In commit 2c20b9f (ARM: mx25: dynamically allocate mxc-ehci devices) I
changed the offset to the value specified in the reference manual
intending to test this change on hardware. This slipped through and now
prooved to be wrong. So fix it and add a comment about the
documentation being wrong.
Reported-by: Jaume Ribot <jaume@fqingenieria.es>
Cc: Michael Trimarchi <trimarchi@gandalf.sssup.it>
Cc: Shawn Guo <shawn.gsc@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commits 2eb42d5c28 and
9e1dde3387 renamed some defines
but didn't fix all the places where these defines are used
leading to a compile failure for USB on i.MX31, 35 and 27.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The SDMA firmware consists of a ROM part and a RAM part.
The ROM part is always present in the SDMA engine and
is sufficient for many cases.
This patch allows to pass in platform data containing
the script addresses in ROM, so loading a firmware is
optional now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Instead of reading the silicon version from ROM, we should
read the SREV register from the IIM.
Freescale has dropped all support for MX51 REV1.0, only MX51
REV 2.0 and 3.0 are valid.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds a Kconfig option for the avic irq controller
and lets the SoCs that need it select this option.
Also, as we have two irq controllers for i.MX, irq.c is not
appropriate anymore, so rename it to avic.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit "ARM: i.MX IOMUX-V3 replace struct pad_desc with bitmapped cookie"
(b705cb4d42e95a4a43a8945571c8613e71526c3d) introduced a typo which was
preventing my efikamx to boot. This patch is fixing that.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The efikamx board is using a gpio to reset the board so add support
for it
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- add definition to configure pads as ESDHC{1,2} WP and CD
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- ALT0 is used to set GPIO mode of GPIO_1_{2,3,4,5,6,7,8,9} but it's ALT1
for GPIO_1_{0,1}.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The following patch is a first step to convert the 'struct pad_desc'
to a bitmapped cookie to facilitate adding platform specific pullup or
drive strength definitions to existing pad definitions without need to
rewrite the complete pad def.
The patch wraps 'struct pad_desc' in an opaque data type and
introduces macros to access the individual members.
This patch does not constitute any functional change!
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While adapting the #defines for this I noticed that the offset
used for USB HS on i.MX35 differs from the documented offset.
I kept the working offset and commented that the documentation
differs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Compared to the static devices the dynamic have a DMA resource.
This should be save as it seems unused in the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Some usages of ARCH_MX25 are assuming that if it is
defined the other SoCs are undefined. Use SOC_IMX25 for the save
places.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This way FB_IMX can just depend on HAVE_FB_IMX and machines
just need to select IMX_HAVE_PLATFORM_IMX_FB without bothering
about HAVE_FB_IMX.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The mxc-keypad device seems to be the result of an early and partial
merge of the keypad driver. It's unused and there is no corresponding
driver available, so just remove it.
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
To use common macros to define the gpio ports for imx{1,21,25,27} the
existing ones had to made more general and a few more base address defines
were necessary.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
According to the reference manual of the i.MX25 the host controller uses an
offset of 0x200 not 0x400 as was specified in the resources for mxc_usbh2.
Needs-Testing: yes
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Group soc specific data in a global struct instead of repeating it for each
call to imxXX_add_flexcanX. The structs holding the actual data are placed
in .init.constdata and so don't do much harm. Compared to the previous
approach this reduces code size to call imx_add_flexcan.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Currently there is no platform data used in the driver. In case this
changes and for consistency NULL is passed unused to the soc specific
functions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
