The driver was using its struct usb_interface pointer as an inverted
disconnected flag and was setting it to NULL before making sure all
completion handlers had run. This could lead to NULL-pointer
dereferences in the dev_err() statements in the completion handlers
which relies on said pointer.
Fix this by using a dedicated disconnected flag.
Note that this is also addresses a NULL-pointer dereference at release()
and a struct usb_interface reference leak introduced by a recent runtime
PM fix, which depends on and should have been submitted together with
this patch.
Fixes: 4212cd74ca ("USB: usb-skeleton.c: remove err() usage")
Fixes: 5c290a5e42 ("USB: usb-skeleton: fix runtime PM after driver unbind")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191009170944.30057-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch fixes issue with Halt Endnpoint Test observed during using g_zero
driver as DUT. Bug occurred only on some testing board.
Endpoint can defer transition to Halted state if endpoint has pending
requests.
Patch add additional condition that allows to return correct endpoint
status during Get Endpoint Status request even if the halting endpoint
is in progress.
Reported-by: Rahul Kumar <kurahul@cadence.com>
Signed-off-by: Rahul Kumar <kurahul@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Tested-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/1570430355-26118-1-git-send-email-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()"), platform_get_irq() will call dev_err() itself on
failure, so there is no need for the driver to also do this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191005210449.3926-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3 code to get the "peripheral" / "host" / "otg" IRQ first tries
platform_get_irq_byname() and then falls back to the IRQ at index 0 if
the platform_get_irq_byname().
In this case we do not want platform_get_irq_byname() to print an error
on failure, so switch to platform_get_irq_byname_optional() instead which
does not print an error.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205037
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191005210449.3926-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers (e.g dwc3) first try to get an IRQ byname and then fall
back to the one at index 0. In this case we do not want the error(s)
printed by platform_get_irq_byname(). This commit adds a new
platform_get_irq_byname_optional(), which does not print errors, for this.
While at it also improve the kdoc text for platform_get_irq_byname() a bit.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205037
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20191005210449.3926-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a long-standing issue in the keyspan driver which could
lead to NULL-pointer dereferences when a device had unexpected endpoint
descriptors.
Included are also some new device IDs.
All but the last two commits have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXZdOEwAKCRALxc3C7H1l
CMe6AP44mJLEAJ9ODG9F+W3vekbuHitipeBpxYkSQEtC8Cfv1AD+J/lp1/4kHEoE
B3MbYseu0PtrqmFGrIkQJEAR/CJcrAQ=
=7w1Y
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.4-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.4-rc2
Here's a fix for a long-standing issue in the keyspan driver which could
lead to NULL-pointer dereferences when a device had unexpected endpoint
descriptors.
Included are also some new device IDs.
All but the last two commits have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.4-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: keyspan: fix NULL-derefs on open() and write()
USB: serial: option: add support for Cinterion CLS8 devices
USB: serial: option: add Telit FN980 compositions
USB: serial: ftdi_sio: add device IDs for Sienna and Echelon PL-20
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Note that runtime PM has never actually been enabled for this driver
since the support_autosuspend flag in its usb_driver struct is not set.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the original bindings that were superseeded by the YAML schemas
didn't mention that phy-names was needed, it turns out that phy-names is
required if phys is set according to phy/phy-bindings.txt.
Let's add back those properties.
Fixes: 14ec072a19 ("dt-bindings: usb: Convert USB HCD generic binding to YAML")
Fixes: c93bcace10 ("dt-bindings: usb: Convert the generic OHCI binding to YAML")
Fixes: c3e2485d5f ("dt-bindings: usb: Convert the generic EHCI binding to YAML")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-2-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commits 3d109bdca9 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6d ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca9 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6d ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to usb_ep_set_halt()'s description,
__usbhsg_ep_set_halt_wedge() should return -EAGAIN if the IN endpoint
has any queue or data. Otherwise, this driver is possible to cause
just STALL without sending a short packet data on g_mass_storage driver,
and then a few resetting a device happens on a host side during
a usb enumaration.
Fixes: 2f98382dcd ("usb: renesas_usbhs: Add Renesas USBHS Gadget")
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1569924633-322-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 97664a207b ("usb: renesas_usbhs: shrink spin lock area")
had added a usbhsg_pipe_disable() calling into
__usbhsg_ep_set_halt_wedge() accidentally. But, this driver should
not call the usbhsg_pipe_disable() because the function discards
all queues. So, this patch removes it.
Fixes: 97664a207b ("usb: renesas_usbhs: shrink spin lock area")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1569924633-322-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc points out a suspicious cast from a pointer to an 'int' when
compile-testing on 64-bit architectures.
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_pop_fifo’:
drivers/usb/gadget/udc/lpc32xx_udc.c:1156:11: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_stuff_fifo’:
drivers/usb/gadget/udc/lpc32xx_udc.c:1257:11: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
The code works find, but it's easy enough to change the cast to
a uintptr_t to shut up that warning.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190918200201.2292008-1-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udev stored in ep->hcpriv might be NULL if tt buffer is cleared
due to a halted control endpoint during device enumeration
xhci_clear_tt_buffer_complete is called by hub_tt_work() once it's
scheduled, and by then usb core might have freed and allocated a
new udev for the next enumeration attempt.
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Reported-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-9-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit f7fac17ca9 ("xhci: Convert xhci_handshake() to use
readl_poll_timeout_atomic()"), ASMedia xHCI may fail to suspend.
Although the algorithms are essentially the same, the old max timeout is
(usec + usec * time of doing readl()), and the new max timeout is just
usec, which is much less than the old one.
Increase the timeout to make ASMedia xHCI able to suspend again.
BugLink: https://bugs.launchpad.net/bugs/1844021
Fixes: f7fac17ca9 ("xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()")
Cc: <stable@vger.kernel.org> # v5.2+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-8-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system can hit a deadlock if an xhci adapter breaks while initializing.
The deadlock is between two threads: thread 1 is tearing down the
adapter and is stuck in usb_unlocked_disable_lpm waiting to lock the
hcd->handwidth_mutex. Thread 2 is holding this mutex (while still trying
to add a usb device), but is stuck in xhci_endpoint_reset waiting for a
stop or config command to complete. A reboot is required to resolve.
It turns out when calling xhci_queue_stop_endpoint and
xhci_queue_configure_endpoint in xhci_endpoint_reset, the return code is
not checked for errors. If the timing is right and the adapter dies just
before either of these commands get issued, we hang indefinitely waiting
for a completion on a command that didn't get issued.
This wasn't a problem before the following fix because we didn't send
commands in xhci_endpoint_reset:
commit f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
With the patch I am submitting, a duration test which breaks adapters
during initialization (and which deadlocks with the standard kernel) runs
without issue.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Torez Smith <torez@redhat.com>
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Signed-off-by: Torez Smith <torez@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-7-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA 3.1 xHCI card would lose power when moving power state into D3Cold.
Thus we need to wait for CNR bit to clear in xhci resume, just as in
xhci init.
[Minor changes to comment and commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Rick Tseng <rtseng@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-6-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Early xHCI 1.1 spec did not mention USB 3.1 capable hosts should set
sbrn to 0x31, or that the minor revision is a two digit BCD
containing minor and sub-minor numbers.
This was later clarified in xHCI 1.2.
Some USB 3.1 capable hosts therefore have sbrn set to 0x30, or minor
revision set to 0x1 instead of 0x10.
Detect the USB 3.1 capability correctly for these hosts as well
Fixes: ddd57980a0 ("xhci: detect USB 3.2 capable host controllers correctly")
Cc: <stable@vger.kernel.org> # v4.18+
Cc: Loïc Yhuel <loic.yhuel@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-5-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an endpoint is encountered that returns USB3_LPM_DEVICE_INITIATED, keep
checking further endpoints, as there might be periodic endpoints later
that return USB3_LPM_DISABLED due to shorter service intervals.
Without this, the code can set too high a maximum-exit-latency and
prevent the use of multiple USB3 cameras that should be able to work.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Schmidt <jan@centricular.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If host/hub initiated link pm is prevented by a driver flag we still must
ensure that periodic endpoints have longer service intervals than link pm
exit latency before allowing device initiated link pm.
Fix this by continue walking and checking endpoint service interval if
xhci_get_timeout_no_hub_lpm() returns anything else than USB3_LPM_DISABLED
While at it fix the split line error message
Tested-by: Jan Schmidt <jan@centricular.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check printing out the "WARN Wrong bounce buffer write length:"
uses incorrect values when comparing bytes written from scatterlist
to bounce buffer. Actual copied lengths are fine.
The used seg->bounce_len will be set to equal new_buf_len a few lines later
in the code, but is incorrect when doing the comparison.
The patch which added this false warning was backported to 4.8+ kernels
so this should be backported as far as well.
Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 597c56e372 ("xhci: update bounce buffer with correct sg num")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver would return with a nonzero open count in case the reset
control request failed. This would prevent any further attempts to open
the char dev until the device was disconnected.
Fix this by incrementing the open count only on successful open.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is using its struct usb_device pointer as an inverted
disconnected flag, but was setting it to NULL before making sure all
completion handlers had run. This could lead to a NULL-pointer
dereference in a number of dev_dbg and dev_err statements in the
completion handlers which relies on said pointer.
Fix this by unconditionally stopping all I/O and preventing
resubmissions by poisoning the interrupt URBs at disconnect and using a
dedicated disconnected flag.
This also makes sure that all I/O has completed by the time the
disconnect callback returns.
Fixes: 9d974b2a06 ("USB: legousbtower.c: remove err() usage")
Fixes: fef526cae7 ("USB: legousbtower: remove custom debug macro")
Fixes: 4dae996380 ("USB: legotower: remove custom debug macro and module parameter")
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a potential deadlock if disconnect races with open.
Since commit d4ead16f50 ("USB: prevent char device open/deregister
race") core holds an rw-semaphore while open is called and when
releasing the minor number during deregistration. This can lead to an
ABBA deadlock if a driver takes a lock in open which it also holds
during deregistration.
This effectively reverts commit 78663ecc34 ("USB: disconnect open race
in legousbtower") which needlessly introduced this issue after a generic
fix for this race had been added to core by commit d4ead16f50 ("USB:
prevent char device open/deregister race").
Fixes: 78663ecc34 ("USB: disconnect open race in legousbtower")
Cc: stable <stable@vger.kernel.org> # 2.6.24
Reported-by: syzbot+f9549f5ee8a5416f0b95@syzkaller.appspotmail.com
Tested-by: syzbot+f9549f5ee8a5416f0b95@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check for short transfers when retrieving the version
information at probe to avoid leaking uninitialised slab data when
logging it.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Making sure that ucsi_displayport_enter() function does not
return an error if the displayport alternate mode has
already been entered. It's normal that the firmware (or
controller) has already entered the alternate mode by the
time the operating system is notified about the device.
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191004100219.71152-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "run_isr" flag is used for preventing the driver from
calling the interrupt service routine in its runtime resume
callback when the driver is expecting completion to a
command, but what that basically does is that it hides the
real problem. The real problem is that the controller is
allowed to suspend in the middle of command execution.
As a more appropriate fix for the problem, using autosuspend
delay time that matches UCSI_TIMEOUT_MS (5s). That prevents
the controller from suspending while still in the middle of
executing a command.
This fixes a potential deadlock. Both ccg_read() and
ccg_write() are called with the mutex already taken at least
from ccg_send_command(). In ccg_read() and ccg_write, the
mutex is only acquired so that run_isr flag can be set.
Fixes: f0e4cd948b ("usb: typec: ucsi: ccg: add runtime pm workaround")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191004100219.71152-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the redundant lcd mutex introduced by commit 925ce689bb ("USB:
autoconvert trivial BKL users to private mutex") which replaced an
earlier BKL use.
The lock serialised calls to open() against other open() and a custom
ioctl() returning the bcdDevice (sic!), but neither is needed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190926091228.24634-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the redundant disconnect mutex which was introduced after the
open-disconnect race had been addressed generally in USB core by commit
d4ead16f50 ("USB: prevent char device open/deregister race").
Specifically, the rw-semaphore in core guarantees that all calls to
open() will have completed and that no new calls to open() will occur
after usb_deregister_dev() returns. Hence there is no need use the
driver data as an inverted disconnected flag.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190926091228.24634-8-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to stop all I/O on disconnect by adding a disconnected flag
which is used to prevent new I/O from being started and by stopping all
ongoing I/O before returning.
This also fixes a potential use-after-free on driver unbind in case the
driver data is freed before the completion handler has run.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 7bbe990c98
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190926091228.24634-7-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those files got renamed, but another DT file still points to the older
places.
Fixes: 87a55485f2 ("dt-bindings: phy: meson-g12a-usb3-pcie-phy: convert to yaml")
Fixes: da86d286cc ("dt-bindings: phy: meson-g12a-usb2-phy: convert to yaml")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/9ca2d136a1f79c878fff1208f9b536b0b613c0d5.1569330078.git.mchehab+samsung@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "port->typec_caps.data" and "port->typec_caps.type" variables are
enums and in this context GCC will treat them as an unsigned int so they
can never be less than zero.
Fixes: ae8a2ca8a2 ("usb: typec: Group all TCPCI/TCPM code together")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191001120117.GA23528@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The power budget for SuperSpeed mode should be 900 mA
according to USB specification, so set the power budget
to 900mA for dummy_start_ss which is only used for
SuperSpeed mode.
If the max power consumption of SuperSpeed device is
larger than 500 mA, insufficient available bus power
error happens in usb_choose_configuration function
when the device connects to dummy hcd.
Signed-off-by: Jacky Cao <Jacky.Cao@sony.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/16EA1F625E922C43B00B9D82250220500871CDE5@APYOKXMS108.ap.sony.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the return value of vhci_init_attr_group and
sysfs_create_group is non-zero, which mean they failed
to init attr_group and create sysfs group, so it would
better add 'failed' message to indicate that.
This patch also change pr_err to dev_err to trace which
device is failed.
Fixes: 0775a9cbc6 ("usbip: vhci extension: modifications to vhci driver")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190916150921.152977-1-maowenan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Greg KH, it has been generally agreed that when a USB
driver encounters an unknown error (or one it can't handle directly),
it should just give up instead of going into a potentially infinite
retry loop.
The three codes -EPROTO, -EILSEQ, and -ETIME fall into this category.
They can be caused by bus errors such as packet loss or corruption,
attempting to communicate with a disconnected device, or by malicious
firmware. Nowadays the extent of packet loss or corruption is
negligible, so it should be safe for a driver to give up whenever one
of these errors occurs.
Although the yurex driver handles -EILSEQ errors in this way, it
doesn't do the same for -EPROTO (as discovered by the syzbot fuzzer)
or other unrecognized errors. This patch adjusts the driver so that
it doesn't log an error message for -EPROTO or -ETIME, and it doesn't
retry after any errors.
Reported-and-tested-by: syzbot+b24d736f18a1541ad550@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1909171245410.1590-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was using its struct usb_device pointer as an inverted
disconnected flag, but was setting it to NULL before making sure all
completion handlers had run. This could lead to a NULL-pointer
dereference in a number of dev_dbg statements in the completion handlers
which relies on said pointer.
The pointer was also dereferenced unconditionally in a dev_dbg statement
release() something which would lead to a NULL-deref whenever a device
was disconnected before the final character-device close if debugging
was enabled.
Fix this by unconditionally stopping all I/O and preventing
resubmissions by poisoning the interrupt URBs at disconnect and using a
dedicated disconnected flag.
This also makes sure that all I/O has completed by the time the
disconnect callback returns.
Fixes: 1ef37c6047 ("USB: adutux: remove custom debug macro and module parameter")
Fixes: 66d4bc30d1 ("USB: adutux: remove custom debug macro")
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190925092913.8608-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was clearing its struct usb_device pointer, which it used as
an inverted disconnected flag, before deregistering the character device
and without serialising against racing release().
This could lead to a use-after-free if a racing release() callback
observes the cleared pointer and frees the driver data before
disconnect() is finished with it.
This could also lead to NULL-pointer dereferences in a racing open().
Fixes: f08812d5eb ("USB: FIx locks and urb->status in adutux (updated)")
Cc: stable <stable@vger.kernel.org> # 2.6.24
Reported-by: syzbot+0243cb250a51eeefb8cc@syzkaller.appspotmail.com
Tested-by: syzbot+0243cb250a51eeefb8cc@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190925092913.8608-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch fix issue in cdns3_ep0_feature_handle_device function.
The function usleep_range can't be used there because this function is
called with locks held and IRQs disabled in
cdns3_device_thread_irq_handler().
To resolve this issue patch replaces usleep_range with mdelay.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/1569484721-4424-1-git-send-email-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't use "wrap" after it has been freed.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190904100102.GB7007@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing bulk-in endpoint sanity check to prevent uninitialised stack
data from being reported to the system log and used as endpoint
addresses.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+5630ca7c3b2be5c9da5e@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20191003070931.17009-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb-hcd.txt has been converted to YAML. Update references accordingly.
Fixes: 14ec072a19 ("dt-bindings: usb: Convert USB HCD generic binding to YAML")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20191003193132.17758-1-j.neuschaefer@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix NULL-pointer dereferences on open() and write() which can be
triggered by a malicious USB device.
The current URB allocation helper would fail to initialise the newly
allocated URB if the device has unexpected endpoint descriptors,
something which could lead NULL-pointer dereferences in a number of
open() and write() paths when accessing the URB. For example:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:usb_clear_halt+0x11/0xc0
...
Call Trace:
? tty_port_open+0x4d/0xd0
keyspan_open+0x70/0x160 [keyspan]
serial_port_activate+0x5b/0x80 [usbserial]
tty_port_open+0x7b/0xd0
? check_tty_count+0x43/0xa0
tty_open+0xf1/0x490
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:keyspan_write+0x14e/0x1f3 [keyspan]
...
Call Trace:
serial_write+0x43/0xa0 [usbserial]
n_tty_write+0x1af/0x4f0
? do_wait_intr_irq+0x80/0x80
? process_echoes+0x60/0x60
tty_write+0x13f/0x2f0
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:keyspan_usa26_send_setup+0x298/0x305 [keyspan]
...
Call Trace:
keyspan_open+0x10f/0x160 [keyspan]
serial_port_activate+0x5b/0x80 [usbserial]
tty_port_open+0x7b/0xd0
? check_tty_count+0x43/0xa0
tty_open+0xf1/0x490
Fixes: fdcba53e2d ("fix for bugzilla #7544 (keyspan USB-to-serial converter)")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Rio500 kernel driver has not been used by Rio500 owners since 2001
not long after the rio500 project added support for a user-space USB stack
through the very first versions of usbdevfs and then libusb.
Support for the kernel driver was removed from the upstream utilities
in 2008:
943f624ab7
Cc: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/6251c17584d220472ce882a3d9c199c401a51a71.camel@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
