The check that beacon primary channel is in the range of 80 MHz
(abs < 80) is invalid for 320 MHz since duplicate beacon transmit
means that the AP transmits it on all the 20 MHz sub-channels:
9.4.2.249 HE Operation element - ... AP transmits Beacon frames in
non-HT duplicate PPDU with a TXVECTOR parameter CH_BANDWIDTH value
that is up to the BSS bandwidth.
So in case of 320 MHz the DUP beacon can be in upper 160 for primary
channel in the lower 160 giving possibly an absolute range of over
80 MHz.
Also this check is redundant alltogether, if AP has a wrong primary
channel in the beacon it's a faulty AP, and we would fail in next
steps to connect.
While at it, fix the frequency comparison to no longer compare
between KHz and MHz, which was introduced by commit 7f599aeccb
("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel").
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.314faf725255.I5e27251ac558297553b590d3917a7b6d1aae0e74@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently in case DUP bit is not set we don't return the primary
channel for 6 GHz Band, but the spec says that the DUP bit has
no effect on this field:
9.4.2.249 HE Operation element:
The Duplicate Beacon subfield is set to 1 if the AP transmits
Beacon frames in non-HT duplicate PPDU with a TXVECTOR parameter
CH_BANDWIDTH value that is up to the BSS bandwidth and is set to
0 otherwise.
So remove the condition for returning primary channel based on DUP.
Since the caller code already marks the signal as invalid in case
the indicated frequency is not the tuned frequency, there's no need
to additionally handle this case here since that's already true for
duplicated beacons on the non-primary channel(s).
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.66d7f05f7d11.I5e0add054f72ede95611391b99804c61c40cc959@changeid
[clarify commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Third set of patches for v6.2. mt76 has a new driver for mt7996 Wi-Fi 7
devices and iwlwifi also got initial Wi-Fi 7 support. Otherwise
smaller features and fixes.
Major changes:
ath10k
* store WLAN firmware version in SMEM image table
mt76
* mt7996: new driver for MediaTek Wi-Fi 7 (802.11be) devices
* mt7986, mt7915: enable Wireless Ethernet Dispatch (WED) offload support
* mt7915: add ack signal support
* mt7915: enable coredump support
* mt7921: remain_on_channel support
* mt7921: channel context support
iwlwifi
* enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
* 320 MHz channels support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmOKcMARHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZv3cgf+KjlbxtCZvEIfK+jsd2/VK635ucUdC1d5
QZB5SCHyVCqTMEsBBw0WCmFdfnqQRQUE9Qe5s0hlwhyrjLP4FQ6/jGTarFvRV43E
xO8jJd7e4mnVVoQySeKIRfvtYPFKT5GpaDVs4ytfdSs+KYoCE7akMBcvHVO8Fr2M
MepdqyoJakhRybFUJZMts8W8IsBikv9hdnb2Mr/E32JFLeP6ggs9tKCZKBbpxyXk
BzfYkDMXffFl95prlmy4rXP223FjvgUuRNWaatseR7S6A/Ik9Xk3B1qv3mtocPZF
LiTlFtmn3qkgyX5bfm6NRe/2FqgRUYfIrN0XtVw6Sy8WUe1GCf3opA==
=pkqE
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.2
Third set of patches for v6.2. mt76 has a new driver for mt7996 Wi-Fi 7
devices and iwlwifi also got initial Wi-Fi 7 support. Otherwise
smaller features and fixes.
Major changes:
ath10k
- store WLAN firmware version in SMEM image table
mt76
- mt7996: new driver for MediaTek Wi-Fi 7 (802.11be) devices
- mt7986, mt7915: enable Wireless Ethernet Dispatch (WED) offload support
- mt7915: add ack signal support
- mt7915: enable coredump support
- mt7921: remain_on_channel support
- mt7921: channel context support
iwlwifi
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
* tag 'wireless-next-2022-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (144 commits)
wifi: ath10k: fix QCOM_SMEM dependency
wifi: mt76: mt7921e: add pci .shutdown() support
wifi: mt76: mt7915: mmio: fix naming convention
wifi: mt76: mt7996: add support to configure spatial reuse parameter set
wifi: mt76: mt7996: enable ack signal support
wifi: mt76: mt7996: enable use_cts_prot support
wifi: mt76: mt7915: rely on band_idx of mt76_phy
wifi: mt76: mt7915: enable per bandwidth power limit support
wifi: mt76: mt7915: introduce mt7915_get_power_bound()
mt76: mt7915: Fix PCI device refcount leak in mt7915_pci_init_hif2()
wifi: mt76: do not send firmware FW_FEATURE_NON_DL region
wifi: mt76: mt7921: Add missing __packed annotation of struct mt7921_clc
wifi: mt76: fix coverity overrun-call in mt76_get_txpower()
wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices
wifi: mt76: mt76x0: remove dead code in mt76x0_phy_get_target_power
wifi: mt76: mt7915: fix band_idx usage
wifi: mt76: mt7915: enable .sta_set_txpwr support
wifi: mt76: mt7915: add basedband Txpower info into debugfs
wifi: mt76: mt7915: add support to configure spatial reuse parameter set
wifi: mt76: mt7915: add missing MODULE_PARM_DESC
...
====================
Link: https://lore.kernel.org/r/20221202214254.D0D3DC433C1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no need to open-code container_of() when we have
bss_from_pub(). Use it.
Change-Id: I074723717909ba211a40e6499f0c36df0e2ba4be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the "channel->freq_offset" comparison is omitted in cmp_bss(),
BSS with different kHz units cannot be distinguished in the S1G Band.
So "freq_offset" should also be included in the comparison.
Signed-off-by: JUN-KYU SHIN <jk.shin@newratek.com>
Link: https://lore.kernel.org/r/20221111023301.6395-1-jk.shin@newratek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In S1G beacon frames there shouldn't be multi-BSSID elements
since that's not supported, remove that to avoid a potential
integer underflow and/or misparsing the frames due to the
different length of the fixed part of the frame.
While at it, initialize non_tx_data so we don't send garbage
values to the user (even if it doesn't seem to matter now.)
Reported-and-tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 9eaffe5078 ("cfg80211: convert S1G beacon to scan results")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For vendor elements, the code here assumes that 5 octets
are present without checking. Since the element itself is
already checked to fit, we only need to check the length.
Reported-and-tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Second set of patches for v6.2. Only driver patches this time, nothing
really special. Unused platform data support was removed from wl1251
and rtw89 got WoWLAN support.
Major changes:
ath11k
* support configuring channel dwell time during scan
rtw89
* new dynamic header firmware format support
* Wake-over-WLAN support
rtl8xxxu
* enable IEEE80211_HW_SUPPORT_FAST_XMIT
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmN3ZagRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuk/Af+M9IXyWmis9behHlz2U+4PJ/+JF8VYIck
6Xup+FM0O1w6aHhAL8gNOhLl62jpYB0Exou0YizInGvwjjQk2Gtuq60KshkbN2zL
YK3sbcS66PyE19gfIQKJTW/s+9aBncRuvEb6HTZx5iF96mVFPeBDPduUGQksGs5/
Egf03eAqzdcIIcejKG1SUn2o0fLJ6jds0VftAas+chKI2Z5ADQWPzugvU0vlvXVE
oq3ws7Sg0yGcwOOttFwaXMBPrjmCty5uc/ELMhjvSLAsKULXymjZkrU1m5tanhGu
N1MDqviwCK7PJC/wQ2xo7YKNY/1LUc0xbwfbEXQITfbbPyjOz+ynQQ==
=wKQZ
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.2
Second set of patches for v6.2. Only driver patches this time, nothing
really special. Unused platform data support was removed from wl1251
and rtw89 got WoWLAN support.
Major changes:
ath11k
* support configuring channel dwell time during scan
rtw89
* new dynamic header firmware format support
* Wake-over-WLAN support
rtl8xxxu
* enable IEEE80211_HW_SUPPORT_FAST_XMIT
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When built with Control Flow Integrity, function prototypes between
caller and function declaration must match. These mismatches are visible
at compile time with the new -Wcast-function-type-strict in Clang[1].
Fix a total of 73 warnings like these:
drivers/net/wireless/intersil/orinoco/wext.c:1379:27: warning: cast from 'int (*)(struct net_device *, struct iw_request_info *, struct iw_param *, char *)' to 'iw_handler' (aka 'int (*)(struct net_device *, struct iw_request_info *, union iwreq_data *, char *)') converts to incompatible function type [-Wcast-function-type-strict]
IW_HANDLER(SIOCGIWPOWER, (iw_handler)orinoco_ioctl_getpower),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../net/wireless/wext-compat.c:1607:33: warning: cast from 'int (*)(struct net_device *, struct iw_request_info *, struct iw_point *, char *)' to 'iw_handler' (aka 'int (*)(struct net_device *, struct iw_request_info *, union iwreq_data *, char *)') converts to incompatible function type [-Wcast-function-type-strict]
[IW_IOCTL_IDX(SIOCSIWGENIE)] = (iw_handler) cfg80211_wext_siwgenie,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/net/wireless/intersil/orinoco/wext.c:1390:27: error: incompatible function pointer types initializing 'const iw_handler' (aka 'int (*const)(struct net_device *, struct iw_request_info *, union iwreq_data *, char *)') with an expression of type 'int (struct net_device *, struct iw_request_info *, struct iw_param *, char *)' [-Wincompatible-function-pointer-types]
IW_HANDLER(SIOCGIWRETRY, cfg80211_wext_giwretry),
^~~~~~~~~~~~~~~~~~~~~~
The cfg80211 Wireless Extension handler callbacks (iw_handler) use a
union for the data argument. Actually use the union and perform explicit
member selection in the function body instead of having a function
prototype mismatch. There are no resulting binary differences
before/after changes.
These changes were made partly manually and partly with the help of
Coccinelle.
Link: https://github.com/KSPP/linux/issues/234
Link: https://reviews.llvm.org/D134831 [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/a68822bf8dd587988131bb6a295280cb4293f05d.1667934775.git.gustavoars@kernel.org
All we're going to do with this pointer is assign it to
another __rcu pointer, but sparse can't see that, so
use rcu_access_pointer() to silence the warning here.
Fixes: c90b93b5b7 ("wifi: cfg80211: update hidden BSSes to avoid WARN_ON")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When updating beacon elements in a non-transmitted BSS,
also update the hidden sub-entries to the same beacon
elements, so that a future update through other paths
won't trigger a WARN_ON().
The warning is triggered because the beacon elements in
the hidden BSSes that are children of the BSS should
always be the same as in the parent.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a non-transmitted BSS shares enough information (both
SSID and BSSID!) with another non-transmitted BSS of a
different AP, then we can find and update it, and then
try to add it to the non-transmitted BSS list. We do a
search for it on the transmitted BSS, but if it's not
there (but belongs to another transmitted BSS), the list
gets corrupted.
Since this is an erroneous situation, simply fail the
list insertion in this case and free the non-transmitted
BSS.
This fixes CVE-2022-42721.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are multiple refcounting bugs related to multi-BSSID:
- In bss_ref_get(), if the BSS has a hidden_beacon_bss, then
the bss pointer is overwritten before checking for the
transmitted BSS, which is clearly wrong. Fix this by using
the bss_from_pub() macro.
- In cfg80211_bss_update() we copy the transmitted_bss pointer
from tmp into new, but then if we release new, we'll unref
it erroneously. We already set the pointer and ref it, but
need to NULL it since it was copied from the tmp data.
- In cfg80211_inform_single_bss_data(), if adding to the non-
transmitted list fails, we unlink the BSS and yet still we
return it, but this results in returning an entry without
a reference. We shouldn't return it anyway if it was broken
enough to not get added there.
This fixes CVE-2022-42720.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: a3584f56de ("cfg80211: Properly track transmitting and non-transmitting BSS")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When iterating the elements here, ensure the length byte is
present before checking it to see if the entire element will
fit into the buffer.
Longer term, we should rewrite this code using the type-safe
element iteration macros that check all of this.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Reported-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Per spec, the maximum value for the MaxBSSID ('n') indicator is 8,
and the minimum is 1 since a multiple BSSID set with just one BSSID
doesn't make sense (the # of BSSIDs is limited by 2^n).
Limit this in the parsing in both cfg80211 and mac80211, rejecting
any elements with an invalid value.
This fixes potentially bad shifts in the processing of these inside
the cfg80211_gen_new_bssid() function later.
I found this during the investigation of CVE-2022-41674 fixed by the
previous patch.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Fixes: 78ac51f815 ("mac80211: support multi-bssid")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the copy code of the elements, we do the following calculation
to reach the end of the MBSSID element:
/* copy the IEs after MBSSID */
cpy_len = mbssid[1] + 2;
This looks fine, however, cpy_len is a u8, the same as mbssid[1],
so the addition of two can overflow. In this case the subsequent
memcpy() will overflow the allocated buffer, since it copies 256
bytes too much due to the way the allocation and memcpy() sizes
are calculated.
Fix this by using size_t for the cpy_len variable.
This fixes CVE-2022-41674.
Reported-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Tested-by: Soenke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on changes in the specification the TBTT information in
the RNR can include MLD information, so update the parsing to
allow extracting the short SSID information in such a case.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When retrieving the S1G channel number from IEs, we should retrieve
the operating channel instead of the primary channel. The S1G operation
element specifies the main channel of operation as the oper channel,
unlike for HT and HE which specify their main channel of operation as
the primary channel.
Signed-off-by: Kieran Frewen <kieran.frewen@morsemicro.com>
Signed-off-by: Bassem Dawood <bassem@morsemicro.com>
Link: https://lore.kernel.org/r/20220420041321.3788789-1-kieran.frewen@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Synchronize additions to nontrans_list of transmitting BSS with
bss_lock to avoid races. Also when cfg80211_add_nontrans_list() fails
__cfg80211_unlink_bss() needs bss_lock to be held (has lockdep assert
on bss_lock). So protect the whole block with bss_lock to avoid
races and warnings. Found during code review.
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1649668071-9370-1-git-send-email-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When adding 6GHz channels to scan request based on reported
co-located APs, don't add channels that have only APs with
"non-transmitted" BSSes if they only match the wildcard SSID since
they will be found by probing the "transmitted" BSS.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.f6ddf099f934.I231e55885d3644f292d00dfe0f42653269f2559e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A non-collocated AP whose primary channel is not a PSC channel
may transmit a duplicated beacon on the corresponding PSC channel
in which it would indicate its true primary channel.
Use this inforamtion contained in the HE operation IE to determine
the primary channel of the AP.
In case of invalid infomration ignore it and use the channel
the frame was received on.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211202143322.71eb2176e54e.I130f678e4aa390973ab39d838bbfe7b2d54bff8e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When kzalloc failed and rdev->sacn_req or rdev->scan_msg is null, pass a
null pointer to kfree is redundant, delete it and return directly.
Signed-off-by: liuguoqiang <liuguoqiang@uniontech.com>
Link: https://lore.kernel.org/r/20211115092139.24407-1-liuguoqiang@uniontech.com
[remove now unused creq = NULL assigment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get channel number from ies is a common logic, so separate it to a new
function, which could also be used by lower driver.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/20210930081533.4898-1-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 'if (dev)' statement already move into dev_{put , hold}, so remove
redundant if statements.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we exceed the limit of BSS entries, this function will free the
new entry, however, at this time, it is the last door to access the
inputed ies, so these ies will be unreferenced objects and cause memory
leak.
Therefore we should free its ies before deallocating the new entry, beside
of dropping it from hidden_list.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210628132334.851095-1-phind.uet@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To discover a hidden AP on the 6GHz band, the probe request
sent to the AP needs to include the AP's SSID, as some APs
would not respond with a probe response based only on short
SSID match.
To support hidden AP discovery over the 6GHz band,
when constructing the specific 6GHz band scan also include
SSIDs that were part of the original scan request, so these
can be used in the probe requests transmitted during scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.218df9d3203c.Ice0f7a2f6a65f1f9710b7898591481baeefaf490@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "ap_info->tbtt_info_len" and "length" variables are the same value
but it is confusing how the names are mixed up. Let's use "length"
everywhere for consistency.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YJaMNzZENkYFAYQX@mwanda
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
-----BEGIN PGP SIGNATURE-----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=b0NQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of updates, all over the map:
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of scan request with wildcard SSID, or in case of more
than one SSID in scan request, need to scan PSC channels even though
all the co-located APs found during the legacy bands scan indicated
that all the APs in their ESS are co-located, as we might find different
networks on the PSC channels.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201129172929.736415a9ca5d.If5b3578ae85e11a707a5da07e66ba85928ba702c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The for-loop iterates with a u8 loop counter and compares this
with the loop upper limit of request->n_ssids which is an int type.
There is a potential infinite loop if n_ssids is larger than the
u8 loop counter, so fix this by making the loop counter an int.
Addresses-Coverity: ("Infinite loop")
Fixes: c8cb5b854b ("nl80211/cfg80211: support 6 GHz scanning")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201029222407.390218-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The S1G beacon is an extension frame as opposed to
management frame for the regular beacon. This means we may
have to occasionally cast the frame buffer to a different
header type. Luckily this isn't too bad as scan results
mostly only care about the IEs.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-6-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support 6 GHz scanning, by
* a new scan flag to scan for colocated BSSes advertised
by (and found) APs on 2.4 & 5 GHz
* doing the necessary reduced neighbor report parsing for
this, to find them
* adding the ability to split the scan request in case the
device by itself cannot support this.
Also add some necessary bits in mac80211 to not break with
these changes.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200918113313.232917c93af9.Ida22f0212f9122f47094d81659e879a50434a6a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The low level driver adds its own opaque information
in the BSS table in the cfg80211_bss structure.
The low level driver may need to signal that this information
is no longer relevant and needs to be recreated.
Add an API to allow the low level driver to do that.
iwlwifi needs this because it keeps there an information about
the firmware's internal clock. This is kept in mac80211's
struct ieee80211_bss::sync_device_ts.
This information is populated while we scan, we add the
internal firmware's clock to each beacon which allows us to
program the firmware correctly after association so that
it'll know when (in terms of its internal clock) the DTIM
and TBTT will happen.
When the firmware is reset this internal clock is reset as
well and ieee80211_bss::sync_device_ts is no longer accurate.
iwlwifi will call this new API any time the firmware is started.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20200625111524.3992-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some bands (S1G) define channels centered on a non-integer
MHz. Give ieee80211_channel and cfg80211_chan_def a
freq_offset component where the final frequency can be
expressed as:
MHZ_TO_KHZ(chan->center_freq) + chan->freq_offset;
Also provide some helper functions to do the frequency
conversion and test for equality.
Retain the existing interface to frequency and channel
conversion helpers, and expose new ones which handle
frequencies in units of KHz.
Some internal functions (net/wireless/chan.c) pass around
a frequency value. Convert these to units of KHz.
mesh, ibss, wext, etc. are currently ignored.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
