DNOD44CDH086A (NXP TDA18212) tuner module is not connected to
demodulator I2C gate. Instead demodulator gate it uses external
GPIO driven gate. Override demodulator I2C gate control with
own in that case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
refactor MFE code to allow for individual streaming configuration
for each frontend
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change adapter FE pointer as array of FE pointers.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Basically it is just same device as Anysee E7 S2 but made for
internal PCI(e) slot and motherboard USB connector.
Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Basically it is just same device as Anysee E7 TC but made for
internal PCI(e) slot and motherboard USB connector.
Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add some comments about known GPIO settings of supported board
versions.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After that Anysee I2C adapter is capable of one and two byte long
I2C addresses in case of read from I2C bus.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looks like it is IF route switch on IOE[0]. Set it correctly
to route signal from tuner to demod. Now it works for DVB-C too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is ZL10353, TDA10023 and TDA18212.
Tuner is inside of Samsung DNOD44CDH086A tuner module.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New models have new NXP TDA18212 silicon tuner.
Not tested yet due to lack of HW...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use board ID as base value when selecting correct hardware configuration.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Print firmware version as two digit long (change from 3 to 2).
Windows app have changed that too. First byte was hard coded as 0.
Change email list address to report non-working device to current one.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It can read more than one byte from I2C bus. Allow that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,IR_TYPE,RC_TYPE,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_type,rc_type,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch merges the ir_input_dev and ir_dev_props structs into a single
struct called rc_dev. The drivers and various functions in rc-core used
by the drivers are also changed to use rc_dev as the primary interface
when dealing with rc-core.
This means that the input_dev is abstracted away from the drivers which
is necessary if we ever want to support multiple input devs per rc device.
The new API is similar to what the input subsystem uses, i.e:
rc_device_alloc()
rc_device_free()
rc_device_register()
rc_device_unregister()
[mchehab@redhat.com: Fix compilation on mceusb and cx231xx, due to merge conflicts]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a big patch, yet trivial. It just move the RC properties
to a separate struct, in order to prepare the dvb-usb drivers to
use rc-core. There's no change on the behavior of the drivers.
With this change, it is possible to have both legacy and rc-core
based code inside the dvb-usb-remote, allowing a gradual migration
to rc-core, driver per driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb-usb has its own IR handle code. Now that we have a Remote
Controller subsystem, we should start using it. So, remove this
struct, in favor of the similar struct defined at the RC subsystem.
This is a big, but trivial patch. It is a 3 line delect, plus
lots of rename on several dvb-usb files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Smatch complained because "d" is dereferenced first and then checked for
null later . The only code path where "d" could be a invalid pointer is
if this is a cold device in dvb_usb_device_init(). I consulted Antti
Palosaari and he explained that anysee is always a warm device.
I have added a comment and removed the unneeded null check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several DVB drivers use a different name convention. As we're moving
the keytables, we need to use the same convention on all places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
increase BULK transfer size from 512 to 8192 to increase wakeups
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to be closer to V4L IR implementation, it is needed to replace
u8 custom, data
to:
u16 scan
This allows using non-rc5 mappings, like the 8 bit keycodes used on older
protocols. It will also allow future implementations of rc6 keystrokes
when needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
anysee.c:44:5: warning: symbol 'dvb_usb_anysee_delsys' was not declared. Should it be static?
cx24116.c:378:3: warning: symbol 'CX24116_MODFEC_MODES' was not declared. Should it be static?
stb0899_algo.c:57:5: warning: symbol 'stb0899_get_srate' was not declared. Should it be static?
stb0899_algo.c:766:6: warning: symbol 'Log2Int' was not declared. Should it be static?
stb0899_drv.c:137:20: warning: symbol 'stb0899_quant_tab' was not declared. Should it be static?
stb0899_drv.c:180:20: warning: symbol 'stb0899_est_tab' was not declared. Should it be static?
stb0899_drv.c:220:5: warning: symbol '_stb0899_read_reg' was not declared. Should it be static?
budget-ci.c:1348:23: warning: symbol 'tt3200_stb6100_config' was not declared. Should it be static?
/home/v4l/master/v4l/cx25840-core.c:190:6: warning: symbol 'cx25840_work_handler' was not declared. Should it be static?
/home/v4l/master/v4l/m5602_s5k83a.c:116:6: warning: symbol 's5k83a_dump_registers' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/anysee.c: In function ‘anysee_master_xfer’:
drivers/media/dvb/dvb-usb/anysee.c:156: warning: ‘ret’ may be used uninitialized
By looking at the function, altrough very unlikely, this might
eventually be true if num = 0. So, better to fix the warning by
initializing with ret = 0.
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
anysee_usb_mutex is initialized at every time the anysee device is probed.
If the second anysee device is probed while anysee_usb_mutex is locked by
the first anysee device, the mutex is broken.
This patch fixes by initialize anysee_usb_mutex statically rather
than initialize at probe time.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes the needlessly global struct anysee_usb_mutex static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- support for Anysee E30C Plus rev 0.4
- set IO port E
- set correct TS mode
- change deltaf according to latest Windows driver
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
