Commit Graph

53 Commits

Author SHA1 Message Date
Shubhrajyoti Datta
0077428118 gpio: zynq: Remove error prints in EPROBE_DEFER
In case of probe is deferred do not print the errors.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-06-24 12:17:12 +02:00
Shubhrajyoti Datta
73c612fe2a gpio: zynq: Add pmc gpio support
Add PMC gpio support.
Only bank 0,1, 3 and 4 are connected to the multiplexed Input output
pins. Bank 0 and 1 to mio and bank 3 and 4 to extended multiplexed input
output pins.

Versal devices are the industry's first adaptive compute
acceleration platforms.
https://www.xilinx.com/support/documentation/data_sheets/ds950-versal-overview.pdf

On the Versal platform, we are using two customized GPIO controllers(IP)
which were used in Zynq/ZynqMp platform.
One of them present in the Platform Management Controller(PMC) block and
other in Processing System(PS) block.

In PMC_GPIO only Bank0,1,3 & 4 are enabled and in PS_GPIO only
Bank 0 & 3 are enabled.

You can find more details of GPIO IP in ZynqMP TRM General Purpose
I/O(Chapter-27).
https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-06-24 12:16:57 +02:00
Shubhrajyoti Datta
26ebdbf8c2 gpio: zynq: Disable the irq if it is not a wakeup source
If gpio is not set to wake disable the interrupt. ATF set all slaves with
enabled interrupts as wakeup sources and if gpio is used in r5 then it
wakes up linux.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-06-24 12:16:39 +02:00
Shubhrajyoti Datta
675002448e gpio: zynq: Add Versal support
Add Versal support in gpio.
Only bank 0 and 3 are connected to the Multiplexed Input output pins.
Bank 0 to mio and bank3 to fabric Multiplexed input output pins.

Versal devices are the industry's first adaptive compute
acceleration platforms.
https://www.xilinx.com/support/documentation/data_sheets/ds950-versal-overview.pdf

On the Versal platform, we are using two customized GPIO controllers(IP)
which were used in Zynq/ZynqMp platform.
One of them present in the Platform Management Controller(PMC) block and
other in Processing System(PS) block.

In PMC_GPIO only Bank0,1,3 & 4 are enabled and in PS_GPIO only
Bank 0 & 3 are enabled.

You can find more details of GPIO IP in ZynqMP TRM General Purpose
I/O(Chapter-27).
https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-06-24 12:15:50 +02:00
Glenn Langedock
fdcfec11b2 gpio: zynq: protect direction in/out with a spinlock
Fix race condition when changing the direction (in/out) of the GPIO pin.
The read-modify-write sequence (as coded in the driver) isn't atomic and
requires synchronization (spinlock).

Signed-off-by: Glenn Langedock <Glenn.Langedock@barco.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2020-06-24 12:10:09 +02:00
Swapna Manupati
36f2e7207f gpio: zynq: Fix for bug in zynq_gpio_restore_context API
This patch writes the inverse value of Interrupt Mask Status
register into the Interrupt Enable register in
zynq_gpio_restore_context API to fix the bug.

Fixes: e11de4de28 ("gpio: zynq: Add support for suspend resume")
Signed-off-by: Swapna Manupati <swapna.manupati@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Link: https://lore.kernel.org/r/1577362338-28744-2-git-send-email-srinivas.neeli@xilinx.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-01-07 11:24:44 +01:00
Matti Vaittinen
e42615ec23 gpio: Use new GPIO_LINE_DIRECTION
It's hard for occasional GPIO code reader/writer to know if values 0/1
equal to IN or OUT. Use defined GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT to help them out.

NOTE - for gpio-amd-fch and gpio-bd9571mwv:
This commit also changes the return value for direction get to equal 1
for direction INPUT. Prior this commit these drivers might have
returned some other positive value but 1 for INPUT.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-11-07 09:27:48 +01:00
Linus Walleij
f6a7053ddc gpio: zynq: Pass irqchip when adding gpiochip
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.

For chained irqchips this is a pretty straight-forward
conversion.

Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190809132649.25176-1-linus.walleij@linaro.org
2019-08-27 13:07:36 +02:00
Stephen Boyd
15bddb7d78 gpio: Remove dev_err() usage after platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).

Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-16-swboyd@chromium.org
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-08-05 13:25:34 +02:00
Thomas Gleixner
2874c5fd28 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:32 -07:00
Enrico Weigelt, metux IT consult
77bc0e69c3 gpio: zynq: use devm_platform_ioremap_resource()
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.

Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-04-05 00:04:28 +07:00
Thomas Petazzoni
c2df3de0d0 gpio: zynq: properly support runtime PM for GPIO used as interrupts
The Zynq GPIO driver currently implements runtime PM by:

 - Enabling runtime PM support in ->probe() and letting the runtime PM
   reference counter drop to zero at the end of ->probe().

 - Increasing the runtime PM reference counter in ->request() and
   decreasing it in ->free().

However, the latter is not sufficient: when a GPIO is used as an
interrupt, ->request() and ->free() are not called. Due to this, the
runtime PM counter remains to zero when the only GPIOs in use are used
as interrupts, causing them to simply not work.

To address this problem, this commit implement the
->irq_request_resources() and ->irq_release_resources() hooks,
ensuring that the runtime PM counter is properly
incremented/decremented. Since we override the default hooks, we keep
the existing behavior by making sure they call gpiochip_reqres_irq() /
gpiochip_relres_irq() respectively.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-02-13 10:36:54 +01:00
Brandon Maier
6169005ceb gpio: zynq: Report gpio direction at boot
The Zynq's gpios can be configured by the bootloader. But Linux will
erroneously report all gpios as inputs unless we implement
get_direction().

Signed-off-by: Brandon Maier <Brandon.Maier@collins.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-12-07 13:37:25 +01:00
Wolfram Sang
38ccad0243 gpio: gpio-zynq: simplify getting .driver_data
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05 08:54:41 +01:00
Michal Simek
060f3ebf6a gpio: zynq: Setup chip->base based on alias ID
In past Xilinx gpio-zynq driver was setting up gpio chip->base as 0
which was chagned to autodetection when driver was upstreamed. Older
systems, which were using this old version, setup SW stack which expects
zynq gpio base as 0 and right now there is no way how to set this up.

The patch is adding an option to setup chip->base based on aliases which
is something what some other drivers are doing too.
It means when gpio0 alias is setup then chip->base is 0. When gpio alias
is not setup gpiochip_find_base() set it up properly which is current
behavior.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-23 11:43:03 +02:00
Shubhrajyoti Datta
a76e865eea gpio: zynq: simplifly getting drvdata
Get the driver data directly by dev_get_drvdata.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-23 09:57:08 +02:00
Shubhrajyoti Datta
5e3a8ecd76 gpio: zynq: Remove call to platform_get_irq
Remove the call to  platform_get_irq use the cached
one instead.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-23 09:55:53 +02:00
Thierry Reding
f0fbe7bce7 gpio: Move irqdomain into struct gpio_irq_chip
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-08 14:06:21 +01:00
Michal Simek
16ee62e560 gpio: zynq: Fix driver function parameters alignment
Fix function parameters alignment reported by checkpatch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14 16:01:06 +02:00
Nava kishore Manne
2717cfcaf5 gpio: zynq: Fix warnings in the driver
This patch fixes the below warning
	-->Block comments should align the * on each line.
	-->suspect code indent for conditional statements.
	-->Prefer 'unsigned int' to bare use of 'unsigned'

Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14 16:00:08 +02:00
Michal Simek
eb73d6eaa6 gpio: zynq: Fix empty lines in driver
Remove one additional line and add two new. All are reported by checkpatch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14 15:59:37 +02:00
Nava kishore Manne
6ae5104cba gpio: zynq: Fix kernel doc warnings
This patch fixes the kernel doc warnings in the driver.

Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14 15:58:22 +02:00
Swapna Manupati
06aa09081d gpio: zynq: Provided workaround for GPIO
This patch provides workaround in the gpio driver
for Zynq and ZynqMP Platforms by reading pin value
of EMIO banks through DATA register as it was unable
to read the value of it from DATA_RO register.

Signed-off-by: Swapna Manupati <swapnam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14 15:57:06 +02:00
Shubhrajyoti Datta
e11de4de28 gpio: zynq: Add support for suspend resume
Add support for suspend resume. Now that we can lose context across
a suspend/ resume cycle. Add support for the context restore.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14 15:43:53 +02:00
Soren Brinkmann
3638bd4a06 gpio: zynq: Clarify quirk and provide helper function
The one quirk used in the zynq GPIO driver was called FOO which is not
very descriptive. Rename the quirk to IS_ZYNQ as it indicates whether
the HW is a zynq or zynqmp device to allow handling of device-specific
differences of the HW.
Also provide a helper function to test whether the HW is zynq or zynqmp.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-16 11:13:12 +02:00
Masahiro Yamada
7808c42b40 gpio: zynq: remove unneeded (void *) casts in of_match_table
of_device_id::data is an opaque pointer.  No explicit cast is needed.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-22 17:13:04 +02:00
Nava kishore Manne
e3296f19c8 gpio: Added zynq specific check for special pins on bank zero
This patch adds zynq specific check for bank 0 pins 7 and 8
are special and cannot be used as inputs

Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Reported-by: Jonas Karlsson <Jonas.d.karlsson@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-23 15:26:20 +02:00
Helmut Grohne
0f84f29ff3 gpio: zynq: initialize clock even without CONFIG_PM
When the PM initialization was moved in the commit referenced below, the
code enabling the clock was removed from the probe function. On
CONFIG_PM=y kernels, this is not a problem as the pm resume hook enables
the clock, but when power management is disabled, all those pm_*
functions are noops and the clock is never enabled resulting in a
dysfunctional gpio controller.

Put the clock initialization back to support CONFIG_PM=n.

Cc: stable@vger.kernel.org
Signed-off-by: Helmut Grohne <h.grohne@intenta.de>
Fixes: 3773c195d3 ("gpio: zynq: Do PM initialization earlier to support gpio hogs")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-06-08 10:36:29 +02:00
Shubhrajyoti Datta
615d23f80e gpio: zynq: Fix the error path
pm_runtime_disable is called only in remove it is missed
out in the error path.
Fix the same.

Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-04-09 20:14:36 +02:00
Linus Walleij
31a8944752 gpio: zynq: use gpiochip data pointer
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-01-05 11:21:20 +01:00
Michal Simek
3773c195d3 gpio: zynq: Do PM initialization earlier to support gpio hogs
GPIO hogs registration is call at the end of gpiochip_add() function.
Calling sequence is:
gpiochip_add -> of_gpiochip_add -> of_gpiochip_scan_hogs ->
gpiod_hog -> gpiochip_request_own_desc -> __gpiod_request ->
chip->request -> zynq_gpio_request which calls pm_runtime_get_sync()
which returns -13 because PM is not initialized yet.

Initialize PM before gpiochip_add is called to fix this issue.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-14 14:10:04 +01:00
Linus Walleij
58383c7842 gpio: change member .dev to .parent
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.

This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:

@@
struct gpio_chip *var;
@@
-var->dev
+var->parent

and:

@@
struct gpio_chip var;
@@
-var.dev
+var.parent

and:

@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent

Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.

This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.

Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-19 09:24:35 +01:00
Linus Walleij
fa9795d112 gpio: zynq: use container_of() to get state container
The state container of the Zynq GPIO driver is sometimes
extracted from the gpio_chip exploiting the fact that offsetof()
the struct gpio_chip inside the struct zynq_gpio is 0, so
the container_of() is in practice a noop. However if a member
is added to struct zynq_gpio in front of struct gpio_chip,
things will break. Using proper container_of() avoids this
problem.

Semantically this is a noop, the compiler will optimize it away,
but syntactically it makes me happier.

Also replace some explicit container_of() calls with the helper
function.

Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ezra Savard <ezra.savard@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-02 04:19:33 -07:00
Thomas Gleixner
bd0b9ac405 genirq: Remove irq argument from irq flow handlers
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.

Remove the argument.

Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
2015-09-16 15:47:51 +02:00
Linus Walleij
5f6f02cd49 Linux 4.2-rc4
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJVtTRqAAoJEHm+PkMAQRiGN+wH/1mPJBCvt7DqvV90+/QKPEA6
 KXWtiy+oDavOv1vPcwL4gdYmMqXd2fSv82Zv5+E5ABFHXSyZvG5eCZvQLPz0V73f
 ldrSgTYVfbYb0W+TnaC1gr8aMS38i4F/eXCoPZMtO8WyUn7xhJZS9Y3U8Ff4/gp3
 to+4TaHhsnv2R79UyoR4elObo2n6aMkBSertjndbYoEQ4Zgr5iIoxbMDi4raeghP
 BLB6Mh50tqNMxE5OL/ERj1oHmJK9TIy2sNmOhP/1xp7XGK/KZm8Z+CIglaf1gOcM
 IM8pEgwDIlxp78MERn/PB/+xDkgUw0W9OqKPcUxiIt+M7TNRQ9UTb4Tn1SR2/cE=
 =fHSS
 -----END PGP SIGNATURE-----

Merge tag 'v4.2-rc4' into devel

Linux 4.2-rc4
2015-08-13 14:42:55 +02:00
Linus Walleij
bcae888039 Merge branch 'queue/irq/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into devel 2015-07-17 14:45:31 +02:00
Michal Simek
6b956af080 gpio: zynq: Fix problem with unbalanced pm_runtime_enable
Add missing pm_runtime_disabled to remove().

Error log:
root@zynqmp:~# modprobe gpio_zynq
root@zynqmp:~# lsmod
    Not tainted
gpio_zynq 7086 0 - Live 0xffffffbffc00a000
root@zynqmp:~# rmmod gpio_zynq
root@zynqmp:~# lsmod
    Not tainted
root@zynqmp:~# modprobe gpio_zynq
[  246.924438] zynq-gpio ff0a0000.gpio: Unbalanced pm_runtime_enable!
root@zynqmp:~# rmmod gpio_zynq
root@zynqmp:~# lsmod
    Not tainted

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-16 13:00:43 +02:00
Masahiro Yamada
80d2bf55a1 gpio: zynq: add missing module_exit function
This driver is tristate, so it should be cleanable.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-07-16 00:11:02 +02:00
Jiang Liu
476f8b4c94 gpio: Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.

Preparatory patch for the removal of the 'irq' argument from irq flow
handlers.

Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2015-07-14 12:12:20 +02:00
Thomas Gleixner
47c0846292 gpio/zynq: Use irq_set_chip_handler_name_locked()
Hand in irq_data and avoid the redundant lookup of irq_desc.

Originally-from: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2015-07-14 12:12:19 +02:00
Anurag Kumar Vulisha
bdf7a4ae37 gpio: Added support to Zynq Ultrascale+ MPSoC
Added support to Zynq Ultrascale+ MPSoC on the existing zynq
gpio driver.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-06-10 09:44:17 +02:00
Colin Cronin
20a8a96873 Drivers: gpio: Fix spelling errors
Fixed several spelling errors in gpio-lynxpoint, gpio-pca953x,
gpio-tegra, gpio-zynq, gpiolib-of, gpiolib.

Signed-off-by: Colin Cronin <colinpatrickcronin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-05-19 16:52:30 +02:00
Rafael J. Wysocki
6ed23b806e PM: Merge the SET*_RUNTIME_PM_OPS() macros
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.

However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.

For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.

Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-12-04 00:51:30 +01:00
Linus Walleij
da26d5d803 gpio: remove remaining users of gpiochip_remove() retval
Some drivers accidentally still use the return value from
gpiochip_remove(). Get rid of them so we can simplify this function
and get rid of the return value.

Cc: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-23 17:51:17 +02:00
abdoulaye berthe
88d5e520aa driver:gpio remove all usage of gpio_remove retval in driver
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.

Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-18 11:03:10 -07:00
Ezra Savard
59e22114b2 gpio: zynq: Fixed broken wakeup implementation
Use of unmask/mask in set_wake was an incorrect implementation. The new
implementation correctly sets wakeup for the gpio chip's IRQ so the gpio chip
will not sleep while wakeup-enabled gpio are in use.

Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-04 18:23:29 +02:00
Ezra Savard
a194677881 gpio: zynq: Mask non-wakeup GPIO interrupts on suspend
Added flag to the GPIO chip so that IRQ from non-wakeup GPIO will
not wake the system.

Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-04 18:22:17 +02:00
Lars-Peter Clausen
016da14439 gpio: zynq: Take bank offset into account when reporting a IRQ
When looking up the IRQ the bank offset needs to be taken into account.
Otherwise interrupts for banks other than bank 0 get incorrectly reported as
interrupts for bank 0.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-03 13:56:31 +02:00
Lars-Peter Clausen
5a2533a747 gpio: zynq: Reduce level of indention in zynq_gpio_irqhandler()
zynq_gpio_irqhandler() uses up to 7 tabs of indention in some parts. Refactor
things to use a helper function for the inner loop to reduce the indention to a
sane level.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-08-29 08:31:57 +02:00
Michal Simek
51dd2e8ec9 gpio: zynq: Remove .owner field for driver
There is no need to init .owner field.

Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"

This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-08-29 07:46:20 +02:00