There is no call to platform_get_drvdata() or dev_get_drvdata().
Drop the unnecessary call to dev_set_drvdata().
Other relevant changes:
Use existing variable 'dev' instead of dereferencing it several times
This conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts
used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop dev_set_drvdata()
- Use local variable 'struct device *dev' consistently
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The TCA8418 might be used using different interrupt triggers on various
boards. This is not working so far because the current code forces a
falling edge trigger.
The device tree already provides a trigger type, so let's use whatever it
sets up, and since we can be loaded without DT, keep the old behaviour for
the non-DT case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The clip values need the same swapping as the maximum values if the
sensor axes are swapped.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 50ms delays here to use msleep() and
reduce the load on the hrtimer subsystem.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using counter based retry loops for peripherals results in the delay
being significantly overrun during high-load situations where delay
functions tend to be vary imprecise and overrun there timeouts. So
condition the termination on the actual condition of 2s for the
re-calibration to have been successful.
As this is a very long delay there is no advantage in using
high-resolution timers thus switching this to msleep().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver currently only supports legacy platform data probe. This
change adds device tree support and gets rid of platform data probe code
since no one is actually using mpr121 platform data in the mainline.
The device tree property parsing code is based on the work of
atmel_captouch driver.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver reports input events on their interrupts which are triggered
by the sensor's status register changes. But only single bit change is
reported in the interrupt handler. So if there are multiple bits are
changed at almost the same time, other press or release events are ignored.
This fixes it by detecting all changed bits in the status register.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver reports misc scan input events on the sensor's status
register changes. But the event capability for them was not set in the
device initialization, so these events were ignored.
This change adds the missing event capability.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove unused key_val field in struct mpr121_touchkey.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of using #ifdef, let's mark suspend and resume methods as
__maybe_unused to provide better compile coverage.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Small driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - avoid divide by 0 errors on bad touchscreen data
Input: adxl34x - make it enumerable in ACPI environment
Input: ALPS - fix TrackStick Y axis handling for SS5 hardware
Input: synaptics-rmi4 - fix F03 build error when serio is module
Input: xpad - use correct product id for x360w controllers
Input: synaptics_i2c - change msleep to usleep_range for small msecs
Input: i8042 - add Pegatron touchpad to noloop table
Input: joydev - remove unused linux/miscdevice.h include
The Moorestown support was removed by commit 1a8359e411 ("x86/mid: Remove
Intel Moorestown").
Remove this leftover.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
msleep(1~20) may not do what the caller intends, and will often sleep
longer (~20 ms actual sleep for any value given in the 1~20ms range). This
is not the desired behaviour for many cases like device resume time, device
suspend time, device enable time, retry logic, etc. Thus, change msleep to
usleep_range for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Acked-by: Simon Budig <simon.budig@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The order of endpoints is well defined on official Xbox pads, but
we have found at least one 3rd-party pad that doesn't follow the
standard ("Titanfall 2 Xbox One controller" 0e6f:0165).
Fortunately, we get lucky with this specific pad because it uses
endpoint addresses that differ only by direction. We know that
there are other pads out where this is not true, so let's go
ahead and fix this.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace first goto with simple returns as we really are just returning
one error code.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
xbox one was the only device that has a *_process_buttons routine.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ACPI-enabled platform may contain _DSD method to enable this driver
using compatible string.
Remove OF specifics to re-use existing code on ACPI-enabled platforms.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A minus character was lost in commit 23fce365, causing the Y axis to be
inverted for SS5 TrackStick events. (Pushing the TrackStick up caused
the pointer to move down, and vice versa.) Restore the lost minus.
Fixes: 23fce365c6 ("Input: ALPS - clean up code for SS5 hardware")
Signed-off-by: Paul Donohue <linux-kernel@PaulSD.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
rmi_dev is currently being dereferenced before it null checked, however,
after deeper inspecting, rmi_dev can never be null, so just remove this
redundant check.
Fixes CoverityScan CID 1391218 ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
version is a u8, the check for version > 0 means that version can only
be zero, so the subsequent check for version != 0 is never true and
hence is redudant code and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no need to repeat "depends on RMI4_CORE" on every bit of RMI4
support, we can guard all of them at once with "if RMI4_CORE".
Also use tabs for F03 indentation.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
msleep (1~20) may not do what the caller intends, and will often sleep
longer. (~20 ms actual sleep for any value given in the 1~20ms range) This
is not the desired behaviour for many cases like device resume time, device
suspend time, device enable time, etc. Thus, change msleep to usleep_range
for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Acked by: Albert Zhang <xu.zhang@bosch-sensortec.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since F03 is a boolean, "depends" on symbols that can be modules
do not work quite right. We can enable F03 if SERIO is built-in or
if both RMI core and SERIO core are modules. If SERIO core is module,
but RMI is built-in, we'll get:
drivers/built-in.o: In function `rmi_f03_attention':
rmi_f03.c:(.text+0xf8ef8): undefined reference to `serio_interrupt'
rmi_f03.c:(.text+0xf8fbd): undefined reference to `serio_interrupt'
drivers/built-in.o: In function `rmi_f03_remove':
rmi_f03.c:(.text+0xf9082): undefined reference to `serio_unregister_port'
drivers/built-in.o: In function `rmi_f03_probe':
rmi_f03.c:(.text+0xf9260): undefined reference to `__serio_register_port'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
currently the controllers get the same product id as the wireless
receiver. However the controllers actually have their own product id.
The patch makes the driver expose the same product id as the windows
driver.
This improves compatibility when running applications with WINE.
see https://github.com/paroj/xpad/issues/54
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fixes from Ingo Molnar:
"There's a number of fixes:
- a round of fixes for CPUID-less legacy CPUs
- a number of microcode loader fixes
- i8042 detection robustization fixes
- stack dump/unwinder fixes
- x86 SoC platform driver fixes
- a GCC 7 warning fix
- virtualization related fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
Revert "x86/unwind: Detect bad stack return address"
x86/paravirt: Mark unused patch_default label
x86/microcode/AMD: Reload proper initrd start address
x86/platform/intel/quark: Add printf attribute to imr_self_test_result()
x86/platform/intel-mid: Switch MPU3050 driver to IIO
x86/alternatives: Do not use sync_core() to serialize I$
x86/topology: Document cpu_llc_id
x86/hyperv: Handle unknown NMIs on one CPU when unknown_nmi_panic
x86/asm: Rewrite sync_core() to use IRET-to-self
x86/microcode/intel: Replace sync_core() with native_cpuid()
Revert "x86/boot: Fail the boot if !M486 and CPUID is missing"
x86/asm/32: Make sync_core() handle missing CPUID on all 32-bit kernels
x86/cpu: Probe CPUID leaf 6 even when cpuid_level == 6
x86/tools: Fix gcc-7 warning in relocs.c
x86/unwind: Dump stack data on warnings
x86/unwind: Adjust last frame check for aligned function stacks
x86/init: Fix a couple of comment typos
x86/init: Remove i8042_detect() from platform ops
Input: i8042 - Trust firmware a bit more when probing on X86
x86/init: Add i8042 state to the platform data
...
The error message "Can't read CTR while initializing i8042" appears on
Cherry Trail-based devices at each boot time:
i8042: PNP: No PS/2 controller found. Probing ports directly.
i8042: Can't read CTR while initializing i8042
i8042: probe of i8042 failed with error -5
This happens because we historically do not trust firmware on X86 and,
while noting that PNP does not show keyboard or mouse devices, we still
charge ahead and try to probe the controller. Let's relax this a bit and if
results of PNP probe agree with the results of platform
initialization/quirks conclude that there is, in fact, no i8042.
While at it, let's avoid using x86_platform.i8042_detect() and instead
abort execution early if platform indicates that it can not possibly have
i8042 (x86_platform.legacy.i8042 equals X86_LEGACY_I8042_PLATFORM_ABSENT).
Reported-and-tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Cc: linux-input@vger.kernel.org
Link: http://lkml.kernel.org/r/1481317061-31486-3-git-send-email-dmitry.torokhov@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We rely on the result of scanning PNP bus for keyboard and mouse devices to
decide whether we should continue initialization of i8042 driver or not, so
the probes can not be asynchronous.
Also, it is not a good idea to unbind either of the PNP devices while i8042
is running, so let's disable bind/unbind for the PNP drivers through sysfs
and rely on i8042 cleaning after itself properly. User can still unbind and
rebind entire i8042 and that will take care of PNP drivers as well.
Reviewed-by: Luis R. Rodriguez <mgrof@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
msleep(1~20) may not do what the caller intends, and will often sleep longer.
(~20 ms actual sleep for any value given in the 1~20ms range)
This is not the desired behaviour for many cases like device resume time,
device suspend time, device enable time, retry logic, etc.
Thus, change msleep to usleep_range for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Avoid AUX loopback in Pegatron C15B touchpad, so input subsystem is able
to recognize a Synaptics touchpad in the AUX port.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=93791
(Touchpad is not detected on DNS 0801480 notebook (PEGATRON C15B))
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch remove the inclusion of linux/miscdevice.h for joydev
since it does not use miscdevice.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
- updated support for Synaptics RMI4 devices, including support for
SMBus controllers, firmware update support, sensor tuning, and PS/2
guest support
- ALPS driver now supports tracksticks on SS5 controllers
- i8042 now uses chassis info to skip selftest on Asus laptops as list
of individual models became too unwieldy
- miscellaneous fixes to other drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (67 commits)
Input: imx6ul_tsc - generalize the averaging property
Input: drv260x - use generic device properties
Input: drv260x - use temporary for &client->dev
Input: drv260x - fix input device's parent assignment
Input: synaptics-rmi4 - add support for F34 V7 bootloader
Input: drv260x - fix initializing overdrive voltage
Input: ALPS - fix protcol -> protocol
Input: i8042 - comment #else/#endif of CONFIG_PNP
Input: lpc32xx-keys - fix invalid error handling of a requested irq
Input: synaptics-rmi4 - fix debug for sensor clip
Input: synaptics-rmi4 - store the attn data in the driver
Input: synaptics-rmi4 - allow to add attention data
Input: synaptics-rmi4 - f03 - grab data passed by transport device
Input: synaptics-rmi4 - add support for F03
Input: imx6ul_tsc - convert int to u32
Input: imx6ul_tsc - add mask when set REG_ADC_CFG
Input: synaptics-rmi4 - have only one struct platform data
Input: synaptics-rmi4 - remove EXPORT_SYMBOL_GPL for internal functions
Input: synaptics-rmi4 - remove mutex calls while updating the firmware
Input: drv2667 - fix misuse of regmap_update_bits
...
Make the avarage-samples property a general touchscreen property
rather than imx6ul device specific.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- Support for stereo DAPM controls
- Some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- A new version of the topology ABI; this should be backward compatible
- Updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- New drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- Yet another race fix at disconnection
- Tolerated packet size calculation for some Android devices
- Quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- Improvement of Dell pin fixup mapping
- Quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- Replace all kthread usages with simple works
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=WZeb
-----END PGP SIGNATURE-----
Merge tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- support for stereo DAPM controls
- some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- a new version of the topology ABI; this should be backward
compatible
- updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- new drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- yet another race fix at disconnection
- tolerated packet size calculation for some Android devices
- quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- improvement of Dell pin fixup mapping
- quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- replace all kthread usages with simple works"
* tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (296 commits)
ALSA: hiface: Fix M2Tech hiFace driver sampling rate change
ALSA: usb-audio: Eliminate noise at the start of DSD playback.
ALSA: usb-audio: Add native DSD support for TEAC 501/503 DAC
ASoC: wm_adsp: wm_adsp_buf_alloc should use kfree in error path
ASoC: topology: avoid uninitialized kcontrol_type
ALSA: usb-audio: Add QuickCam Communicate Deluxe/S7500 to volume_control_quirks
ALSA: usb-audio: add implicit fb quirk for Axe-Fx II
ASoC: zte: spdif: correct ZX_SPDIF_CLK_RAT define
ASoC: zte: spdif and i2s drivers are not zx296702 specific
ASoC: rsnd: setup BRGCKR/BRRA/BRRB when starting
ASoC: rsnd: enable/disable ADG when suspend/resume timing
ASoC: rsnd: tidyup ssi->usrcnt counter check in hw_params
ALSA: cs46xx: add a new line
ASoC: Intel: update bxt_da7219_max98357a to support quad ch dmic capture
ASoC: nau8825: disable sinc filter for high THD of ADC
ALSA: usb-audio: more tolerant packetsize
ALSA: usb-audio: avoid setting of sample rate multiple times on bus
ASoC: cs35l34: Simplify the logic to set CS35L34_MCLK_CTL setting
ALSA: hda - Gate the mic jack on HP Z1 Gen3 AiO
ALSA: hda: when comparing pin configurations, ignore assoc in addition to seq
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJYT5HMAAoJELDendYovxMvhNQH/1g/3ahM4JKN8Z0SbjKBEdQm
yj2xOj6cE3l6wMSUblKjZD2DLLhpmcHT/E97Xro/lZQEfQJoMXXWWDFowMU/P1LA
mJxb7Fzq5Wr+6eGSAlIQB270MrpNi/luf+CWHMwVA3V7R3KRXwonOdGQSkISIzCd
tgIydEA3a9r2+HgeIBpZFZ4GcSrJQU75krMyl2tjD1C+jeYVd+zdoj2OnDsZQDZQ
hDWApMpNbpSBAn7JtSSdXWSTBsGH0lUECebeYPhPQ2sX2P6Y8+UCGwA7i6FFdbTa
agXfVSdRz8dCe3k19VcKDAw6nK9BTTMnEeEHmkmygIh6wuHPP44CzigTXIbJoXI=
=zjfm
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Xen features and fixes for 4.10
These are some fixes, a move of some arm related headers to share them
between arm and arm64 and a series introducing a helper to make code
more readable.
The most notable change is David stepping down as maintainer of the
Xen hypervisor interface. This results in me sending you the pull
requests for Xen related code from now on"
* tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (29 commits)
xen/balloon: Only mark a page as managed when it is released
xenbus: fix deadlock on writes to /proc/xen/xenbus
xen/scsifront: don't request a slot on the ring until request is ready
xen/x86: Increase xen_e820_map to E820_X_MAX possible entries
x86: Make E820_X_MAX unconditionally larger than E820MAX
xen/pci: Bubble up error and fix description.
xen: xenbus: set error code on failure
xen: set error code on failures
arm/xen: Use alloc_percpu rather than __alloc_percpu
arm/arm64: xen: Move shared architecture headers to include/xen/arm
xen/events: use xen_vcpu_id mapping for EVTCHNOP_status
xen/gntdev: Use VM_MIXEDMAP instead of VM_IO to avoid NUMA balancing
xen-scsifront: Add a missing call to kfree
MAINTAINERS: update XEN HYPERVISOR INTERFACE
xenfs: Use proc_create_mount_point() to create /proc/xen
xen-platform: use builtin_pci_driver
xen-netback: fix error handling output
xen: make use of xenbus_read_unsigned() in xenbus
xen: make use of xenbus_read_unsigned() in xen-pciback
xen: make use of xenbus_read_unsigned() in xen-fbfront
...
Update driver drv260x to use generic device properties so that it can be
used on non-DT systems. We also remove platform data as generic device
properties work on static board code as well.
Signed-off-by: Jingkui Wang <jkwang@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's introduce a temporary for "client->dev" is probe() as we use
it quite a few times and "dev" is shorter.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We were assigning I2C bus controller instead of client as parent device.
Besides being logically wrong, it messed up with devm handling of input
device. As a result we were leaving input device and event node behind
after rmmod-ing the driver, which lead to a kernel oops if one were to
access the event node later.
Let's remove the assignment and rely on devm_input_allocate_device() to
set it up properly for us.
Signed-off-by: Jingkui Wang <jkwang@google.com>
Fixes: 7132fe4f56 ("Input: drv260x - add TI drv260x haptics driver")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Port firmware update code from Samsung Galaxy S7 driver into
mainline framework.
This patch has been tested on Synaptics S7813.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We were accidentally initializing haptics->rated_voltage twice, and did not
initialize overdrive voltage.
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As this define check if huge, this makes easier to read the code.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Semantics of NR_IRQS is different on machines with SPARSE_IRQ option
disabled or enabled, in the latter case IRQs are allocated starting
at least from the value specified by NR_IRQS and going upwards, so
the check of (irq >= NR_IRQ) to decide about an error code returned by
platform_get_irq() is completely invalid, don't attempt to overrule
irq subsystem in the driver.
The change fixes lpc32xx_keys driver initialization on boot:
lpc32xx_keys 40050000.key: failed to get platform irq
lpc32xx_keys: probe of 40050000.key failed with error -22
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The debug would only ever output zero for the clip information.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that we have a proper API to set the attention data, there is
no point in keeping it in the transport driver.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The HID implementation of RMI4 provides the data during
the interrupt (in the input report). We need to provide
a way for this transport driver to provide the attention
data while calling an IRQ.
We use a fifo in rmi_core to not lose any incoming event.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
First check if there are data available passed by the transport device.
If data available use these data. If there are no data available
try to read the rmi block if dsata are passed this way.
This is the way the other rmi function handlers will do this.
This patch is needed on HID devices because the firmware reads F03 data
registers and adds them to the HID attention report. Reading those
registers from the driver after the firmware read them will result in
invalid data.
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds basic functionality for PS/2 passthrough on Synaptics
Touchpads using RMI4 through smbus.
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Lyude Paul <thatslyude@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The name of a codec pin can have an optional prefix string, which is
defined by the SoC machine driver. The snd_soc_dapm_x_pin functions
take the fully-specified name including the prefix and so the existing
code would fail to find the pin if the audio machine driver had added
a prefix.
Switch to using the snd_soc_component_x_pin equivalent functions that
take a specified SoC component and automatically add the name prefix to
the provided pin name.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull input fixes from Dmitry Torokhov: "We are disabling automatic
probing of BYD touchpads as it results in too many false positives,
and the hardware is not terribly popular and having the protocol
support does not result in significantly improved user experience.
We also change keycode for KEY_DATA to avoid clashing with
KEY_FASTREVERSE. Luckily this newish code is used by CEC framework
that is still in staging, so it is extremely unlikely that someone has
already started using this keycode"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: change KEY_DATA from 0x275 to 0x277
Input: psmouse - disable automatic probing of BYD touchpads
The code uses of_property_read_u32 and expects positive values. However,
the values are stored in signed int variables. Additionally, the registers
values are also stored in signed variables without a good reason
(readl/writel expect u32).
The only time this caused a real bug was in the new average-samples
property, in which the property is numerically compared and implicitly
expected to be positive.
I believe it's better to change all the properties and registers to u32,
for consistency and warnings reduction.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Reported-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add mask of each function bits of REG_ADC_CFG, and clear these
function bits first, otherwise use '|=' operation may get the
wrong setting which depends on the original value of REG_ADC_CFG.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If struct rmi_device_platform_data contains pointers to other struct,
it gets difficult to allocate a fixed size struct and copy it over between
drivers.
Change the pointers into a struct and change the code in rmi4 accordingly.
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
those functions should not be used outside of rmi_core.ko.
There is no point in exporting them to the world.
It looks like rmi_read_pdt_entry() should be static too.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This partially reverts commit 29fd0ec2bd ("Input: synaptics-rmi4 -
add support for F34 device reflash")
irq_mutex should be used only to protect data->current_irq_mask, not
preventing incoming input to be processed while the upgrade of the
firmware is happening. We can simply disable the irqs when we don't
want them to interfere with the upgrade process.
Tested on S7300 and S7800 (with F34 v7 patch added)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using regmap_update_bits(..., mask, 1) with 'mask' following (1 << k)
and k greater than 0 is wrong. Indeed, _regmap_update_bits will perform
(mask & 1), which results in 0 if LSB of mask is 0. Thus the call
regmap_update_bits(..., mask, 1) is in reality equivalent to
regmap_update_bits(..., mask, 0).
In such a case, the correct use is regmap_update_bits(..., mask, mask).
This driver is performing such a mistake with the DRV2667_STANDBY mask,
which equals (1 << 6). Fix the driver to make it consistent with the
API, and fix the alignment problem at the same time. Please note that
this change is untested, as I do not have this piece of hardware.
Testers are welcome!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using regmap_update_bits(..., mask, 1) with 'mask' following (1 << k)
and k greater than 0 is wrong. Indeed, _regmap_update_bits will perform
(mask & 1), which results in 0 if LSB of mask is 0. Thus the call
regmap_update_bits(..., mask, 1) is in reality equivalent to
regmap_update_bits(..., mask, 0).
In such a case, the correct use is regmap_update_bits(..., mask, mask).
This driver is performing such a mistake with the DRV2665_STANDBY mask,
which equals BIT(6). Fix the driver to make it consistent with the API,
and fix the alignment problem at the same time. Please note that this
change is untested, as I do not have this piece of hardware. Testers
are welcome!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Set the .enabled boolean and trigger an event processing when enabling
for edge-triggered systems.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The return value of alps_get_pkt_id_ss4_v2() should really be "enum
SS4_PACKET_ID", not "unsigned char". Correct this.
Also, most of the Alps SS5 (SS4 v2) packet byte parsing code is implemented
using macros, but there are a few places where bytes are directly
manipulated in alps.c. For consistency, migrate the rest of these to
macros.
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Paul Donohue <linux-kernel@PaulSD.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For consistency and clarity, the input_report_*() functions should be
called by alps_process_packet_ss4_v2() instead of by alps_decode_ss4_v2().
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Paul Donohue <linux-kernel@PaulSD.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current Alps SS5 (SS4 v2) code generates bogus TouchPad events when
TrackStick packets are processed.
This causes the xorg synaptics driver to print
"unable to find touch point 0" and
"BUG: triggered 'if (priv->num_active_touches > priv->num_slots)'"
messages. It also causes unexpected TouchPad button release and re-click
event sequences if the TrackStick is moved while holding a TouchPad
button.
This commit corrects the problem by adjusting alps_process_packet_ss4_v2()
so that it only sends TrackStick reports when processing TrackStick
packets.
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Paul Donohue <linux-kernel@PaulSD.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The i.MX6UL internal touchscreen controller contains an option to
average upon samples. This feature reduces noise from the produced
touch locations.
This patch adds sample averaging support to the imx6ul_tsc device
driver.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unlike previous Xbox pads, the Xbox One pad doesn't have "sticky" rumble
packets. The duration is encoded into the command and expiration is handled
by the pad firmware.
ff-memless needs pseudo-sticky behavior for rumble effects to behave
properly for long duration effects. We already specify the maximum rumble
on duration in the command packets, but it's still only good for about 2.5
seconds of rumble. This is easily reproducible running fftest's sine
vibration test.
It turns out there's a repeat count encoded in the rumble command. We can
abuse that to get the pseudo-sticky behavior needed for rumble to behave as
expected for effects with long duration.
By my math, this change should allow a single ff_effect to rumble for 10
minutes straight, which should be more than enough for most needs.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is the new gamepad that ships with the Xbox One S which
includes Bluetooth functionality.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The PNP0C40 device of the Surface 3 doesn't have any GPIO attached to it.
Instead of trying to access the GPIO, request the count beforehand and
bail out if it is null or if an error is returned.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gpio_keys will later use gpio_is_valid(). To match the actual
behavior, we should use it here too.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the power supply framework provides a way to store and retrieve
private supply data, use it.
In the process, change the platform data for wm97xx_battery from a
container of a single struct wm97xx_batt_pdata to the direct point to wm97xx_batt_pdata.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
F54 diagnostics report functions provide data based on the number of
enabled rx and tx electrodes, which is not identical to the number of
electrodes reported with F54:Query0 and F54:Query1. Those values report
the number of supported electrodes, not the number of enabled electrodes.
The number of enabled electrodes can be determined by analyzing F55:Ctrl1
(sensor receiver assignment) and F55:Ctrl2 (sensor transmitter assignment).
Propagate the number of enabled electrodes from F55 to F54 to avoid
corrupted output if not all electrodes are enabled.
Fixes: 3a762dbd53 ("[media] Input: synaptics-rmi4 - add support for F54 ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sensor tuning support is needed to determine the number of enabled
tx and rx electrodes for use in F54 functions.
The number of enabled electrodes is not identical to the total number
of electrodes as reported with F55:Query0 and F55:Query1. It has to be
calculated by analyzing F55:Ctrl1 (sensor receiver assignment) and
F55:Ctrl2 (sensor transmitter assignment).
Support for additional sensor tuning functions may be added later.
Fixes: 3a762dbd53 ("[media] Input: synaptics-rmi4 - add support for F54 ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for updating firmware, triggered by a sysfs attribute.
This patch has been tested on Synaptics S7300.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 700a38b27e ("Input: gpio_keys - switch to using generic device
properties") switched to use generic device properties for GPIO keys and
commit 5feeca3c1e ("Input: gpio_keys - add support for GPIO descriptors")
switched from legacy GPIO numbers to GPIO descriptors.
Previously devm_gpio_request_one was explicitly passed GPIOF_DIR_IN flag
to set the GPIO direction as input. However devm_get_gpiod_from_child
doesn't have such provisions and hence fwnode_get_named_gpiod can't set
it as input.
This breaks few platforms with the following error:
" gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
unable to lock HW IRQ <n> for IRQ
genirq: Failed to request resources for POWER (irq <x>) on irqchip
gpio_keys: Unable to claim irq <x>; error -22
gpio-keys: probe failed with error -22 "
This patch fixes the issue by setting input direction explicitly for
gpio lines described by generic properties.
Fixes: 700a38b27e ("Input: gpio_keys - switch to using generic device properties")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should unlock before returning on this error path.
Fixes: 3a762dbd53 ('[media] Input: synaptics-rmi4 - add support for F54 diagnostics')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
BYD automatic protocol detection is extremely unreliable and is often
triggers false positives on regular mice, Sentelic touchpads, and other
devices. BYD has several documents that have recommended detection
sequence, but they conflict with each other and, as far as I can see, still
would not produce unique enough output to reliably differentiate BYD from
other PS/2 devices.
OEMs sourcing BYD devices also do not do us any favors by not supplying any
reasonable DMI data and instead leaving turds like "To Be Filled By O.E.M."
in place of vendor data, or "System Serial Number" as serial number.
On top of that BYD is not truly modern multitouch controller, but rather a
single-touch transitional device that only reports absolute coordinates at
the beginning of finger contact and then reverts to reporting
displacements, and thus not very precise; the only benefit from using BYD
mode vs the legacy PS/2 mode is possibility of edge scrolling.
Given the above, and the fact that BYD devices are somewhat uncommon, let's
disable automatic detection of BYD devices. Users who know they have BYD
trackpads or want to experiment can attempt to activate BYD protocol via
sysfs:
echo -n "byd" > /sys/bus/serio/devices/serio1/drvctl
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=151691
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=175421
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=120781
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=121281
Fixes: 98ee377144 ("Input: byd - add BYD PS/2 touchpad driver")
Cc: stable@vger.kernel.org # 4.6+
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Trivial fix to spelling mistake "failied" to "failed" in
dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some tablets the touchscreen controller is powered by separate
regulators, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit ef3714fdbc ("Input: bma150 - extend chip detection for bma180"),
adds bma180 chip-ids to the input bma150 driver, assuming that they are
100% compatible, but the bma180 is not compatible with the bma150 at all,
it has 14 bits resolution instead of 10, and it has quite different
control registers too.
Treating the bma180 as a bma150 wrt its data registers will just result
in throwing away the lowest 4 bits, which is not too bad. But the ctrl
registers are a different story. Things happen to just work but supporting
that certainly does not make treating the bma180 the same as the bma150
right.
Since some setups depend on the evdev interface the bma150 driver offers
on top of the bma180, we cannot simply remove the bma180 ids.
So this commit only removes the bma180 id when the bma180 iio driver,
which does treat the bma180 properly, is enabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The rmi4 2D sensor functions report the tool type via
input_mt_report_slot_state(), but the abs parameter bit has not been
set so the tool type is not reported to userspace. This patch set
the ABS_MT_TOOL_TYPE bit.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implements reading and setting the dribble bit in F12's control registers.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The rmi_f11 driver currently disables dribble packets and the palm detect
gesture for all devices. This patch creates a parameter in the 2d sensor
platform data for controlling this functionality on a per device basis.
For more information on dribble packets:
Commit 05ba999fca ("HID: rmi: disable dribble packets on Synaptics
touchpads")
For more information on the palm detect gesture:
Commit f097deef59 ("HID: rmi: disable palm detect gesture when present")
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 5b65c2a029 ("HID: rmi: check sanity of the incoming report") added
support for handling incomplete HID reports do to the input data being
corrupted in transit. This patch reimplements this functionality in the
function drivers so they can handle getting less valid data then they
expect.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The attn IRQ is related to the chip, rather than the transport, so move
all handling of interrupts to the core driver. This also makes sure that
there are no races between interrupts and availability of the resources
used by the core driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have encountered some RMI4 firmwares where there are blank pages in
between PDT pages which contain functions. This change makes them
correctly enumerate all functions on the device.
Tested on S7817 (has empty page 2).
Signed-off-by: Nick Dyer <nick@shmanahar.org>
[Tested successfully on S7817 and S7300 Synaptics touch controllers]
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make use of the device property API in this driver so that both OF based
systems and ACPI based systems can use this driver.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
GPIO descriptors are the preferred way over legacy GPIO numbers
nowadays. Convert the driver to use GPIO descriptors internally but
still allow passing legacy GPIO numbers from platform data to support
existing platforms.
Based on commits 633a21d80b ("input: gpio_keys_polled: Add support
for GPIO descriptors") and 1ae5ddb6f8 ("Input: gpio_keys_polled -
request GPIO pin as input.").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
for_each_available_child_of_node(node, pp) takes reference to 'pp' and
drops it when attempting next iteration. However if we exit the loop early
we need to drop the reference ourselves.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of using #ifdef, let's mark suspend and resume methods as
__maybe_unused to provide better compile coverage.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It does not matter if given GPIO may sleep or not when reading state,
polling is always done in a non-atomic context, so we should always
be able to simply use gpiod_get_value_cansleep().
Also let's note in the logs when we fail to read gpio state.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 633a21d80b ("input: gpio_keys_polled: Add support for GPIO
descriptors") placed gpio descriptor into gpio_keys_button structure, which
is supposed to be part of platform data and not modifiable by the driver.
To keep the data constant, let's move the descriptor to
gpio_keys_button_data structure instead.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use xenbus_read_unsigned() instead of xenbus_scanf() when possible.
This requires to change the type of the reads from int to unsigned,
but these cases have been wrong before: negative values are not allowed
for the modified cases.
Cc: dmitry.torokhov@gmail.com
Cc: linux-input@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/input/misc/da9063_onkey.ko | grep alias
alias: platform:da9063-onkey
After this patch:
$ modinfo drivers/input/misc/da9063_onkey.ko | grep alias
alias: platform:da9063-onkey
alias: of:N*T*Cdlg,da9062-onkeyC*
alias: of:N*T*Cdlg,da9062-onkey
alias: of:N*T*Cdlg,da9063-onkeyC*
alias: of:N*T*Cdlg,da9063-onkey
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/input/touchscreen/fsl-imx25-tcq.ko | grep alias
After this patch:
$ modinfo drivers/input/touchscreen/fsl-imx25-tcq.ko | grep alias
alias: of:N*T*Cfsl,imx25-tcqC*
alias: of:N*T*Cfsl,imx25-tcq
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
it's always easier to retrieve these information in bug reports when
it is always printed in the dmesg.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Older versions of gcc warn about the tca8418_irq_handler function
as they can't keep track of the variable assignment inside of the
loop when using the -Wmaybe-unintialized flag:
drivers/input/keyboard/tca8418_keypad.c: In function ‘tca8418_irq_handler’:
drivers/input/keyboard/tca8418_keypad.c:172:9: error: ‘reg’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/input/keyboard/tca8418_keypad.c:165:5: note: ‘reg’ was declared here
This is fixed in gcc-6, but it's possible to rearrange the code
in a way that avoids the warning on older compilers as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use product id for firmware name to request compatible firmware.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Copyright header is updated to add DA9061 in its description and the module
description macro is extended to include DA9061.
Minor change to the code, alters dev_dbg() statements to report a generic
"PMIC" instead of DA9063. This device driver is compatible with DA9061,
DA9062 and DA9063.
Kconfig is updated to reflect support for DA9061/62/63.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Trivial fix to typo in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
platform_device_id table is needed for adding the tps65218-pwrbutton
module to the mfd_cell array.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
psmouse->name "Focaltech Touchpad" is an overkill. In xinput it is too long
as "FocaltechPS/2 Focaltech Focaltech Touchpad"
In focaltech_report_state() pointer to psmouse->dev is already stored as
*dev
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of relying on this model zoo let's skip selftest on all newer Asus
laptops (newer as in when they changed "Computer" -> "COMPUTER" in their
DMI data).
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add product_id sysfs attribute and update protocol version to support it.
Signed-off-by: Sangwon Jee <jeesw@melfas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Schenker XMG C504 is a rebranded Gigabyte P35 v2 laptop.
Therefore it also needs a keyboard reset to detect the Elantech touchpad.
Otherwise the touchpad appears to be dead.
With this patch the touchpad is detected:
$ dmesg | grep -E "(i8042|Elantech|elantech)"
[ 2.675399] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.680372] i8042: Attempting to reset device connected to KBD port
[ 2.789037] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.791586] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.813840] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 3.811431] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f0e)
[ 3.825424] psmouse serio1: elantech: Synaptics capabilities query result 0x00, 0x15, 0x0f.
[ 3.839424] psmouse serio1: elantech: Elan sample query result 03, 58, 74
[ 3.911349] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input6
Signed-off-by: Patrick Scheuring <patrick.scheuring.dev@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull some more input subsystem updates from Dmitry Torokhov:
"An update to the ALPS driver to support the V8 protocol with
touchstick, a change for i8042 to skip selftest on many Asus laptops
which helps to keep their touchpads working after resume, and a couple
other driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - skip selftest on ASUS laptops
Input: melfas_mip4 - add ic_name sysfs attribute
Input: melfas_mip4 - add maintainer information
Input: melfas_mip4 - add devicetree binding documentations
Input: elantech - add Fujitsu Lifebook E556 to force crc_enabled
Input: synaptics-rmi4 - fix error handling in I2C transport driver
Input: synaptics-rmi4 - fix error handling in SPI transport driver
Input: ALPS - add V8 protocol documentation
Input: ALPS - set DualPoint flag for 74 03 28 devices
Input: ALPS - allow touchsticks to report pressure
Input: ALPS - handle 0-pressure 1F events
Input: ALPS - add touchstick support for SS5 hardware
Input: elantech - force needed quirks on Fujitsu H760
Input: elantech - fix Lenovo version typo
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX8Zc4AAoJEHm+PkMAQRiGQG8H/2Hd4IwJh75snGY5LAiWt6ra
kGM/SobvLAMtcoxXCeHqf2bZrxa2Zz9tnEzhuLMGaf9a3l79xHa8YumK5KS1JPGV
6lZBvuPi8BIyT0cpYH000e5ehHfhP6pSGJKZ2EuLv43HcBeVZEGAf3/8jSAlNA15
bwFy2ZEkwJGThbnT6au0Y3s9h8LcNjtllu9hjfb+/9oNGvp8r4QhdVodIqIQ4cv6
SeUfv7Pn2LZDMCSaTP9bh2KaR4dwYZHFsVe75x2wND5Sfq7DVBBfFkAoV/RwJDTM
gBc3PNnmzb/tix6ohOrSQnSiGsXv1uASxvHH3RD2zG6g7Aj9Eq/+Z7ZdPu2+o+U=
=U+ef
-----END PGP SIGNATURE-----
Merge tag 'v4.8' into next
Sync up with mainline to bring in I2C host notify changes and other
updates.
Merge more updates from Andrew Morton:
- a few block updates that fell in my lap
- lib/ updates
- checkpatch
- autofs
- ipc
- a ton of misc other things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (100 commits)
mm: split gfp_mask and mapping flags into separate fields
fs: use mapping_set_error instead of opencoded set_bit
treewide: remove redundant #include <linux/kconfig.h>
hung_task: allow hung_task_panic when hung_task_warnings is 0
kthread: add kerneldoc for kthread_create()
kthread: better support freezable kthread workers
kthread: allow to modify delayed kthread work
kthread: allow to cancel kthread work
kthread: initial support for delayed kthread work
kthread: detect when a kthread work is used by more workers
kthread: add kthread_destroy_worker()
kthread: add kthread_create_worker*()
kthread: allow to call __kthread_create_on_node() with va_list args
kthread/smpboot: do not park in kthread_create_on_cpu()
kthread: kthread worker API cleanup
kthread: rename probe_kthread_data() to kthread_probe_data()
scripts/tags.sh: enable code completion in VIM
mm: kmemleak: avoid using __va() on addresses that don't have a lowmem mapping
kdump, vmcoreinfo: report memory sections virtual addresses
ipc/sem.c: add cond_resched in exit_sme
...
On suspend/resume cycle, selftest is executed to reset i8042 controller.
But when this is done in Asus devices, subsequent calls to detect/init
functions to elantech driver fails. Skipping selftest fixes this problem.
An easier step to reproduce this problem is adding i8042.reset=1 as a
kernel parameter. On Asus laptops, it'll make the system to start with the
touchpad already stuck, since psmouse_probe forcibly calls the selftest
function.
This patch was inspired by John Hiesey's change[1], but, since this problem
affects a lot of models of Asus, let's avoid running selftests on them.
All models affected by this problem:
A455LD
K401LB
K501LB
K501LX
R409L
V502LX
X302LA
X450LCP
X450LD
X455LAB
X455LDB
X455LF
Z450LA
[1]: https://marc.info/?l=linux-input&m=144312209020616&w=2
Fixes: "ETPS/2 Elantech Touchpad dies after resume from suspend"
(https://bugzilla.kernel.org/show_bug.cgi?id=107971)
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=JqCR
-----END PGP SIGNATURE-----
Merge tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation improvements: conversion of all non-DocBook documents
to Sphinx and lots of fixes to the uAPI media book
- New PCI driver for Techwell TW5864 media grabber boards
- New SoC driver for ATMEL Image Sensor Controller
- Removal of some obsolete SoC drivers (s5p-tv driver and soc_camera
drivers)
- Addition of ST CEC driver
- Lots of drivers fixes, improvements and additions
* tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
[media] ttusb_dec: avoid the risk of go past buffer
[media] cx23885: Fix some smatch warnings
[media] si2165: switch to regmap
[media] si2165: use i2c_client->dev instead of i2c_adapter->dev for logging
[media] si2165: Remove legacy attach
[media] cx231xx: attach si2165 driver via i2c_client
[media] cx231xx: Prepare for attaching new style i2c_client DVB demod drivers
[media] cx23885: attach si2165 driver via i2c_client
[media] si2165: support i2c_client attach
[media] si2165: avoid division by zero
[media] rcar-vin: add R-Car gen2 fallback compatibility string
[media] lgdt3306a: remove 20*50 msec unnecessary timeout
[media] cx25821: Remove deprecated create_singlethread_workqueue
[media] cx25821: Drop Freeing of Workqueue
[media] cxd2841er: force 8MHz bandwidth for DVB-C if specified bw not supported
[media] redrat3: hardware-specific parameters
[media] redrat3: remove hw_timeout member
[media] cxd2841er: BER and SNR reading for ISDB-T
[media] dvb-usb: avoid link error with dib3000m{b,c|
[media] dvb-usb: split out common parts of dibusb
...
Another Lifebook machine that needs the same quirk as other similar
models to make the driver working.
Also let's reorder elantech_dmi_force_crc_enabled list so LIfebook enries
are in alphabetical order.
Reported-by: William Linna <william.linna@gmail.com>
Tested-by: William Linna <william.linna@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"You will get
- a new driver for Elan eKTF2127 touchscreen controllers
- a new "gpio-decoder" driver to read and report state of several
GPIO lines
- an ADC resistor ladder driver
- the ft6326 driver is removed because edt-ft5x06 handles the same
devices just fine.
.. plus the regular slew of driver fixes/enhancements"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (26 commits)
Input: elan_i2c - fix return tests of i2c_smbus_read_block_data()
Input: ektf2127 - mark PM functions as __maybe_unused
Input: snvs_pwrkey - drop input_free_device call if input_register_device fails
Input: add support for Elan eKTF2127 touchscreen controller
Input: serio - add hangup support
Input: tps65218-pwrbutton - add support for tps65217 variant
Input: jornada720_ts - get rid of mach/irqs.h and mach/hardware.h includes
Input: jornada720_kbd - remove unneeded mach/hardware.h include
Input: focaltech - mark focaltech_set_resolution() static
Input: wdt87xx_i2c - fix the flash erase issue
Input: gpio-keys-polled - don't use unit-address with button nodes
Input: add generic input driver to read encoded GPIO lines
Input: add ADC resistor ladder driver
Input: pegasus_notetaker - directly include workqueue header
Input: elants_i2c - get product id on recovery mode for FW update
Input: wm97xx - remove deprecated create_singletheread_workqueue
Input: mc13783_ts - remove deprecated create_singletheread_workqueue
Input: psmouse - remove deprecated create_singletheread_workqueue
Input: jornada720_kbd - switch to using dev_dbg
Input: jornada720_kbd - get rid of mach/irqs.h include
...
- Add the MFD bindings doc to MAINTAINERS
- New Drivers
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
- New Device Support
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
- New Functionality
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
- Fix-ups
- Clean-up defunct author emails; da9063, max14577
- Kconfig fixups; wm8350-i2c, as3722
- Constify; altera-a10sr, sm501
- Supply PCI IDs; intel-lpss-pci
- Improve clocking; qcom_rpm
- Fix IRQ probing; ucb1x00-core
- Ensure fault log is cleared; da9052
- Remove NO_IRQ check; ucb1x00-core
- Supply I2C properties; intel-lpss-acpi, intel-lpss-pci
- Non standard declaration; tps65217, max8997-irq
- Remove unused code; lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi
- Make non-modular; altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core,
- OF bindings; ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808,
axp20x, lp873x, exynos5433-lpass, act8945a,
aspeed-scu, twl6040, arizona
- Bug Fixes
- Release OF pointer; qcom_rpm
- Avoid double shifting in suspend/resume; 88pm80x
- Fix 'defined but not used' error; exynos-lpass
- Fix 'sleeping whilst attomic'; atmel-hlcdc
-----BEGIN PGP SIGNATURE-----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=Ja7p
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core framework:
- Add the MFD bindings doc to MAINTAINERS
New drivers:
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
New device support:
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
New functionality:
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
Fix-ups:
- Clean-up defunct author emails (da9063, max14577)
- Kconfig fixups (wm8350-i2c, as37220
- Constify (altera-a10sr, sm501)
- Supply PCI IDs (intel-lpss-pci)
- Improve clocking (qcom_rpm)
- Fix IRQ probing (ucb1x00-core)
- Ensure fault log is cleared (da9052)
- Remove NO_IRQ check (ucb1x00-core)
- Supply I2C properties (intel-lpss-acpi, intel-lpss-pci)
- Non standard declaration (tps65217, max8997-irq)
- Remove unused code (lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi)
- Make non-modular (altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core)
- OF bindings (ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808, axp20x,
lp873x, exynos5433-lpass, act8945a, aspeed-scu, twl6040, arizona)
Bugfixes:
- Release OF pointer (qcom_rpm)
- Avoid double shifting in suspend/resume (88pm80x)
- Fix 'defined but not used' error (exynos-lpass)
- Fix 'sleeping whilst attomic' (atmel-hlcdc)"
* tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: arizona: Handle probe deferral for reset GPIO
mfd: arizona: Remove arizona_of_get_named_gpio helper function
mfd: arizona: Add DT options for max_channels_clocked and PDM speaker config
mfd: twl6040: Register child device for twl6040-pdmclk
mfd: cros_ec_spi: Remove unused variable 'request'
mfd: omap-usb-host: Return value is not 'const int'
mfd: ab8500-debugfs: Remove 'weak' function suspend_test_wake_cause_interrupt_is_mine()
mfd: ab8500-debugfs: Remove ab8500_dump_all_banks_to_mem()
mfd: db8500-prcmu: Remove unused *prcmu_set_ddr_opp() calls
mfd: ab8500-debugfs: Prevent initialised field from being over-written
mfd: max8997-irq: 'inline' should be at the beginning of the declaration
mfd: rk808: Fix RK818_IRQ_DISCHG_ILIM initializer
mfd: tps65217: Fix nonstandard declaration
mfd: lp873x: Remove unused mutex lock from struct lp873x
mfd: atmel-hlcdc: Do not sleep in atomic context
mfd: exynos-lpass: Mark PM functions as __maybe_unused
mfd: intel-lpss: Add default I2C device properties for Apollo Lake
mfd: twl-core: Make it explicitly non-modular
mfd: sun6i-prcm: Make it explicitly non-modular
mfd: smsc-ece1099: Make it explicitly non-modular
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX8Zc4AAoJEHm+PkMAQRiGQG8H/2Hd4IwJh75snGY5LAiWt6ra
kGM/SobvLAMtcoxXCeHqf2bZrxa2Zz9tnEzhuLMGaf9a3l79xHa8YumK5KS1JPGV
6lZBvuPi8BIyT0cpYH000e5ehHfhP6pSGJKZ2EuLv43HcBeVZEGAf3/8jSAlNA15
bwFy2ZEkwJGThbnT6au0Y3s9h8LcNjtllu9hjfb+/9oNGvp8r4QhdVodIqIQ4cv6
SeUfv7Pn2LZDMCSaTP9bh2KaR4dwYZHFsVe75x2wND5Sfq7DVBBfFkAoV/RwJDTM
gBc3PNnmzb/tix6ohOrSQnSiGsXv1uASxvHH3RD2zG6g7Aj9Eq/+Z7ZdPu2+o+U=
=U+ef
-----END PGP SIGNATURE-----
Merge tag 'v4.8' into patchwork
Linux 4.8
* tag 'v4.8': (1761 commits)
Linux 4.8
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems
include/linux/property.h: fix typo/compile error
ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock()
mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()
MAINTAINERS: Switch to kernel.org email address for Javi Merino
x86/entry/64: Fix context tracking state warning when load_gs_index fails
x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUID
x86/vdso: Fix building on big endian host
x86/boot: Fix another __read_cr4() case on 486
sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock
sctp: change to check peer prsctp_capable when using prsctp polices
sctp: remove prsctp_param from sctp_chunk
sctp: move sent_count to the memory hole in sctp_chunk
tg3: Avoid NULL pointer dereference in tg3_io_error_detected()
x86/init: Fix cr4_init_shadow() on CR4-less machines
MIPS: Fix detection of unsupported highmem with cache aliases
MIPS: Malta: Fix IOCU disable switch read for MIPS64
MIPS: Fix BUILD_ROLLBACK_PROLOGUE for microMIPS
...
Instantiating the rmi4 I2C transport driver without interrupts assigned
(for example using manual i2c instantiation from the command line)
caused the driver to fail to load, but it does not clean up its regulator
or transport device registrations. Result is a crash at a later time,
for example when rebooting the system.
Fixes: 946c8432aa ("Input: synaptics-rmi4 - support regulator supplies")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instantiating the rmi4 SPI transport driver without an interrupt assigned
caused the driver to fail to load, but it does not clean up its transport
device registration. Result may be a crash at a later time, for example
when rebooting the system.
Fixes: 8d99758dee ("Input: synaptics-rmi4 - add SPI transport driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here we introduce logic in alps_identify to set the ALPS_DUALPOINT flag
for touchpad hardware responding to E7 report with 73 03 28, as is found
in the Dell Latitude E7470.
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The SS5 hardware can report this.
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
While a button is held SS5 hardware will give us single-finger packets
with x, y, and pressure equal to zero. This causes annoying jumps in
pointer position if a touch is released while the button is held. Handle
this by claiming zero contacts to ensure that no position events are
provided to the user.
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add touchstick support for the so-called SS5 hardware, which uses a
variant of the SS4 protocol.
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems that
flow through me. Nothing major that I can discern, full details are in
the shortlog.
All have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFUEABECABYFAlfyOIQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfsp9OQAlRy3
gSKfQUlXjTs96Bx/I5PtWysAn0r8nyKZoP1oSgsTddOCEeXngTXc
=4uPs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems
that flow through me. Nothing major that I can discern, full details
are in the shortlog.
All have been in the linux-next tree with no reported issues"
* tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (144 commits)
drivers/misc/hpilo: Changes to support new security states in iLO5 FW
at25: fix debug and error messaging
misc/genwqe: ensure zero initialization
vme: fake: remove unexpected unlock in fake_master_set()
vme: fake: mark symbols static where possible
spmi: pmic-arb: Return an error code if sanity check fails
Drivers: hv: get rid of id in struct vmbus_channel
Drivers: hv: make VMBus bus ids persistent
mcb: Add a dma_device to mcb_device
mcb: Enable PCI bus mastering by default
mei: stop the stall timer worker if not needed
clk: probe common clock drivers earlier
vme: fake: fix build for 64-bit dma_addr_t
ttyprintk: Neaten and simplify printing
mei: me: add kaby point device ids
coresight: tmc: mark symbols static where possible
coresight: perf: deal with error condition properly
Drivers: hv: hv_util: Avoid dynamic allocation in time synch
fpga manager: Add hardware dependency to Zynq driver
Drivers: hv: utils: Support TimeSync version 4.0 protocol samples.
...
Just like Fujitsu CELSIUS H730, the H760 also has an Elantech touchpad with
the same quirks. Without this patch, the touchpad is useless out-of-the-box
as the mouse pointer won't move.
This patch makes the driver aware of both the crc_enabled=1 requirement and
the middle button, making the touchpad fully functional out-of-the-box.
Signed-off-by: Matti Kurkela <Matti.Kurkela@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Reviewed-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i2c_smbus_read_block_data() returns negative errno else the number of
data bytes in the slave's response.
Checking for error not null means the function always fails if the device
answers properly.
So given that we read 3 bytes and access those, better check that we
actually read those 3 bytes.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The newly added ektf2127 driver uses the SIMPLE_DEV_PM_OPS macro
to conditionally refer to the resume/suspend functions, which
causes a warning when CONFIG_PM_SLEEP is disabled:
drivers/input/touchscreen/ektf2127.c:168:12: error: 'ektf2127_resume' defined but not used [-Werror=unused-function]
drivers/input/touchscreen/ektf2127.c:156:12: error: 'ektf2127_suspend' defined but not used [-Werror=unused-function]
We could either put these functions inside of an #ifdef or
add __maybe_unused annotations. This uses the second approach,
which is generally more foolproof.
Fixes: 9ca5bf5029 ("Input: add support for Elan eKTF2127 touchscreen controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fix from Dmitry Torokhov:
"One small change to make joydev (which is used by older games) to bind
to devices that export Z axis but not X or Y (such as TRC rudder)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: joydev - recognize devices with Z axis as joysticks
Current implementation of joydev's input_device_id table recognizes only
devices with ABS_X, ABS_WHEEL or ABS_THROTTLE axes as joysticks.
There are joystick devices that do not have those axes, for example TRC
Rudder device. The device in question has ABS_Z, ABS_RX and ABS_RY axes
causing it not being detected as joystick.
This patch adds ABS_Z to the input_device_id list allowing devices with
ABS_Z axis to be detected correctly.
Signed-off-by: Ville Ranki <ville.ranki@iki.fi>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Current code uses devm_input_allocate_device() so don't explicitly call
input_free_device if input_register_device fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds a driver for the Elan eKTF2127 touchscreen controller,
which speaks an i2c protocol which is distinctly different from
the already supported eKTH controllers.
Signed-off-by: Michel Verlaan <michel.verl@gmail.com>
Signed-off-by: Siebren Vroegindeweij <siebren.vroegindeweij@hotmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Just a fix up for the firmware handling to the Silead driver (which is
a new driver in this release)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: silead_gsl1680 - use "silead/" prefix for firmware loading
Input: silead_gsl1680 - document firmware-name, fix implementation
The Pulse-Eight USB CEC adapter is a usb device that shows up as a ttyACM0
device. It requires that you run inputattach in order to communicate with
it via serio.
This all works well, but it would be nice to have a udev rule to
automatically start inputattach. That too works OK, but the problem comes
when the USB device is unplugged: the tty hangup is never handled by the
serio framework so the inputattach utility never exits and you have to kill
it manually.
By adding this hangup callback the inputattach utility now properly exits
as soon as the USB device is unplugged.
The udev rule I used on my Debian sid system is:
SUBSYSTEM=="tty", KERNEL=="ttyACM[0-9]*", ATTRS{idVendor}=="2548", ATTRS{idProduct}=="1002", ACTION=="add", TAG+="systemd", ENV{SYSTEMD_WANTS}+="pulse8-cec-inputattach@%k.service"
And /etc/systemd/system/pulse8-cec-inputattach@.service is as follows:
===============================================================
[Unit]
Description=inputattach for pulse8-cec device on %I
[Service]
Type=simple
ExecStart=/usr/local/bin/inputattach --pulse8-cec /dev/%I
KillMode=process
===============================================================
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add copyright lines for Zodiac who paid for the V4L touch work.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The newly added debug mode for the synaptics-rmi4 driver relies on
the v4l2 interface and vb2_vmalloc, but those might be configured
as loadable modules when the driver itself is built-in, resulting
in a link failure:
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_remove':
rmi_f54.c:(.text.rmi_f54_remove+0x14): undefined reference to `video_unregister_device'
rmi_f54.c:(.text.rmi_f54_remove+0x20): undefined reference to `v4l2_device_unregister'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_s_input':
rmi_f54.c:(.text.rmi_f54_vidioc_s_input+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_g_input':
rmi_f54.c:(.text.rmi_f54_vidioc_g_input+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_fmt':
rmi_f54.c:(.text.rmi_f54_vidioc_fmt+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_enum_input':
rmi_f54.c:(.text.rmi_f54_vidioc_enum_input+0x10): undefined reference to `video_devdata'
drivers/input/rmi4/rmi_core.o: In function `rmi_f54_vidioc_querycap':
...
The best workaround I could come up with is to disallow the debug
mode unless it's actually possible to call it.
Fixes: 3a762dbd53 ("[media] Input: synaptics-rmi4 - add support for F54 diagnostics")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The newnly added debug mode for the atmel_mxt_ts driver relies on
the v4l2 interface and vb2_vmalloc, but those might be configured
as loadable modules when the driver itself is built-in, resulting
in a link failure:
drivers/input/touchscreen/atmel_mxt_ts.o: In function `mxt_vidioc_querycap':
atmel_mxt_ts.c:(.text.mxt_vidioc_querycap+0x10): undefined reference to `video_devdata'
drivers/input/touchscreen/atmel_mxt_ts.o: In function `mxt_buffer_queue':
atmel_mxt_ts.c:(.text.mxt_buffer_queue+0x20): undefined reference to `vb2_plane_vaddr'
atmel_mxt_ts.c:(.text.mxt_buffer_queue+0x164): undefined reference to `vb2_buffer_done'
drivers/input/touchscreen/atmel_mxt_ts.o: In function `mxt_free_object_table':
atmel_mxt_ts.c:(.text.mxt_free_object_table+0x18): undefined reference to `video_unregister_device'
atmel_mxt_ts.c:(.text.mxt_free_object_table+0x20): undefined reference to `v4l2_device_unregister'
The best workaround I could come up with is to disallow the debug
mode unless it's actually possible to call it.
Fixes: ecfdd7e266 ("[media] Input: atmel_mxt_ts - output diagnostic debug via V4L2 device")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The silead touch-controller ICs use a different firmware per digitizer /
tablet model. So there are going to be quite a few of then and they really
should be under a separate subdir.
This commit prefixes the default firmware names with "silead/" just like
we are already doing for devicetree specified firmware names.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>