The service parameters for the VPI/RPIs were incorrect, resulting in
lower utilization
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
T10 Diff fixes and enhancements:
- Add SLI4 Lancer support for T10 DIF / BlockGuard (121980)
- Fix SLI4 BlockGuard behavior when protection data is generated by HBA (121980)
- Enhance debugfs for injecting T10 DIF errors (123966, 132966)
- Fix Incorrect usage of bghm for BlockGuard errors (127022)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
SLI related fixes:
- Fix REG_RPI fails on SLI4 HBA putting NPort into NPR state (126230)
- Fix ELS FDISC failing with local reject / invalid RPI. (126350)
- Fix reset port when reset is needed during fw_dump (125807)
- Fix unbounded firmware revision string from port cause panic (126560)
- Fix driver behavior when receiving an ADISC (126654)
- Fix driver not returning when bad ndlp found in abts error event
handling (126209)
- Add more driver logs in area of SLI4 port error attention and reset
recovery (126813, 124466)
- Fix failure in handling large CQ/EQ identifiers in an IOV
environment (126856)
- Fix for driver using duplicate RPIs after lancer port reset (126723)
- Clear vport->fc_myDID in lpfc_els_issue_fdisc to guarentee a
zero SID (126779, 126897)
- Fix for SLI4 Port delivery for BLS ABORT ACC (126289)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Add Basic support for SLI4 Loopback.
(CR 124951, 125766, 124951, 125843, 125832, 125843)
- Added missing protection in setting/clearing of phba->link_flag bit
field (CR 125994)
- Use link type and link number obtained from READ_CONFIG mailbox
command. (CR 126264)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FC and SCSI Discovery Fixes:
- Clear the virtual fabrics bit (word 1 bit 30) when sending the FLOGI
and FDISC. (CR 124339)
- Return a MLQUEUE_DEVICE_BUSY if the driver detects that an I/O is being
retried too quickly (CR 124668)
- Remove NDLP reference put in lpfc_cmpl_els_logo_acc for all but fabric
nodes (CR 123924)
- Only retry FDISCs every second and stop retrying after devloss number
of retries (CR 13939)
- Check to see if vports are unloading before adding them to the vport
work array. (CR 124996)
- Fixed illegal state transition during driver unload (CR 124191)
- Added missing protection on setting/clearing of vport->fc_flag bit (CR 126002)
- Set NPIV flag in lpfc_mbx_process_link_up for all ports sli3 and
above. (CR 126094)
- Clear FCP command bytes that are not used. (CR 126209)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Miscellaneous fixes in sysfs and mgmt interfaces:
- Added SLI4 INTF_TYPE and SLI_FAMILY as sub-field to the fwrev sysfs
attribute (CR 124103)
- Added a sysfs attribute "protocol" to report SLI4 port link protocol
type (CR 124102)
- Increment mix-and-match minor number by 1 for added "protocol" sysfs
attribute. (124102)
- Move the link speed check into the generic sli3/sli4 code
path. (CR 124185, 124122)
- Deleted check for inExtWLen (CR 122523)
- Add the word "offline" to message 2889 (CR 124385)
- Conditionalize the firmware upgrade/downgrade so that it is only
attempted for SLI4 type 2 boards (CR 124406)
- Return an error if the mbox sysfs is called. (CR 124210)
- When port_state is less than LPFC_VPORT_READY, report
FC_PORTSTATE_BYPASSED (CR 120018)
- Added driver support for performing persistent linkdown based on
configure region 23 (CR 124534)
- Added restore state and error log when sysfs board_mode attribute
access failed (CR 124158)
- Added support for SLI4_CONFIG non-embedded COMN_GET_CNTL_ADDL_ATTR
pass-through (CR 124466)
- Rejecting un-supported multi-buffer mailbox commands (CR 124771)
- Byte swap the extended data request and response data for extended
mailbox data (CR 125081)
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implemented new algorithm for getting physical port name for all SLI4 devices
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changed the timeout value for flash-based SLI_CONFIG (0x9B)
mailbox command to 300 seconds for worst case flash delays.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Miscellanous logic and interface fixes
- Fix lpfc_init_vfi_cmpl to check the interface type for interface type 0
before parsing the results.
- Cast uint32_t values that are multiplied to uint64_t before the
multiplication.
- Instead of "break" statement when PCI read returned error, use the goto
statement to the end of the routine after setting return value
- moved the msleep(10) to the beginning of the wait loop for checking the
SLIPort_Status register
- Added the code to follow the existing wait for SLIPort_Status register RDY,
ERR, and RN bits to be set by the port before proceeding to perform PCI
function reset.
- Do not override ulpCt_h and ulpCt_l for SLI 4 ports.
- For vport delete, call lpfc_nlp_put when the vport's vpi state is not
marked with VPI_REGISTERED.
- Added missed fields into the driver's Controller Attributes Structure
- Changed ringing EQ/CQ/RQ doorbell register to be dependent on the size
of the queue.
- Return -EACCES in issue_reset if cfg_enable_hba_reset is zero.
- Added new logging flag LOG_FCP_UNDER 0x00040000 to qualify underrun logging.
- Add a check in the fabric name display routine to display 0 if the port
state is <= FLOGI.
- Add a check to the switch statement in lpfc_decode_firmware_rev to check
for an 'X'.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix HBA initialization issues
- Swap all values that come from the firmware image on little endian systems.
Created a new bf_get_be macro that does the same as the bf_get_le macro but
for big endian data instead of little endian data.
- Moved the incrementing of temp_offset after the copy
fixed the write object loop to use temp_offset to figure out where the end
of the image is instead of offset.
- Added the necessary codes for properly bringing the driver instance offline
and then trying to bring the port back online with the PCI function IP reset.
If it fails to bring the SLI port back online, it will fall through to
bringing the SLI port to HBA error offline.
- Add a call in the probe_one_s3 and probe_one_s4 routines to get the Modeldesc
- Change OCe50100 to OCe15100
- Made the error log also include the PCI BAR bitmap returned from kernel call
pci_select_bars().
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adapter Interface fixes and changes
- Modify the macro field from lpfc_init_vpi_vpi to lpfc_init_vfi_vpi
- Add the new CQE_CODE_RECEIVE_V1 CQE Code, add code in the driver to handle
the new Code the same as the CQE_CODE_RECEIVE code except that there are
two new checks for this code that will cause the driver to use the new V1
macros for rq_id and fcf_id.
- Fix a bug in lpfc_prep_seq() where the size out of the first CQE was
ONLY being used, even though multiple dmabufs make up the sequence,
each have their own CQE with potentially different sizes.
- Fix bug in lpfc_bsg_ct_unsol_event() where the ulpContext and ulpWord[3]
fields of the XMIT_SEQUENCE64_CX IOCB were being calculated incorrectly.
- Do physical to logical translation before indexing into the active
XRI array.
- Populate physical vpi in the iocb data structure.
- Put the current accumulated total in each IOCB in the chain as we are
walking thru then. The last IOCB in the chain should have the total
length of the sequence.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Miscellaneous Bug fixes and code cleanup
- Fix 16G link speed reporting by adding check for 16G check.
- Change the check and enforcement of MAILBOX_EXT_SIZE (2048B)
to the check and enforcement of BSG_MBOX_SIZE - sizeof(MAILBOX_t) (3840B).
- Instead of waiting for a fixed amount of time after performing firmware
reset, the driver shall wait for the Lancer SLIPORT_STATUS register for the
readiness of the firmware for bring up.
- Add logging to indicate when dynamic parameters are changed.
- Add revision and date to the firmware image format.
- Use revision instead of rev_name to check firmware image version.
- Update temporary offset after memcopy is complete for firmware update.
- Consolidated the use of the macros to get rid of duplicated register
offset definitions.
- Removed the unused second parameter in routine lpfc_bsg_diag_mode_enter()
- Enable debugfs when debugfs is enabled.
- Update function comments for lpfc_sli4_alloc_xri and lpfc_sli4_init_rpi_hdrs.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Extend BSG infrastructure and add link diagnostics:
- Removed unnecessary copies in handling pass-through mbox cmds.
- Add embedded SLI_CONFIG support for BSG.
- Add multibuffer support.
- Implemented the setting up and tearing down Lancer FC device for performing
internal and external loopback diagnostic tests.
- Implemented the driver support for performing new link diagnostic tests
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.
[jejb: checkpatch.pl fixes]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Add request-firmware support:
- Add support for request_firmware interface for INTF2 SLI4 ports.
- Add ability to reset SLI4 INTF2 ports.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Extended hardware support and support dump images:
- Make the size to be MAILBOX_SYSFS_MAX (4096) so that it allows the maximum
sysfs binary access interface possible.
- Add ids and model names for new hardware
- Add capability of inducing SLI4 firmware dump obj file
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Miscellaneous Fixes and Corrections
- Remove the memset in the lpfc_sli4_remove_rpi_hdrs call.
- Correct swapping of SGE word 2 relative to offset value
- Reorganize CQ and EQ usage to comply with SLI4 Specification.
- Expand the driver to check the rn bit. Only detect an error if the error bit
is set and the RN bit is NOT set.
- If mailbox completion code is not success AND the mailbox status is success,
then and only then will the driver overwrite the mailbox status.
- When driver initializing device, if the device is on a PCIe bus, set
PCI's "needs fundamental reset" bit so that EEH uses fundamental reset
instead of hot reset for recovery.
- Prevent driver from using new WWN when changed in firmware (until driver
reload)
- When HBA reports maximum SGE size > 0xffffffff (infinite), override
with 0x80000000.
- Fixed potential missed SLI4 device initialization failure conditions.
- Added 100ms delay before driver action following IF_TYPE_2 function reset.
- Reverted patch to UNREG/REG on PLOGI to mapped/unmapped node.
- Add a check for the CVL received flag in the fcf inuse routine to avoid
unregistering the fcf if Devloss fires before Delay discover timer fires.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Fixes related to new hardware
- Restrict driver to look at BAR2 or BAR4 only for if_type 0.
- Allow SLI4 with FCOE_MODE not set for new SLI4 FC adapters.
- Add Temporary RPI field to the ELS request WQE.
- Do not override CT field in issue_els_flogi for SLI4 IF type 2
- For RQ_CREATE_V2 mbx cmd: fill in the rqe_size and page_size for RQ_CREATE.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Miscellaneous fixes
- Do not limit RPI Count to a minimum of 64
- Fix FCFI incorrect on received unsolicited frames.
- Save the FCFI returned in the REG_FCFI mailbox command if it was successful.
- Fixed Vports not sending FDISC after lips.
- Align based on the SLI4_PAGE_SIZE.
- Fixed double byte swap on received RRQ.
- Fixed mask size for the wq_id mask from 0x7F to 0x7FFF.
- Clear FC_FABRIC flag when NPIV LOGO completes (and add a log message).
- Modified driver to skip round robin only when ulpStatus==LOCAL_REJECT
and word4=SEQUENCE_TIMEOUT to prevent FLOGI to disconnected FCF.
- Don't add rport if driver unloading
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FC Discovery fixes
- In lpfc_sli4_bpl2sgl byte swapping the SGL in word2.
- In lpfc_sli4_iocb2wqe byteswap the data for CMD_GEN_REQUEST64_CR type WQE.
- In lpfc_sli4_seq_abort_acc do not set the oxid into the iocb's xritag field.
- In lpfc_sli4_seq_abort_acc check the return value of lpfc_sli_issue_iocb.
- Inprove messages in this area.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add new Queue Create Mailbox version support
- Make lpfc_bsg_wake_mbox_wait routine check the mailboxes job reference before
using it.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Critical Errors:
- Correctly handle non-zero return lpfc_workq_post_event and return ENOMEM
- Save the irq level when locking the host_lock in lpfc_findnode_did
Bug Fixes:
- Adjust payload_length and request_length for sli4_config mailbox commands.
- Add the freed sgl/XRI to the tail of the list rather than to the head.
- Set the FC_VPORT_NEEDS_INIT_VPI on vport deletes and check it before
issuing a fdisc on an els retry.
- Only call lpfc_hba_init_link() if phba->cfg_suppress_link_up
is LPFC_INITIALIZE_LINK.
- Add support for SLI-4 Performance Hints
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Implement new SLI4 init procedures based on if_type:
- Add structure changes for new SLIPORT registers and BAR changes.
- Update register names to be consistent with inteface spec terms.
- Added union to encapsulate Hardward error registers.
- Rework lpfc_sli4_post_status_check() around SLI-4's SLI_INTF type
- Removed the lpfc_sli4_fw_cfg_check routine
- Segmented driver logic to include evaluation of the if_type to
engage different behaviors.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Implement the FC and SLI async event handlers:
- Updated MQ_CREATE_EXT mailbox structure to include fc and SLI async events.
- Added the SLI trailer code.
- Split physical field into type and number to reflect latest SLI spec.
- Changed lpfc_acqe_fcoe to lpfc_acqe_fip to reflect latest Spec changes.
- Added lpfc_acqe_fc_la structure for FC link attention async events.
- Added lpfc_acqe_sli structure for sli async events.
- Added lpfc_sli4_async_fc_evt routine to handle fc la async events.
- Added lpfc_sli4_async_sli routine to handle sli async events.
- Moved LPFC_TRAILER_CODE_FC to be handled by its own handler function.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add SLI4 FC Discovery support
- Replace READ_LA and READ_LA64 with READ_TOPOLOGY mailbox command.
- Converted the old READ_LA structure to use bf_set/get instead of bit fields.
- Rename HBA_FCOE_SUPPORT flag to HBA_FCOE_MODE. Flag now indicates function
is running as SLI-4 FC or FCoE port. Make sure flag reset each time
READ_REV completed as it can dynamically change.
- Removed BDE union in the READ_TOPOLOGY mailbox command and added a define to
define the ALPA MAP SIZE. Added FC Code for async events.
- Added code to support new 16G link speed.
- Define new set of values to keep track of valid user settable link speeds.
- Used new link speed definitions to define link speed max and bitmap.
- Redefined FDMI Port sppeds to be hax values and added the 16G value.
- Added new CQE trailer code for FC Events.
- Add lpfc_issue_init_vfi and lpfc_init_vfi_cmpl routines.
- Replace many calls to the initial_flogi routine with lpfc_issue_init_vfi.
- Add vp and vpi fields to the INIT_VFI mailbox command.
- Addapt lpfc_hba_init_link routine for SLI4 use.
- Use lpfc_hba_init_link call from lpfc_sli4_hba_setup.
- Add a check for FC mode to register the FCFI before init link.
- Convert lpfc_sli4_init_vpi to be called without a vpi (get it from vport).
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add the Lancer FC and FCoE PCI IDs
- Add new SLI4 INTF register definitions
- Implement new SLI4 doorbell register
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
