Suppose TX_ABRT occurs in the middle of processing i2c_msg msgs[], and
a STOP condition has already been generated on the bus. In this case,
subsequent i2c_dw_xfer_msg() might initiate a new and unnecessary I2C
transaction, which we'd have to avoid.
Furthermore, anytime TX_ABRT is set, the contents of tx/rx buffers are
flushed, so we don't have to process RX_FULL and TX_EMPTY.
Disable interrupts, and skip them.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Current error handling procedures are not good in two respects:
* Forgot to mark dev->cmd_complete as "completed" on errors
Once an I2C transaction is initiated, wait_for_completion_
interruptible_timeout() waits for dev->cmd_complete to be completed.
We have to take care of it whenever an error is detected, otherwise
we will have a needless HZ timeout.
* Forgot to disable interrupts
In the previous patch, interrupt mask operations have been changed.
We don't disable interrupts at the end of the interrupt handler any
more, and try to keep RX_FULL (and TX_EMPTY if required) enabled
during the transaction so that we can send longer data than the size
of Tx/Rx FIFO.
If an error is detected, we need to disable interrupts before
quitting current transaction.
We can work around above points using dev->msg_err effectively.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Currently we disable TX_EMPTY interrupt when buf_len is zero, but this
is wrong. (buf_len == 0) means that all transmit data in the current
i2c_msg message has been sent out, but that doesn't necessarily mean
all i2c_msg messages have been processed.
TX_EMPTY interrupt is used as the driving force of DW I2C transactions,
so we need to keep it enabled as long as i2c_msg messages are available.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Currently we process the first i2c_dw_xfer_msg() in i2c_dw_xfer(),
but in this case there is a possibility to be interrupted by certain
interrupts. As described before in this patchset, we need to keep
providing new transmit data within a given time period, otherwise Tx
FIFO underrun takes place and STOP condition will be generated on the
bus, even if we have more bytes to be written.
In order to exclude all such possibilities, change TX_EMPTY interrupt
usage as below:
* DW_IC_INTR_DEFAULT_MASK: Define a default interrupt mask set, and
put TX_EMPTY there.
* i2c_dw_xfer_init: Enable DW_IC_INTR_DEFAULT_MASK prior to initiating
a new I2C transaction. The first TX_EMPTY will be triggered shortly.
With the help of it, we can make the first call to i2c_dw_xfer_msg()
in the interrupt handler.
* i2c_dw_xfer_msg: Fixup intr_mask operation accordingly. Make sure
that TX_EMPTY operations need to be reversed.
* request_irq: Set IRQF_DISABLED so that we could load transmit data
into Tx FIFO without being distracted by other interrupts.
* Remove i2c_dw_xfer_msg() in i2c_dw_xfer().
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
I2c_dw_xfer_msg() also has the same target address inconsistency check,
and furthermore it checks across all i2c_msg messages, while
i2c_dw_read() walks through i2c_msg messages only with_ I2C_M_RD flag.
That is, target address check in i2c_dw_read() is redundant and useless.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Set proper I2C_FUNC_SMBUS_* bits so that the driver could be used with
some utilities requiring SMBus functionalities, such as i2c-tools.
Note that DW I2C core doesn't support I2C_FUNC_SMBUS_QUICK, as it's not
capable of zero-length data transactions.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As the driver and hardware always process the given data in parallel,
then it would be better to initialize tx_limit, rx_limit and rx_valid
variables just prior to being used.
This will help us to send / receive as much data as possible.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
While we have a local variable "buf_len" for dev->tx_buf_len, we don't
have such local variable for dev->tx_buf pointer. While "buf_len" is
restored at first then updated when we start processing a new i2c_msg
(determined by STATUS_WRITE_IN_PROGRESS flag), ->tx_buf is different.
Such inconsistency makes the code slightly hard to follow.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We have some steps at the top of i2c_dw_xfer_msg() to set up a slave
address and enable DW I2C core. And it's executed only when we don't
have STATUS_WRITE_IN_PROGRESS.
But we need to make sure that STATUS_WRITE_IN_PROGRESS only indicates
that we have a pending i2c_msg to process. In other words, even if
STATUS_WRITE_IN_PROGRESS is not set, that doesn't mean we're at initial
state in the I2C transaction.
Since i2c_dw_xfer_msg() will be invoked again and again during a
transaction, those init steps have a possibility to be re-processed
needlessly. For example, this issue easily takes place when processing
a combined transaction with a certain condition (the number of tx bytes
in the first i2c_msg, equals to the Tx FIFO depth).
Consequently we should not use STATUS_WRITE_IN_PROGRESS to determine
where we're at in an I2C transaction. It would be better to separate
those initialization steps from i2c_dw_xfer_msg().
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Enable RX_FULL interrupt mask by default, and hook it in the interrupt
handler. If requested amount of rx data (defined by IC_RX_TL) is not
available, we don't have to process i2c_dw_read().
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As a hardware feature, DW I2C core generates a STOP condition whenever
the Tx FIFO becomes empty (strictly speaking, whenever the last byte in
the Tx FIFO is sent out), even if we have more bytes to be written.
In other words, we must never make "Tx FIFO underrun" happen during
a transaction, except for the last byte. For the safety's sake, we'd
make TX_EMPTY interrupt get triggered every time one byte is processed.
The Rx FIFO threshold needs to be set as well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Symptom:
--------
When we're going to send/receive the longer size of data than the Tx
FIFO length, the I2C transaction will be divided into several separated
transactions, limited by the Tx FIFO length.
Details:
--------
As a hardware feature, DW I2C core generates a STOP condition whenever
the Tx FIFO becomes empty (strictly speaking, whenever the last byte in
the Tx FIFO is sent out), even if we have more bytes to be written.
Then, once a new transmit data is written to the Tx FIFO, DW I2C core
will initiate a new transaction, which leads to another START condition.
This explains how the transaction in question goes, and implies that
current tasklet-based dw_i2c_pump_msg() strategy couldn't meet the
timing constraint required for avoiding Tx FIFO underrun.
To avoid this scenario, we must keep providing new transmit data within
a given time period. In case of Fast-mode + 32-byte Tx FIFO, for
instance, it takes about 22.5[us] to process single byte, and 720[us] in
total.
This patch removes the existing tasklet-based "pump" system, and move
its jobs into the interrupt handler.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In case a work-in-progress i2c_msg has more bytes to be written, we
need to set STATUS_WRITE_IN_PROGRESS and exit from the msg_write_idx-
searching loop. Otherwise, we will overtake the current msg_write_idx
without waiting for its transmission to be processed.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* Calculate with accurate conditional expressions from DW manuals.
* Round ic_clk by adding 0.5 as it's important at high ic_clk rate.
* Take into account "tHD;STA" issue for _HCNT calculation.
* Take into account "tf" for _LCNT calculation.
* Add "cond" and "offset" fot further correction requirements.
For _HCNT calculation, there's one issue needs to be carefully
considered; DesignWare I2C core doesn't seem to have solid strategy
to meet the tHD;STA timing spec. If you configure _HCNT based on the
tHIGH timing spec, it easily results in violation of the tHD;STA spec.
After many trials, we came to the conclusion that the tHD;STA period
is proportional to (_HCNT + 3). For the safety's sake, this should be
selected by default.
As for _LCNT calculation, DW I2C core has one characteristic behavior;
he starts counting the SCL CNTs for the LOW period of the SCL clock
(tLOW) as soon as it pulls the SCL line. At that time, he doesn't take
into account the fall time of SCL signal (tf), IOW, he starts counting
CNTs without confirming the SCL input voltage has dropped to below VIL.
This characteristics becomes a problem on some platforms where tf is
considerably long, and results in violation of the tLOW timing spec.
To make the driver configurable as much as possible for various cases,
we'd have separated arguments "tf" and "offset", and for safety default
values should be 0.3 us and 0, respectively.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We couldn't know the original intent for this variable, but at this
point it's useless.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We don't have to use "struct i2c_adapter" pointer here.
Let's use a local "struct dw_i2c_dev" pointer, instead.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We don't have to use "struct i2c_adapter" pointer here.
Let's use a local "struct dw_i2c_dev" pointer, instead.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We're strongly discouraged from using the IC_CLR_INTR register because
it clears all software-clearable interrupts asserted at the moment.
stat = readl(IC_INTR_STAT);
:
: <=== Interrupts asserted during this period will be lost
:
readl(IC_CLR_INTR);
Instead, use the separately-prepared IC_CLR_* registers.
At the same time, this patch adds all remaining interrupt definitions
available in the DesignWare I2C hardware.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This driver looks originally meant for armel machines where readw()/
writew() works perfectly fine with this hardware. But that doens't
work for big-endian systems.
This patch converts all 8/16-bit-aware usages to 32-bit variants.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a module parameter to override the functionality bitfield. This
lets the user disable some commands. This can be used to force a chip
driver to take different code paths.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The Intel 82801 is sometimes used on systems with a BMC connected. The
BMC can access the SMBus, resulting in lost arbitration for the 82801.
We should let i2c-core retry transactions for us in this case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I2C bus drivers don't have to support I2C_M_REV_DIR_ADDR. It is a
deviation from the I2C specification, which only makes sense to
implement when really needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Superseded by tdfxfb. I2C/DDC support used to live in a separate
driver but this caused driver conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
We no longer need to write the adapter name to a temporary buffer.
We can write it directly to the i2c_adapter's name field. This is
more efficient.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Include the i2c_adapter in struct pmac_i2c_bus. This avoids memory
fragmentation and allows for several code cleanups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Log errors when they happen, otherwise we have no idea what went
wrong.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
I wanted to add some error logging to the i2c-powermac driver, but
found that it was very difficult due to the way the
i2c_powermac_smbus_xfer function is organized. Refactor the code in
this function so that each low-level function is only called once.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
The i2c-powermac driver doesn't support arbitrary multi-message I2C
transactions, only SMBus ones. Make it clear by returning an error if
a multi-message I2C transaction is attempted. This is better than only
processing the first message, because most callers won't recover from
the short transaction. Anyone wishing to issue multi-message
transactions should use the SMBus API instead of the raw I2C API.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
The existing interface only has a pre-order callback. This change
adds an additional parameter for a post-order callback which will
be more useful for bus scans. ACPICA BZ 779.
Also update the external calls to acpi_walk_namespace.
http://www.acpica.org/bugzilla/show_bug.cgi?id=779
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This allows i2c-pnx to free its interrupt handler when the module
is removed or if an error occurs; using the same dev_id for both
request_irq and free_irq is desirable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Added missing mach/i2c.h and linux/io.h header file includes
Signed-off-by: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Limit minimum jiffie timeout to 2 to prevent early timeout on systems
with low tick rates
Signed-off-by: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The driver always ends a read with a STOP condition which
breaks subsequent I2C reads/writes in the same transaction as
these expect to do a repeated START(ReSTART).
This will also help I2C multimaster as the bus will not be released
after the first read, but when the whole transaction ends.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The controller can't do anything else before it actually generates START/STOP.
So we check busy bit to make sure START/STOP is successfully finished.
If we don't check busy bit, START/STOP may fail on some fast CPUs.
Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When an ACPI resource conflict is detected, error messages are already
printed by ACPI. There's no point in causing the driver core to print
more error messages, so return one of the error codes for which no
message is printed.
This fixes bug #14293:
http://bugzilla.kernel.org/show_bug.cgi?id=14293
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We recently removed the acpi_device_uid() interface because nobody
used it. I don't think it's essential here either.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Clearly mark ACPI drivers as such
i2c: Add driver for SMBus Control Method Interface
i2c-pnx: Correct use of request_region/request_mem_region
MAINTAINERS: Add maintainer for AT24 and PCA9564/PCA9665
i2c-piix4: Add AMD SB900 SMBus device ID
i2c/chips: Remove deprecated pcf8574 driver
i2c/chips: Remove deprecated pca9539 driver
i2c/chips: Remove deprecated pcf8575 driver
gpio/pcf857x: Copy i2c_device_id from old pcf8574 driver
i2c/scx200_acb: Provide more information on bus errors
i2c: Provide compatibility links for i2c adapters
i2c: Convert i2c adapters to bus devices
i2c: Convert i2c clients to a device type
i2c/tsl2550: Use combined SMBus transactions
i2c-taos-evm: Switch echo off to improve performance
i2c: Drop unused i2c_driver.id field
As I2C is used by PMICs also, make the busses available early via
subsys_initcall().
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The mv64xxx_i2c_intr() irq handler in drivers/i2c/busses/i2c-mv64xxx.c
is declared as returning 'int', resulting in this compile-time warning:
drivers/i2c/busses/i2c-mv64xxx.c: In function 'mv64xxx_i2c_probe':
drivers/i2c/busses/i2c-mv64xxx.c:540: warning: passing argument 2 of 'request_irq' from incompatible pointer type
Fix: correct the return type to 'irqreturn_t'.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Now that we have ACPI-based SMBus controller drivers, and we will start
telling users to use them instead of native drivers when I/O resources
conflict, I think it would be good to clearly mark ACPI drivers as such
in Kconfig.
This is exactly the same as we just did for hwmon drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Crane Cai <crane.cai@amd.com>
This driver supports the SMBus Control Method Interface. It needs BIOS declare
ACPI control methods which described in SMBus Control Method Interface Spec.
http://smbus.org/specs/smbus_cmi10.pdf
Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
request_mem_region should be used when ioremap is used subsequently.
release_region is then correspondingly replaced by release_mem_region.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression start,E;
@@
- request_region
+ request_mem_region
(start,...)
... when != request_mem_region(start,...)
when != start = E
ioremap(start,...)
@@
expression r.start;
@@
- release_region
+ release_mem_region
(start,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upon a bus error, it's rather hard to guess what happened. Dumping the
address, length and status provides a lot of value for troubleshooting
issues.
Signed-off-by: Willy Tarreau <wtarreau@exceliance.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When echo is on, we waste time reading back our orders. Switching echo
off makes performance much better: SMBus byte data transactions are 47%
faster and byte transactions are 24% faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
PXA I2C module is also used in Marvell PXA168 and PXA910 series.
Update the module dependancy of PXA I2C.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch modifies the SuperH Mobile I2C driver to support
Runtime PM. These changes is all that is needed for proper
Runtime PM support in this driver. Driver callbacks for
Runtime PM are empty because the device registers are always
re-initialized after pm_runtime_get_sync().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- blk clk is enabled when an irq arrives. The clk should be enabled,
but just to make sure.
- All error bits are handled no matter state machine state
- All irq's will run complete() except for irq's that wasn't an event.
- No more looking into status registers just in case an interrupt
has happend and the irq handle wasn't executed.
- irq_disable/enable are now separete functions.
- clk settings calculation changed to round upwards instead of
downwards.
- Number of address send attempts before giving up is increased to 12
from 10 since it most times take 8 tries before getting through.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later
version of I2C IP block.
The errata impacts OMAP 2420|2430|3430, enable the workaround for these based
on I2C IP block revision number instead of OMAP CPU type
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When an XRDY/XDR is hit, wait for XUDF before writing data to DATA_REG.
Otherwise some data bytes can be lost while transferring them from the
memory to the I2C interface.
Do a Busy-wait for XUDF, before writing data to DATA_REG. While waiting
if there is NACK | AL, set the appropriate error flags, ack the pending
interrupts and return from the ISR.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In case of a NACK or ARDY or AL interrupt, complete the request.
There is no need to service the RRDY/RDR or XRDY/XDR interrupts.
Refer TRM SWPU114: Figure 18-31.I2C Master Transmitter Mode, Interrupt Method,
in F/S and HS Modes
http://focus.ti.com/pdfs/wtbu/SWPU114T_PrelimFinalEPDF_06_25_2009.pdf
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix bug in reading the I2C_BUFFSTAT register for getting byte count on RX/TX interrupt.
On Interrupt: I2C_STAT[RDR],
read 'RXSTAT' from I2C_BUFFSTAT[8-13]
On Interrupt: I2C_STAT[XDR]
read 'TXSTAT' from I2C_BUFFSTAT[0-5]
Signed-off-by: Jagadeesh Pakaravoor <j-pakaravoor@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Convert the i2c-sh_mobile i2c bus driver to use
subsys_initcall() instead of module_init().
This change makes the driver register a bit earlier which
together with earlier platform data moves the time for probe().
The earlier probe() makes it possible to use i2c_get_adapter()
and i2c_transfer() from device_initcall().
The same strategy is used by other i2c bus drivers such as
i2c-pxa.c and i2c-s3c2410.c.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
[ben-linux@fluff.org: minor subject updaye]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
s3c24xx_i2c_init() was overwriting the IICLC value set just above in
s3c24xx_i2c_clockrate() with zero, effectively disabling the platform
line control setting.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is V2 of the i2c-s3c2410 dev_pm_ops patch.
The callbacks are converted for CONFIG_SUSPEND like this:
suspend_late() -> suspend_noirq()
resume() -> resume()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch reworks platform driver power management code
for i2c-pxa from legacy late/early callbacks to dev_pm_ops.
The callbacks are converted for CONFIG_SUSPEND like this:
suspend_late() -> suspend_noirq()
resume_early() -> resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make i2c-davinci cope properly with "i2cdetect": don't spew
syslog spam on perfectly normal behaviors, or respond to any
address other than the one reserved for the SMBus host.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
DaVinci core code has converted to the new clkdev API so
clock name strings are not needed. Instead, just the a
'struct device' pointer is needed.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This build error triggers on x86:
drivers/built-in.o: In function `i2c_dw_init':
i2c-designware.c:(.text+0x4e37ca): undefined reference to `clk_get_rate'
drivers/built-in.o: In function `dw_i2c_probe':
i2c-designware.c:(.devinit.text+0x51f5e): undefined reference to `clk_get'
i2c-designware.c:(.devinit.text+0x51f76): undefined reference to `clk_enable'
i2c-designware.c:(.devinit.text+0x520ff): undefined reference to `clk_disable'
i2c-designware.c:(.devinit.text+0x52108): undefined reference to `clk_put'
Because this new driver uses the clk_*() facilities which is an
ARM-only thing currently.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i2c Linux driver for the DesignWare i2c block of Synopsys, which is meant
for AMBA Peripheral Bus. This i2c block is used on SoC chips like the ARM9
based PVG610.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When a process tries to read/write a disconnected i2c device, it receives a signal (e.g. ctrl-c) and the kernel gets stuck.
BUG: soft lockup - CPU#0 stuck for 61s! [I2CEEpromTest:392]
NIP: c01628f8 LR: c01628f0 CTR: c00177cc
REGS: c39abd70 TRAP: 0901 Not tainted (2.6.25.7-alcore)
MSR: 00009032 <EE,ME,IR,DR> CR: 42042048 XER: 20000000
TASK = c3889bd0[392] 'I2CEEpromTest' THREAD: c39aa000
GPR00: 00009000 c39abe20 c3889bd0 c39075c8 c39abe28 00000001 00000000 00000001
GPR08: c3889bd0 c39075c8 00009032 c39abe34 00002437
NIP [c01628f8] cpm_i2c_xfer+0x5fc/0x6d0
LR [c01628f0] cpm_i2c_xfer+0x5f4/0x6d0
Call Trace:
[c39abe20] [c0162924] cpm_i2c_xfer+0x628/0x6d0 (unreliable)
[c39abe90] [c015f6a0] i2c_transfer+0x88/0xb4
[c39abeb0] [c0160164] i2c_master_recv+0x48/0x6c
[c39abed0] [c01618dc] i2cdev_read+0x50/0xe4
[c39abef0] [c0068b24] vfs_read+0xc4/0x108
[c39abf10] [c0068f4c] sys_read+0x4c/0x90
[c39abf40] [c000d348] ret_from_syscall+0x0/0x38
Instruction dump:
3bc00064 92610010 3bf201c8 92810014 3b61
This happen because though the wait_event_interruptible_timeout takes the
signals into account, the driver does not handle them.
We propose to change the wait_event_interruptible_timeout with
wait_event_timeout, leaving the signals to be handled in other points
on the upper layers.
Signed-off-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
[ben-linux@fluff.org: fix title for patch]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Hi Ben,
Can you please queue this fix?
Thanks,
Tony
>From ffe2b2cdf6283770b70a197e3748c6b40a1006be Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Wed, 17 Jun 2009 13:14:23 +0300
Subject: [PATCH] i2c-omap: Fix build breaking typo in cpu_is_omap_2430
Commit 84bf2c86 introduced a typo, it should be cpu_is_omap2430
instead. The typo was probably caused by a mismerge.
Without this patch all omaps fail to build with:
error: implicit declaration of function 'cpu_is_omap_2430'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different
clock names (IPS vs. IPB) the code was identical.
Use common code for both processor families.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This makes the stu300 driver for the ST Micro ST DDC I2C bus
driver depend on MACH_U300, new platforms reusing this I2C
driver will need to add in a similar dependency.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
[ben-linux@fluff.org: re-aranged subject line]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This replace all instances in the i2c busses tree of
res->end - res->start + 1 with the handy macro resource_size(res)
from ioport.h (coming in from platform_device.h).
This was created with a simple
sed -i -e 's/\([a-z]*\)->end *- *[a-z]*->start *+ *1/resource_size(\1)/g'
Then manually replacing the PXA redefiniton of the same kind
of macro manually. Recompiled some ARM defconfigs I could find to
make a rough test so it shouldn't break anything, though I
couldn't see exactly which configs you need for all the drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds support for the ST Microelectronics DDC I2C bus
driver. This bus is used in the U300 architecture recently
added to RMK:s ARM tree.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Ben Dooks <ben-linux@fluff.org>
Reviewed-by: Jean Delvare <khali@linus-fr.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rather than relying on some of the headers implicitly pulling in io.h,
pull it in explicitly our self for ioremap() and friends.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
therm_windtunnel: Convert to a new-style i2c driver
therm_adt746x: Convert to a new-style i2c driver
windfarm: Convert to new-style i2c drivers
therm_pm72: Convert to a new-style i2c driver
i2c-viapro: Add new PCI device ID for VX855
i2c/chips: Move max6875 to drivers/misc/eeprom
i2c: Do not give adapters a default parent
i2c: Do not probe for TV chips on Voodoo3 adapters
i2c: Retry automatically on arbitration loss
i2c: Remove void casts
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
powerpc: Fix bug in move of altivec code to vector.S
powerpc: Add support for swiotlb on 32-bit
powerpc/spufs: Remove unused error path
powerpc: Fix warning when printing a resource_size_t
powerpc/xmon: Remove unused variable in xmon.c
powerpc/pseries: Fix warnings when printing resource_size_t
powerpc: Shield code specific to 64-bit server processors
powerpc: Separate PACA fields for server CPUs
powerpc: Split exception handling out of head_64.S
powerpc: Introduce CONFIG_PPC_BOOK3S
powerpc: Move VMX and VSX asm code to vector.S
powerpc: Set init_bootmem_done on NUMA platforms as well
powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
powerpc/mm: Fix some SMP issues with MMU context handling
powerpc: Add PTRACE_SINGLEBLOCK support
fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
powerpc/virtex: Add ml510 reference design device tree
powerpc/virtex: Add Xilinx ML510 reference design support
powerpc/virtex: refactor intc driver and add support for i8259 cascading
powerpc/virtex: Add support for Xilinx PCI host bridge
...
The south bridge of the VIA VX855 chipset has a different PCI Device ID
so i2c-viapro.c needs to be updated with this.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There's no point in giving the I2C bus of Voodoo3 adapters a class
value, there's no video chip driver checking for it anymore. If
support is ever needed, the video device should be instantiated
explicitly rather than probed.
To the best of my knowledge the only video chip that can be found on
these boards is a BT869 video encoder, for which no support exists
currently.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
There is sometimes a need for the ocores driver to add devices to the
bus when installed.
i2c_register_board_info can not always be used, because the I2C devices
are not known at an early state, they could for instance be connected
on a I2C bus on a PCI device which has the Open Cores IP.
i2c_new_device can not be used in all cases either since the resulting
bus nummer might be unknown.
The solution is the pass a list of I2C devices in the platform data to
the Open Cores driver. This is useful for MFD drivers.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change to using platform id table to match either of the two supported
platform device names in the driver. This simplifies the driver init and
exit code
Note, log messages will now be prefixed with 's3c-i2c' instead of the
driver name, so output will be of the form of:
s3c-i2c s3c2440-i2c.0: slave address 0x10
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use longer noise filter period for fast and standard mode. Based on an
earlier patch by Eero Nurkkala.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix scll/sclh calculations for HS and fast modes. Currently the driver
uses equal (roughly) low/high times which will result in too short
low time.
OMAP3430 TRM gives the following equations:
F/S: tLow = (scll + 7) * internal_clk
tHigh = (sclh + 5) * internal_clk
HS: tLow = (scll + 7) * fclk
tHigh = (sclh + 5) * fclk
Furthermore, the I2C specification sets the following minimum values
for HS tLow/tHigh for capacitive bus loads 100 pF (maximum speed 3400)
and 400 pF (maximum speed 1700):
speed tLow tHigh
3400 160 ns 60 ns
1700 320 ns 120 ns
and for F/S:
speed tLow tHigh
400 1300 ns 600 ns
100 4700 ns 4000 ns
By using duty cycles 33/66 (HS, F) and 50/50 (S) we stay above these
minimum values.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some drivers need i2c_smbus_read_i2c_block_data() functionality, so add
support for it to the Blackfin I2C bus driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
[ben-linux@fluff.org: shortened subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We have a custom BF537 board with an I2C RTC (MAX DS3231) running
uclinux 2007R1 for some time. Recently during migration to 2008R1.5-RC3
we losted access to the RTC. The RTC driver calls 'i2c_transfer()' which
in turns calls 'bfin_twi_master_xfer()' in i2c-bfin-twi.c.
Compared with 2007R1, it looks like the 2008R1.5 version of i2c-bin-twi.c
has a new mode 'TWI_I2C-MODE_REPEAT' which corresponds to the Repeat Start
Condition described in the HRM. However, according to the HRM, at XMIT or
RECV interrupt and when the data count is 0, not only is the RESTART bit
supposed to be set, but MDIR must also be set if the next operation is a
receive sequence, and cleared if not. Currently there is no code that looks
at the I2C_M_RD bit in the flag from the next cur_msg and set/clear the MDIR
flag accordingly at the same time that the RSTART bit is set. Instead, MDIR
is set or cleared (by OR'ing with 0?) after the RESTART bit has been cleared
during handling of MCOMP interrupt.
It appears that this is causing our failure with reading the RTC, as a
quick patch to set/clear MDIR when RESTART is set seem to solve our problem.
Signed-off-by: Frank Shew <fshew@geometrics.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Avoid rewrite TWI MASTER_CTL reg when issue next message
In i2c repeat transfer mode, byte count of next message should be filled
into part of the TWI MASTER_CTL reg when interrupt MCOMP of last
message transfer is triggered. But, other bits in this reg should
not be touched.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make sure we don't end up with an invalid CLKDIV=0 in case someone
specifies 20kHz SCL or less (5 * 1024 / 20 = 0x100).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shortened subject line]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The i2c-ibm_iic driver printed messages in an odd order that seemed
to list devices before the driver was probed.
Here is an example:
at24 0-0052: 512 byte 24c04 EEPROM (writable)
ibm-iic ef600700.i2c: using standard (100 kHz) mode
ad7414 0-004a: chip found
This changes the order to print the i2c driver message before scanning
for devices so that the logs show the driver, then the devices.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
For consistenct naming, and to allow us to fix up some confusion in the
SH-Mobile clock framework, amongst other places.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'i2c-for-2630-rc5' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-cpm: Pass dev ptr to dma_*_coherent rather than NULL
i2c: Enable i2c-s3c2410 for S3C64XX too
i2c-mpc: bug fix for MPC52xx clock setting and printout
i2c-pxa.c: timeouts off by 1
Recent DMA changes result in a BUG() when NULL is passed to
dma_alloc_coherent in place of a device.
Signed-off-by: Mark Ware <mware@elphinstone.net>
[ben-linux@fluff.org: fix patch moves]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This controller is also present on the S3C64xx series processors so
enable the driver in Kconfig for those platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clock setting did not work for the MPC52xx due to a stupid bug.
Furthermore, the dev info output "clock=0" for old device trees was
misleading. This patch fixes both issues.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
with while (timeout++ < MAX_TIMEOUT); timeout reaches MAX_TIMEOUT + 1
after the loop, so the tests below are off by one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
With `while (timeout--)' timeout reaches -1 after the loop, so the tests
below are off by one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Support for I2C/DDC was recently added to the tdfxfb driver, which
means that the i2c-voodoo3 driver can be deprecated.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
'disable_delay' was static which is wrong as it is calculated using the per-device
bus speed. This patch turns 'disable_delay' into a per-device variable.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Support for the s6000 on-chip i2c controller.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch makes the I2C bus speed configurable by using the I2C node
property "clock-frequency". If the property is not defined, the old
fixed clock settings will be used for backward comptibility.
The generic I2C clock properties, especially the CPU-specific source
clock pre-scaler are defined via the OF match table:
static const struct of_device_id mpc_i2c_of_match[] = {
...
{.compatible = "fsl,mpc8543-i2c",
.data = &(struct fsl_i2c_match_data) {
.setclock = mpc_i2c_setclock_8xxx,
.prescaler = 2,
},
},
The "data" field defines the relevant I2C setclock function and the
relevant pre-scaler for the I2C source clock frequency.
It uses arch-specific tables and functions to determine resonable
Freqency Divider Register (fdr) values for MPC83xx, MPC85xx, MPC86xx,
MPC5200 and MPC5200B.
The i2c->flags field and the corresponding FSL_I2C_DEV_* definitions
have been removed as they are obsolete.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch used the dev_dbg, dev_err, etc. functions for debug
and error output instead of printk and pr_debug.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix errors reported by checkpatch (indention, long lines, trailing
white space, etc.).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
[ben-linux@fluff.org: fix minor patch fault in remove]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is required in order to ensure that core system devices such as
voltage regulators attached via I2C are avaiable early in boot.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.
This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The sda_delay field should be specified in ns, not in clock ticks
as when using cpufreq we could be changing the bus rate.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Implementation of I2C Adapter/Algorithm Driver for I2C Bus integrated
in Freescale's i.MX/MXC processors.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (fschmd) Add support for the FSC Hades IC
hwmon: (fschmd) Add support for the FSC Syleus IC
i2c-i801: Instantiate FSC hardware montioring chips
dmi: Let dmi_walk() users pass private data
hwmon: Define a standard interface for chassis intrusion detection
Move the pcf8591 driver to hwmon
hwmon: (w83627ehf) Only expose in6 or temp3 on the W83667HG
hwmon: (w83627ehf) Add support for W83667HG
hwmon: (w83627ehf) Invert fan pin variables logic
hwmon: (hdaps) Fix Thinkpad X41 axis inversion
hwmon: (hdaps) Allow inversion of separate axis
hwmon: (ds1621) Clean up documentation
hwmon: (ds1621) Avoid unneeded register access
hwmon: (ds1621) Clean up register access
hwmon: (ds1621) Reorder code statements
Detect various FSC hwmon IC's based on DMI tables and then let
the i2c-i801 driver instantiate the i2c client devices. Note that
some of the info in the added table is indentical for all rows, still
this is kept in the table to keep the code general and thus (hopefully)
easily extensible in the future.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-core: Some style cleanups
i2c-piix4: Add support for the Broadcom HT1100 chipset
i2c-piix4: Add support to SB800 SMBus changes
i2c-pca-platform: Use defaults if no platform_data given
i2c-algo-pca: Use timeout for checking the state machine
i2c-algo-pca: Rework waiting for a free bus
i2c-algo-pca: Add PCA9665 support
i2c: Adapt debug macros for KERN_* constants
i2c-davinci: Fix timeout handling
i2c: Adapter timeout is in jiffies
i2c: Set a default timeout value for all adapters
i2c: Add missing KERN_* constants to printks
i2c-algo-pcf: Handle timeout correctly
i2c-algo-pcf: Style cleanups
eeprom/at24: Remove EXPERIMENTAL
i2c-nforce2: Add support for MCP67, MCP73, MCP78S and MCP79
i2c: Clarify which clients are auto-removed
i2c: Let checkpatch shout on users of the legacy model
i2c: Document the different ways to instantiate i2c devices
Add support for the Broadcom HT1100 LD chipset (SMBus function.)
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the AMD SB800 Family series of products.
Major changes include the changes to addressing the SMBus registers at different
location from the locations in the previous compatible parts from AMD such as
SB400/SB600/SB700. For SB800, the main features and register definitions of
SMBus and other interfaces are still compatible with the previous products with
the only change being in how to access the internal registers for these blocks.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We now timeout also if the state machine does not change within the
given time. For that, the driver-specific completion-functions are
extended to return true or false depending on the timeout. This then
gets checked in the algorithm.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Waiting for a free bus now accepts the timeout value in jiffies and does
proper checking using time_before.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Properly set the adapter timeout value in jiffies, and then use that
value in the driver, rather than a hard-coded constant.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Kevin Hilman <khilman@mvista.com>
i2c_adapter.timeout is in jiffies. Fix all drivers which thought
otherwise. It didn't really matter as long as the value was only used
inside the driver, but soon i2c-core will use it too so it must have
the proper unit.
Note: for the i2c-mpc driver, this fixes a bug in polling mode.
Timeout would trigger after 1 jiffy, which is most probably not what
the author wanted.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Clifford Wolf <clifford@clifford.at>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Mark A. Greer <mgreer@mvista.com>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing pieces here for the i2c subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The MCP78S and MCP79 appear to be compatible with the previous nForce
chips as far as the SMBus controller is concerned. The MCP67 and MCP73
were not tested yet but I'd be very surprised if they weren't
compatible too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Oleg Ryjkov <olegr@olegr.ca>
Cc: Malcolm Lalkaka <mlalkaka@gmail.com>
Cc: Zbigniew Luszpinski <zbiggy@o2.pl>
The i2c_wait() function is using wait_event_interruptible_timeout() to wait for
the I2C controller to signal that it has completed an I2C bus operation. If
the process that causes the I2C operation terminated abruptly, the wait will
be interrupted, returning an error. It is better to let the I2C operation
finished before the process exits.
It is safe to use wait_event_timeout() instead, because the timeout will allow
the process to exit if the I2C bus hangs. It's also better to allow the
I2C operation to finish, because unacknowledged I2C operations can cause the
I2C bus to hang.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the necessary i2c_board_info structure to fix the lack of PCF8583
RTC on RiscPC.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
i2c_algo_bit_data.timeout is supposed to be in jiffies, so drivers
should use set this value in terms of HZ.
Ultimately I think this field should be discarded in favor of
i2c_adapter.timeout, but that's left for a future patch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
With a postfix decrement these timeouts reach -1 rather than 0, but
after the loop it is tested whether they have become 0.
As pointed out by Jean Delvare, the condition we are waiting for should
also be tested before the timeout. With the current order, you could
exit with a timeout error while the job is actually done.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If dev->id is not -1, the platform code may use static bus numbering
rather than dynamic. The patch also changes the i2c_versatile_init to a
subsys_initcall rather than module_init to make sure it is initialised
before the I2C devices initialisation.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By providing a dummy ick for OMAP1510 and OMAP310, we avoid having
SoC conditional clock information in i2c-omap.c. Also, fix the
error handling by making sure we propagate the error returned via
clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On OMAP1, the I2C functional clock (fck) is the armxor_ck, so there's
no need to get "armxor_ck" separately.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
