* Rename old pinmux and new pinctrl platform driver and DT match table
entries, so the new driver gets instantiated.
* Re-write board-pinmux.c, so that it uses pinctrl APIs to configura the
pinmux.
* Re-write board-*-pinmux.c so that the pinmux configuration tables are
in pinctrl format.
Ventana's pin mux table needed some edits on top of the basic format
conversion, since some mux options that were previously marked as
reserved are now valid in the new pinctrl driver. Attempting to use the
old reserved names will result in a failure. Specifically, groups lpw0,
lpw2, lsc1, lsck, and lsda were changed from function rsvd4 to displaya,
and group pta was changed from function rsvd2 to hdmi.
All boards' pin mux tables needed some edits on top of the based format
conversion, since function i2c was split into i2c1 (first general I2C
controller) and i2cp (power I2C controller) to better align function
definitions with HW blocks.
Due to the split of mux tables into pure mux and pull/tristate tables,
many entries in the separate Seaboard/Ventana tables could be merged
into the common table, since the entries differed only in the portion
in one of the tables, not both.
Most pin groups allow configuration of mux, tri-state, and pull. However,
some don't allow pull configuration, which is instead configured by new
groups that only allow pull configuration. This is a reflection of the
true HW capabilities, which weren't fully represented by the old pinmux
driver. This required adding new pull table entries for those new groups,
and setting many other entries' pull configuration to
TEGRA_PINCONFIG_DONT_SET.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Recent pinctrl discussions concluded that gpiolib APIs should in fact do
whatever is required to mux a GPIO onto pins, by calling pinctrl APIs if
required. This change implements this for the Tegra GPIO driver, and removes
calls to the Tegra-specific APIs from drivers and board files.
Cc: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Chris Ball <cjb@laptop.org> # for sdhci-tegra.c
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-harmony-pcie.c
To fix an internal merge conflict between the tegra/soc and tegra/boards
branches.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This moves the implementation of *_pinmux_init() into a single location.
The board-specific pinmux data is left in each board's own file. This
will allow future changes that set up the pinmux in a more complex
fashion to do so without duplicating that code in each board's pinmux
file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch modifies the pinmux code to be useable for multiple tegra variants.
Some tegra20 specific constants will be replaced by variables which will be
initialized to the appropriate value at runtime.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This fix updates the CDEV1 pinmux for the paz00 board to be as in the
Harmony board. Paz00 board is originally based on Harmony design.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
*_pinmux_init() register the GPIO and pinmux devices so that they're ready
before any other device needs them.
*_pinmux_init() are also called by board-dt.c in order to set up the GPIO
and pinmux configurations. In this case, if we register the devices, they
end up being probed once due to this registration, and a second time due
to a device-tree node (or vice-versa). The second probe fails since the
memory regions are already requested. Besides, we don't actually want the
duplicated devices.
To avoid this duplicate registration, modify *_pinmux_init() to check
whether it's running on a DT machine. If not, register the pinmux devices.
If so, don't register them.
Finally, modify board-dt.c to call the *_pinmux_init() after all devices have
been instantiated from device-tree. This allows the GPIO and pinmux devices
to be instantiated and initialized before calling functions to configure the
hardware.
This has one disadvantage: The pinmux and GPIO initialization now happens
after /all/ devices are instantiated, rather than after just gpio and
pinmux but before anything else. So the correct HW configuration is not
in place when e.g. the SD/MMC device is probed. Long-term, this should be
solved by doing both:
a) Initializing the HW state from DT nodes during GPIO and pinmux device
probe.
b) Using the deferred driver probe mechanism, so that drivers can defer
their probe until after the gpio and pinmux drivers have probed.
v2: s/int is_dt/bool is_dt/
v3: Use of_machine_is_compatible inside *_pinmux_init() rather than passing
an explicit parameter into the function from outside.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
The Tegra GPIO driver will be converted from static registration via
postcore_initcall() to be a platform device later in this patch series.
A new Tegra pinmux platform device will also be added.
Prepare for this by modifying all boards to register the appropriate
platform devices before-hand, so that when the drivers are converted,
those devices will be probed, and git bisectability will be maintained.
v2: Add resource definitions for GPIO and pinmux
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for the wifi led. It is automaticly triggered by
the rfkill0 event.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for controlling the rfkill gpios for the
internal WIFI card via the rfkill_gpio driver.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
The internal storage has no gpios connected to. Also the second
port is not connected at all, so remove it from the board file.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Colin Cross <ccross@android.com>
This patch add support for the second and third ehci bus on paz00.
The first bus needs gadget and nvec support and will be added once
the needed patches are upstream.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Colin Cross <ccross@android.com>
This patch replaces long sequences of spaces by tabs and tabs by
spaces were appropriate.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Colin Cross <ccross@android.com>
This patch adds the config infrastructure, the pinmux and basic
board setup code for PAZ00 (name of board inside the AC100/AZ).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
