Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This switches the ab3100 core to use the enable_time()
infrastructure from the regulator core.
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The regulator core had suspend-prepare that turns off the regulators
when entering a system-wide suspend. However, it did not have
suspend-finish that pairs with suspend-prepare and the regulator core
has assumed that the regulator devices and their drivers support
autonomous recover at resume.
This patch adds regulator_suspend_finish that pairs with the
previously-existed regulator_suspend_prepare. The function
regulator_suspend_finish turns on the regulators that have always_on set
or positive use_count so that we can reset the regulator states
appropriately at resume.
In regulator_suspend_finish, if has_full_constraints, it disables
unnecessary regulators.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
Updates
v3
comments corrected (Thanks to Igor)
v2
disable unnecessary regulators (Thanks to Mark)
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix typo: s/TPS695x0/TPS659x0/
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Makes it a bit easier to identify if it's a problem with the supplies,
the usual error would be omitting the supply name entirely.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This adds a subdriver for the regulator found inside the TPS61050
and TPS61052 chips.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch supports PMIC/Regulator part of MAX8997/MAX8966 MFD.
In this initial release, selecting voltages or current-limit
and switching on/off the regulators are supported.
Controlling voltages for DVS with GPIOs is not implemented fully
and requires more considerations: it controls multiple bucks (selection
of 1, 2, and 5) at the same time with SET1~3 gpios. Thus, when DVS-GPIO
is activated, we lose the ability to control the voltage of a single
buck regulator independently; i.e., contolling a buck affects other two
bucks. Therefore, using the conventional regulator framework directly
might be problematic. However, in this driver, we try to choose
a setting without such side effect of affecting other regulators and
then try to choose a setting with the minimum side effect (the sum of
voltage changes in other regulators).
On the other hand, controlling all the three bucks simultenously based
on the voltage set table may help build cpufreq and similar system
more robust; i.e., all the three voltages are consistent every time
without glitches during transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
regulator driver. So move the identification of device node from
regulator driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that mfd-core no longer makes a copy of platform_data, but the
mc13xxx-core driver creates the pdata structures on the stack. In
order to get around that, the various ARM mach types that set the
pdata have been changed to hold the variable in static (global) memory.
Also note that __initdata references in aforementioned pdata structs
have been dropped.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In OMAP4 Blaze and Panda, 32KHz clock to WLAN is supplied from Phoenix
TWL6030. The 32KHz clock state (ON/OFF) is configured in
CLK32KG_CFG_[GRP, TRANS, STATE] register. This follows the same register
programming model as other regulators in TWL6030. So add CLK32KG as pseudo
regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The variable 'val' is a 'unsigned int', so it can never be less than zero.
This fact makes the "val < 0" part of the test done in BUG_ON() in
mc13xxx_regulator_get_voltage() rather pointles since it can never have
any effect.
This patch removes the pointless test.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The previous driver did not support BUCK1-DVS3, BUCK1-DVS4, and
BUCK2-DVS2 modes. This patch adds such modes and an option to block
setting buck1/2 voltages out of the preset values.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The first releases of LP3974 have a large delay in RTC registers,
which requires 2 seconds of delay after writing to a rtc register
(recommended by National Semiconductor's engineers)
before reading it.
If "rtc_delay" field of the platform data is true, the rtc driver
assumes that such delays are required. Although we have not seen
LP3974s without requiring such delays, we assume that such LP3974s
will be released soon (or they have done so already) and they are
supported by "lp3974" without setting "rtc_delay" at the platform
data.
This patch adds delays with msleep when writing values to RTC registers
if the platform data has rtc_delay set.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The index is missing so the return is wrong.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Otherwise, we will not return error if write to MC13892_SWITCHERS5 failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We only expose the use and open counts to userspace, providing a tiny
bit of insight into what the API is up to.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It's a boolean value so use the type.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The recent introduction of standard regulator API logging macros means
that all our log messages have at least the function name in them and
logging that the constraints are for the regulator API is probably a
bit much.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If a consumer sets the same voltage range as is currently configured
for that consumer there's no need to run through setting the voltage
again. This pattern may occur with some CPUfreq implementations where
the same voltage range is used for multiple frequencies.
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When cooperating with an external control source the regulator setup
may be changed underneath the API. Currently consumers can just redo
the regulator_set_voltage() to restore a previously set configuration
but provide an explicit API for doing this as optimsations in the
regulator_set_voltage() implementation will shortly prevent that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
No point exposing functions that aren't used elsewhere to the global
namespace and sparse warns about doing so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently we notify a voltage change whenever we exit set_voltage(),
even if the change failed for some reason (eg, a constraints issue).
This shouldn't cause any substantial ill effects but is wasteful as
listeners get notified on noops. Fix this by moving the notification
into _do_set_voltage() and only notifying if we don't return an error.
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Many regulator drivers implement voltage setting by looping through a
table of possible values, normally because the set of available voltages
can't be mapped onto selectors with simple calcuation. Factor out these
loops by providing a variant of set_voltage() which takes a selector rather
than a voltage range as an argument and implementing a loop through the
available selectors in the core.
This is not going to be suitable for use with all devices as when the
regulator voltage can be mapped onto selector values with a simple
calculation the linear scan through the available values will be more
expensive than just doing the calculation, especially for regulators
that provide fine grained voltage control.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Push all the callers of the chip set_voltage() operation out into a single
function to facilitiate future refactoring.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Since the MFD core for this device and the regulator drivers for these
devices can be built modular we should also support modular build of
the shared code for the regulator drivers, otherwise we try to link
built in code against modular code with unfortunate results.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
move some common functions and micros of mc13783 regulaor driver to
a seperate file, which makes it possible for mc13892 to share code.
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
To make mc13783 and mc13892 share code, the register names should be
changed to fit the new macro definitions in the comming patch.
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch removes the macros for initializing the regulators.
The purpose is to remove one layer of abstraction and make the
code easier to read.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The verbose debug outputs register writes and reads that can be
used to debug the driver.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The regulator enumeration is used for putting the regulator data
in correct place in the info array. This should be matched in the
board configuration.
Variable names are updated to be more consistent, comments are
corrected and macros have been edited to be consistent.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The AUX3 regulator voltage setting is changed in ab8500 v2 compared
to ab8500 v1. This patch adds v2 support while keeping support for
v1.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The find_regulator function was unused so it has been removed. The
ab8500 pointer in the regulator info structure was unused and so it
has also been removed.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
For INTCORE and TVOUT regulators, the low power register bit is
included in the mask so that enable will set the regulator in
normal (high power) mode.
ANAMIC1, ANAMIC2, DMIC regulator settings are swapped with each
other so that the correct regulator gets enabled/disabled.
ANA regulator register address is corrected.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The define for number of regulators is moved from ab8500-core to
ab8500-regulator so that the regulator driver can be updated
independently of ab8500-core. This also changes the platform
configuration structure of ab8500-core so that it contains a
pointer to the regulator_init_data array plus number of
regulators instead of an fixed size array of pointers to
regulator_init_data.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
TPS6524X provides three step-down converters and two general-purpose LDO
voltage regulators. This device is interfaced using SPI.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Since drivers already have to provide an API for translating selectors
into voltages they may as well just report the selector values directly
to the core API rather than implement the lookup themselves. The old
interface is left in place for now, but may be removed in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rather than referencing the get_voltage() operation directly in the
ops struct use the internal _regulator_get_voltage() API call to do
so, facilitating refactoring.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Extend the regulator_set_voltage() function to take into account the
voltage requirements of all consumers of the regulator being changed,
in order to set the voltage to the minimum voltage acceptable to all
consumers. The existing behaviour was that the latest
regulator_set_voltage() call would win over previous
regulator_set_voltage() calls even if setting the voltage to a
non-acceptable level from other consumers.
Signed-off-by: Thomas Petazzoni <t-petazzoni@ti.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
On Tue, 2010-11-30 at 10:52 +0000, Mark Brown wrote:
> On Mon, Nov 29, 2010 at 05:12:56PM -0800, Joe Perches wrote:
> > Just to please broonie...
> > Signed-off-by: Joe Perches <joe@perches.com>
> As usual when fixing review issues please revise your original patch
> rather than posting a fresh patch.
Here's an earlier comment:
On Thu, 2010-11-18 at 13:30 +0000, Mark Brown wrote:
> This looks reasonable, please rebase on top of Daniel's patches and
> submit it properly (with changelog and so on).
Sometimes it's simpler for an upstream maintainer to do
something like:
git am -s <patch1.mbox>
patch -p1 < patch2.mbox
git commit --amend file
instead of back and forthing.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
They're not needed and sparse is verbosely upset about them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently the regulator API uses the constraints structure passed in to
the core throughout the lifetime of the object. This means that it is not
possible to mark the constraints as __initdata so if the kernel supports
many boards the constraints for all of them are kept around throughout the
lifetime of the system, consuming memory needlessly. By copying constraints
that are actually used we allow the use of __initdata, saving memory when
multiple boards are supported.
This also means the constraints can be const.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The version hasn't been updated since the regulator API was merged in
2.6.27 so just remove it - now we're in mainline the kernel version is
much more useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Don't use %s to format fixed static strings into log messages, it just
makes searching for and reading the message in the kernel source
needlessly hard.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The regulator framework uses a lot of printks with a
specific formatting using __func__. This converts them
to use pr_ calls with a central format string.
Cc: bleong@codeaurora.org
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This adds a pr_fmt line which uses the __func__ macro. I also
convert the current pr_ lines to remove their __func__ usage.
Cc: bleong@codeaurora.org
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Supply regulators are disabled only when the last
reference count is removed on the child regulator
(the use count goes from 1 to 0). This patch changes
the behaviour of enable so the supply regulator is
enabled only when the use count of the child
regulator goes from 0 to 1.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide some basic trace facilities to the regulator API. We generate
events on regulator enable, disable and voltage setting over the actual
hardware operations (which are assumed to be the expensive ones which
require interaction with the actual device). This is intended to facilitate
debug of the performance and behaviour with consumers allowing unified
traces to be generated including the regulator operations within the
context of the other components of the system.
For enable we log the explicit delay for the voltage ramp separately to
the interaction with the hardware to highlight the time consumed in I/O.
We should add a similar delay for voltage changes, though there the
relatively small magnitude of the changes in the context of the I/O
costs makes it much less critical for most regulators.
Only hardware interactions are currently traced as the primary focus is
on the performance and synchronisation of actual hardware interactions.
Additional tracepoints for debugging of the logical operations can be
added later if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change the interface used by set_voltage() to report the selected value
to the regulator core in terms of a selector used by list_voltage().
This allows the regulator core to know the voltage that was chosen
without having to do an explict get_voltage(), which would be much more
expensive as it will generally access hardware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch add locks around regulator supply enable.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
LDO2 has a slightly different range of supported voltages on WM8958
so update the selector<->voltage mappings to match.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Correct the register table for SM2, LDO8, RTC
Change-Id: I45348cec5ffbb7da9bd7523764fb611b537236b8
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change-Id: I40400bb65eab496bb1becd26b37a9653b99d4f41
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
(Split into separate patches)
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change-Id: Idacf5e1e51dbbbcd5ea93f310a4e907977e7359e
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
(Split into separate patches)
(Minor formatting fixes)
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change-Id: I76eaceb31b56264f6978af15db1e6fc7e2e01b5a
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
(Split into separate patches)
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix kernel-doc warning for set_consumer_device_supply():
Warning(drivers/regulator/core.c:912): missing initial short description on line:
* set_consumer_device_supply: Bind a regulator to a symbolic supply
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Supply regulators are disabled only when the last
reference count is removed on the child regulator
(the use count goes from 1 to 0). This patch changes
the behaviour of enable so the supply regulator is
enabled only when the use count of the child
regulator goes from 0 to 1.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The Singular Message is 16 bits:
DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0]
Current implementation return immedially after sucessfuly write MSB part.
To properly set mode, we need to write the complete message ( MSB and LSB ).
In twl.h, now we have defines for PM Master module register offsets,
use it instead of hard coded 0x15/0x16.
Use "message & 0xff" to ensure we send correct value for LSB.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Lesly Arackal Manuel <leslyam@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch add locks around regulator supply enable.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Integer division will truncate the result, this patch ensures we have
enough delay time for enabling regulator.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We already have device_remove_file() in error path,
no need to call it before goto link_name_err.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch fixes a disable failure when regulator supply is used.
A while loop in regulator disable checks for supply pointer != NULL
but the pointer is not always updated, resulting in the while loop
running too many times causing a disable failure.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
max8998_pmic_probe:
- modified to check if valid pins are defined at platform
data
- maximal voltage values (predefined at platform data) are uploaded to
max8998 device
max8998_set_voltage_buck:
- BUCK1/2 voltages change between values already defined
- Checks if valid GPIO pins are passed from platform data
- If requested voltage cannot be satisfied from already defined values,
then one of free slots is used
- Predefined maximum voltages (as defined at platform data) are always
available
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
BUCK1/2 internal voltages and indexes defined in the struct max8998_data
max_get_voltage_register now uses index values to chose proper register
More generic BUCK1/2 registers names provided
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the ab8500 mixed signal chip expose the same
interface for register access as the ab3100, ab3550 and ab5500 chip.
The ab8500_read() and ab8500_write() is removed and replaced with
abx500_get_register_interruptible() and
abx500_set_register_interruptible().
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MAX8998 chip have regulator and rtc features. The i2c slave address
of regulator and rtc is different, so needs each i2c client on i2c
operation functions.
Also, this patch exports i2c operation functions instead of callback to
make easy to read.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In current implementation, vid is declared as u8,
then "vid == -1" is always false, and "vid >= 0" is always true.
Thus change it to s8.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Commit f03f91826 (regulator: Add option for machine drivers
to enable the dummy regulator) in the regulators tree
seems to have introduced the following build break when
CONFIG_REGULATOR_DUMMY is disabled. Fix this.
CC drivers/regulator/dummy.o
drivers/regulator/dummy.c:41: error: redefinition of 'regulator_dummy_init'
drivers/regulator/dummy.h:28: note: previous definition of 'regulator_dummy_init' was here
make[2]: *** [drivers/regulator/dummy.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
I have a regulator A that sets regulator B as its supply. When I call
set_supply to add B as the supply for A, regulator A gets added to the
supply_list for regulator B.
When I call regulator_disable(A), I end up with a call chain like this:
regulator_disable(A)
> mutex_lock(A)
> _regulator_disable(A)
>> _regulator_disable(B)
>>> _notifier_call_chain(B)
>>>> mutex_lock(A)
Which results in dead lock since we are trying to acquire the mutex lock
for regulator A which we already hold.
This patch addresses this issue by moving the call to disable regulator
B outside of the lock aquired inside the initial call to
regulator_disable.
This change also addresses the issue of not acquiring the mutex for
regulator B before calling _regulator_disable(B).
Signed-off-by: Jeffrey Carlyle <jeff.carlyle@motorola.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow machine drivers to explicitly enable the use of the dummy regulator,
enabling simpler support for systems with only a few specific supplies
visible to software.
It is strongly recommended that this is not used on systems with
substantial software control over their PMICs, for maximum functionality
constrints should be as fully specified as possible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch includes below fixes based on Mark's comment.
- Return actual error if i2c_smbus_read_byte_data() fail
- Add spaces around bitwise AND operator(&) to improve readability
- Add comment to explain why we need to update voltage change control register
for LDO1 and LDO5
- Logging the value for diagnostics if chip reported incorrect voltage value
- Add __devinit annotation for setup_regulators()
- Show system control register1 value if the value is mismatched
- Logging the value for diagnostics if failed to detect device
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds regulator drivers for National Semiconductors LP3972 PMIC.
This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out
(LDO) regulators. LP3972 PMIC controller uses I2C interface.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV
with DVS support. In this initial release, users can set voltages for
four DVS modes, RAMP delay values, and SYNC frequency.
Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID
is not supported in this release.
If GPIO of EN is not valid in platform data, the driver assumes that it
is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down
VID0 and VID1 to fix DVS mode as 0 and disables DVS support.
We assume that V_OUT is capable to provide every voltage from 770mV to
1.40V in 10mV steps although the data sheet has some ambiguity on it.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
v2:
- Style correction
- Can accept platform_data with invalid GPIOs
- Removed unnecessary features
- Improved error handling
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
of/i2c: Fix module load order issue caused by of_i2c.c
i2c: Fix checks which cause legacy suspend to never get called
i2c-pca: Fix waitforcompletion() return value
i2c: Fix for suspend/resume issue
i2c: Remove obsolete cleanup for clientdata
The SYNC bits are BIT6 and BIT7 of MAX8649_SYNC register.
pdata->extclk_freq could be [0|1|2].
(MAX8649_EXTCLK_26MHZ|MAX8649_EXTCLK_13MHZ|MAX8649_EXTCLK_19MHZ)
It requires to left shift 6 bits to properly set extclk_freq.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch fixes a typo that incorrectly reports mA numbers as uA.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If device_register() fails then call put_device().
See comment to device_register.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In wm8350_dcdc_set_mode(), we set DCx_SLEEP bit of WM8350_DCDC_SLEEP_OPTIONS
register for REGULATOR_MODE_STANDBY mode.
( DCx_SLEEP bits: 0: Normal DC-DC operation 1: Select LDO mode )
In wm8350_dcdc_get_mode(), current logic to determinate
REGULATOR_MODE_STANDBY mode is just reverse.
( sleep is set should mean REGULATOR_MODE_STANDBY mode. )
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Problem description in current implementation:
When setting REGULATOR_MODE_IDLE mode, current implementation set
WM831X_LDO1_LP_MODE bit of ctrl_reg (which is wrong, it should clear the bit).
But due to a missing break statement for case REGULATOR_MODE_IDLE, the code
fall through to case REGULATOR_MODE_STANDBY and then clear
WM831X_LDO1_LP_MODE bit. So it still looks OK when checking the status
by wm831x_gp_ldo_get_mode().
When setting REGULATOR_MODE_STANDBY mode, it just does not work.
wm831x_gp_ldo_get_mode() will still return REGULATOR_MODE_IDLE because
the accordingly WM831X_LDO1_LP_MODE bit is clear.
Correct behavior should be:
Clear WM831X_LDO1_LP_MODE bit of ctrl_reg for REGULATOR_MODE_IDLE mode.
Set WM831X_LDO1_LP_MODE bit of ctrl_reg for REGULATOR_MODE_STANDBY mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
selector is used as array index of info->supported_voltages
Thus the valid value range should be 0 .. info->voltages_len -1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@openource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In choose_voltage(), we use i as array index of info->vol_table.
The valid value range for i should be 0 .. ARRAY_SIZE(info->vol_table) - 1.
Take LDO1 as example, ARRAY_SIZE(LDO1_table) is 4, vol_nbits of LDO1 is 2.
for (i = 0; i < (2 << info->vol_nbits); i++) is equivalent to
for (i = 0; i < 8; i++)
which is wrong.
The same value range checking also applies for index in pm8607_list_voltage().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@openource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In current implementation, the address return from regulator_register()
is different from the address for regulator_unregister().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
max8998->dev is NULL in current implementation, set it to &pdev->dev.
regulator_register() still return success if max8998->dev is NULL,
but rdev->dev.parent will be set to NULL which is incorrect.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
