If kthread_run failed, we would fail to scan the host, and leak the
allocated async_scan_data. Since using a separate thread is just an
optimisation, do the scan synchronously if we fail to spawn a thread.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The current code prints:
scsi 13:0:4:0: scsi: Device offlined - not ready after error recovery
which is repetitively redundant. This patch changes that message to:
scsi 6:0:6:0: Device offlined - not ready after error recovery
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sg uses a scheme to reallocate a single contiguous array of all its
pointers for lookup and management. This didn't matter too much when sg
could only attach 256 nodes, but now the maximum has been bumped up to
32k we're starting to push the limits of the maximum allocatable
contiguous memory. The solution to this is to eliminate the static
array and do everything via idr, which this patch does.
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The OnStream SCSI Tape driver uses a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Reviewed-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Willem Riede <wrlk@riede.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Remove IRQF_DISABLED, it is clearly wrong for this driver.
* Remove wasteful spin_lock_irqsave() in interrupt handler.
The lighter-weight spin_lock() is all that's needed.
* Annotate with FIXME where arcmsr_interrupt() is called
without any spinlock being acquired.
* Eliminate pointless cast from void pointer in arcmsr_do_interrupt()
[jejb: conflict resolution]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove _interruptible, since receiving a signal while waiting on a
hardware condition will simply cause the driver to busy-wait.
Using msleep_interruptible() is rarely the right thing to do, when
waiting on a hardware condition to change.
Also, replace msleep with ssleep while doing this, where appropriate.
[jejb: fix up merge conflict]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Do not adjust the iIDMA speed on ports which have a faster
link-speed than the HBA itself.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since MSI-X vectors do not require a clearing "handshake" from
the system perspective, and the registered handler will not be
called more than once for one occurrence of receipt of a vector,
there is no requirement to flush the risc register write clearing
the interrupt condition in the risc. Also, since the msi-x
registered handlers are optimised for a particular vector, it is
preferable to handle the one vector received per invocation of
the handler.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make several needlessly global functions static:
- qla2x00_mark_vp_devices_dead()
- qla24xx_configure_vp()
Remove unused function qla24xx_modify_vport().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Drop usage of legacy to_qla_host() macro.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This change reduces by as much as 16% the memory footprint for
each allocated sbr_t structure requested from the mempool.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code, incorrectly passed the address-of a pointer rather
than the pointer value itself.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Also remove legacy '/proc' name during OS_DEVICE_NAME
registration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Where the DPC logic would get jammed into continuously
reloging-into a port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's no need to reset the RISC prior to pausing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Newer ISPs support a mechanism to read and write flash-memory via
the firmware LOAD/DUMP memory mailbox command routines. When
supported, utilizing these mechanisms significantly reduces
overall access times.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
One of the intents of the block prep function was to allow ULDs to use
it for preprocessing. The original SCSI model was to have a single prep
function and add a pointer indirect filter to build the necessary
commands. This patch reverses that, does away with the init_command
field of the scsi_driver structure and makes ULDs attach directly to the
prep function instead. The value is really that it allows us to begin
to separate the ULDs from the SCSI mid layer (as long as they don't use
any core functions---which is hard at the moment---a ULD doesn't even
need SCSI to bind).
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If you build a multiplatform kernel for iSeries and pSeries, with
ibmvscsic support, the resulting client doesn't work on iSeries.
This fixes that, using the appropriate low-level operations
for the machine detected at runtime.
[jejb: fixed up rejections around the srp transport patch]
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
So its ancient, its crap, but it kept showing up in my scans for stuff
that wanted fixing...
- Redo the proc code to be far cleaner
- Clean various return (0) type constructs
- Use cpu_relax()
The various waits ought to time out but thats another issue and probably
not worth solving.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In scsi module I've found some inconsistency between variable type
used in module_param_named and type passed to module_param_named as an
argument. Especially the inconsistency of `max_scsi_luns' parameter is
a bit serious because the description text says "last scsi LUN (should
be between 1 and 2^32-1)".
Signed-off-by: Masatake YAMATO <jet@gyve.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Convert ide-scsi to the new data accessors and cleanup
the !use_sg code paths.
In old code the driver was trying to translate narrow commands,
if received, to wide commands. This code path still assumed
scsi_cmnd->request_buffer is a linear char pointer.
This means that this driver was broken since 2.6.17.
As suggested by Christoph Hellwig I set
use_10_for_rw = 1; and use_10_for_ms = 1;
for this device and completely killed the translation.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A BUSY status returned on a write request results in a stale residual
being returned when the write ultimately successfully completes.
This can be reproduced as follows:
1) issue immediate mode rewind to scsi tape drive
2) issue write request
The tape drive returns busy. The low level driver detects underrun and
sets the residual into the scsi command. The low level driver responds
with (DID_OK << 16) | scsi_status. scsi_status is 8, hence
status_byte(result) == 4, i.e., BUSY.
scsi_softirq_done() calls scsi_decide_disposition() which returns
ADD_TO_MLQUEUE. scsi_softirq_done() then calls scsi_queue_insert()
which, on the way to resubmitting the request to the driver, calls
scsi_init_cmd_errh().
The attached patch modifies scsi_init_cmd_errh() to clear the resid
field. This prevents a "stale" residual from being returned when the
scsi command finally completes without a BUSY status.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
CC [M] drivers/scsi/arcmsr/arcmsr_hba.o
drivers/scsi/arcmsr/arcmsr_attr.c:186: warning: initialization from
incompatible pointer type
drivers/scsi/arcmsr/arcmsr_attr.c:196: warning: initialization from
incompatible pointer type
drivers/scsi/arcmsr/arcmsr_attr.c:206: warning: initialization from
incompatible pointer type
drivers/scsi/arcmsr/arcmsr_hba.c: In function 'arcmsr_alloc_ccb_pool':
drivers/scsi/arcmsr/arcmsr_hba.c:329: warning: assignment from
incompatible pointer type
drivers/scsi/arcmsr/arcmsr_hba.c: At top level:
drivers/scsi/arcmsr/arcmsr_hba.c:101: warning:
'arcmsr_pci_error_detected' declared 'static' but never defined
drivers/scsi/arcmsr/arcmsr_hba.c:102: warning: 'arcmsr_pci_slot_reset'
declared 'static' but never defined
The majority being incorrect casting or the fact that binary attributes
now take an additional argument.
Cc: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Description:
** support ARC1200/1201/1202 SATA RAID adapter, which is named
ACB_ADAPTER_TYPE_B
** modify the arcmsr_pci_slot_reset function
** modify the arcmsr_pci_ers_disconnect_forepart function
** modify the arcmsr_pci_ers_need_reset_forepart function
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This removes the unused sysfs attribute overwriting logic for most of
the attributes, and plugs them into the driver core default attribute
creation.
Without this patch, at the time of the events for the SCSI LUN's, there
will be no sysfs files, because their creation is delayed until the sd
driver has spun up the disks, which might take several seconds. It is the
last WAIT_FOR_SYSFS rule in the default udev setup which can be removed
with this change.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Follow the example of some other drivers by defining DRV_NAME to be
"advansys". Prevents spelling mistakes.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Delete comments relating to the previous structure of the driver.
I have no intention of honouring them ;-)
- Reformat comments > 80 columns
- Remove now-obsolete comments from advansys_interrupt
- Change adv_get_sglist() from do {} while (1) to for (;;)
- Return void from AscInitQLinkVar()
- Take out a level of indentation in adv_get_sglist()
- Reduce indentation level of AscAsyncFix()
- Remove unused macros
- Refactor AscSendScsiQueue slightly
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Replace ASC_ASSERT() with BUG_ON().
In a few places, get rid of the assertion altogether -- the ensuing
crash will tell us all we need to know. Use BUG() where it fits better
than BUG_ON(). Also fix a fencepost error in advansys_proc_info().
- Replace DvcSleepMilliSecond with mdelay.
Despite its name using 'sleep', the implementation was a delay.
I've marked some places with XXX where we should probably be using
msleep instead. They need to be audited to be sure we can sleep in
that context.
- Replace DvcDelayMicroSecond with udelay.
- Replace DvcDelayNanoSecond with udelay too.
All callers were multiples of 1000.
- Remove DvcEnterCritical and DvcLeaveCritical.
These functions are no-ops, and as the comments said, the spinlock
protects the critical sections.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
AscExeScsiQueue() has one caller, and it passes the address of a
variable; this cannot ever be NULL. This is the only place that ever
sets ASCQ_ERR_SCSIQ_NULL_PTR, so delete that error code too, as well as
several other unused ASCQ_ERR codes.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SCSI midlayer won't send commands greater than ->max_cmd_len.
So the checks on length in asc_build_req and adv_build_req are obsolete
and can be deleted, but also we have to set the max_cmd_len in
advansys_board_found(). Also move the length definitions together, and
write a helpful comment.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move as much as possible outside the critical section in queuecommand, eg:
- Set the scsi_done field before acquiring the lock
- Call asc_scsi_done after dropping the lock
Also remove a comment suggesting we should enable interrupts (now we do)
and do some minor reformatting for readability.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The `active' list was used in the reset handler -- but the midlayer
guarantees that list is empty by the time the reset handler is invoked.
It was also checked in the interrupt routines to be sure that this command
belonged to this board, but we don't need to check that either. We can
then delete the asc_prt_target_stats() function as it will never print
anything, along with asc_enqueue(), asc_dequeue_list(), asc_rmqueue(),
asc_scsi_done_list(), struct asc_queue, ASC_QUEUE_EMPTY, ASC_TID_ALL,
ASC_FRONT, ASC_BACK, and all the REQ* macros. Also remove this item from
the todo list.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Move the guts of asc_scsi_done_list() into a new function, asc_scsi_done.
- Call asc_scsi_done() in asc_isr_callback() and adv_isr_callback(). The
comment was wrong; scsi_done cannot enable interrupts.
- All other places which queued an scp on the done list are error paths
for queuecommand, and so we can just call asc_scsi_done() in queuecommand
if we receive an error.
- We no longer need to keep a list of done requests in advansys_interrupt
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The midlayer guarantees it won't call ->queuecommand for a host which
is handling a reset condition.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the adapter is busy, return the request to the midlayer rather than
queueing it in the driver. asc_execute_queue() and asc_dequeue() become
unused, and we don't need to print out stats on the waiting queue any more.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move the error reporting into AscInitGetConfig, AdvInitGetConfig and
AscInitSetConfig.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's just data, so format it to something that looks more visually
appealing (and saves some lines)
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Split AdvLoadMicrocode out of AdvInitAsc3550Driver, AdvInitAsc38C0800Driver
and AdvInitAsc38C1600Driver.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Split AdvBuildCarrierFreelist out of AdvInitAsc3550Driver,
AdvInitAsc38C0800Driver and AdvInitAsc38C1600Driver.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
You can't have two drivers for the same bus type with the same name.
Since ISA and VLB are both isa_drivers, rename the VLB one to advansys_vlb.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
srp transport works for target drivers without supported_mode
attribute but it would be better to use it explicitly.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds minimum target driver support like the srp transport does:
- fc_remote_port_{rolechg,delete} calls
scsi_tgt_it_nexus_{create,destroy} for target drivers.
- add callbacks to notify target drivers of the nexus and tmf
operation results to fc_function_template.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds supported_mode and active_mode attributes to
/sys/class/sys_host/hostX/ for specifying the mode that a lld supports
and the currently activated mode. The output format is similar to fc
rport roles:
luce:/sys/class/scsi_host/host0$ cat supported_mode
Initiator
luce:/sys/class/scsi_host/host0$ cat active_mode
Initiator
The mode values uses bitmap since we would support dual-mode llds in
the future like this:
luce:/sys/class/scsi_host/host0$ cat supported_mode
Initiator, Target
The supported_mode attribute looks at a scsi_host_template and the
active_mode attribute looks at a scsi_host. We would add a hook to a
scsi_host_template to change the active_mode attribute
dynamically. But now there is no hook since no lld supports that
feature.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
should use host->can_queue instead of host->hostt->can_queue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add new HBA PCI ID (0x416) for ASC58300 which has eight port SAS and
SATA PCI-X 133MHz low profile host bus adapter with two mini SAS 4x
external connectors.
Signed-off-by: Gilbert Wu <gilbert_wu@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
updated patch based on Jeff Garzik's comments.
- check adapter firmware version and use appropriate interface accordingly
- add new PCI device IDs and use PCI_VDEVICE macro
- update driver version string
- remove unused data structures
- remove unnecessary typecasts
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This change has already been discussed on linux-scsi:
http://marc.info/?t=118771096400003http://marc.info/?t=118760913100005
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In file included from drivers/scsi/g_NCR5380_mmio.c:9:
drivers/scsi/g_NCR5380.c:559:5: warning: "NCR53C400_PSEUDO_DMA" is not defined
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Every file should #include the headers containing the prototypes for its
global functions (in this case for scsi_schedule_eh()).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/ips.c: In function 'ips_insert_device':
drivers/scsi/ips.c:6957: warning: 'index' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Too generic, clashes with ISDN.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Coverity checker noticed that we may overrun a statically allocated
array in drivers/scsi/lpfc/lpfc_sli.c::lpfc_sli_hbqbuf_find().
The case is this; In 'struct lpfc_hba' we have
#define LPFC_MAX_HBQS 4
...
struct lpfc_hba {
...
struct hbq_s hbqs[LPFC_MAX_HBQS];
...
};
But then in lpfc_sli_hbqbuf_find() we have this code
hbqno = tag >> 16;
if (hbqno > LPFC_MAX_HBQS)
return NULL;
if 'hbqno' ends up as exactely 4, then we won't return, and then this
list_for_each_entry(d_buf, &phba->hbqs[hbqno].hbq_buffer_list, list) {
will cause an overflow of the statically allocated array at index 4,
since the valid indices are only 0-3.
I propose this patch, that simply changes the 'hbqno > LPFC_MAX_HBQS'
into 'hbqno >= LPFC_MAX_HBQS' as a possible fix.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The 700+-line comment at the top of the advansys driver fits more comfortably
in Documentation/scsi.
Delete the sections on:
- kernels supported
- other files modified (obsolete)
- source comments (obsolete)
- tests to run
- release history (that's what a VCS is for)
- contacting connectcom (the domain has expired and the phone number is
now in use by another organisation)
Known problems/fix list is moved down to the section where jejb put his FIXME.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use memcpy to initialise eep_config instead of a loop. For
AdvInitFrom38C1600EEP where we need to modify the default EEPROM
configuration, do it after the loop, and do it using the structure
definition, not by finding the right byte. I think it was wrong for
big-endian machines.
Also delete some non-useful comments and prototypes.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver kept a copy of the PCI config address; refer to the pci_dev
associated with the card instead.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert adv_isr_callback, adv_async_callback and asc_isr_callback into
direct calls. Remove the unused asc_exe_callback.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The cfg structures are supposed to be disposable after initialisation;
with the 'dev' used for DMA mapping in there, that's not possible. Move
the dev to the board.
Also inline AscInitFromAscDvcVar into its only caller, remove some
unnecessary prototypes and sort out a few minor formatting issues.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
n_io_port isn't suitable for advansys because some of the boards have
more than 255 bytes of io port space. There's already a driver-private
replacement, asc_n_io_port, but for some reason the driver was still
setting and occasionally reporting n_io_port.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
At some point during Linux 2.1 development, ioremap() gained the ability
to handle addresses which weren't page-aligned. Also expand the CONFIG_PCI
range to encompass that entire section of wide board initialisation, since
all wide boards are PCI.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
By moving a test from AscGetChipBusType into its only caller, we can delete
the whole function
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove some useless forward declarations
Reformat some comments, debug messages, and the occasional piece of real code
Removal of unnecessary braces
Remove duplicate setting of shost->irq
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use slave_configure() to do all the work that used to be done in
AscInquiryHandling and AdvInquiryHandling. Split slave_configure into
two functions, one for wide and one for narrow controllers.
Remove some unused definitions, duplicate definitions, unnecessary
declarations, and scsireqq, cap_info and inquiry from struct asc_board.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
According to the AdvanSys driver, this device has a problem with tagged
queueing.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
AscCompareString() is just another name for strncmp
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Remove wrappers around the PCI configuration space accessors
- Call pci_set_master() instead of poking at config space directly
- Move the latency setting into one function called for both narrow and
wide boards.
- Tidy up AdvInitGetConfig() a little.
- Delete a few unused prototypes and definitions.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make sure the resources are reserved and released by all the callers of
advansys_board_found(). This eliminates the check_region-style race.
It also allows us to use the pci_request_regions() API.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Register two isa_drivers, one for ISA and one for VLB, in order to
preserve detection order. When deleting advansys_detect, we lose the
last vestiges of the code that limited IO port scanning. This code
has been effectively disabled for many years anyway; I'll restore it
in a module_param later. We also lose the code that placed all ISA PnP
cards into WaitForKey state -- drivers shouldn't be doing this anyway.
The asc_host array goes away too. Also remove some IOADR and other
definitions, such as ASC_NUM_BOARD_SUPPORTED.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Switch EISA probing to the driver model
- Remove some now-unused macros and functions
- Update the FIXME now that we use the correct driver model probing API
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Add a pci_driver interface for the PCI advansys devices (for
ISA/EISA/VLB devices, we still call advansys_detect).
- Many functions are converted from __init to __devinit to allow hotplug
PCI to work.
- Only keep devices found by advansys_detect in the asc_host list.
- Rename asc_board_count to asc_legacy_count. New asc_board_count is only
used to generate a unique name for each device.
- Remove some now-unused macros and struct definitions
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Switch from scsi_register/scsi_unregister to scsi_host_alloc,
scsi_add_host, scsi_scan_host and scsi_host_put.
- Rename the scsi_host_template to advansys_template
- Use module_init and module_exit instead of scsi_module.c
- Remove protection against advansys_detect being called twice
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Put all the error cleanup at the end of the function and goto the
appropriate label
- Split advansys_wide_init_chip out of advansys_board_found
- Split advansys_wide_free_mem out of advansys_board_found. Use it
from advansys_release
- Use GFP_KERNEL, not GFP_ATOMIC, when allocating memory during
initialisation
- Eliminate lots of PROC_FS ifdefs by removing the ifdefs around the prtbuf
struct member
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The interrupt routines used to walk the list of Scsi_Hosts belonging to
this driver to make sure that the scsi_cmnd belonged to one of them.
This is a waste of time and gets in the way of later cleanups, so
delete it.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Pass the Scsi_Host to the interrupt handler, rather than polling all
hosts for each interrupt.
Return IRQ_NONE if we didn't handle this interrupt
Don't set the IRQF_DISABLED flag; this is not a fast-executing interrupt
handler.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Just use the Scsi_Host passed in, rather than looking through the driver's
own array of boards for one that matches it.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update the version to 3.4
Add my copyright
Add myself to MAINTAINERS
Exercise my right to change the license from dual BSD/GPL to GPL
Don't force the definition of CONFIG_ISA on x86
Always include pci.h
Stop including stat.h
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
unsigned short is too small for sizeof(struct scatterlist) *
min(q->max_hw_segments, q->max_phys_segments).
This fixes memory leak with 4096 segments since 16 (likely sg size
with x86) * 4096 sets sglist_len to zero.
This might not happen without sg chaining support.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Stress-testing and some thought has revealed some places where
asynchronous scanning needs some more attention to locking.
- Since async_scan is a bit, we need to hold the host_lock while
modifying it to prevent races against other CPUs modifying the word
that bit is in. This is probably a theoretical race for the moment,
but other patches may change that.
- The async_scan bit means not only that this host is being scanned
asynchronously, but that all the devices attached to this host are not
yet added to sysfs. So we must ensure that this bit is always in sync.
I've chosen to do this with the scan_mutex since it's already acquired
in most of the right places.
- If the host changes state to deleted while we're in the middle of
a scan, we'll end up with some devices on the host's list which must
be deleted. Add a check to scsi_sysfs_add_devices() to ensure the
host is still running.
- To avoid the async_scan bit being protected by three locks, the
async_scan_lock now only protects the scanning_list.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sg's may have setup a the buffer with a different length than
the transfer length so we should be using the bufflen passed
in as the request's data len.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This converts ps3rom driver to use the new accessors for the sg lists
and the parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
it's better to remove tgt dependencies in srp transport class since
most people want only initiator support.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This converts ibmvstgt to use transport tsk_mgmt_response callback.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This moves tsk_mgmt_response callback in struct scsi_host_template to
struct scsi_transport_template since struct scsi_transport_template is
more suitable for the task management stuff.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This converts libsrp and ibmvstgt to use srp transport.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds minimum target driver support:
- srp_rport_{add,del} calls scsi_tgt_it_nexus_{create,destroy} for
target drivers.
- add a callback to notify target drivers of the nexus operation
results to srp_function_template.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
tgt uses scsi_host as I_T nexus. This works for ibmvstgt because it
creates one scsi_host for one initiator. However, other target drivers
don't work like that.
This adds I_T nexus support, which enable one scsi_host to handle
multiple initiators. New scsi_tgt_it_nexus_create/destroy functions
are expected be called transport classes. For example, ibmvstgt
creates an initiator remote port, then the srp transport calls
tgt_it_nexus_create. tgt doesn't manages I_T nexus, instead it tells
tgtd, user-space daemon, to create a new I_T nexus.
On the receiving the response from tgtd, tgt calls
shost->transportt->it_nexus_response. transports should notify a
lld. The srp transport uses it_nexus_response callback in
srp_function_template to do that.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds a 'roles' attribute to rport like transport_fc. The role can
be initiator or target. That is, the initiator driver creates target
remote ports and the target driver creates initiator remote ports.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This converts ibmvscsi to use the srp transport class.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds srp transport class that works with ib_srp and ibmvscsi.
It creates only /sys/class/{srp_host,srp_remote_ports} and
srp_remote_ports has only "port_id" attribute.
viola:/sys/class/srp_remote_ports/port-0:1# ls
device port_id subsystem uevent
viola:/sys/class/srp_remote_ports/port-0:1# cat port_id
4c:49:4e:55:58:20:56:49:4f:00:00:00:00:00:00:00
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (867 commits)
[SKY2]: status polling loop (post merge)
[NET]: Fix NAPI completion handling in some drivers.
[TCP]: Limit processing lost_retrans loop to work-to-do cases
[TCP]: Fix lost_retrans loop vs fastpath problems
[TCP]: No need to re-count fackets_out/sacked_out at RTO
[TCP]: Extract tcp_match_queue_to_sack from sacktag code
[TCP]: Kill almost unused variable pcount from sacktag
[TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
[TCP]: Add bytes_acked (ABC) clearing to FRTO too
[IPv6]: Update setsockopt(IPV6_MULTICAST_IF) to support RFC 3493, try2
[NETFILTER]: x_tables: add missing ip6t_modulename aliases
[NETFILTER]: nf_conntrack_tcp: fix connection reopening
[QETH]: fix qeth_main.c
[NETLINK]: fib_frontend build fixes
[IPv6]: Export userland ND options through netlink (RDNSS support)
[9P]: build fix with !CONFIG_SYSCTL
[NET]: Fix dev_put() and dev_hold() comments
[NET]: make netlink user -> kernel interface synchronious
[NET]: unify netlink kernel socket recognition
[NET]: cleanup 3rd argument in netlink_sendskb
...
Fix up conflicts manually in Documentation/feature-removal-schedule.txt
and my new least favourite crap, the "mod_devicetable" support in the
files include/linux/mod_devicetable.h and scripts/mod/file2alias.c.
(The latter files seem to be explicitly _designed_ to get conflicts when
different subsystems work with them - that have an absolutely horrid
lack of subsystem separation!)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch make processing netlink user -> kernel messages synchronious.
This change was inspired by the talk with Alexey Kuznetsov about current
netlink messages processing. He says that he was badly wrong when introduced
asynchronious user -> kernel communication.
The call netlink_unicast is the only path to send message to the kernel
netlink socket. But, unfortunately, it is also used to send data to the
user.
Before this change the user message has been attached to the socket queue
and sk->sk_data_ready was called. The process has been blocked until all
pending messages were processed. The bad thing is that this processing
may occur in the arbitrary process context.
This patch changes nlk->data_ready callback to get 1 skb and force packet
processing right in the netlink_unicast.
Kernel -> user path in netlink_unicast remains untouched.
EINTR processing for in netlink_run_queue was changed. It forces rtnl_lock
drop, but the process remains in the cycle until the message will be fully
processed. So, there is no need to use this kludges now.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each netlink socket will live in exactly one network namespace,
this includes the controlling kernel sockets.
This patch updates all of the existing netlink protocols
to only support the initial network namespace. Request
by clients in other namespaces will get -ECONREFUSED.
As they would if the kernel did not have the support for
that netlink protocol compiled in.
As each netlink protocol is updated to be multiple network
namespace safe it can register multiple kernel sockets
to acquire a presence in the rest of the network namespaces.
The implementation in af_netlink is a simple filter implementation
at hash table insertion and hash table look up time.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As bi_end_io is only called once when the reqeust is complete,
the 'size' argument is now redundant. Remove it.
Now there is no need for bio_endio to subtract the size completed
from bi_size. So don't do that either.
While we are at it, change bi_end_io to return void.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ll_back_merge_fn is currently exported to SCSI where is it used,
together with blk_rq_bio_prep, in exactly the same way these
functions are used in __blk_rq_map_user.
So move the common code into a new function (blk_rq_append_bio), and
don't export ll_back_merge_fn any longer.
Signed-off-by: Neil Brown <neilb@suse.de>
diff .prev/block/ll_rw_blk.c ./block/ll_rw_blk.c
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The bulk transfer mode got eleminated by
3f6270ef76. Unfortunately, this mode is
required for READ_CAPACITY commands on certain cards, so put it back
again. This fixes a boot failure regression reported by Burton
Windle.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
DMA-mapped SMP (scsi management protocol) requests going /to/ the device
need the PCI DMA data direction to indicate such.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Because the ->unique_id is set too late, the ESP scsi host
instance numbers in the kernel log during probing are
wrong.
Bug reported by Meelis Roos.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Domain Validation in the SPI transport class is failing on boxes with
damaged cables (and failing to the extent that the box hangs). The
problem is that the first test it does is a cable integrity test for
wide transfers and if this fails, it turns the wide bit off. The
problem is that the next set of tests it does turns wide back on
again, with the result that it runs through the entirety of DV with a
known bad setting and then hangs the system.
The attached patch fixes the problem by physically nailing the wide
setting to what it deduces it should be for the whole of Domain
Validation.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] libiscsi: sync up iscsi and scsi eh's access to the connection
[SCSI] libiscsi: fix null ptr regression when aborting a command with data to transfer
[SCSI] qla2xxx: Update version number to 8.02.00-k3.
[SCSI] qla2xxx: Correct mailbox register dump for FWI2 capable ISPs.
[SCSI] qla2xxx: Correct 8GB iIDMA support.
[SCSI] qla2xxx: Correct management-server login-state synchronization issue.
[SCSI] qla2xxx: Don't modify parity bits during ISP25XX restart.
[SCSI] qla2xxx: Allocate enough space for the full PCI descriptor.
[SCSI] zfcp: fix the data buffer accessor patch
[SCSI] zfcp: allocate gid_pn_data objects from gid_pn_cache
[SCSI] zfcp: fix memory leak
Introduce CONFIG_CHECK_SIGNATURE to control inclusion of check_signature()
and avoid problems on platforms that don't have readb().
Let the few legacy (ISA || PCI || X86) drivers that need check_signature()
select CONFIG_CHECK_SIGNATURE.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68k: Fix a few hickups in drivers/scsi/Kconfig
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The iscsi eh could be tearing down the session/connection while
the scsi eh is still sending task management functions. If when
we drop the session lock to grab the recv lock, the iscsi eh
tears down the connection we will oops.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We do not want to send data if we are aborting a task. There is
a check in iscsi_xmit_ctask, but right before calling this we overwrite
the state so we always go right past the test. Sending data causes problems
because when we clean up from a successful abort the LLD assumes that
the task is not running.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original implementation manipulated the FC_GS values for
port-speed. Transition the codes to use the driver's own
internal representations as this makes for a reduction in
duplicate 'conversion' codes throughout the driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Transitioning link-state via NOS/OLS requires a relogin to a
fabric's Management Server. Request relogin when the firmware
issues a point-to-point asynchronous event (0x8030).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the driver fails to allocate the contiguous (DMAable) memory for
system reasons, we fail to load the instance, but then we try to free
the <nul> allocation in the cleanup code and we get a panic in
pci_free_consistent(). This is reported against an older kernel, hope
this is relevant for latest/greatest.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
And finally this is the regular !use_sg cleanup
and use of data accessors.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
check_condition code-path was similar but more
complicated to Reset. It went like this:
1. extra space was allocated at aha152x_scdata for mirroring
scsi_cmnd members.
2. At aha152x_internal_queue() every not check_condition
(REQUEST_SENSE) command was copied to above members in
case of error.
3. At busfree_run() in the DONE_CS phase if a Status of
SAM_STAT_CHECK_CONDITION was detected. The command was
re-queued Internally using aha152x_internal_queue(,,check_condition,)
The old command members are over written with the
REQUEST_SENSE info.
4. At busfree_run() in the DONE_CS phase again. If it is a
check_condition command, info was restored from mirror
made at first call to aha152x_internal_queue() (see 2)
and the command is completed.
What I did is:
1. Allocate less space in aha152x_scdata only for the 16-byte
original command. (which is actually not needed by scsi-ml
anymore at this stage. But this is to much knowledge of scsi-ml)
2. If Status == SAM_STAT_CHECK_CONDITION, then like before
re-queue a REQUEST_SENSE command. But only now save original
command members. (Less of them)
3. In aha152x_internal_queue(), just like for Reset, use the
check_condition hint to set differently the working members.
execute the command.
4. At busfree_run() in the DONE_CS phase again. restore needed
members.
While at it. This patch fixes a BUG. Old code when sending
a REQUEST_SENSE for a failed command. Would than return with
cmd->resid == 0 which was the status of the REQUEST_SENSE.
The failing command resid was lost. And when would resid
be interesting if not on a failing command?
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
What Reset code was doing: Save command's important/dangerous
Info on stack. NULL those members from scsi_cmnd.
Issue a Reset. wait for it to finish than restore members
and return.
What I do is save or NULL nothing. But use the "resetting"
hint in aha152x_internal_queue() to NULL out working members
and leave struct scsi_cmnd alone.
The indent here looks funny but it will change/drop in last
patch and it is clear this way what changed.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
hunk by hunk:
- CHECK_CONDITION is what happens to cmnd->status >> 1
or after status_byte() macro. But here it is used
directly on status which means 0x1 which is an undefined
bit in the standard. And is a status that will never
return from a target.
- in busfree_run at the DONE_SC phase we have 3 distinct
operation:
1-if(DONE_SC->SCp.phase & check_condition)
The REQUEST_SENSE command return.
- Restore original command
- Than continue to operation 3.
2-if(DONE_SC->SCp.Status==SAM_STAT_CHECK_CONDITION)
A regular command returned with a status.
- Internally re-Q a REQUEST_SENSE.
- Do not do operation 3.
3-
- Complete the command and return it to scsi-ml
So the 0x2 in both these operations (1,2) means the scsi
check-condition status, hence SAM_STAT_CHECK_CONDITION
- Here the code asks about !(DONE_SC->SCp.Status & not_issued)
but "not_issued" is an enum belonging to the "phase" member
and not to the Status returned from target. The reason this
works is because not_issued==1 and Also CHECK_CONDITION==1
(remember from hunk 1). So actually the code was asking
!(DONE_SC->SCp.Status & CHECK_CONDITION). Which means
"Has the status been read from target yet?"
Staus is read at status_run(). "not_issued" is
cleared in seldo_run() which is usually earlier than
status_run().
So this patch does nothing as far as assembly is concerned
but it does let the reader understand what is going on.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cause highmem buffers to be bounced to low memory until this
driver supports highmem addresses. Otherwise it just oopses
on NULL buffer addresses.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The symbol <debug_locks> conflicts with the rather global one in
include/linux/locks.h.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Our current implementation has a generic set of barrier functions that
go through the SCSI driver model. Realistically, this is unnecessary,
because the only device that can use barriers (sd) can set the flush
functions up at probe or revalidate time. This patch pulls the barrier
functions out of the mid layer and scsi driver model and relocates them
directly in sd.
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It was pointed out by Boaz Harrosh <bharrosh@panasas.com> that our
8.2.2 lpfc patches revert a change to using SCSI command accessor
functions.
This patch, to be applied on top of the 8.2.2. patches, updates the
driver for the accessor functions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change a printk sequencing issue where <6> ... was coming up in the middle
of a line when scsi_add_host was being called.
Reduce the length of some printk messages and make the messages
more consistant. All cosmetic but it makes it easier to read as it
scrolles off the screen during boot.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Clean up all instances of mixed tab-space indentation
- Clean up sparse build errors
- Add appropriate static's
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Fix vport ndlp ref counting errors
- Fix use after free of ndlp structure
- Use the correct flag to check for LOADING setting.
- Fix driver unload bugs (related to shost references) after link down or rscn
- Fix up HBQ initialization
- Fix port_list locking around driver unload.
- Fix references to hostdata as a phba
- Fix GFFID type offset to work correctly with big endian structure.
- Only call pci_disable_msi if the pci_enable_msi succeeded
- Fix vport_delete wait/fail if in discovery
- Put a reference on the nameservers ndlp when performing CT traffic.
- Remove unbalanced hba unlock.
- Fix up HBQ processing
- Fix lpfc debugfs discovery trace output for ELS rsp cmpl
- Send ADISC when rpi is 0
- Stop FDISC retrying forever
- Unable to retrieve correct config parameter for vport
- Fix sli_validate_fcp_iocb, sli_sum_iocb, sli_abort_iocb to be vport-aware.
- Fix index-out-of-range error in iocb. Spotted by Coverity.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Remove the "management_version" sysfs parameter (was unused)
- Add HBQ information to lpfc debugfs
- Change lpfc_npiv_enable name back to lpfc_enable_npiv (internal stds)
- Remove "issue_lip" attribute from the vports transport template
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rework the lpfc_printf_log() macro so that logging is enabled on a
per-vport basis. Used to be on a physical-port basis, thus logging
with large numbers of vports became a mess. Required redefinition of
the macro, and an update of every use.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Split attributes up into vport and non-vport attributes.
- Move vport specific cfg params to vport
Many of the vport-specific behaviors were still global attributes
on the physical port. Move them to the vport itself.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleans up a lot of bad behaviors that have been in this area a while
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Error messages and debugfs updates:
- Fix up GID_FT error messages
- Enhance debugfs with slow_ring_trace, dumpslim and nodelist information
- Add log type (and messages) for vport state changes
- Enhance log messages when retries ELS fail
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's better to initialize host->shost_data to zero like
target->starget_data and device->sdev_data.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The arm26 port has been in a state where it was far from even compiling
for quite some time.
Ian Molton agreed with the removal.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts d73f5222a6
The bug that made us increase ESP_BUS_TIMEOUT to 275 turned out to be
a memset bug on 32-bit sparc.
It is better to put this back at the correct timeout value than to
leave it increased when there is no reason for doing so.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Delete refereces to HOSTS_C
- Switch to module_init/module_exit instead of detect/release
- Don't pass around the host template and rename it to adpt_template
- Switch from scsi_register/scsi_unregister to scsi_host_alloc,
scsi_add_host, scsi_scan_host and scsi_host_put.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- this patch will fix a panic caused by omitted memory allocation for the nvram.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Not doing this can cause cards less than u160 capable to send out PPR
offers to devices they can't then deliver on ... causing some devices to
get a bit confused. Fix by capping the start syncrate at the
appropriate level according to the card capabilities.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SCSI Tape driver uses a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
