While debugging Haswell link train failures I observed that we never
try the maximum voltage configuration more than once consecutively. We
start the training, the monitor keeps telling us to increase the
voltage, then when we reach the maximum we just go back to the start
(because of the "memset" above "voltage_tries = 0"). When we reach
this point, we keep alternating between the maximum and the minimum
voltages until we give up.
The DP spec suggests that we should try the same voltage 5 times
before giving up. This patch makes us try the maximum voltage at
least 5 times before going back to the minimum voltages.
This patch does not fix any particular bug I'm aware of.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The passed mode must not be modified by the operation, make it const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We already have this pattern at quite a few places, and moving part of
the modeset helper stuff into the driver will add more.
v2: Don't clobber the crtc struct name with the macro parameter ...
v3: Convert two more places noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
High frequency link configurations have the potential to cause trouble
with long and/or cheap cables, so prefer slow and wide configurations
instead. This patch has the potential to cause trouble for eDP
configurations that lie about available lanes, so if we run into that we
can make it conditional on eDP.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45801
Tested-by: peter@colberg.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into drm-intel-next-queued
I want to merge the "no more fake agp on gen6+" patches into
drm-intel-next (well, the last pieces). But a patch in 3.5-rc4 also
adds a new use of dev->agp. Hence the backmarge to sort this out, for
otherwise drm-intel-next merged into Linus' tree would conflict in the
relevant code, things would compile but nicely OOPS at driver load :(
Conflicts in this merge are just simple cases of "both branches
changed/added lines at the same place". The only tricky part is to
keep the order correct wrt the unwind code in case of errors in
intel_ringbuffer.c (and the MI_DISPLAY_FLIP #defines in i915_reg.h
together, obviously).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_ringbuffer.c
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They aren't going anywhere, and probing on DDC can cause the panel to
blank briefly, so read them up front and cache them for later queries.
v2: fix potential NULL derefs in intel_dp_get_edid_modes and
intel_dp_get_edid (Jani)
copy full EDID length, including extension blocks (Takashi)
free EDID on teardown (Takashi)
v3: malloc a new EDID buffer that's big enough for the memcpy (Chris)
v4: change handling of NULL EDIDs, just preserve the NULL behavior
across detects and mode list fetches rather than trying to re-fetch
the EDID (Chris)
v5: be glad that Chris is around to remind me to hit C-x C-s before
committing.
References: https://bugs.freedesktop.org/show_bug.cgi?id=46856
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 092945e11c.
This commit prevents a DP screen from properly training the link.
Oddly enough it works, once the machine has been warm-booted with an
older kernel.
According to DP docs this _should_ have been the right precharge time.
Also, the commit that originally introduces this was just general snb
DP enabling and didn't mention any specific reason for this special
value. Whatever, trust the reporter that this makes things worse and
let's just revert it.
v2: Less spelling fail.
Cc: Adam Jackson <ajax@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reported-by: "Wouter M. Koolen" <W.M.Koolen-Wijkstra@cwi.nl>
Buglink: https://lkml.org/lkml/2012/6/14/301
Cc: stable@vger.kernel.org (only for 3.4)
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The new oui probe has been missing these.
This issue has been introduce in
commit 0d19832853
Author: Adam Jackson <ajax@redhat.com>
Date: Mon May 14 16:05:47 2012 -0400
drm/i915/dp: Probe branch/sink OUIs
v2: Do the eDP vdd dance of simply not probing the OUI on eDP panels
as suggested by Chris Wilson.
v3: Fix up the error path fail - I suck.
Cc: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50808
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Bugreport: http://permalink.gmane.org/gmane.comp.video.dri.devel/69695
Tested-by: Yang Guang <guang.a.yang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should only frob adjusted_mode. This is in preparation of
a massive patch by Laurent Pinchart to make the mode argument
const.
After the previous two prep patches the only thing left is to clean up
things a bit. I've opted to pass in an adjust_mode param to
dp_adjust_dithering because that way we can be sure to avoid
duplicating this logic between mode_valid and mode_fixup - which was
the cause behind a dp link bw calculation bug in the past.
Also mark the mode argument of pch_panel_fitting const.
v2: Split up the mode->clock => adjusted_mode->clock change,
as suggested by Chris Wilson.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of changing mode->clock, which we should leave as-is.
After the previous patch we only touch that if it's a panel, and then
adjusted mode->clock equals adjusted_mode->clock. Outside of
intel_dp.c we only use ajusted_mode->clock in the mode_set functions.
Within intel_dp.c we only use it to calculate the dp dithering
and link bw parameters, so that's the only thing we need to fix
up.
As a temporary ugliness (until the cleanup in the next patch) we
pass the adjusted_mode into dp_dither for both parameters (because
that one still looks at mode->clock).
Note that we do overwrite adjusted_mode->clock with the selected dp
link clock, but that only happens after we've calculated everything we
need based on the dotclock of the adjusted output configuration.
Outside of intel_dp.c only intel_display.c uses adjusted_mode->clock,
and that stays the same after this patch (still equals the selected dp
link clock). intel_display.c also needs the actual dotclock (as
target_clock), but that has been fixed up in the previous patch.
v2: Adjust the debug message to also use adjusted_mode->clock.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of abusing mode->clock by storing it in there - we
shouldn't touch that one at all. This patch is the first prep step to
constify the mode argument of the intel_dp_mode_fixup function.
The next patch will stop us from modifying mode->clock.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of checking for !CPT, check for IBX to make it clearer that
this is a IBX-specific workaround. No functional change because we
smash the PPT PCH into the HAS_PCH_CPT check and atm DP isn't enabled
on the haswell LPT PCH yet.
See Bspec Vol 3, Part 3, Section 4.[3-5].1 about DP[BCD], bit 30 for
details of this workaround.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need the latest dma-buf code from Dave Airlie so that we can pimp
the backing storage handling code in drm/i915 with Chris Wilson's
unbound tracking and stolen mem backed gem object code.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: tune down the noise of the RP irq limit fail
drm/i915: Remove the error message for unbinding pinned buffers
drm/i915: Limit page allocations to lowmem (dma32) for i965
drm/i915: always use RPNSWREQ for turbo change requests
drm/i915: reject doubleclocked cea modes on dp
drm/i915: Adding TV Out Missing modes.
drm/i915: wait for a vblank to pass after tv detect
drm/i915: no lvds quirk for HP t5740e Thin Client
drm/i915: enable vdd when switching off the eDP panel
drm/i915: Fix PCH PLL assertions to not assume CRTC:PLL relationship
drm/i915: Always update RPS interrupts thresholds along with frequency
drm/i915: properly handle interlaced bit for sdvo dtd conversion
drm/i915: fix module unload since error_state rework
drm/i915: be more careful when returning -ENXIO in gmbus transfer
These are ultra-low-res modes used to upscale SDTV content and we
don't know how to support these on dp on intel hw:
- It's unclear whether we can send avi infoframes over dp ports.
- And the pixel repeat setting that work for hdmi/sdvo explicitly
don't work for dp.
So don't bother and just reject these modes. These modes have been
introduced in
commit 54ac76f851
Author: Christian Schmidt <schmidt@digadd.de>
Date: Mon Dec 19 14:53:16 2011 +0000
drm/edid: support CEA video modes.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45729
Tested-by: Yuang Guang <guang.a.yang@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have one bug report from a validation team that we get the eDP
panel sequencing still somewhat wrong: We need to enable VDD while
switching off the panel and backlight. Unfortunately that reporter
seems to have fallen off the earth :(
For another reporter this actually fixes a black panel issue because
without this the backlight/panel gets confused and doesn't light up
again.
v2: I've forgotten to remove the vdd_off call in panel_off which is
now bogus. This essentially reverts
commit 17038de5f1
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 16 22:43:42 2012 +0100
drm/i915/dp: Flush any outstanding work to turn the VDD off
v3: the current panel_off code forces off the vdd power, too. Which is
bogus and resulted in some funny warnings later on when we've tried to
do aux channel communications with just the vdd forced on. Fix this,
too.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46312
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43163
Tested-by: Vincent Frentzel <zcecc22@gmail.com>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The status bits corresponding to the interrupt enable bits are the
"live" hotplug status bits, and reflect the current status of the port
(high for a detected connection, low for a disconnect). The actual bits
corresponding to the interrupt source are elsewhere. The actual event is
then determined by a combination of the interrupt flag and the current
live status (if the interrupt is active, but the current status is not,
then we have detected a disconnect.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PCH PLLs aren't required for outputs on the CPU, so we shouldn't just
treat them as part of the pipe.
So split the code out and manage PCH PLLs separately, allocating them
when needed or trying to re-use existing PCH PLL setups when the timings
match.
v2: add num_pch_pll field to dev_priv (Daniel)
don't NULL the pch_pll pointer in disable or DPMS will fail (Jesse)
put register offsets in pll struct (Chris)
v3: Decouple enable/disable of PLLs from get/put.
v4: Track temporary PLL disabling during modeset
v5: Tidy PLL initialisation by only checking for num_pch_pll == 0 (Eugeni)
v6: Avoid mishandling allocation failure by embedding the small array of
PLLs into the device struct
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44309
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (up to v2)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v3+)
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pretty useful to debug our DP bandwidth woes.
v2: Also print out the required and available link bandwidth,
suggested by Chris Wilson.
v3: Also print out the input parameters so that diagnosing failures to
find a valid dp link configuration is possible.
v4: s/Display port/DP/ to shorten the output.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEbBAABAgAGBQJPi3XOAAoJEHm+PkMAQRiGnsUH9RjHwH4YFVyuP/DKtKa6zs74
wqkpT15yITQ5WWMog4JaJFFg5rJCUd8QZr7AS/HSn0ijDyZX5VU7Rcs9cMudDzNR
H/5K/AscS4fjb0HwWVqoltTWHRb9QGSwVN3+E3VCDLt9P89YJ0o3QztkkuEX5dkZ
jc7reVXTfRnCcILEa9jleOzrn+OLM3j/jAjQ2hGunl8EDLzD4b17HHPoli4jEZ/5
5ibpSVsPD+AqzN+glbXvYjVItl12D0IQos/JdOwfuZriCVWLxysSSwHZTbPCyvBZ
LHH4HR5T+XLSXbjJeNkUFHLzqU+d5gVRadIoWtJCxqxFjKbOs2YtzJ5Ai0nDiw==
=kTkC
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc3' into drm-intel-next-queued
Backmerge Linux 3.4-rc3 into drm-intel-next to resolve a few things
that conflict/depend upon patches in -rc3:
- Second part of the Sandybridge workaround series - it changes some
of the same registers.
- Preparation for Chris Wilson's fencing cleanup - we need the fix
from -rc3 merged before we can move around all that code.
- Resolve the gmbus conflict - gmbus has been disabled in 3.4 again,
but should be enabled on all generations in 3.5.
Conflicts:
drivers/gpu/drm/i915/intel_i2c.c
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we may kick off a delayed workqueue task to switch of the VDD lines, we
need to complete that task prior to turning off the panel (which itself
depends upon VDD being off).
v2: Don't cancel the outstanding work as this may trigger a deadlock
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If these regs don't have valid values, the panel won't come up, and may
even cause a system hang. So do a basic sanity check when an eDP panel
is detected.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44305
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've only computed whether we need to fall back to 6bpc due to dp
link bandwidth constrains in mode_valid, but not mode_fixup. Under
various circumstances X likes to create new modes which then lack
proper 6bpc flags (if required), resulting in mode_fixup failures and
ultimately black screens.
Chris Wilson pointed out that we still get things wrong for bpp > 24,
but that should be fixed in another patch (and it'll be easier because
this patch consolidates the logic).
The likely culprit for this regression is
commit 3d794f87238f74d80e78a7611c7fbde8a54c85c2
Author: Keith Packard <keithp@keithp.com>
Date: Wed Jan 25 08:16:25 2012 -0800
drm/i915: Force explicit bpp selection for intel_dp_link_required
v2: Fix indentation and tune down the too bold claim that this should
fix the world. Both noticed by Chris Wilson.
v3: Try to really git add things.
Reported-and-tested-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48170
Cc: stable@kernel.org
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While fixing up a merge conflict with drm-next I've noticed that we
use the same audio drm connector property also for dp and sdvo
outputs.
So put the new enum to some good use and convert these paths, too. The
HDMI_AUDIO_ prefix is a bit a misnomer. But at least for sdvo it makes
sense (and you can also connect a hdmi monitor with a dp->hdmi cable),
so I've decided to stick with it.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Back-merge from drm-fixes into drm-intel-next to sort out two things:
- interlaced support: -fixes contains a bugfix to correctly clear
interlaced configuration bits in case the bios sets up an interlaced
mode and we want to set up the progressive mode (current kernels
don't support interlaced). The actual feature work to support
interlaced depends upon (and conflicts with) this bugfix.
- forcewake voodoo to workaround missed IRQ issues: -fixes only enabled
this for ivybridge, but some recent bug reports indicate that we
need this on Sandybridge, too. But in a slightly different flavour
and with other fixes and reworks on top. Additionally there are some
forcewake cleanup patches heading to -next that would conflict with
currrent -fixes.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is never correct to use intel_crtc->bpp in intel_dp_link_required,
so instead pass an explicit bpp in to this function. This patch
only supports 18bpp and 24bpp modes, which means that 10bpc modes will
be computed incorrectly. Fixing that will require more extensive
changes, and so must be addressed separately from this bugfix.
intel_dp_link_required is called from intel_dp_mode_valid and
intel_dp_mode_fixup.
* intel_dp_mode_valid is called to list supported modes; in this case,
the current crtc values cannot be relevant as the modes in question
may never be selected. Thus, using intel_crtc->bpp is never right.
* intel_dp_mode_fixup is called during mode setting, but it is run
well before ironlake_crtc_mode_set is called to set intel_crtc->bpp,
so using intel_crtc-bpp in this path can only ever get a stale
value.
Cc: Lubos Kolouch <lubos.kolouch@gmail.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42263
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44881
Tested-by: Dave Airlie <airlied@redhat.com>
Tested-by: camalot@picnicpark.org (Dell Latitude 6510)
Tested-by: Roland Dreier <roland@digitalvampire.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This is paranoid, but I am entirely willing to believe the hardware
could come up with a condition where I get a status with both the 'done'
and 'receive error' bits set.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The default in the Sandybridge docs is 5, as on Ironlake, and I have no
reason to believe 3 would work any better.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Matches the advice in the Sandybridge documentation.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On DP monitor hot remove, clear DP_AUDIO_OUTPUT_ENABLE accordingly,
so that the audio driver will receive hot plug events and take action
to refresh its device state and ELD contents.
Note that the DP_AUDIO_OUTPUT_ENABLE bit may be enabled or disabled
only when the link training is complete and set to "Normal".
Tested OK for both hot plug/remove and DPMS on/off.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Some active adaptors (VGA usually) only have two lanes at 2.7GHz.
That's a maximum pixel clock of 144MHz at 8bpc, but 192MHz at 6bpc.
Fixes Asus UX31 panel being black at startup due to no valid modes since
dc22ee6fc1.
v2: Rebased to current code, resulting in the fix applying to EDP panels as
well. Also changed from spatio-temporal to just spatial dithering on
pre-ironlake, to be conssitent (and less visual flicker)
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The Ivybridge eDP control register looks like a cross between a
Cougarpoint PCH DP control register and a Sandybridge eDP control
register.
Where things trivially match, share the code. Where there are any
tricky bits, just split things out into two obviously separate code paths.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Fang Xun <xunx.fang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41991
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux: (25 commits)
drm/i915: Fix inconsistent backlight level during disabled
drm, i915: Fix memory leak in i915_gem_busy_ioctl().
drm/i915: Use DPCD value for max DP lanes.
drm/i915: Initiate DP link training only on the lanes we'll be using
drm/i915: Remove trailing white space
drm/i915: Try harder during dp pattern 1 link training
drm/i915: Make DP prepare/commit consistent with DP dpms
drm/i915: Let panel power sequencing hardware do its job
drm/i915: Treat PCH eDP like DP in most places
drm/i915: Remove link_status field from intel_dp structure
drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
drm/i915: Module parameters using '-1' as default must be signed type
drm/i915: Turn on another required clock gating bit on gen6.
drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
drm/i915: enable cacheable objects on Ivybridge
drm/i915: add constants to size fence arrays and fields
drm/i915: Ivybridge still has fences!
drm/i915: forcewake warning fixes in debugfs
drm/i915: Fix object refcount leak on mmappable size limit error path.
drm/i915: Use mode_config.mutex in ironlake_panel_vdd_work
...
The BIOS VBT value for an eDP panel has been shown to be incorrect on
one machine, and we haven't found any machines where the DPCD value
was wrong, so we'll use the DPCD value everywhere.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Limit the link training setting command to the lanes needed for the
current mode. It seems vaguely possible that a monitor will try to
train the other lanes and fail in some way, so this seems like the
safer plan.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Instead of going through the sequence just once, run through the whole
set up to 5 times to see if something can work. This isn't part of the
DP spec, but the BIOS seems to do it, and given that link training
failure is so bad, it seems reasonable to follow suit.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make sure the sequence of operations in all three functions makes
sense:
1) The backlight must be off unless the screen is running
2) The link must be running to turn the eDP panel on/off
3) The CPU eDP PLL must be running until everything is off
Signed-off-by: Keith Packard <keithp@keithp.com>
The panel power sequencing hardware tracks the stages of panel power
sequencing and signals when the panel is completely on or off. Instead
of blindly assuming the panel timings will work, poll the panel power
status register until it shows the correct values.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCH eDP has many of the same needs as regular PCH DP connections,
including the DP_CTl bit settings, the TRANS_DP_CTL register.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No persistent data was ever stored here, so link_status is instead
allocated on the stack as needed.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Every usage of PCH_PP_CONTROL sets the PANEL_UNLOCK_REGS value to
ensure that writes will be respected, move this to a common function
to make the driver cleaner.
No functional changes.
Signed-off-by: Keith Packard <keithp@keithp.com>
According to the gen6 docs, only the DP_A port (on-CPU eDP) still uses
the old IBX bit shift for the link training pattern setup bits.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The obvious counterpart to is_pch_edp(). Convert existing instances of
the idiom to the new routine.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
DPCD 1.1+ adds some automated test infrastructure support. Add support
for reading the IRQ source and jumping to a test handling routine if
needed. Subsequent patches will handle particular tests; this patch
just ACKs any requested tests by default.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Read link status first, followed by the full DPCD receiver cap field
rather than just the first 8 bytes.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
