The xc5000 datasheet indicates that the reset pin only needs to be held low
for 10ms. Reduce the value accordingly, which speeds up the firmware load
time a bit.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A regression was introduced in hg changeset 33810c734a0d, which resulted in
a kernel panic whenever the device was disconnected from USB. The call to
4l2_device_register() was overwriting the pointer for usb_set_intfdata(), so
when au0828_usb_disconnect() was called, the usb_get_intfdata() returned a
pointer to the v4l2_device instead of the au0828_dev structure.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is no longer needed to use a struct pointer as argument, since v4l2_subdev
doesn't require that ioctl-like approach anymore. Instead just pass the input,
output and config (new!) arguments directly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions v4l2_i2c_new_subdev and v4l2_i2c_new_probed_subdev relied on
i2c_get_adapdata to return the v4l2_device. However, this is not always
possible on embedded platforms. So modify the API to pass the v4l2_device
pointer explicitly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_std didn't belong in the tuner ops. Stricly speaking it should be part of
the video ops, but it is used by audio and tuner devices as well, so it is
more efficient to make it part of the core ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setup the i2c clock speed to be definable on a per-board basis. This allows
us to explicitly set the clock speed to 30 KHz on the 950q, and also gets rid
of code which sets it on a basis of what chip the i2c master is talking to
at any given time (which could have caused issues because i2c slaves should
never receive commands at a clock higher than their supported clock speed).
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the #define entries for the i2c registers to be more meaningful, and
document the valid values for the registers. Note that this changeset makes
*no* functional changes to the code.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add missing URB_NO_TRANSFER_DMA_MAP flag, since the use of consistent memory
is not permitted for DMA on the ARM platform.
Thanks to Paul Thomas <pthomas8589@gmail.com> for providing sample ARM
hardware that was experiencing the oops (tested on the at91rm9200 based
LinuxStamp).
Thanks to David Brownell <david-b@pacbell.net> for providing insight into the
ARM memory architecture.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several Kconfig items using CUSTOMIZE. Yet, most use the English
writing CUSTOMISE. This generates lots of trouble, because people sometimes type
the Kbuild item different.
Let's standardise every occurrence using the same syntax.
The changes were generated by this small shell script:
for i in `find linux -type f`; do sed s,CUSTOMIZE,CUSTOMISE,g $i >/tmp/a && mv /tmp/a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
au8522 is now dependent of V4L2, as reported by Randy Dunlap
<randy.dunlap@oracle.com>:
au8522_decoder.c:(.text+0x199898): undefined reference to `v4l2_ctrl_query_fill'
au8522_decoder.c:(.text+0x1998b3): undefined reference to `v4l2_ctrl_query_fill'
au8522_decoder.c:(.text+0x199944): undefined reference to `v4l2_device_unregister_subdev'
au8522_decoder.c:(.text+0x19997c): undefined reference to `v4l2_chip_ident_i2c_client'
au8522_decoder.c:(.text+0x199f1e): undefined reference to `v4l2_i2c_subdev_init'
Cc: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Kyle McMartin and Randy Dunlap:
drivers/media/video/au0828/au0828-video.c:1438: error: 'const struct v4l2_subdev_core_ops' has no member named 'g_register'
drivers/media/video/au0828/au0828-video.c:1453: error: 'const struct v4l2_subdev_core_ops' has no member named 's_register'
This patch properly implements those two API ioctls only when debug is
enabled.
Cc: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per Hans Verkuil <hverkuil@xs4all.nl> instruction, remove the deprecated
attach_inform/detach_inform routines, and convert over the i2c calls to
subdev calls.
Thanks to Hans Verkuil <hverkuil@xs4all.nl> for providing feedback on the
au0828 analog support.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VBI support or the au0828 has the framework written but it does not yet
work. Rename the macro per Mauro's request.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Take a pass over all of the au0828/au8522 files and cleanup all the codingstyle
issues. This patch does not make *any* functional change to the code.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the sake of completeness, include the "undefined" input type enumeration,
even though there is no path that can actually call it.
Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing this out.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There were some braces left behind from when there was more code in the block.
Remove it.
Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing this out.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The userland callers are responsible for clearing the output buffers, so
remove the unneeded memset calls.
Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing this out.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure newly created v4l2 devices have a unique name, modeling the logic
after the cx18 driver.
Thanks to Andy Walls <awalls@radix.net> for pointing out the issue.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert over to using the new subdev framework for the au0828 bridge. This
includes using the new i2c probing mechanism.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the analog initialization failed to create the video device, we never
actually add the entry to the au0828_devlist. Therefore a panic occurs when
unregistering the analog subsystem.
Make it so we only remove the entry from the list if we added it to the list
in the first place.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is not valid to look for dev->board.input == NULL to detect an undefined
analog configuration section, since it is a member of the struct and not a
pointer (hence it will *always* be non-NULL). Do the check based on whether
the first input is actually a valid input type instead.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for providing sample hardware
of various configurations to test with.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the setup of the analog isoc handler into au0828-video.c, so it does not
occur if there is not an .input section defined for the board. Also fixes a
case where if there is an input section but the board does not actually have
analog support, the digital support will continue to work as expected.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for providing sample hardware
of various configurations to test with.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the g_chip_ident call work for the au0828/au8522. Discovered when testing
with the v4l2_compliance tool
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
[mchehab@redhat.com: fix merge conflict, due to a path change for analog demod]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it a little easier to read the debug messages for register read/write
operations
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a bug where enumerating the i2c for devices would result in false
positives. The root of the issue was the scanning was using SMBUS_QUICK
messages, which are zero length write requests (which our i2c adapter
implementation didn't handle). Because we never strobed any bytes onto the
bus, the status register would still contain the value from the previous
request.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the VBI support is not yet working for the au0828, don't advertise the
capability or create the /dev/vbi device.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't now how to make any variant of NTSC work other than NTSC-M, so don't
advertise that we support the other variants.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rework the way boards are managed so that we can change the board description
based on the Hauppauge eeprom (modeled after cx88-cards.c).
Also, make sure that we don't load the analog stack if there are no analog
inputs defined in the board profile.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for providing information on
the various ways different Hauppauge boards can be configured.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the analog parameters to the device profile for the HVR-850
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is an issue related to the i2c clock for addressing the xc5000. The
au0828 chip does not support clock stretching, which the xc5000 makes use of.
This results in cases where we silently get back garbage in i2c read
operations. To work around this issue until we slow down the i2c clock when
talking with that specific device.
This was not an issue before we had analog support because we never needed to
enumerate the i2c bus, and digital tuning never actually needed to perform
read operations against the xc5000.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the analog functionality found in the au0828 bridge
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
[mchehab@redhat.com: fix compilation by adding linux/version.h]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The name of the option is DVB_FE_CUSTOMISE. However, on a few places, a wrong
name were used, due to a typo (DVB_FE_CUSTOMIZE).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add autodetection support for a new revision of the Hauppauge HVR950Q (2040:721e)
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dont pass devptr in xc5000_attach, dont store it in xc5000_priv.
This pointer is passed into the tuner_callback function, which always
expects a pointer to fe->dvb->priv or i2c_adapter->algo_data.
This prevents future possible bugs in new drivers, such as using a "devptr"
other that the standard fe->dvb->priv in a DVB driver.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I need this so I can better isolate my linux email from my
corporate email.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Explicitly set 6 MHz IF frequency for VSB and QAM in
hauppauge_hvr950q_config.
The default value is 6 MHz, so this patch doesn't change anything --
this only improves code readability and may prevent future bugs.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This code is irrelevant to this driver and should be removed. This was
copied from a hack in cx88-dvb.c, which prevents noise coming from the
analog tuner (via an audio patch cable from the pci card to the sound
hardware) when in digital mode by muting the tda988x. This issue does
not apply to this USB hybrid chip design, where a single piece of
silicon handles both analog and digital demodulation.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The current code passes a context pointer in the xc5000_config struct.
This context pointer is used in the tuner_callback function, used to
reset the device after firmware download.
The xc5000_config struct is a static structure, whose .priv member was
being assigned before calling xc5000_attach(). If there are more than
one of the same device type installed on a single system, the last one
to assign xc5000_config.priv will "win", and all others will cease to
function properly.
This patch passes the context pointer in xc5000_attach() rather that
storing it within the static struct xc5000_config.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
