Increase length to be copied to be large enough to overcome the
following compilation error. The buf is large enough for this purpose.
drivers/dma/xilinx/xilinx_dpdma.c: In function ‘xilinx_dpdma_debugfs_desc_done_irq_read’:
drivers/dma/xilinx/xilinx_dpdma.c:313:39: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
313 | snprintf(buf, out_str_len, "%d",
| ^
drivers/dma/xilinx/xilinx_dpdma.c:313:9: note: ‘snprintf’ output between 2 and 6 bytes into a destination of size 5
313 | snprintf(buf, out_str_len, "%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
314 | dpdma_debugfs.xilinx_dpdma_irq_done_count);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20231222094017.731917-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Interleaved DMA functionality allows dmaengine clients' to express
DMA transfers in an arbitrary way. This is extremely useful in FPGA
environments, where a greater transfer flexibility is needed. For
instance, in one FPGA design there may be need to do DMA to/from a FIFO
at a fixed address, and also to do DMA to/from a (non)contiguous RAM
memory.
Introduce separate tx preparation callback and add tx-flags handling
logic. Their behavior is based on the description of interleaved DMA
transfers in both source code and the DMAEngine's documentation.
Since XDMA is a fully-fledged scatter-gather dma engine, the logic of
xdma_prep_interleaved_dma() is fairly simple and similar to the other
tx preparation callbacks. The whole tx-flags handling logic resides in
xdma_channel_isr(). Transfer of a single frame from a interleaved DMA
transfer template is pretty similar to the single sg transaction.
Therefore, the transaction of the whole interleaved DMA transfer
template is basically a cyclic dma transaction with finite cycles/periods
(equal to the frame of count) of a single sg transfers.
Signed-off-by: Jan Kuliga <jankul@alatek.krakow.pl>
Link: https://lore.kernel.org/r/20231218113943.9099-9-jankul@alatek.krakow.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make generic code generic. As descriptor-filling logic stays the same
regardless of a dmaengine's type of transfer, it is possible to write
the descriptor-filling function in a generic way, so that it can be used
for every single type of transfer preparation callback.
Signed-off-by: Jan Kuliga <jankul@alatek.krakow.pl>
Link: https://lore.kernel.org/r/20231218113943.9099-8-jankul@alatek.krakow.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Extend the capability of transfer status reporting. Introduce error flag,
which allows to report error in case of a interrupt-reported error
condition.
Signed-off-by: Jan Kuliga <jankul@alatek.krakow.pl>
Link: https://lore.kernel.org/r/20231218113943.9099-7-jankul@alatek.krakow.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Check and clear the status register value before proceeding any
further in xdma_channel_isr(). It is necessary to do it since the
interrupt may occur on any error condition enabled at the start of a
transfer.
Signed-off-by: Jan Kuliga <jankul@alatek.krakow.pl>
Link: https://lore.kernel.org/r/20231218113943.9099-6-jankul@alatek.krakow.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify xdma_xfer_stop(). Stop the dma engine and clear its status
register unconditionally - just do what its name states. This change
also allows to call it without grabbing a lock, which minimizes
the total time spent with a spinlock held.
Delete the currently processed vd.node from the vc.desc_issued list
prior to passing it to vchan_terminate_vdesc(). In case there's more
than one descriptor pending on vc.desc_issued list, calling
vchan_terminate_desc() results in losing the link between
vc.desc_issued list head and the second descriptor on the list. Doing so
results in resources leakege, as vchan_dma_desc_free_list() won't be
able to properly free memory resources attached to descriptors,
resulting in dma_pool_destroy() failure.
Don't call vchan_dma_desc_free_list() from within xdma_terminate_all().
Move all terminated descriptors to the vc.desc_terminated list instead.
This allows to postpone freeing memory resources associated with
descriptors until the call to vchan_synchronize(), which is called from
xdma_synchronize() callback. This is the right way to do it -
xdma_terminate_all() should return as soon as possible, while freeing
resources (that may be time consuming in case of large number of
descriptors) can be done safely later.
Fixes: f5c392d106 ("dmaengine: xilinx: xdma: Add terminate_all/synchronize callbacks")
Signed-off-by: Jan Kuliga <jankul@alatek.krakow.pl>
Link: https://lore.kernel.org/r/20231218113943.9099-5-jankul@alatek.krakow.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to the XDMA datasheet (PG195), the address of any descriptor
must be 32 byte aligned. The datasheet also states that a contiguous
block of descriptors must not cross a 4k address boundary. Therefore,
it is possible to ease the pressure put on the dma_pool allocator
just by requiring sufficient alignment and boundary values. Add proper
macro definition and change the values passed into the
dma_pool_create().
Signed-off-by: Jan Kuliga <jankul@alatek.krakow.pl>
Link: https://lore.kernel.org/r/20231218113943.9099-4-jankul@alatek.krakow.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Get rid of duplicated macro definitions, as these macros are defined
earlier in the file. Also, get rid of unused member
of 'struct xdma_desc'.
Signed-off-by: Jan Kuliga <jankul@alatek.krakow.pl>
Link: https://lore.kernel.org/r/20231218113943.9099-2-jankul@alatek.krakow.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver is capable of starting scatter-gather transfers and needs to
wait until their end. It is also capable of starting cyclic transfers
and will only be "reset" next time the channel will be reused. In
practice most of the time we hear no audio glitch because the sound card
stops the flow on its side so the DMA transfers are just
discarded. There are however some cases (when playing a bit with a
number of frames and with a discontinuous sound file) when the sound
card seems to be slightly too slow at stopping the flow, leading to a
glitch that can be heard.
In all cases, we need to earn better control of the DMA engine and
adding proper ->device_terminate_all() and ->device_synchronize()
callbacks feels totally relevant. With these two callbacks, no glitch
can be heard anymore.
Fixes: cd8c732ce1 ("dmaengine: xilinx: xdma: Support cyclic transfers")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://lore.kernel.org/r/20231130111315.729430-5-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver internal scatter-gather logic is:
* set busy to true
* start transfer
<irq>
* set busy to false
* trigger next transfer if any
* set busy to true
</irq>
Setting busy to false in cyclic transfers does not make any sense and is
conceptually wrong. In order to ease the integration of additional
callbacks let's move this change to the scatter-gather path.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231130111315.729430-4-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We support both modes, but they perform totally different taks in the
interrupt handler. Clarify what shall be done in each case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231130111315.729430-3-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Xilinx DMA engine is capable of keeping track of the number of elapsed
periods and this is an increasing 32-bit counter which is only reset
when turning off the engine. No need to add this value to our local
counter.
Fixes: cd8c732ce1 ("dmaengine: xilinx: xdma: Support cyclic transfers")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231130111315.729430-2-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit cc99582d46 ("dmaengine: xilinx: xilinx_dma: Convert to
platform remove callback returning void") xilinx_dma_remove() doesn't
return zero any more. As the function has no return value any more, just
drop the statement about the return value.
Reported-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231014211656.1512016-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In order to use this dmaengine with sound devices, let's add cyclic
transfers support. Most of the code is reused from the existing
scatter-gather implementation, only the final linking between
descriptors, the control fields (to trigger interrupts more often) and
the interrupt handling are really different.
This controller supports up to 32 adjacent descriptors, we assume this
is way more than enough for the purpose of cyclic transfers and limit to
32 the number of cycled descriptors. This way, we simplify a lot the
overall handling of the descriptors.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231005160237.2804238-4-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In order to reduce and clarify the diff when introducing cyclic
transfers support, let's first prepare the driver a bit. There is no
functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231005160237.2804238-3-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is a warning reported by coccinelle:
./drivers/dma/xilinx/xdma.c:888:22-25: ERROR:
Missing resource_size with res
Use resource_size() on resource object instead of explicit computation.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230803033235.3049137-1-lizetao1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919133207.1400430-60-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919133207.1400430-59-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919133207.1400430-58-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919133207.1400430-57-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New support:
- Qualcomm SM6115 and QCM2290 dmaengine support
- at_xdma support for microchip,sam9x7 controller
Updates:
- idxd updates for wq simplification and ats knob updates
- fsl edma updates for v3 support
- Xilinx AXI4-Stream control support
- Yaml conversion for bcm dma binding
-----BEGIN PGP SIGNATURE-----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=LPWk
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New controller support and updates to drivers.
New support:
- Qualcomm SM6115 and QCM2290 dmaengine support
- at_xdma support for microchip,sam9x7 controller
Updates:
- idxd updates for wq simplification and ats knob updates
- fsl edma updates for v3 support
- Xilinx AXI4-Stream control support
- Yaml conversion for bcm dma binding"
* tag 'dmaengine-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (53 commits)
dmaengine: fsl-edma: integrate v3 support
dt-bindings: fsl-dma: fsl-edma: add edma3 compatible string
dmaengine: fsl-edma: move tcd into struct fsl_dma_chan
dmaengine: fsl-edma: refactor chan_name setup and safety
dmaengine: fsl-edma: move clearing of register interrupt into setup_irq function
dmaengine: fsl-edma: refactor using devm_clk_get_enabled
dmaengine: fsl-edma: simply ATTR_DSIZE and ATTR_SSIZE by using ffs()
dmaengine: fsl-edma: move common IRQ handler to common.c
dmaengine: fsl-edma: Remove enum edma_version
dmaengine: fsl-edma: transition from bool fields to bitmask flags in drvdata
dmaengine: fsl-edma: clean up EXPORT_SYMBOL_GPL in fsl-edma-common.c
dmaengine: fsl-edma: fix build error when arch is s390
dmaengine: idxd: Fix issues with PRS disable sysfs knob
dmaengine: idxd: Allow ATS disable update only for configurable devices
dmaengine: xilinx_dma: Program interrupt delay timeout
dmaengine: xilinx_dma: Use tasklet_hi_schedule for timing critical usecase
dmaengine: xilinx_dma: Freeup active list based on descriptor completion bit
dmaengine: xilinx_dma: Increase AXI DMA transaction segment count
dmaengine: xilinx_dma: Pass AXI4-Stream control words to dma client
dt-bindings: dmaengine: xilinx_dma: Add xlnx,irq-delay property
...
Program IRQDelay for AXI DMA. The interrupt timeout mechanism causes
the DMA engine to generate an interrupt after the delay time period
has expired. It enables dmaengine to respond in real-time even though
interrupt coalescing is configured. It also remove the placeholder
for delay interrupt and merge it with frame completion interrupt.
Since by default interrupt delay timeout is disabled this feature
addition has no functional impact on VDMA, MCDMA and CDMA IP's.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1691387509-2113129-8-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
AXIDMA IP in SG mode sets completion bit to 1 when the transfer is
completed. Read this bit to move descriptor from active list to the
done list. This feature is needed when interrupt delay timeout and
IRQThreshold is enabled i.e Dly_IrqEn is triggered w/o completing
interrupt threshold.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1691387509-2113129-6-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Increase AXI DMA transaction segments count to ensure that even in
high load we always get a free segment in prepare descriptor for a
DMA_SLAVE transaction.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1691387509-2113129-5-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Read DT property to check if AXI DMA is connected to streaming IP
i.e axiethernet. If connected i.e xlnx,axistream-connected property
is present in the dma node then pass AXI4-Stream control words to dma
client using metadata_ops dmaengine API.
If not connected then driver won't support metadata_ops dmaengine API
and continue to support all legacy usecases.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1691387509-2113129-4-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A couple of hardware registers need to be set to reflect which
interrupts have been allocated to the device. Each register is 32-bit
wide and can receive four 8-bit values. If we provide any other interrupt
number than four, the irq_num variable will never be 0 within the while
check and the while block will loop forever.
There is an easy way to prevent this: just break the for loop
when we reach "irq_num == 0", which anyway means all interrupts have
been processed.
Cc: stable@vger.kernel.org
Fixes: 17ce252266 ("dmaengine: xilinx: xdma: Add xilinx xdma driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://lore.kernel.org/r/20230731101442.792514-2-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143138.1066177-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New support:
- Apple admac t8112 device support
- StarFive JH7110 DMA controller
Updates:
- Big pile of idxd updates to support IAA 2.0 device capabilities, DSA
2.0 Event Log and completion record faulting features and new DSA
operations
- at_xdmac supend & resume updates and driver code cleanup
- k3-udma supend & resume support
- k3-psil thread support for J784s4
-----BEGIN PGP SIGNATURE-----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=Vqrw
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New support:
- Apple admac t8112 device support
- StarFive JH7110 DMA controller
Updates:
- Big pile of idxd updates to support IAA 2.0 device capabilities,
DSA 2.0 Event Log and completion record faulting features and
new DSA operations
- at_xdmac supend & resume updates and driver code cleanup
- k3-udma supend & resume support
- k3-psil thread support for J784s4"
* tag 'dmaengine-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (57 commits)
dmaengine: idxd: add per wq PRS disable
dmaengine: idxd: add pid to exported sysfs attribute for opened file
dmaengine: idxd: expose fault counters to sysfs
dmaengine: idxd: add a device to represent the file opened
dmaengine: idxd: add per file user counters for completion record faults
dmaengine: idxd: process batch descriptor completion record faults
dmaengine: idxd: add descs_completed field for completion record
dmaengine: idxd: process user page faults for completion record
dmaengine: idxd: add idxd_copy_cr() to copy user completion record during page fault handling
dmaengine: idxd: create kmem cache for event log fault items
dmaengine: idxd: add per DSA wq workqueue for processing cr faults
dmanegine: idxd: add debugfs for event log dump
dmaengine: idxd: add interrupt handling for event log
dmaengine: idxd: setup event log configuration
dmaengine: idxd: add event log size sysfs attribute
dmaengine: idxd: make misc interrupt one shot
dt-bindings: dma: snps,dw-axi-dmac: constrain the items of resets for JH7110 dma
dt-bindings: dma: Drop unneeded quotes
dmaengine: at_xdmac: align declaration of ret with the rest of variables
dmaengine: at_xdmac: add a warning message regarding for unpaused channels
...
Align ZDMA DMA as well as coherent memory masks to 44 bit. This is
required when using >32 bit memory regions.
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230316093318.6722-1-harini.katakam@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make the description of @xdma_chan to @xchan to silence the warnings:
drivers/dma/xilinx/xdma.c:283: warning: Function parameter or member 'xchan' not described in 'xdma_xfer_start'
drivers/dma/xilinx/xdma.c:283: warning: Excess function parameter 'xdma_chan' description in 'xdma_xfer_start'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4051
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20230214010344.5354-1-yang.lee@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New support:
- TI AM62Ax controller support
- Xilinx xdma driver
- Qualcomm SM6125, SM8550, QDU1000/QRU1000 GPI controller
Updates:
- Runtime pm support for at_xdmac driver
- IMX sdma binding conversion to yaml and HDMI audio support
- IMX mxs binding conversion to yaml
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+vs47OPLdNbVcHzyfBQHDyUjg0cFAmP4uMkACgkQfBQHDyUj
g0fXvhAAstzwh2KirInbEleqmH7PnjMrWut2F8oTCeFJjPUXRKx3HtXW5JyDLeT4
6iXhEknWnkvbbEQf1EwZNfK4xC+xNvEU7XvNdhm23kyXqYJBRwiq5cjqapLLr9Vf
XDRRZ1CK/Zhxqhk0kuOnQIsGLciAVFcXhoswjzlnaGL4yGLkZcWB8bmO1JOzITi8
GqQD9wx+dEixSg3004qbE8GceC4TGq375fFiHVTiNO878pKK+vQF9DxsEabchrIK
8HPCF8jVZ0A+6gDYysJMjn81cPK6AdnbIhJnvfaF7N3fdl2QUDSweM9NbF/06B2B
E5G/NOrWe5NrSWoJbXz9U5t7Cg3pZktreLjUlREM2/i+jmqyUC3FMICQYpUneAnk
aUSr2hRBYlbIEJZJhmSMczUfUOqdPFt5mY2bUwvtSfCKf1we5wl9oiC72IvRthmL
hSCs6RQxczM62u7ocjH/T9j2n3zy+vcxijCuIac2Y6FEHaURq/7wcfDypePg37zi
Kf7awaRHE0WOiXj1kc+fsEhkEJ+xEjxiJnCMzFb9jG1A0RBgtsNq6HXCgmd2O/R7
b2Q7hUt3rr9qr4uHTGz0Ure+nkVB7Zz0eCVfNQQ3ypw2DibGc1WhjzpGiEq0tlYK
20wKtbWIFy/MFjIOiZiQTGL2vGnDgjq4DRZgtPKdz60uCGgrM6s=
=xtfI
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"A new driver, couple of device support and binding conversion along
with bunch of driver updates are the main features of this.
New hardware support:
- TI AM62Ax controller support
- Xilinx xdma driver
- Qualcomm SM6125, SM8550, QDU1000/QRU1000 GPI controller
Updates:
- Runtime pm support for at_xdmac driver
- IMX sdma binding conversion to yaml and HDMI audio support
- IMX mxs binding conversion to yaml"
* tag 'dmaengine-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (35 commits)
dmaengine: idma64: Update bytes_transferred field
dmaengine: imx-sdma: Set DMA channel to be private
dmaengine: dw: Move check for paused channel to dwc_get_residue()
dmaengine: ptdma: check for null desc before calling pt_cmd_callback
dmaengine: dw-axi-dmac: Do not dereference NULL structure
dmaengine: idxd: Fix default allowed read buffers value in group
dmaengine: sf-pdma: pdma_desc memory leak fix
dmaengine: Simplify dmaenginem_async_device_register() function
dmaengine: use sysfs_emit() to instead of scnprintf()
dmaengine: Make an order in struct dma_device definition
dt-bindings: dma: cleanup examples - indentation, lowercase hex
dt-bindings: dma: drop unneeded quotes
dmaengine: xilinx: xdma: Add user logic interrupt support
dmaengine: xilinx: xdma: Add xilinx xdma driver
dmaengine: drivers: Use devm_platform_ioremap_resource()
dmaengine: at_xdmac: remove empty line
dmaengine: at_xdmac: add runtime pm support
dmaengine: at_xdmac: align properly function members
dmaengine: ppc4xx: Convert to use sysfs_emit()/sysfs_emit_at() APIs
dmaengine: sun6i: Set the maximum segment size
...
The Xilinx DMA/Bridge Subsystem for PCIe (XDMA) provides up to 16 user
interrupt wires to user logic that generate interrupts to the host.
This patch adds APIs to enable/disable user logic interrupt for a given
interrupt wire index.
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Signed-off-by: Sonal Santan <sonal.santan@amd.com>
Signed-off-by: Max Zhen <max.zhen@amd.com>
Signed-off-by: Brian Xu <brian.xu@amd.com>
Tested-by: Martin Tuma <tumic@gpxsee.org>
Link: https://lore.kernel.org/r/1674145926-29449-3-git-send-email-lizhi.hou@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add driver to enable PCIe board which uses XDMA (the DMA/Bridge Subsystem
for PCI Express). For example, Xilinx Alveo PCIe devices.
https://www.xilinx.com/products/boards-and-kits/alveo.html
The XDMA engine support up to 4 Host to Card (H2C) and 4 Card to Host (C2H)
channels. Memory transfers are specified on a per-channel basis in
descriptor linked lists, which the DMA fetches from host memory and
processes. Events such as descriptor completion and errors are signaled
using interrupts. The hardware detail is provided by
https://docs.xilinx.com/r/en-US/pg195-pcie-dma/Introduction
This driver implements dmaengine APIs.
- probe the available DMA channels
- use dma_slave_map for channel lookup
- use virtual channel to manage dmaengine tx descriptors
- implement device_prep_slave_sg callback to handle host scatter gather
list
- implement device_config to config device address for DMA transfer
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Signed-off-by: Sonal Santan <sonal.santan@amd.com>
Signed-off-by: Max Zhen <max.zhen@amd.com>
Signed-off-by: Brian Xu <brian.xu@amd.com>
Tested-by: Martin Tuma <tumic@gpxsee.org>
Link: https://lore.kernel.org/r/1674145926-29449-2-git-send-email-lizhi.hou@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
platform_get_resource() and devm_ioremap_resource() are wrapped up in the
devm_platform_ioremap_resource() helper. Use the helper and get rid of the
local variable for struct resource *. We now have a function call less.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20221110152528.7821-1-tudor.ambarus@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since for_each_child_of_node() will increase the refcount of node, we need
to call of_node_put() manually when breaking out of the iteration.
Fixes: 9cd4360de6 ("dma: Add Xilinx AXI Video Direct Memory Access Engine driver support")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20221122021612.1908866-1-liushixin2@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New Support:
- AngeloGioacchino Del Regno added support for MT6795 SoC dma controller
- Christian Marangi updated qcom-adm controller binding to yaml
- Geert Uytterhoeven added yaml binding for Renesas r8a779g0 dma controller
- Luca Weiss added support for Qualcomm SM6350 GPI dma controller
Updates:
- Amelie Delaunay provided STM32 DMA-MDMA chaining support
- Andy Shevchenko updated hsu driver to use managed resources
- Dave Jiang & Jerry Snitselaar provided usual round of idxd driver updates
- Janne Grunau & Martin Povišer updated apple dma driver for iommu and pd
properties and removed use of devres for irqs
- Swati Agarwal added device_synchronize support for Xilinx zynqmp driver
-----BEGIN PGP SIGNATURE-----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=zRon
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New Support:
- MT6795 SoC dma controller (AngeloGioacchino Del Regno)
- qcom-adm controller yaml binding (Christian Marangi)
- Renesas r8a779g0 dma controller yaml binding (Geert Uytterhoeven)
- Qualcomm SM6350 GPI dma controller (Luca Weiss)
Updates:
- STM32 DMA-MDMA chaining support (Amelie Delaunay)
- make hsu driver use managed resources (Andy Shevchenko)
- the usual round of idxd driver updates (Dave Jiang & Jerry
Snitselaar)
- apple dma driver iommu and pd properties and remove use
of devres for irqs (Janne Grunau & Martin Povišer)
- device_synchronize support for Xilinx zynqmp driver (Swati
Agarwal)"
* tag 'dmaengine-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (60 commits)
dmaengine: ioat: remove unused declarations in dma.h
dmaengine: ti: k3-udma: Respond TX done if DMA_PREP_INTERRUPT is not requested
dmaengine: zynqmp_dma: Add device_synchronize support
dt-bindings: dma: add additional pbus reset to qcom,adm
dt-bindings: dma: rework qcom,adm Documentation to yaml schema
dt-bindings: dma: apple,admac: Add iommus and power-domains properties
dmaengine: dw-edma: Remove runtime PM support
dmaengine: idxd: add configuration for concurrent batch descriptor processing
dmaengine: idxd: add configuration for concurrent work descriptor processing
dmaengine: idxd: add WQ operation cap restriction support
dmanegine: idxd: reformat opcap output to match bitmap_parse() input
dmaengine: idxd: convert ats_dis to a wq flag
dmaengine: ioat: stop mod_timer from resurrecting deleted timer in __cleanup()
dmaengine: qcom-adm: fix wrong calling convention for prep_slave_sg
dmaengine: qcom-adm: fix wrong sizeof config in slave_config
dmaengine: ti: k3-psil: add additional TX threads for j721e
dmaengine: ti: k3-psil: add additional TX threads for j7200
dmaengine: apple-admac: Trigger shared reset
dmaengine: apple-admac: Do not use devres for IRQs
dmaengine: ti: edma: Remove some unused functions
...
dmaengine_synchronize implementation is required to synchronize proper
termination of current transfers so that any memory resources are not freed
while still in use.
Implement this callback in the driver so that framework can use the same
(in dmaengine_terminate_sync/ dmaengine_synchronize).
Signed-off-by: Swati Agarwal <swati.agarwal@amd.com>
Link: https://lore.kernel.org/r/20220915090516.5812-1-swati.agarwal@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver does not handle the failure case while calling
dma_set_mask_and_coherent API.
In case of failure, capture the return value of API and then report an
error.
Addresses-coverity: Unchecked return value (CHECKED_RETURN)
Signed-off-by: Swati Agarwal <swati.agarwal@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/20220817061125.4720-4-swati.agarwal@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add missing cleanup in devm_platform_ioremap_resource().
When probe fails remove dma channel resources and disable clocks in
accordance with the order of resources allocated .
Signed-off-by: Swati Agarwal <swati.agarwal@xilinx.com>
Link: https://lore.kernel.org/r/20220817061125.4720-2-swati.agarwal@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The strlcpy should not be used because it doesn't limit the source
length. Preferred is strscpy.
Signed-off-by: XueBing Chen <chenxuebing@jari.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/39aa840f.e31.181ed9461c2.Coremail.chenxuebing@jari.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the function xilinx_dpdma_probe(), when get irq failed,
the function platform_get_irq() logs an error message,
so remove redundant message here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20220519130855.7664-1-tangbin@cmss.chinamobile.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This was removed before due to the complete lack of users, but
3218910fd5 ("dmaengine: Add core function and capability check for
DMA_MEMCPY_SG") and 29cf37fa6d ("dmaengine: Add consumer for the new
DMA_MEMCPY_SG API function.") added it back despite still not having
any users whatsoever.
Fixes: 3218910fd5 ("dmaengine: Add core function and capability check for DMA_MEMCPY_SG")
Fixes: 29cf37fa6d ("dmaengine: Add consumer for the new DMA_MEMCPY_SG API function.")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220606074733.622616-1-hch@lst.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
