div6 clock should not use arch_flags for clk_rate_table_build,
because SH_CLK_DIV6_EXT doesn't care .arch_flags.
clk->freq_table[] will be all CPUFREQ_ENTRY_INVALID without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I missed that coccinelle does not fix up header files by default.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: <lethal@linux-sh.org>
Convert the SuperH clocks framework and shared interrupt handling
code to using struct syscore_ops instead of a sysdev classes and
sysdevs for power managment.
This reduces the code size significantly and simplifies it. The
optimizations causing things not to be restored after creating a
hibernation image are removed, but they might lead to undesirable
effects during resume from hibernation (e.g. the clocks would be left
as the boot kernel set them, which might be not the same way as the
hibernated kernel had seen them before the hibernation).
This also is necessary for removing sysdevs from the kernel entirely
in the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Clear the valid flag is in the INTC code.
Without this fix bit 7 of the sense register
is mistakenly set.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove kobject.h from files which don't need it, notably,
sched.h and fs.h.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently the root node is initialized by way of kzalloc on the parent
data structure, which by chance happens to do the bulk of what an
explicit initialization does with GFP_NOWAIT semantics. This however is
more by luck than by design, and as we ideally want to permit radix node
allocations access to the emergency pools anyways, add in the proper
initializer with the desired mask.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The disabling of the init op for non-legacy clocks neglected to do the
same in the core clock framework, resulting in a build failure. Fix it
up.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that clk_set_rate_ex() is gone, there is also no way to get at rate
setting algo id, which is now also completely unused. Kill it off before
new clock ops start using it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the refactoring of the SH7722 clock framework some time ago this
abstraction has become unecessary. Kill it off before anyone else gets
the bright idea to start using it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The radix tree retry logic got a bit of an overhaul and subsequently
broke the virtual IRQ subgroup build. Simply switch over to
radix_tree_deref_retry() as per the filemap changes, which the virq
lookup logic was modelled after in the first place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CC drivers/sh/clk/core.o
drivers/sh/clk/core.c: In function 'clk_round_parent':
drivers/sh/clk/core.c:574: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'unsigned int'
drivers/sh/clk/core.c:594: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'unsigned int'
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Sometimes it is possible and reasonable to adjust the parent clock rate to
improve precision of the child clock, e.g., if the child clock has no siblings.
clk_round_parent() is a new addition to the SH clock-framework API, that
implements such an optimization for child clocks with divisors, taking all
integer values in a range.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
According to the linux/clk.h definition we should be handing back an
errno value or a valid rate. This fixes up the case where 0 can be
returned for invalid frequencies or cases where rounding has no
selectable candidate.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's no need to iterative over every single irq_desc when we can
already work out which IRQs have a backing descriptor via the shiny new
for_each_active_irq(). Switch to that instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the genirq code provides an IRQ bitmap of its own and the
necessary API to manipulate it, there's no need to keep our own version
around anymore.
In the process we kill off some unused IRQ reservation code, with future
users now having to tie in to the genirq API as normal.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This shuffles the clock framework code around to a drivers/sh/clk subdir,
to follow the intc split up. This will make it easier to subsequently
break things out as well as plug in different helpers for non-CPG users.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The end condition of for_each_frequency should care about
both clk_rate_table_round and clk_rate_div_range_round,
and using "correct max size" is a natural idea in later function.
To avoid data over flow, this patch didn't modify
clk_rate_div_range_round side as .max = div_max + 1.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When updating the iterator macro an old argument assignment was used on
the initial assignment causing a fault on the table rounding. Fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a new clk_rate_div_range_round() for implementing rate rounding
by divisor ranges. This can be used trivially by clocks that support
arbitrary ranged divisors without the need for rate table construction.
This should only be used by clocks that both have large divisor ranges in
addition to clocks that will never be arbitrarily scaled, as the lack of
a backing frequency table will prevent cpufreq from being able to do much
of anything with them.
Primarily intended for use as a ->recalc helper.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the only assisted rate rounding is frequency table backed, but
there are cases where it's impractical to use a frequency table for
certain clocks (such as the FSIDIV case, which supports 65535 divisors),
and we wish to reuse the same rate rounding algorithm.
This breaks out the core of the rate rounding logic in to its own helper
routine and shuffles the frequency table logic around, switching to using
an iterator for the generic helper routine.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements support for ioremapping of register windows that
encapsulate clock control registers used by a struct clk, with
transparent sibling inheritance.
Root clocks at the top of a given topology often encapsulate the entire
register space of all of their sibling clocks, so this mapping can be
done once and handed down. A given clock enable/disable case maps out to
a single bit in a shared register, so this prevents creating multiple
overlapping mappings.
The mapping case breaks down in to a couple of different situations:
- Sibling clocks without a specific mapping.
- Root clocks without a specific mapping.
- Any of sibling/root clocks with a specific mapping.
Sibling clocks with no specified mapping will grovel up the clock chain
and install the root clock mapping unconditionally at registration time.
Root clocks without their own mappings have a dummy BSS-initialized
mapping inserted that is handed down the chain just like any other
mapping. This permits all of the sibling clock ops to read/write using
the mapping offsets without any special configuration, enabling them to
not care whether access ultimately goes through translatable or
untranslatable memory.
Any clock with its own mapping will have the window initialized at
registration time and be ready for use by its clock ops. Failure to
establish the mapping will prevent registration, so no additional sanity
checks are needed. Sibling clocks that double as parents for the moment
will not propagate their mapping down, but this is easily tunable if the
need arises.
All clock mappings are kref refcounted, with each instance of mapping
inheritance incrementing the refcount.
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove "name" and "id" from drivers/sh/ struct clk.
The struct clk members "name" and "id" are not used
now when matching is done through clkdev.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits up the sh intc core in to something more vaguely resembling
a subsystem. Most of the functionality was alread fairly well
compartmentalized, and there were only a handful of interdependencies
that needed to be resolved in the process.
This also serves as future-proofing for the genirq and sparseirq rework,
which will make some of the split out functionality wholly generic,
allowing things to be killed off in place with minimal migration pain.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If lookups happen while the radix node still points to a subgroup
mapping, an IRQ hasn't yet been made available for the specified id, so
error out accordingly. Once the slot is replaced with an IRQ mapping and
the tag is discarded, lookup can commence as normal.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Many interrupts that share a single mask source but are on different
hardware vectors will have an associated register tied to an INTEVT that
denotes the precise cause for the interrupt exception being triggered.
This introduces the concept of IRQ subgroups in the intc core, where
a virtual IRQ map is constructed for each of the pre-defined cause bits,
and a higher level chained handler takes control of the parent INTEVT.
This enables CPUs with heavily muxed IRQ vectors (especially across
disjoint blocks) to break things out in to a series of managed chained
handlers while being able to dynamically lookup and adopt the IRQs
created for them.
This is largely an opt-in interface, requiring CPUs to manually submit
IRQs for subgroup splitting, in addition to providing identifiers in
their enum maps that can be used for lazy lookup via the radix tree.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a scheme roughly analogous to the PowerPC virtual to
hardware IRQ mapping, which we use for IRQ to per-controller ID mapping.
This makes it possible for drivers to use the IDs directly for lookup
instead of hardcoding the vector.
The main motivation for this work is as a building block for dynamically
allocating virtual IRQs for demuxing INTC events sharing a single INTEVT
in addition to a common masking source.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The gpiolib debugfs entry takes a hammer approach and iterates over all
of the potential GPIOs, regardless of their type. The SH PFC code on the
other hand contains a variable mismash of input/output/function types
spread out sparsely, leading to situations where the debug code can
trigger an out of range enum for the type. Since we already have an error
path for out of range enums, we can just hand that up to the higher level
instead of the current BUG() behaviour.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the pinmux code is a one-way thing, but there's nothing
preventing an unregistration if no one has grabbed any of the pins.
This will permit us to save a bit of memory on systems that require pin
demux for certain peripherals in the case where registration of those
peripherals fails, or they are otherwise not attached to the system.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some controllers will need to be initialized lazily due to pinmux
constraints, while others may simply have no need to be brought online if
there are no backing devices for them attached. In this case it's still
necessary to be able to reserve their hardware vector map before dynamic
IRQs get a hold of them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in hardware IRQ auto-distribution support for SH-X3 proto CPUs,
following the SH7786 support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was killed off by a simplification patch previously that failed to
take the cpufreq use case in to account, so reinstate the old bounding
logic. The lowest rate bounding on the other hand was broken in that it
never actually got assigned a rate and the best fit rate was instead just
getting lucky based on the ordering of the rate table, fix this up so the
code actually does what it was intended to do originally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for reparenting of div6 clocks on SuperH and SH-Mobile SoCs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The use of highest and lowest in clk_rate_table_round() is completely bogus
and superfluous. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
To actually output the _new_ clock rate it first has to be set.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Wrapping pr_fmt to the KBUILD_MODNAME prefix seems to be the trendy
thing to do these days, so just do that instead of manually tidying
up the stragglers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Teach SH-Mobile ARM how to make use of the shared SH clock
framework. This commit is one atomic switch that dumps the
local hackery and instead links in the shared clock framework
code in drivers/sh. A few local functions are kept in clock.c.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the CPG helpers to drivers/sh/clk-cpg.c V2.
This to allow SH-Mobile ARM to share the code with
SH. All functions except the legacy CPG stuff is moved.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V2 of the SH clock framework move from
arch/sh/kernel/cpu/clock.c to drivers/sh/clk.c. All
code except the following functions are moved:
clk_init(), clk_get() and clk_put().
The init function is still kept in clock.c since it
depends on the SH-specific machvec implementation.
The symbols clk_get() and clk_put() already exist in
the common ARM clkdev code, those symbols are left in
the SH tree to avoid duplicating them for SH-Mobile ARM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements support for hardware-managed IRQ balancing as implemented
by SH-X3 cores (presently only hooked up for SH7786, but can probably be
carried over to other SH-X3 cores, too).
CPUs need to specify their distribution register along with the mask
definitions, as these follow the same format. Peripheral IRQs that don't
opt out of balancing will be automatically distributed at the whim of the
hardware block, while each CPU needs to verify whether it is handling the
IRQ or not, especially before clearing the mask.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for hardware-assisted userspace irq masking for
special priority levels. Due to the SR.IMASK interactivity, only some
platforms implement this in hardware (including but not limited to
SH-4A interrupt controllers, and ARM-based SH-Mobile CPUs). Each CPU
needs to wire this up on its own, for now only SH7786 is wired up as an
example.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The printk loglevels are all over the place, make them a bit more
coherent, and add some registration notification while we're at it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the sysdevs are simply numbered based on the list position,
without having any direct way of figuring out which controller these are
actually mapping to. This provides a name attr for mapping out the chip
name.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: remove duplicated #include
sh: Export uncached helper symbols.
sh: Fix up NUMA build for 29-bit.
serial: sh-sci: Fix build failure for non-sh architectures.
sh: Fix up uncached offset for legacy 29-bit mode.
sh: Support CPU affinity masks for INTC controllers.
Extend the INTC code with ioremap() support V2.
Support INTC controllers that are not accessible through
a 1:1 virt:phys window. Needed by SH-Mobile ARM INTCS.
The INTC code behaves as usual if the io window resource
is omitted. The slow phys->virt lookup only happens during
setup. The fast path code operates on virtual addresses.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the INTC code to warn and return an error code
in the case of memory allocation failure.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This hooks up the ->set_affinity() for the INTC controllers, which can be
done as just a simple copy of the cpumask. The enable/disable paths
already handle SMP register strides, so we just test the affinity mask in
these paths to determine which strides to skip over.
The early enable/disable path happens prior to the IRQs being registered,
so we have no affinity mask established at that point, in which case we
just default to CPU_MASK_ALL. This is left as it is to permit the force
enable/disable code to retain existing semantics.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently there's an ordering issue with the chained handler change
which places the set_irq_chip() after set_irq_chained_handler(). This
causes a warning to be emitted as the IRQ chip needs to be set first.
However, there is the caveat that redirect IRQs can't use the parent
IRQ's irq chip as they are just dummy redirects, resulting in
intc_enable() blowing up when set_irq_chained_handler() attempts to
start up the redirect IRQ. In these cases we can just use dummy_irq_chip
directly, as we already extract the parent IRQ and chip from the redirect
handler.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the shared INTC code with force_disable support to
allow keeping mask bits statically disabled. Needed for
SDHI support to mask out unsupported interrupt sources.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the shared INTC code to use
set_irq_chained_handler() for intc_redirect_irq().
With this in place request_irq() on a merged irq
which has been redirected will now return -EINVAL
instead of 0 together with a crash. This thanks to
the protection of the IRQ_NOREQUEST flag set for
chained interrupt handlers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the shared INTC code with force_enable support to
allow keeping mask bits statically enabled. Needed by
upcoming INTC SDHI patches that mux together a bunch of
vectors to a single linux interrupt which is masked by
a priority register, but needs individual mask bits
constantly enabled.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the INTC code by moving all vectors,
groups and registers from struct intc_desc to struct
intc_hw_desc.
The idea is that INTC tables should go from using the
macro(s) DECLARE_INTC_DESC..() only to using struct
intc_desc with name and hw initialized using the macro
INTC_HW_DESC(). This move makes it easy to initialize
an extended struct intc_desc in the future.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Reuse the SuperH INTC code on ARM by using set_irq_flags()
to set IRQF_VALID on ARM platforms.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This just reworks the existing create_irq_on_node() in to the new
create_irq_nr() which is generally exposed. This permits boards that
haven't converted over to sparseirq to try and use their existing ranges,
rather than having arbitrary vectors assigned to them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the PFC code with some clarifying
comments together with a functional change. The change
allows function type of GPIO to select any type of enum
in their MARK lists. Without this patch only function
type of enums are allowed in MARK lists.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the resume from hibernation
in the intc sysdev device when it manages 'redirect' irq
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For some reason this was using pr_info() nested under an ifdef DEBUG.
While this is appealing in that it circumvents the effort necessary to
change ones loglevel, it's not terribly practical. So, convert it over
to pr_debug().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the PFC code is exposed for other architectures, use the common
__raw_xxx() routines instead of the ctrl_xxx() ones. This will be needed
for ARM-based SH-Mobiles amongst others.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This file breaks out the SuperH PFC code from
arch/sh/kernel/gpio.c + arch/sh/include/asm/gpio.h
to drivers/sh/pfc.c + include/linux/sh_pfc.h.
Similar to the INTC stuff. The non-SuperH specific
file location makes it possible to share the code
between multiple architectures.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Different CPUs will have different starting vectors, with varying
amounts of reserved or unusable vector space prior to the first slot.
This introduces a legacy vector reservation system that inserts itself in
between the CPU vector map registration and the platform specific IRQ
setup. This works fine in practice as the only new vectors that boards
need to establish on their own should be dynamically allocated rather
than arbitrarily assigned. As a plus, this also makes all of the
converted platforms sparseirq ready.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for dynamic IRQ allocation/deallocation for all parts
using the SH-style vectored IRQs. While this is not inherently
INTC-specific, the INTC code is the main tie-in for vectored IRQ
registration, and is the only place that a full view of the utilized
vector map is possible.
The implementation is fairly straightforward, implementing a flat IRQ map
where each registered vector is reserved, allowing us to scan for holes
and dynamically wire up IRQs lazily later on in the boot stage. This
piggybacks on top of sparseirq in order to make the best use of the
available vector space.
Dynamic IRQs can be used for any number of things, ranging from MSI in
the SH-X3 PCIe case down to demux vectors for board FPGAs and system
controllers that presently allocate an arbitrary range. In the latter
case, this also allows those platforms to use sparseirq without blowing
up, which brings us one step closer to enabling sparseirq as the default
for all platform and CPU combinations.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently this is ifdef'ed under SH-3 and SH-4A, but there are other CPUs
that will need this as well. Given the size of the existing data
structures, this doesn't cause any additional cacheline utilization for
the existing users, so has no direct impact on the data structures.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Maple's abuse of PHYSADDR() likewise can be converted to virt_to_phys()
for its cases, although in practice this really wants explicit remapping.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the simplified multi-evt handling when sparseirq support is
enabled. While vectors are redirected through the single unique masking
source, each one of the redirected vectors still requires its own backing
irq_desc, which needs to be manually allocated in the sparseirq case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes the way in which "multi-evt" interrups are handled.
The intc_evt2irq_table and related intc_evt2irq() have been removed and
the "redirecting" handler is installed for the coupled interrupts.
Thanks to that the do_IRQ() function don't have to use another level
of indirection for all the interrupts...
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It is possible for the CPU to re-enable it's interrupt block bit
before the write to the interrupt controller has actually masked out
the external interupt at the controller. We get around this by
reading back from the interrupt controller which will ensure the
write has happened.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the slab allocators are available much earlier, this triggers a
the slab_is_available() warning when registering the interrupt
controller. Convert to kzalloc() with GFP_NOWAIT, as per the generic
changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the dependent patches are merged, we are ready to enable
sparseirq support. This simply adds the Kconfig option, and then converts
from the _cpu to the _node allocation routines to follow the upstream
sparseirq API changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
irq_to_desc_alloc_cpu() has been renamed to irq_to_desc_alloc_node() in
-next, but as we can not presently enable SPARSE_IRQ without the early
irq_desc alloc patch, protect it with an ifdef until the interface has
settled and we are ready to enable it system-wide.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This hooks in irq_to_desc_alloc_cpu() to the necessary code paths in the
intc and ipr controller registration paths. As these are the primary call
paths for all SH CPUs, this alone will make all CPUs sparse IRQ ready.
There is the added benefit now that each CPU contains specific IPR and
INTC tables, so only the vectors with interrupt sources backing them will
ever see an irq_desc instantiation. This effectively packs irq_desc
down to match the CPU, rather than padding NR_IRQS out to cover the valid
vector range.
Boards with extra sources will still have to fiddle with the nr_irqs
setting, but they can continue doing so through the machvec as before.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It's required for all modules loaded in the previous runtime
session because not initilized duing the kernel start-up.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add set_irq_wake() support to intc using sysdev and suspend.
The intc controllers are put on a list at registration time
and registered as sysdev devices later on during the boot.
The sysdev class suspend callback is used to find irqs with
wakeup enabled belonging to our intc controller. Such irqs
are simply enabled so wakeup interrupts may reach the cpu.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Modify the intc code to install a disable callback. The current
solution without a disable callback results in use of the
generic default_disable() function. This function is a no-op
so suspend_device_irqs() will not disable any intc interrupts
at suspend time without this patch. Also, install enable and
shutdown callbacks while at it.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of keeping the single vector -> single linux irq mapping
we extend the intc code to support merging of vectors to a single
linux irq. This helps processors such as sh7750, sh7780 and sh7785
which have more vectors than masking ability. With this patch in
place we can modify the intc tables to use one irq per maskable
irq source. Please note the following:
- If multiple vectors share the same enum then only the
first vector will be available as a linux irq.
- Drivers may need to be rewritten to get pending irq
source from the hardware block instead of irq number.
This patch together with the sh7785 specific intc tables solves
DMA controller irq issues related to buggy interrupt masking.
Reported-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the maple bus to support asynchronous block reads
and writes as well as generally improving the quality of the code and
supporting concurrency (all needed to support the Dreamcast visual
memory unit - a driver will also be posted for that).
Changes in the bus driver necessitate some changes in the two maple bus
input drivers that are currently in mainline.
As well as supporting block reads and writes this code clean up removes
some poor handling of locks, uses an atomic status variable to serialise
access to devices and more robusly handles the general performance
problems of the bus.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SLAB_POISON is not a valid flag for kmem_create_cache() unless
CONFIG_DEBUG_SLAB is set, so remove it from the flags argument.
Acked-by: Adrian McMenamin <adrian@newgolddream.dyndns.info>
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The INTC code will be re-used across different architectures, so move
this out to drivers/sh/ and include/linux/sh_intc.h respectively.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We can simply wrap in to the dev_set/get_drvdata(), there's no reason
to track an extra level of private data on top of the struct device.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were completely inconsistent. Clean these up to take a maple_driver
pointer directly for consistency.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch cleans up the handling of the maple bus queue to remove
the risk of races when adding packets. It also removes references to the
redundant connect and disconnect functions.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The maple bus driver that went into the kernel mainline in September 2007
contained some bugs which were revealed by the update of the kobj code
for the current release series. Unfortunately those bugs also helped
ensure maple devices were properly detected. This patch (against the
current git) now ensures that devices are properly detected again.
(A previous attempt to fix this by delaying initialisation only partially
fixed this - as became apparent when the bus was fully loaded)
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve device detection for maple through longer delay
Experience suggests that a much longer delay in setting up the Maple bus
on the Dreamcast leads to better hardware detection.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Replacement second-in-series patch:
This patch fixes up memory leaks and, by delaying initialisation, makes
device detection more robust.
It also makes clearer the difference between struct maple_device and
struct device, as well as cleaning up the interrupt request code
(without changing its function in any way).
Also now removes redundant registration checking.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is fundamentally about fixing up the whitespace problems
introduced by my previous patch (that brought the code into mainline). A
second patch will follow that will fix memory leaks. The two need to be
applied sequentially.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The uevent API has changed from 2.6.22 and this patch eliminates
annoying compiler errors
Signed off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The Maple bus is SEGA's proprietary serial bus for peripherals
(keyboard, mouse, controller etc). The bus is capable of some
(limited) hotplugging and operates at up to 2 M/bits.
Drivers of one sort or another existed/exist for 2.4 and a rudimentary
port, which didn't support the 2.6 device driver model was also in
existence.
This driver - for the bus logic itself and for the keyboard (other
drivers will follow) are based on the code and concepts of those old
drivers but have lots of completely rewritten parts.
I have the maple bus code as a built in now as that seems the sane and
rational way to handle something like that - you either want the bus
or you don't.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This extends the API somewhat to allow for platform-specific VCR reading and
writing. Some platforms (like SH4-202) implement the VCR in a split VCRL and
VCRH, but end up being in reverse order or have other quirks that need to be
dealt with, so we add a set of superhyway_ops per-bus to accomodate this.
We also have to extend the per-device resources somewhat, as some devices now
conveniently split control and data blocks. So we allow a platform to
register its set of SuperHyway devices via superhyway_add_devices() with the
control block always ordered as the first resource (as this is the one that
userspace cares about).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
