we end up needing any kind of
special semantics (drops, for example) it will be implemented here.

Finally, we now have a "real_num_tx_queues" which is where the driver
indicates how many TX queues are actually active.

With IGB changes from Jeff Kirsher.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-17 19:21:07 -07:00
David S. Miller
09e83b5d7d netdev: Kill NETIF_F_MULTI_QUEUE.
There is no need for a feature bit for something that
can be tested by simply checking the TX queue count.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-17 19:21:03 -07:00
Patrick McHardy
78ed11a56b netdrv intel: always enable VLAN filtering except in promiscous mode
Currently VLAN filtering is enabled when the first VLAN is added.
Obviously before that there's no point in receiving any VLAN packets.
Now that we disable VLAN filtering in promiscous mode, we can keep
the VLAN filters enabled the remaining time.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-16 20:16:14 -07:00
Patrick McHardy
746b9f0228 netdrv intel: disable VLAN filtering in promiscous mode
As discussed in this thread:

http://www.mail-archive.com/netdev@vger.kernel.org/msg53976.html

promiscous mode means to disable *all* filters. Currently only unicast
and multicast filtering is disabled. This patch changes all Intel
drivers to also disable VLAN filtering.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-16 20:15:45 -07:00
David S. Miller
b19fa1fa91 net: Delete NETDEVICES_MULTIQUEUE kconfig option.
Multiple TX queue support is a core networking feature.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-08 23:14:24 -07:00
David S. Miller
332e4af80d Merge branch 'davem-next' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 2008-06-28 21:28:46 -07:00
David S. Miller
1b63ba8a86 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/wireless/iwlwifi/iwl4965-base.c
2008-06-28 01:19:40 -07:00
Paul Larson
6f4a0e45c6 ixgbe: fix EEH recovery during reset on PPC
EEh is not recovering in a resonable amount of time on PPC during
ixgbe_down().

Signed-off-by: Paul Larson <pl@us.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-27 01:27:46 -04:00
Mallikarjuna R Chilakala
177db6ffd0 ixgbe: add LRO support
Support for in-kernel LRO with the ability to enable/disable via ethtool
based on comments from Ben Hutchings.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-24 23:06:19 -04:00
David S. Miller
4ae127d1b6 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/smc911x.c
2008-06-13 20:52:39 -07:00
Jeff Kirsher
ad31c402b4 ixbge: allow vlan devices to use TSO and TCP CSUM offload
Using the new interface for propagating device feature flags into VLAN
devices, turn on TSO and CSUM offload on VLAN devices.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-11 21:58:42 -04:00
Jeff Kirsher
ff68cdbf86 ixgbe: fix typo
Define names were accidently transposed.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-10 18:20:15 -04:00
Wendy Xiong
fb3b27bc00 ixgbe: save and restore pcie/msi state to support EEH recovery
To enable EEH support for pci-express network adapters, pcie/msi state
needs to be saved and restored for that adapter.

Tested this EEH patch with Intel 10G pci-express ixgbe adapter.

Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 02:07:13 -04:00
Denis V. Lunev
652f093fdf Compilation fix for ixgbe_main.c.
Under CONFIG_DCA the compilation is broken since the commit
bd0362dde0 (ixgbe: Add optional
DCA infrastructure).

IXGBE_SUCCESS is not defined anywhere, replace it with 0.

Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-28 22:14:53 -04:00
Auke Kok
ef8500457b ixgbe: Increment version
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-17 07:49:28 -04:00
Jeb Cramer
bd0362dde0 ixgbe: Add optional DCA infrastructure
82598 cards and up support DCA, which enables the chipset to warm
up the caches for upcoming payload data. This code makes the
driver plug into the CONFIG_DCA infrastructure that was merged
earlier.

Signed-off-by: Jeb Cramer <cramerj@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-17 07:49:28 -04:00
Ayyappan Veeraiyan
f494e8faa7 ixgbe: Introduce adaptive interrupt moderation
82598 can produce a formidable interrupt rate, and is largely
unusable without some form of moderation. The default behaviour
before this patch is to limit irq's to a reasonable number.
However, just like our other drivers we can reduce latency
for small packet-type traffic considerably by allowing the
irq rate to go up dynamically.

This patch introduces a simple irq moderation algorithm based
on traffic analysis. The driver will use more CPU to service
small packets quicker but will perform the same on bulk traffic
as the old code.

Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-17 07:49:28 -04:00