Make sure the USB control request is allocated separately from
containing structure to prevent potential memory corruption on
non-cache-coherent systems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the reported device-type on big-endian machines is the same as
on little-endian ones.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB Embedded High-speed Host Electrical Test (EHSET) defines the
SINGLE_STEP_SET_FEATURE test as follows:
1) The host enumerates the test device with VID:0x1A0A, PID:0x0108
2) The host sends the SETUP stage of a GetDescriptor(Device)
3) The device ACKs the request
4) The host issues SOFs for 15 seconds allowing the test operator to
raise the scope trigger just above the SOF voltage level
5) The host sends the IN packet
6) The device sends data in response, triggering the scope
7) The host sends an ACK in response to the data
This patch adds additional handling to the EHCI hub driver and allows
the EHSET driver to initiate this test mode by issuing a a SetFeature
request to the root hub with a Test Selector value of 0x06. From there
it mimics ehci_urb_enqueue() but separately submits QTDs for the
SETUP and DATA/STATUS stages in order to insert a delay in between.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[jackp@codeaurora.org: imported from commit c2084930 on codeaurora.org;
minor cleanup and updated author email]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor so that register writes for configuration are only performed if
the device has a regmap provided and also register as a platform driver.
This allows the driver to be used to manage GPIO based control of the
device.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no software visible differences that I am aware of but in case
any are discovered allow the DTS to specify exactly which device is
present.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there is no runtime interface for changing modes this is probably
the most sensible default.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for supporting operation without an I2C control interface
factor out the I2C-specific parts of the probe routine from those that
don't do any register I/O.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will give access to the diagnostic infrastructure regmap has but
the main point is to support future refactoring.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the connect signal is pulled high then the device will start up meaning
that if we just pull it high on probe then the device will start running
prior to the configuration being written out. Fix this by pulling the GPIO
low when we reset and only pulling it high when configuration is finished.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The /RESET GPIO is not manipulated from atomic context so support GPIOs
that can't be written from atomic context by using _cansleep().
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intn and connect GPIO properties are swapped in the code which will
cause failures at runtime if these are connected, fix the code.
There are currently no in-tree users of this device to check or update.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies the interface presented by usb_get_status().
Instead of forcing callers to check for the proper data length and
convert the status value to host byte order, the function will now
do these things itself.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An Embedded Host High-Speed Electrical Test (EHSET) test fixture is
used to initiate test modes on a host controller in order to perform
the high speed electrical testing procedure for USB-IF compliance.
When this test fixture is connected to a host, it can enumerate as
one of several selectable VID/PID pairs, each corresponding to one
of the following test modes:
* TEST_SE0_NAK
* TEST_J
* TEST_K
* TEST_PACKET
* HS_HOST_PORT_SUSPEND_RESUME
* SINGLE_STEP_GET_DEV_DESC
* SINGLE_STEP_SET_FEATURE
The USB EHSET procedure can be found here:
http://www.usb.org/developers/onthego/EHSET_v1.01.pdf
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
[jackp@codeaurora.org: imported from commit 073c9409 on codeaurora.org;
minor cleanup and updated author email]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that no usb misc driver is looking for CONFIG_USB_DEBUG, or DEBUG,
don't enable it in the Makefile, as that's pointless.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we don't use the dbg() macro, remove it, and the module
parameter. Also fix up the "dump_data" function to properly use the
dynamic debug core and the correct printk options, and don't call it
twice per function, as the data doesn't change from the beginning and
the end of the call.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use a custom debug macro for just one driver, instead rely on the
in-kernel dynamic debugging logic, which can handle this much better.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unneeded tracing macros in this driver. The kernel has a
built-in trace function that can be used if this is really still needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the pr_* calls instead, which are much more descriptive.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we don't use the dbg() macro, remove it, and the module
parameter. Also fix up the "dump_data" function to properly use the
dynamic debug core and the correct printk options, and don't call it
twice per function, as the data doesn't change from the beginning and
the end of the call.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use a custom debug macro for just one driver, instead rely on the
in-kernel dynamic debugging logic, which can handle this much better.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unneeded tracing macros in this driver. The kernel has a
built-in trace function that can be used if this is really still needed.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to get rid of CONFIG_USB_DEBUG, so remove the reliance of the
ldusb driver on it. Don't use the custom macro, or a special module
parameter, instead, rely on the in-kernel dynamic debugging
infrastructure, which is much easier to use, and consistant across the
whole kernel.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull "exotic" arch fixes from Geert Uytterhoeven:
"This is a collection of several exotic architecture fixes, and a few
other fixes for issues that were detected while doing the former"
* 'exotic-arch-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (35 commits)
lib: Move fonts from drivers/video/console/ to lib/fonts/
console/font: Refactor font support code selection logic
Revert "staging/solo6x10: depend on CONFIG_FONTS"
input: cros_ec_keyb_clear_keyboard() depends on CONFIG_PM_SLEEP
score: Wire up asm-generic/xor.h
score: Remove unneeded <asm/dma-mapping.h>
openrisc: Wire up asm-generic/xor.h
h8300/boot: Use POSIX "$((..))" instead of bashism "$[...]"
h8300: Mark H83002 and H83048 CPU support broken
h8300: Switch h8300 to drivers/Kconfig
h8300: Limit timer channel ranges in Kconfig
h8300: Wire up asm-generic/xor.h
h8300: Fill the system call table using a CALL() macro
h8300: Fix <asm/tlb.h>
h8300: Hardcode symbol prefixes in asm sources
h8300: add missing definition for read_barries_depends()
frv: head.S - Remove commented-out initialization code
cris: Wire up asm-generic/vga.h
parport: disable PC-style parallel port support on cris
console: Disable VGA text console support on cris
...
Here is the big TTY / Serial driver merge for 3.11-rc1.
It's not all that big, nothing major changed in the tty api, which is a
nice change, just a number of serial driver fixes and updates and new
drivers, along with some n_tty fixes to help resolve some reported
issues.
All of these have been in the linux-next releases for a while, with the
exception of the last revert patch, which was reported this past weekend
by two different people as being needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHRtNIACgkQMUfUDdst+ymYgwCeKdyv9wRJ5cIWZt7Jz8ou3P/C
76YAoIvMv+fwoFBpyud/sC8eAKGTQ6KB
=Sjk6
-----END PGP SIGNATURE-----
Merge tag 'tty-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big TTY / Serial driver merge for 3.11-rc1.
It's not all that big, nothing major changed in the tty api, which is
a nice change, just a number of serial driver fixes and updates and
new drivers, along with some n_tty fixes to help resolve some reported
issues.
All of these have been in the linux-next releases for a while, with
the exception of the last revert patch, which was reported this past
weekend by two different people as being needed."
* tag 'tty-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (51 commits)
Revert "serial: 8250_pci: add support for another kind of NetMos Technology PCI 9835 Multi-I/O Controller"
pch_uart: Add uart_clk selection for the MinnowBoard
tty: atmel_serial: prepare clk before calling enable
tty: Reset itty for other pty
n_tty: Buffer work should not reschedule itself
n_tty: Fix unsafe update of available buffer space
n_tty: Untangle read completion variables
n_tty: Encapsulate minimum_to_wake within N_TTY
serial: omap: Fix device tree based PM runtime
serial: imx: Fix serial clock unbalance
serial/mpc52xx_uart: fix kernel panic when system reboot
serial: mfd: Add sysrq support
serial: imx: enable the clocks for console
tty: serial: add Freescale lpuart driver support
serial: imx: Improve Kconfig text
serial: imx: Allow module build
serial: imx: Fix warning when !CONFIG_SERIAL_IMX_CONSOLE
tty/serial/sirf: fix error propagation in sirfsoc_uart_probe()
serial: omap: fix potential NULL pointer dereference in serial_omap_runtime_suspend()
tty: serial: Enable uartlite for ARM zynq
...
The current Makefile rules to build font support are messy and buggy.
Replace them by Kconfig rules:
- Introduce CONFIG_FONT_SUPPORT, which controls the building of all font
code,
- Select CONFIG_FONT_SUPPORT for all drivers that use fonts,
- Select CONFIG_FONT_8x16 for all drivers that default to the VGA8x16
font,
- Drop the bogus console dependency for CONFIG_VIDEO_VIVI,
- Always process drivers/video/console/Makefile, as some drivers need
fonts even if CONFIG_VT is not set.
This fixes (if CONFIG_SOLO6X10=y and there are no built-in console
drivers):
drivers/built-in.o: In function `solo_osd_print':
drivers/staging/media/solo6x10/solo6x10-enc.c:144: undefined reference to `.find_font'
This fixes (if CONFIG_VT=n):
drivers/built-in.o: In function `vivi_init':
vivi.c:(.init.text+0x1a3da): undefined reference to `find_font'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com> [original part]
Acked-by: Randy Dunlap <rdunlap@infradead.org> [drivers/video/Makefile]
The usb3503 driver sleeps a flat 100ms when resetting the chip, with a
comment about waiting for the reference clock. This seems to be a
board-specific detail that should not hold up boot across all platforms.
This patch reduces the sleep to the 4ms initialization delay that the
chip itself actually requires (as per its data sheet). If certain boards
require more time to set up the reference clock, they should change this
through local patches or add a proper, configurable synchronization
mechanism.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove an erroneous tab that should be a space.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to add a property 'disabled-ports' representing the unused port
of USB3503. USB3503 can support up to 3 USB host port and each ports can be
controlled to be enabled or disabled. Do not describe this property if all
ports must be enabled.
You can represent the ports to disable in the device tree.
usb3503@08{
...
disabled-ports = <2 3>;
...
};
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to disable the USB ports unconnected to USB3503. In order to
disable the port, 'port_off_mask' must be set.
* Disable PORT1 only
.port_off_mask = USB3503_OFF_PORT1;
* Disable PORT1 and PORT3 only
.port_off_mask = USB3503_OFF_PORT1 | USB3503_OFF_PORT3;
* Enables all ports
.port_off_mask = 0;
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Impact:
1:convert all remain take_over_console to do_take_over_console
2:update take_over_console to do_take_over_console in comment
Commit dc9641895a ("vt: delete unneeded functions
register_con_driver|take_over_console") delete take_over_console,
but forget to convert remain take_over_console's users to new API
do_take_over_console, this patch fix it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed the assignment error in an if statement in adutux.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eliminated the error of whitespace needed after a closing brace
in adutux.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added space after comma in dbg() and usb_fill_int_urb() function
calls in adutux.c to meet kernel coding standards.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replaced asm/uaccess.h with linux/uaccess.h in adutux.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
This patch removes the depends on USB from all config symbols in
drivers/usb/host/Kconfig and replace that with an if USB / endif block
as suggested by Alan Stern. Some source ... Kconfig lines have been
shuffled around to permit a better regroupment of the Kconfig files
depending on "config USB" item. No functionnal change is introduced.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the Apple 24" LED Cinema display to the supported devices.
Signed-off-by: Ben Jencks <ben@bjencks.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A failed kzalloc() is reported with a dev_err that dereferences the null
sisusb, this will cause a NULL pointer deference error.
Instead, pass dev->dev to the dev_err() rather than &sisusb->sisusb_dev->dev
Smatch analysis:
drivers/usb/misc/sisusbvga/sisusb.c:3087 sisusb_probe() error: potential null
dereference 'sisusb'. (kzalloc returns null)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbtest driver includes some rather simple-minded logic for
selecting an altsetting to test. It doesn't work well for the g_zero
gadget, because it selects altsetting 0 (which doesn't have
isochronous endpoints) rather than altsetting 1 (which does have them,
if the gadget's hardware supports them). This prevents usbtest's
isochronous tests (15, 16, 22, and 23) from working with g_zero.
Since g_zero is one of the most common gadget drivers used for USB
testing, usbtest should do a better job of supporting it. But since
some programs may rely on the current scheme for selecting
altsettings, I didn't want to change it.
Instead, this patch (as1655) adds a module parameter to usbtest, which
can be used to override the default altsetting. Since usbtest is
never used by normal users (most distributions probably don't even
build it), the new module parameter won't inconvenience anybody. In
any case, it is entirely optional -- leaving it unset preserves the
existing behavior.
The patch also fixes a related bug in usbtest: After selecting an
altsetting, the driver neglects to store its selection.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the compiler warning of uninitialized variable.
drivers/usb/misc/usb3503.c: In function ‘usb3503_probe’:
drivers/usb/misc/usb3503.c:215:13: warning: ‘mode’ may be used uninitialized
in this function [-Wuninitialized]
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added device tree support for usb3503 driver and add new document with device tree binding information.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the warning,
6a099c6365 [4/10] USB: misc: Add USB3503 High-Speed Hub Controller
drivers/usb/misc/usb3503.c:238 usb3503_probe() error: we previously assumed 'pdata' could be null (see line 196)
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds new driver of SMSC USB3503 USB 2.0 hub controller with HSIC
upstream connectivity and three USB 2.0 downstream ports. The specification
can be found from 'http://www.smsc.com/index.php?tid=295&pid=325'.
The current version have been tested very basic features switching the modes,
HUB-MODE and STANDBY-MODE.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1639) fixes a minor bug in the usbtest driver. Due to
concurrent changes, a test originally written as number 17 got changed
to number 24, but the corresponding change was not made in the log
message. This updates the log message.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an error during modpost, when ezusb is built into the kernel
while USB is built as module.
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Cc: stable <stable@vger.kernel.org>
--
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If param->length is zero, then this could lead to a divide by zero bug
later in the function when we do: size %= max;
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since commit b4036cc (usb: gadget: add
isochronous support to gadget zero), g_zero
has learned about isochronous transfers, which
allows us to use usbtest.ko to exercise
isochronous pipes.
All we need to do to enable that functionality
on usbtest.ko, is set the "iso" to 1 on
struct usbtest_info
Signed-off-by: Boyan Nedeltchev <boyan@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pulls in all of the USB changes in 3.7-rc3 into usb-next and
resolves the merge issue with:
drivers/usb/misc/ezusb.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ezusb code was split out, support was added for the fx2 chip
type, but no one is using these functions, so comment it out. If
someone needs it, it can be added back in the future.
Also properly include <linux/usb/ezusb.h> into the ezusb.c file, to
ensure we catch any function prototype mis-matches
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch
- moves drivers/usb/serial/ezusb.c to drivers/usb/misc/
- renamed CONFIG_USB_EZUSB to CONFIG_USB_EZUSB_FX2 to avoid build errors
- adapts Makefiles and Kconfigs switching from bool to tristate for CONFIG_USB_EZUSB_FX2
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"udev" can't be NULL here. The debugging printk() makes static checkers
complain when we dereference it later in the function inside the call to
usb_rcvctrlpipe().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Zack Parsons <k3bacon@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bMaxPacketSize0 field for super speed is a power of 2, not a count.
The size itself is always 512.
Max packet size for a super speed bulk endpoint is 1024, so
allocate the urb size in halt_simple() accordingly.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the conflict in:
drivers/usb/host/ehci-fsl.c
And picks up loads of xhci bugfixes to make it easier for others to test
with.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Zack Parsons <k3bacon@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Juergen Stuber <starblue@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Michael Hund <mhund@ld-didactic.de>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current probing code is setting URB_NO_TRANSFER_DMA_MAP flag into a wrong urb
structure, and this causes BUG_ON with some USB host implementations.
This patch fixes the issue.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes allocation of coherent buffer for the control-request setup-packet
buffer from the yurex driver. Using coherent buffers for setup-packet is
obsolete and does not work with some USB host implementations.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Free the two previously allocated buffers before exiting the function in an
error case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A large `nents' from userspace could overflow the allocation size,
leading to memory corruption.
| alloc_sglist()
| usbtest_ioctl()
Use kmalloc_array() to avoid the overflow.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid overflowing context.count = param->sglen * param->iterations,
where both `sglen' and `iterations' are from userspace.
| test_ctrl_queue()
| usbtest_ioctl()
Keep -EOPNOTSUPP for error code.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This changes the max length for the usb seven segment delcom device to 8
from 6. Delcom has both 6 and 8 variants and having 8 works fine with
devices which are only 6.
Signed-off-by: Harrison Metzger <harrisonmetz@gmail.com>
Signed-off-by: Stuart Pook <stuart@acm.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/misc/emi26.c:40: warning: 'emi26_init' declared 'static' but never defined
drivers/usb/misc/emi26.c:41: warning: 'emi26_exit' declared 'static' but never defined
drivers/usb/misc/emi62.c:49: warning: 'emi62_init' declared 'static' but never defined
drivers/usb/misc/emi62.c:50: warning: 'emi62_exit' declared 'static' but never defined
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
hid-input/battery: add FEATURE quirk
hid-input/battery: remove battery_val
hid-input/battery: power-supply type really *is* a battery
hid-input/battery: make the battery setup common for INPUTs and FEATUREs
hid-input/battery: deal with both FEATURE and INPUT report batteries
hid-input/battery: add quirks for battery
hid-input/battery: remove apparently redundant kmalloc
hid-input: add support for HID devices reporting Battery Strength
HID: hid-multitouch: add support 9 new Xiroku devices
HID: multitouch: add support for 3M 32"
HID: multitouch: add support of Atmel multitouch panels
HID: usbhid: defer LED setting to a workqueue
HID: usbhid: hid-core: submit queued urbs before suspend
HID: usbhid: remove LED_ON
HID: emsff: use symbolic name instead of hardcoded PID constant
HID: Enable HID_QUIRK_MULTI_INPUT for Trio Linker Plus II
HID: Kconfig: fix syntax
HID: introduce proper dependency of HID_BATTERY on POWER_SUPPLY
HID: multitouch: support PixArt optical touch screen
HID: make parser more verbose about parsing errors by default
...
Fix up rename/delete conflict in drivers/hid/hid-hyperv.c (removed in
staging, moved in this branch) and similarly for the rules for same file
in drivers/staging/hv/{Kconfig,Makefile}.
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
both callers of device_get_devnode() are only interested in lower 16bits
and nobody tries to return anything wider than 16bit anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We were sending data on the stack when uploading firmware, which causes
some machines fits, and is not allowed. Fix this by using the buffer we
already had around for this very purpose.
Reported-by: Wouter M. Koolen <wmkoolen@cwi.nl>
Tested-by: Wouter M. Koolen <wmkoolen@cwi.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the drivers in drivers/usb/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Simon Arlott <cxacru@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Cc: Cesar Miquel <miquel@df.uba.ar>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Michael Hund <mhund@ld-didactic.de>
Cc: Zack Parsons <k3bacon@gmail.com>
Cc: Melchior FRANZ <mfranz@aon.at>
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In a few places in the kernel, the code prints
a human-readable USB device speed (eg. "high speed").
This involves a switch statement sometimes wrapped
around in ({ ... }) block leading to code repetition.
To mitigate this issue, this commit introduces
usb_speed_string() function, which returns
a human-readable name of provided speed.
It also changes a few places switch was used to use
this new function. This changes a bit the way the
speed is printed in few instances at the same time
standardising it.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size
instead of le16_to_cpu(desc->wMaxPacketSize).
This patch fix it up
Cc: Armin Fuerst <fuerst@in.tum.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Erdfelt <johannes@erdfelt.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: David Kubicek <dave@awk.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Brad Hards <bhards@bigpond.net.au>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: David Lopo <dlopo@chipidea.mips.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Xie Xiaobo <X.Xie@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Jiang Bo <tanya.jiang@freescale.com>
Cc: Yuan-hsin Chen <yhchen@faraday-tech.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Roman Weissgaerber <weissg@vienna.at>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Florian Floe Echtler <echtler@fs.tum.de>
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Juergen Stuber <starblue@sourceforge.net>
Cc: Georges Toth <g.toth@e-biz.lu>
Cc: Bill Ryder <bryder@sgi.com>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Executing
| testusb -a -c 1 -t 3 -v 421 -s 2048
does not complete on the gadget side.
g_zero enqueues a 4096 bytes long buffer. The host sends 2048bytes which
is a multiple of wMaxPacketSize (either 64 or 512 bytes). The host is
done with sending data but the gadget waits for more.
Since the protocol does not include transfer-length-field sending a
terminating zero packet seems the only way out.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
On amd64 unsigned is not as wide as pointer and this causes a compiler
warning. Switching to unsigned long corrects the problem.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added several new devices to ldusb and excluded them from the HID driver.
Signed-off-by: Michael Hund <mhund@ld-didactic.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1452b) adds a new test case to the usbtest driver. Test
24 exercises the unlink-from-queue pathways in the host. It queues a
user-specified number of bulk-OUT URBs of user-specified size, unlinks
the fourth- and second-from-last URBs in the queue, and then waits to
see if all the URBs complete in the expected way (except of course
that the unlinked URBs might complete normally, if they weren't
unlinked soon enough).
This new test has confirmed the existence of a bug in the ehci-hcd
driver, to be fixed by a separate patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My testprog do a lot of bitbang - after hours i got following warning and my machine lockups:
WARNING: at /build/buildd/linux-2.6.38/lib/kref.c:34
After debugging uss720 driver i discovered that the completion callback was called before
usb_submit_urb returns. The callback frees the request structure that is krefed on return by
usb_submit_urb.
Signed-off-by: Peter Holik <peter@holik.at>
Acked-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There may be multiple ways of controlling the backlight on a given
machine. Allow drivers to expose the type of interface they are
providing, making it possible for userspace to make appropriate policy
decisions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a set of new tests similar to the existing ones but using
transfer buffers at an "odd" address [ie offset of +1 from
the buffer obtained by kmalloc() or usb_alloc_coherent()]
The new tests are:
#17 : bulk out (like #1) using kmalloc and DMA mapping by USB core.
#18 : bulk in (like #2) using kmalloc and DMA mapping by USB core.
#19 : bulk out (like #1) using usb_alloc_coherent()
#20 : bulk in (like #2) using usb_alloc_coherent()
#21 : control write (like #14)
#22 : isochonous out (like #15)
#23 : isochonous in (like #16)
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit ecc1624a2f (USB: misc: uss720.c: add
another vendor/product ID) duplicated entry in the driver's USB device ID
table. Remove the duplicate.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If case of an unknown usb_device_id->driver_info (which could only
occur if the info got corrupted somewhere outside the usbled driver),
a debug message depended on an uninitialized value. This was harmless,
but ugly, and gets fixed with this patch.
Signed-off-by: Melchior FRANZ <mfranz@aon.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
So far the USBLED driver only supports Delcom's "USB Visual Signal
Indicator" (http://www.delcomproducts.com/products_USBLMP.asp). The
driver generates virtual files "red", "green", and "blue" under the
device's /sys/ directory, where color values can be read from and
written to.
This patch adds support for Dream Cheeky's "DL100B Webmail Notifier"
(http://www.dreamcheeky.com/webmail-notifier -- available from several
shops, such as http://www.conrad.at/ce/de/product/777048/USB-WEBMAIL).
This device isn't as pretty as Delcom's, but it's *far* cheaper, and
its 3 LEDs can be set in 32 brightness steps each. The grey envelope
contour can easily be removed, leaving a rather neutral white box (with
a few small holes), which is useful for generic signalling purposes.
Of course, the small circuit board can easily be put into a prettier
case.
The DL100B device pretends to be a HID, but the HID descriptor shows
that it's not overly useful as such (see below). The patch therefore
removes the "HID-ness" (hid-core.c, hid-ids.h), and adds the necessary
commands to usbled.c. The protocol info comes from the developer's
manual that Dream Cheeky kindly provided (815DeveloperManual.pdf).
HID descriptor:
0: 05 01 Usage Page 'Generic Desktop Controls'
2: 09 10 Usage 'Reserved'
4: a1 01 Collection 'Application (mouse, keyboard)'
6: 05 00 Usage Page 'Undefined'
8: 19 10 Usage Minimum = 16
10: 29 11 Usage Maximum = 17
12: 15 00 Logical Minimum = 0
14: 25 0f Logical Maximum = 15
16: 75 08 Report Size = 8
18: 95 08 Report Count = 8
20: 91 02 Output data *var abs lin pref-state null-pos non-vol bit-field
22: 19 10 Usage Minimum = 16
24: 29 11 Usage Maximum = 17
26: 15 00 Logical Minimum = 0
28: 25 0f Logical Maximum = 15
30: 75 08 Report Size = 8
32: 95 08 Report Count = 8
34: 81 00 Input data array abs lin pref-state null-pos non-vol bit-field
36: c0 End Collection
Signed-off-by: Melchior FRANZ <mfranz@aon.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fabio Battaglia report that he has another cable that works with this
driver, so this patch adds its vendor/product ID.
Signed-off-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Default llseek operation behavior was changed by the patch named
"vfs: make no_llseek the default" after the yurex driver had been merged,
so the llseek to yurex is now ignored.
This patch add llseek fop with default_llseek to yurex driver
to catch up to the change.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They should not be writable by any user.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Harrison Metzger <harrisonmetz@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They should not be writable by any user.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It should not be writable by any user.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Sam Hocevar <sam@zoy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They should not be writable by any user.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oliver Bock <bock@tfh-berlin.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Structure iowarrior_info is copied to userland with padding byted
between "serial" and "revision" fields uninitialized. It leads to
leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: stable <stable@kernel.org>
Acked-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Structure sisusb_info is copied to userland with "sisusb_reserved" field
uninitialized. It leads to leaking of contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
If the iowarrior devices in this case statement support more than 8 bytes
per report, it is possible to write past the end of a kernel heap allocation.
This will probably never be possible, but change the allocation to be more
defensive anyway.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For all modules, change <module>-objs to <module>-y; remove
if-statements and replace with lists using the kbuild idiom; move
flags to the top of the file; and fix alignment while trying to
maintain the original scheme in each file.
None of the dependencies are modified.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check the data length of isochronous transfers is
as expected.
With this test #16 will now fail if the device side
sends no data.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the memory leak on disconnecting the device.
In addition, it fixes some messages corrupted by incorrect encoding.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This assigns the minor number 192 to the yurex driver.
We also fix up the previous usb minor number entry, it was wrong.
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Meywa-Denki/Kayac YUREX is a leg-shakes sensor device.
See http://bbu.kayac.com/en/about/ for further information.
This driver support read/write the leg-shakes counter in the device
via a device file /dev/yurex[0-9]*.
[minor coding style cleanups fixed by gregkh]
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "mutex" ftdi->sw_lock is used as a lock and a completion. Convert
it to a real semaphore which allows both.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
copy_to_user() returns number of not copied bytes, not error code.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
copy_to_user() returns number of not copied bytes, not error code.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is very common that one altsetting may include only one iso-in or iso-out
single endpoint, especially for high bandwidth endpoint, so support it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And audit all the users. None needed the BKL. That was easy
because there was only very few around.
Tested with allmodconfig build on x86-64
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
From: Andi Kleen <ak@linux.intel.com>
Greg prefers this to go through the trivial tree.
http://lkml.org/lkml/2010/6/24/1
There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.
Standardize them a bit.
Moved a statement down a line in drivers/usb/host/u132-hcd.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Super speed is also fast enough to let sisusbvga operate.
Therefor expand the checks.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL is not needed here because necessary locking is already provided
by mutex sisusb->lock.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1350) removes all usages of coherent buffers for USB
control-request setup-packet buffers. There's no good reason to
reserve coherent memory for these things; control requests are hardly
ever used in large quantity (the major exception is firmware
transfers, and they aren't time-critical). Furthermore, only seven
drivers used it. We might as well always use streaming DMA mappings
for setup-packet buffers, and remove some extra complexity from
usbcore.
The DMA-mapping portion of hcd.c is currently in flux. A separate
patch will be submitted to remove support for URB_NO_SETUP_DMA_MAP
after everything else settles down. The removal should go smoothly,
as by then nobody will be using it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Seems to me that BKL is not needed here because necessary locking is already
provided by mutex sisusb->lock.
Also change the returned value to long.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug with the usbsevseg driver which assumed that USB
autosuspend will always be used.
Signed-off-by: Harrison Metzger <harrisonmetz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Values such as max_brightness should be set before backlights are
registered, but the current API doesn't allow that. Add a parameter to
backlight_device_register and update drivers to ensure that they
set this correctly.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
On error while registering backlight, return it to caller instead of
returning 0.
Mark struct backlight_ops as const.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a driver can wait on an event, it can also use GFP_KERNEL.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the vstusb driver and support from the Linux tree.
This driver provided support for Vernier Software & Technology devices
and spectrometers (Ocean Optics). This driver is being replaced by a
user space - libusb - implementation.
Signed-off-by: Jim Collar <jim.collar@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduces string space a bit
Neaten a macro redefine of dbg
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Barry project's userspace program, bcharge, can better handle this
device and functionality, and it also works with the latest phones,
which this driver does not support. So remove it, as the userspace code
should be used instead.
Cc: Chris Frey <cdfrey@foursquare.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL was not needed at all. Removed without replacement.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver had used BKL to guard against disconnect but
was incorrectly converted leaving an SMP race.
BKL was added to disconnect() to fix this race
BKL was removed from ioctl() as the mutex is sufficient
on its own.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1329) converts the USB stack over to the PM core's
runtime PM framework. This involves numerous changes throughout
usbcore, especially to hub.c and driver.c. Perhaps the most notable
change is that CONFIG_USB_SUSPEND now depends on CONFIG_PM_RUNTIME
instead of CONFIG_PM.
Several fields in the usb_device and usb_interface structures are no
longer needed. Some code which used to depend on CONFIG_USB_PM now
depends on CONFIG_USB_SUSPEND (requiring some rearrangement of header
files).
The only visible change in behavior should be that following a system
sleep (resume from RAM or resume from hibernation), autosuspended USB
devices will be resumed just like everything else. They won't remain
suspended. But if they aren't in use then they will naturally
autosuspend again in a few seconds.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the USB product ID of KAIREN's USB VGA Adaptor,
USB20SVGA-MB-PLUS, to sisusbvga work with it.
Signed-off-by: Tanaka Akira <akr@fsij.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
brightness status is reported by the Apple Cinema Displays as an
'unsigned char' (u8) value, but the code used 'char' instead.
Note that he driver was developed on the PowerPC architecture,
where the two types are synonymous, which is not always the case.
Fixed that. Otherwise the driver will interpret brightness
levels > 127 as negative, and fail to load.
Signed-off-by: pancho horrillo <pancho@pancho.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While converting emi62 to use request_firmware(), the driver was also
changed to use the ihex helper functions. However, this broke the loading
of the FPGA firmware because the code tries to access the addr field of
the EOF record which works with a plain array that has an empty last
record but not with the ihex helper functions where the end of the data is
signaled with a NULL record pointer, resulting in:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<f80d248c>] emi62_load_firmware+0x33c/0x740 [emi62]
This can be fixed by changing the loop condition to test the return value
of ihex_next_binrec() directly (like in emi26.c).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Der Mickster <retroeffective@gmail.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow module_param to be writeable. This allows us to change
the parameter if usbtest is built-in in the kernel.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found a memory leak in lcd_probe. Instead of returning without
releasing the memory, jump to the error label which frees it.
http://stanse.fi.muni.cz/
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* remove asm/atomic.h inclusion from kref.h -- not needed, linux/types.h
is enough for atomic_t
* remove linux/kref.h inclusion from files which do not need it.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds to the usbsevseg driver:
- suspend/resume support
- reset_resume support
- autosuspend using the display's power state to determine idleness
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Harrison Metzger <harrisonmetz@gmail.com>
usb: full runtime PM support for idmouse driver
- add suspend/resume support
- add reset_resume support
- add support for autosuspend
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-by: Andreas Deresch <aderesch@fs.tum.de>
poll() should test for a disconnection of the device.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
poll needs to return an error if a device is disconnected
- make poll check for device's presence
- wake all waiters in disconnect
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch falls out of my work to fix usbmon so it uses virtual addresses.
It is not necessary, the "new" usbmon should work just fine with sisusbvga.
However, it seems ridiculous that anyone would use uncached memory to
transfer bulk data. Dropping the unnecessary use of usb_buffer_alloc
should be beneficial here, in case anyone ever uses the dongle on
anything beyond x86.
I had no success in raising the author of the driver by e-mail, so
the patch is not actually tested.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
