This patch (as154) fixes a self-deadlock that occurs when userspace
writes to the bConfigurationValue sysfs attribute for a hub with
children. The task tries to lock the bandwidth_mutex at a time when
it already owns the lock:
The attribute's method calls usb_set_configuration(),
which calls usb_disable_device() with the bandwidth_mutex
held.
usb_disable_device() unregisters the existing interfaces,
which causes the hub driver to be unbound.
The hub_disconnect() routine calls hub_quiesce(), which
calls usb_disconnect() for each of the hub's children.
usb_disconnect() attempts to acquire the bandwidth_mutex
around a call to usb_disable_device().
The solution is to make usb_disable_device() acquire the mutex for
itself instead of requiring the caller to hold it. Then the mutex can
cover only the bandwidth deallocation operation and not the region
where the interfaces are unregistered.
This has the potential to change system behavior slightly when a
config change races with another config or altsetting change. Some of
the bandwidth released from the old config might get claimed by the
other config or altsetting, make it impossible to restore the old
config in case of a failure. But since we don't try to recover from
config-change failures anyway, this doesn't matter.
[This should be marked for stable kernels that contain the commit
fccf4e8620 "USB: Free bandwidth when
usb_disable_device is called."
That commit was marked for stable kernels as old as 2.6.32.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the Seagate Goflex USB3.0 device is attached to VIA xHCI
host, sometimes the device will downgrade mode to high speed.
By the USB analyzer, I found the device finished the link
training process and worked at superspeed mode. But the device
descriptor got from the device shows the device works at 2.1.
It is very strange and seems like the device controller of
Seagate Goflex has a little confusion.
The first 8 bytes of device descriptor should be:
12 01 00 03 00 00 00 09
But the first 8 bytes of wrong device descriptor are:
12 01 10 02 00 00 00 40
The wrong device descriptor caused the initialization of mass
storage failed. After a while, the device would be recognized
as a high speed device and works fine.
This patch will warm reset the device to fix the issue after
finding the bcdUSB field of device descriptor isn't 0x0300
but the speed mode of device is superspeed.
This patch should be backported to kernels as old as 3.2, or ones that
contain the commit 75d7cf72ab "usbcore:
refine warm reset logic".
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Acked-by: Andiry Xu <Andiry.Xu@amd.com>
Acked-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch (as1533) fixes a race between root-hub suspend and remote
wakeup. If a wakeup event occurs while a root hub is suspending, it
might not cause the suspend to fail. Although the host controller
drivers check for pending wakeup events at the start of their
bus_suspend routines, they generally do not check for wakeup events
while the routines are running.
In addition, if a wakeup event occurs any time after khubd is frozen
and before the root hub is fully suspended, it might not cause a
system sleep transition to fail. For example, the host controller
drivers do not fail root-hub suspends when a connect-change event is
pending.
To fix both these issues, this patch causes hcd_bus_suspend() to query
the controller driver's hub_status_data method after a root hub is
suspended, if the root hub is enabled for wakeup. Any pending status
changes will count as wakeup events, causing the root hub to be
resumed and the overall suspend to fail with -EBUSY.
A significant point is that not all events are reflected immediately
in the status bits. Both EHCI and UHCI controllers notify the CPU
when remote wakeup begins on a port, but the port's suspend-change
status bit doesn't get set until after the port has completed the
transition out of the suspend state, some 25 milliseconds later.
Consequently, the patch will interpret any nonzero return value from
hub_status_data as indicating a pending event, even if none of the
status bits are set in the data buffer. Follow-up patches make the
necessary changes to ehci-hcd and uhci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Chen Peter-B29397 <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1532) fixes a mistake in the USB suspend code. When the
system is going to sleep, we should ignore errors in powering down USB
devices, because they don't really matter. The devices will go to low
power anyway when the entire USB bus gets suspended (except for
SuperSpeed devices; maybe they will need special treatment later).
However we should not ignore errors in suspending root hubs,
especially if the error indicates that the suspend raced with a wakeup
request. Doing so might leave the bus powered on while the system was
supposed to be asleep, or it might cause the suspend of the root hub's
parent controller device to fail, or it might cause a wakeup request
to be ignored.
The patch fixes the problem by ignoring errors only when the device in
question is not a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chen Peter <B29397@freescale.com>
CC: <stable@vger.kernel.org>
Tested-by: Chen Peter <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to catch the resume bug that was bothering lots of us from
testing some XHCI bug fixes in the suspend/resume path.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1534c) updates the documentation for usb_unlink_urb and
related functions. It explains that the caller must prevent the URB
being unlinked from getting deallocated while the unlink is taking
place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1517b) fixes an error in the USB scatter-gather library.
The library code uses urb->dev to determine whether or nor an URB is
currently active; the completion handler sets urb->dev to NULL.
However the core unlinking routines need to use urb->dev. Since
unlinking always racing with completion, the completion handler must
not clear urb->dev -- it can lead to invalid memory accesses when a
transfer has to be cancelled.
This patch fixes the problem by getting rid of the lines that clear
urb->dev after urb has been submitted. As a result we may end up
trying to unlink an URB that failed in submission or that has already
completed, so an extra check is added after each unlink to avoid
printing an error message when this happens. The checks are updated
in both sg_complete() and sg_cancel(), and the second is updated to
match the first (currently it prints out unnecessary warning messages
if a device is unplugged while a transfer is in progress).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Illia Zaitsev <I.Zaitsev@adbglobal.com>
CC: Ming Lei <tom.leiming@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile 1 from Al Viro:
"This is _not_ all; in particular, Miklos' and Jan's stuff is not there
yet."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (64 commits)
ext4: initialization of ext4_li_mtx needs to be done earlier
debugfs-related mode_t whack-a-mole
hfsplus: add an ioctl to bless files
hfsplus: change finder_info to u32
hfsplus: initialise userflags
qnx4: new helper - try_extent()
qnx4: get rid of qnx4_bread/qnx4_getblk
take removal of PF_FORKNOEXEC to flush_old_exec()
trim includes in inode.c
um: uml_dup_mmap() relies on ->mmap_sem being held, but activate_mm() doesn't hold it
um: embed ->stub_pages[] into mmu_context
gadgetfs: list_for_each_safe() misuse
ocfs2: fix leaks on failure exits in module_init
ecryptfs: make register_filesystem() the last potential failure exit
ntfs: forgets to unregister sysctls on register_filesystem() failure
logfs: missing cleanup on register_filesystem() failure
jfs: mising cleanup on register_filesystem() failure
make configfs_pin_fs() return root dentry on success
configfs: configfs_create_dir() has parent dentry in dentry->d_parent
configfs: sanitize configfs_create()
...
Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and other
various minor things.
There are some patches touching arch code, but they have all been acked
by the various arch maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9njL8ACgkQMUfUDdst+ylQ9wCfbBOnIT01lGOorkaE9pom0hhk
HfMAoKq1xzCR2B+OS3UMyUQffk+Ri9Ri
=KIQ2
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB merge for 3.4-rc1 from Greg KH:
"Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and
other various minor things.
There are some patches touching arch code, but they have all been
acked by the various arch maintainers."
* tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (302 commits)
net: qmi_wwan: add support for ZTE MF820D
USB: option: add ZTE MF820D
usb: gadget: f_fs: Remove lock is held before freeing checks
USB: option: make interface blacklist work again
usb/ub: deprecate & schedule for removal the "Low Performance USB Block" driver
USB: ohci-pxa27x: add clk_prepare/clk_unprepare calls
USB: use generic platform driver on ath79
USB: EHCI: Add a generic platform device driver
USB: OHCI: Add a generic platform device driver
USB: ftdi_sio: new PID: LUMEL PD12
USB: ftdi_sio: add support for FT-X series devices
USB: serial: mos7840: Fixed MCS7820 device attach problem
usb: Don't make USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.
usb gadget: fix a section mismatch when compiling g_ffs with CONFIG_USB_FUNCTIONFS_ETH
USB: ohci-nxp: Remove i2c_write(), use smbus
USB: ohci-nxp: Support for LPC32xx
USB: ohci-nxp: Rename symbols from pnx4008 to nxp
USB: OHCI-HCD: Rename ohci-pnx4008 to ohci-nxp
usb: gadget: Kconfig: fix typo for 'different'
usb: dwc3: pci: fix another failure path in dwc3_pci_probe()
...
Non-hub device has no child, and even a real USB hub has ports far
less than USB_MAXCHILDREN, so there is no need using a fix array for
child devices, just allocate it dynamically according real port
number.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel doc entry for usb_unlink_urb() contains the phrase "This
request is always asynchronous.". The "always" leads to the assumption
that the ->complete() callback is not called from within
usb_unlink_urb(). This is not true. The HCD is allowed to call the
->complete() from within ->urb_dequeue() if it is appropriate for the
hardware.
This patch updates the kernel doc so usb-device driver authors make sure
to drop all locks (and make sure it is okay to drop them) which are
acquired by the complete callback before calling usb_unlink_urb().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's really no point in having hcd->irq as a
signed integer when we consider the fact that
IRQ 0 means NO_IRQ. In order to avoid confusion,
make hcd->irq unsigned and fix users who were
passing -1 as the IRQ number to usb_add_hcd.
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shows up on ia64 builds (and possibly elsewhere) for configs that
don't set PM_RUNTIME or PM_SLEEP as follows:
drivers/usb/core/hcd-pci.c:383:12: warning: 'suspend_common' defined but not used
drivers/usb/core/hcd-pci.c:438:12: warning: 'resume_common' defined but not used
As per above, the functions are only used if RUNTIME/SLEEP are set,
so make the two functions conditional on these Kconfig values.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pull in the xhci changes and the other fixes and device id
updates that were done in Linus's tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The superspeed device attached to a USB 3.0 hub(such as VIA's)
doesn't respond the address device command after resume. The
root cause is the superspeed hub will miss the Hub Depth value
that is used as an offset into the route string to locate the
bits it uses to determine the downstream port number after
reset, and all packets can't be routed to the device attached
to the superspeed hub.
Hub driver sends a Set Hub Depth request to the superspeed hub
except for USB 3.0 root hub when the hub is initialized and
doesn't send the request again after reset due to the resume
process. So moving the code that sends the Set Hub Depth request
to the superspeed hub from hub_configure() to hub_activate()
is to cover those situations include initialization and reset.
The patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Now that USB 3.0 hub remote wakeup on port status changes is enabled,
and USB 3.0 device remote wakeup is handled in the USB core properly,
let's turn on auto-suspend for all USB 3.0 hubs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch takes care of the race condition between the Function Wake
Device Notification and the auto-suspend timeout for this situation:
Roothub
| (U3)
hub A
| (U3)
hub B
| (U3)
device C
When device C signals a resume, the xHCI driver will set the wakeup_bits
for the roothub port that hub A is attached to. However, since USB 3.0
hubs do not set a link state change bit on device-initiated resume, hub
A will not indicate a port event when polled. Without this patch, khubd
will notice the wakeup-bits are set for the roothub port, it will resume
hub A, and then it will poll the events bits for hub A and notice that
nothing has changed. Then it will be suspended after 2 seconds.
Change hub_activate() to look at the port link state for each USB 3.0
hub port, and set hub->change_bits if the link state is U0, indicating
the device has finished resume. Change the resume function called by
hub_events(), hub_handle_remote_wakeup(), to check the link status
for resume instead of just the port's wakeup_bits.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB 3.0 hubs don't have a port suspend change bit (that bit is now
reserved). Instead, when a host-initiated resume finishes, the hub sets
the port link state change bit.
When a USB 3.0 device initiates remote wakeup, the parent hubs with
their upstream links in U3 will pass the LFPS up the chain. The first
hub that has an upstream link in U0 (which may be the roothub) will
reflect that LFPS back down the path to the device.
However, the parent hubs in the resumed path will not set their link
state change bit. Instead, the device that initiated the resume has to
send an asynchronous "Function Wake" Device Notification up to the host
controller. Therefore, we need a way to notify the USB core of a device
resume without going through the normal hub URB completion method.
First, make the xHCI roothub act like an external USB 3.0 hub and not
pass up the port link state change bit when a device-initiated resume
finishes. Introduce a new xHCI bit field, port_remote_wakeup, so that
we can tell the difference between a port coming out of the U3Exit state
(host-initiated resume) and the RExit state (ending state of
device-initiated resume).
Since the USB core can't tell whether a port on a hub has resumed by
looking at the Hub Status buffer, we need to introduce a bitfield,
wakeup_bits, that indicates which ports have resumed. When the xHCI
driver notices a port finishing a device-initiated resume, we call into
a new USB core function, usb_wakeup_notification(), that will set
the right bit in wakeup_bits, and kick khubd for that hub.
We also call usb_wakeup_notification() when the Function Wake Device
Notification is received by the xHCI driver. This covers the case where
the link between the roothub and the first-tier hub is in U0, and the
hub reflects the resume signaling back to the device without giving any
indication it has done so until the device sends the Function Wake
notification.
Change the code in khubd that handles the remote wakeup to look at the
state the USB core thinks the device is in, and handle the remote wakeup
if the port's wakeup bit is set.
This patch only takes care of the case where the device is attached
directly to the roothub, or the USB 3.0 hub that is attached to the root
hub is the device sending the Function Wake Device Notification (e.g.
because a new USB device was attached). The other cases will be covered
in a second patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Refactor the code to check for a remote wakeup on a port into its own
function. Keep the behavior the same, and set connect_change in
hub_events if the device disconnected on resume. Cleanup references to
hdev->children[i-1] to use a common variable.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB 3.0 hubs have a different remote wakeup policy than USB 2.0 hubs.
USB 2.0 hubs, once they have remote wakeup enabled, will always send
remote wakes when anything changes on a port.
However, USB 3.0 hubs have a per-port remote wake up policy that is off
by default. The Set Feature remote wake mask can be changed for any
port, enabling remote wakeup for a connect, disconnect, or overcurrent
event, much like EHCI and xHCI host controller "wake on" port status
bits. The bits are cleared to zero on the initial hub power on, or
after the hub has been reset.
Without this patch, when a USB 3.0 hub gets suspended, it will not send
a remote wakeup on device connect or disconnect. This would show up to
the user as "dead ports" unless they ran lsusb -v (since newer versions
of lsusb use the sysfs files, rather than sending control transfers).
Change the hub driver's suspend method to enable remote wake up for
disconnect, connect, and overcurrent for all ports on the hub. Modify
the xHCI driver's roothub code to handle that request, and set the "wake
on" bits in the port status registers accordingly.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB 3.0 bus specification introduces a new type of power management
called function suspend. The idea is to be able to suspend different
functions (i.e. a scanner or an SD card reader on a USB printer)
independently. A device can be in U0, but have one or more functions
suspended. Thus, signaling a function resume with the standard device
remote wake signaling was not possible.
Instead, a device will (without prompt from the host) send a "device
notification" for the function remote wake. A new Set Feature Function
Remote Wake was developed to turn remote wake up on and off for each
function.
USB 3.0 devices can still go into device suspend (U3), and signal a
remote wakeup to bring the link back into U1. However, they now use the
function remote wake device notification to allow the host to know which
function woke the device from U3.
The spec is a bit ambiguous about whether a function is allowed to
signal a remote wakeup if the function has been enabled for remote
wakeup, but not placed in function suspend before the device is placed
into U3.
Section 9.2.5.1 says "Suspending a device with more than one function
effectively suspends all the functions within the device." I interpret
that to mean that putting a device in U3 suspends all functions, and
thus if the host has previously enabled remote wake for those functions,
it should be able to signal a remote wake up on port status changes.
However, hub vendors may have a different interpretation, and it can't
hurt to put the function into suspend before putting the device into U3.
I cannot get an answer out of the USB 3.0 spec architects about this
ambiguity, so I'm erring on the safe side and always suspending the
first function before placing the device in U3. Note, this code should
be fixed if we ever find any USB 3.0 devices that have more than one
function.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When the USB 3.0 hub support went in, I disabled selective suspend for
all external USB 3.0 hubs because they used a different mechanism to
enable remote wakeup. In fact, other USB 3.0 devices that could signal
remote wakeup would have been prevented from going into suspend because
they would have stalled the SetFeature Device Remote Wakeup request.
This patch adds support for the USB 3.0 way of enabling remote wake up
(with a SetFeature Function Suspend request), and enables selective
suspend for all hubs during hub_probe. It assumes that all USB 3.0 have
only one "function" as defined by the interface association descriptor,
which is true of all the USB 3.0 devices I've seen so far. FIXME if
that turns out to change later.
After a device signals a remote wakeup, it is supposed to send a Device
Notification packet to the host controller, signaling which function
sent the remote wakeup. The host can then put any other functions back
into function suspend. Since we don't have support for function suspend
(and no devices currently support it), we'll just assume the hub
function will resume the device properly when it received the port
status change notification, and simply ignore any device notification
events from the xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Intel has a PCI USB xhci host controller on a new platform. It doesn't
have a line IRQ definition in BIOS. The Linux driver refuses to
initialize this controller, but Windows works well because it only depends
on MSI.
Actually, Linux also can work for MSI. This patch avoids the line IRQ
checking for USB3 HCDs in usb core PCI probe. It allows the xHCI driver
to try to enable MSI or MSI-X first. It will fail the probe if MSI
enabling failed and there's no legacy PCI IRQ.
This patch should be backported to kernels as old as 2.6.32.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Hubs have a flag to indicate whether a given port carries removable devices
or not. This is not strictly accurate in that some built-in devices
will be flagged as removable, but followup patches will make use of platform
data to make this more reliable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace may want to make policy decisions based on whether or not a
given USB device is removable. Add a per-device member and support
for exposing it in sysfs. Information sources to populate it will be
added later.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
People have complained that debugging code shouldn't alter the flow of
control; it should restrict itself to printing out warnings and error
messages. Bowing to popular opinion, this patch (as1518) changes the
debugging checks in usb_submit_urb() to follow this guideline.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Keith Packard <keithp@keithp.com>
CC: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1514) cleans up some places where new_id and remove_id
sysfs attributes are created and deleted. Handling both attributes in
a single routine rather than a pair of routines makes the code
smaller. It also prevents certain kinds of errors, like one we
currently have in the USB subsystem: The removeid attribute is often
created even when newid isn't (because the driver's no_dynamid_id flag
is set).
In the case of the PCMCIA subsystem, the newid attribute is created
but never explicitly deleted. The patch adds a deletion routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As part of the removal of get_driver()/put_driver(), this patch
(as1511) changes all the places that add dynamic IDs for drivers.
Since these additions are done by writing to the drivers' sysfs
attribute files, and the attributes are removed when the drivers are
unregistered, there is no reason to take an extra reference to the
drivers.
The one exception is the pci-stub driver, which calls pci_add_dynid()
as part of its registration. But again, there's no reason to take an
extra reference here, because the driver can't be unloaded while it is
being registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This eliminates the last instance of a function's behavior
controlled by a parameter as Linus hates such things.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do the cleanup to avoid behaviorial parameters Linus
requested.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
both callers of device_get_devnode() are only interested in lower 16bits
and nobody tries to return anything wider than 16bit anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If a driver does not support the suspend/resume callbacks
it will be forcibly disconnected. There is no reason to check
for support of the callbacks after that.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Guillemot Webcam Hercules Dualpix Exchange camera
has been reported with a second ID.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is in succession of previous patch
commit c842114792
xHCI: Adding #define values used for hub descriptor
Hub descriptors characteristics #defines values are added in
hub_configure() in place of magic numbers as asked by Alan Stern.
And the indentation for switch and case is changed to be same.
Some #defines values are added in ch11.h for defining hub class
protocols and used in hub.c and hcd.c in which magic values were
used for hub class protocols.
Signed-off-by: Aman Deep <amandeep3986@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new field num_mapped_sgs to struct urb so that we have a place to
store the number of mapped entries and can also retain the original
value of entries in num_sgs. Previously, usb_hcd_map_urb_for_dma()
would overwrite this with the number of mapped entries, which would
break dma_unmap_sg() because it requires the original number of entries.
This fixes warnings like the following when using USB storage devices:
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:902 check_unmap+0x4e4/0x695()
ehci_hcd 0000:00:12.2: DMA-API: device driver frees DMA sg list with different entry count [map count=4] [unmap count=1]
Modules linked in: ohci_hcd ehci_hcd
Pid: 0, comm: kworker/0:1 Not tainted 3.2.0-rc2+ #319
Call Trace:
<IRQ> [<ffffffff81036d3b>] warn_slowpath_common+0x80/0x98
[<ffffffff81036de7>] warn_slowpath_fmt+0x41/0x43
[<ffffffff811fa5ae>] check_unmap+0x4e4/0x695
[<ffffffff8105e92c>] ? trace_hardirqs_off+0xd/0xf
[<ffffffff8147208b>] ? _raw_spin_unlock_irqrestore+0x33/0x50
[<ffffffff811fa84a>] debug_dma_unmap_sg+0xeb/0x117
[<ffffffff8137b02f>] usb_hcd_unmap_urb_for_dma+0x71/0x188
[<ffffffff8137b166>] unmap_urb_for_dma+0x20/0x22
[<ffffffff8137b1c5>] usb_hcd_giveback_urb+0x5d/0xc0
[<ffffffffa0000d02>] ehci_urb_done+0xf7/0x10c [ehci_hcd]
[<ffffffffa0001140>] qh_completions+0x429/0x4bd [ehci_hcd]
[<ffffffffa000340a>] ehci_work+0x95/0x9c0 [ehci_hcd]
...
---[ end trace f29ac88a5a48c580 ]---
Mapped at:
[<ffffffff811faac4>] debug_dma_map_sg+0x45/0x139
[<ffffffff8137bc0b>] usb_hcd_map_urb_for_dma+0x22e/0x478
[<ffffffff8137c494>] usb_hcd_submit_urb+0x63f/0x6fa
[<ffffffff8137d01c>] usb_submit_urb+0x2c7/0x2de
[<ffffffff8137dcd4>] usb_sg_wait+0x55/0x161
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This pulls in the latest USB bugfixes and helps a few of the drivers
merge nicer in the future due to changes in both branches.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
