The log_status function should show HDMI information, but the test checking for
an HDMI input was inverted. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both adv7604 and adv7842 had the same typo in the code that sets
the vertical backporch for the second interlaced field: it was
assigned to vbackporch instead of il_vbackporch.
In addition, the timings struct wasn't zeroed in the adv7842 driver,
leaving several fields to undefined values causing the timing match
function to fail.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Update the recommended writes to those mentioned in the Rev 1.5 version of the
ADV7611 Register Settings Recommendations document released by Analog Devices.
The document does not mention why the recommended settings have been updated,
but presumably those are more fine tuned settings that can enhance performance
in some cases.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an inv_llc_pol field to platform data to control the clock polarity.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The HPD GPIO is used as an output but its direction is never set. Fix
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the hsync-active, vsync-active and pclk-sample
properties to the DT bindings and control BT.656 mode implicitly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Parse the device tree node to populate platform data. Only the ADV7611
is currently support with DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
And set input routing when initializing the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for optional GPIO-controlled HPD pins in addition to the
ADV7604-specific hotplug notifier.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The *_and_or() functions take an 'and' bitmask to be ANDed with the
register value before ORing it with th 'or' bitmask. As the functions
are used to mask and set bits selectively, this requires the caller to
invert the 'and' bitmask and is thus error prone. Replace those
functions with a *_clr_set() variant that takes a mask of bits to be
cleared instead of a mask of bits to be kept.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This allows replacing duplicate code blocks by loops over the arrays.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This one line function is called in a single location. Inline it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the dummy video format operations by pad format operations that
configure the output format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ADV7604 has sink pads for its HDMI and analog inputs. Report them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Control operations are handled by the control framework and the subdev
control handlers are never called directly. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the Analog Devices ADV7611 HDMI receiver.
The adv7611 is quite similar to the adv7604. It has only one instead of four
HDMI inputs and no analog frontend though. Also some register bits have been
shuffled around, but large parts of their register maps are compatible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When extracting multiple bits from a single register read the register
once and extract the bits on the read value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
16-bit registers are read through two 8-bit read operations. Factorize
that common pattern into 16-bit read accessors to simplify the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We do not want to modify the info string arrays ever, so no need to
waste stack space for them. While we are at it also make them const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Register the device with the v4l2 asynchronous probing framework to
support asynchronous instantiation systems such as DT.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The subdev EDID ioctls receive a pad field that must reference an
existing pad and an EDID field that must point to a buffer. Validate
both fields in the core code instead of duplicating validation in all
drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This timing must be supported by all HDMI equipment, so that's a
reasonable default.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some sources are initially detected as DVI, and change to HDMI later.
This must be detected to set the right RGB quantization range.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the restart_stdi_once trick fails to find a valid
format the flag was never reset.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ADV7604_FMT_CHANGE events was debounced in adv7604_isr() to avoid
that a receiver with a unstable input signal would block the event
handling for other inputs. This solution was prone to errors.
A better protection agains interrupt blocking is to delay the call
of the interrupt service routine in the adv7604 driver if too many
interrupts are received within a given time.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- split edid_write_block()
- do not use edid->edid before the validity check
- Return -EINVAL if edid->pad is invalid
- Save both registers for SPA port A
- Set SPA location to default value if it is not found
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the input is ADV7604_INPUT_VGA_RGB and RGB quantization range is
set to V4L2_DV_RGB_RANGE_AUTO, video with CEA timings will be
received as RGB. For ADV7604_INPUT_VGA_COMP, automatic CSC mode
will be selected.
See table 44 on page 205 in "ADV7604 Hardware Manual, Rev. F, August 2010"
for details.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: Mikhail Khelik <mkhelik@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7604 supports four digital input ports. This patch adds support
for all of them, instead of just port A.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
is_private was set right after creating each control, but the control pointer
might be NULL in case of an error. Set it after all controls were successfully
created, since that guarantees that all control pointers are non-NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The CEA-861 standard allows for the 640x480 format at 25.175 MHz.
Ensure that that's allowed according to the struct v4l2_bt_timings_cap.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It's the only function in v4l2-dv-timings.c with the v4l prefix instead
of v4l2. Make it consistent with the other functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These three drivers all have code to log the dv_timings contents. Replace
that code with the new helper function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't log if there is no signal.
If there is a signal, then also log HDCP and audio status.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The frequency calculation has to take deep-color mode into account.
While we're at it, also log the deep-color mode in log_status.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The bridge driver is only notified when the input status has changed
since the previous interrupt.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the new defines to calculate the full blanking and frame sizes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2-common.c contained a bunch of dv-timings related functions.
Move that to the new v4l2-dv-timings.c which is a more appropriate
place for them.
There aren't many drivers that do HDTV, so it is a good idea to separate
common code related to that into a module of its own.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is no longer needed since the core now handles this through DBG_G_CHIP_INFO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes check for EPERM in dbg_g/s_register of subdevice
drivers as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using the managed function the kfree() calls can be removed from the
probe error path and the remove handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* linus/master: (1428 commits)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
jbd: Fix lock ordering bug in journal_unmap_buffer()
...
The STDI block may measure wrong values, especially for lcvs and lcf. If the
driver can not find any valid timing, the STDI block is restarted to measure
the video timings again. The function will return an error, but the restart of
STDI will generate a new STDI interrupt and the format detection process will
restart.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use predefined video timings (prim_mode/vid_std) when available as recommended
by Analog Devices (http://ez.analog.com/message/48267#48267).
Also remove 720p30 support since the ADV7604 can't handle that.
(http://ez.analog.com/message/61488#61488)
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes the way the primary mode is handled:
- Remove it from platform_data since it doesn't belong there.
- Add a new mode enum for use with s_routing.
- Collapse the two HDMI modes into one HDMI mode: when setting up the
timings manually we do not need to select HDMI_COMP mode. That's only
needed when selecting a preset.
This patch prepares for the next step where we switch to using the presets
where available.
Signed-off-by: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial version of this driver.
The full datasheets are available from the Analog Devices website:
http://ez.analog.com/docs/DOC-1545
Not all features of the receiver are supported by this driver for various
reasons. Most notably:
- No CEC support (the CEC API needs a lot more discussion)
- Only port A of the four HDMI input ports is implemented (our hardware only
uses that port)
- No HDCP repeater support (we don't use that either)
And since there are some 600-odd pages of datasheet for this single device,
I'm sure that there are many more things missing, but this driver does work
well for our hardware.
Note that I am using the register addresses instead of register names: the
datasheet containing the register descriptions is organized by register
address. Using names would make the datasheet lookup very hard. An attempt
was made to try and document what is being done when registers are used
instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
