The FXSAVE information leak patch introduced a bug in FP exception
handling: it clears FP exceptions only when there are already
none outstanding. Mikael Pettersson reported that causes problems
with the Erlang runtime and has tested this fix.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These aren't needed by glibc or klibc, and they're broken in some cases
anyway. The uClibc folks are apparently switching over to stop using
them too (now that we agreed that they should be dropped, at least).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Proposed fix for ptep_get_and_clear_full PAE bug. Pte_clear had the same bug,
so use the same fix for both. Turns out pmd_clear had it as well, but pgds
are not affected.
The problem is rather intricate. Page table entries in PAE mode are 64-bits
wide, but the only atomic 8-byte write operation available in 32-bit mode is
cmpxchg8b, which is expensive (at least on P4), and thus avoided. But it can
happen that the processor may prefetch entries into the TLB in the middle of an
operation which clears a page table entry. So one must always clear the P-bit
in the low word of the page table entry first when clearing it.
Since the sequence *ptep = __pte(0) leaves the order of the write dependent on
the compiler, it must be coded explicitly as a clear of the low word followed
by a clear of the high word. Further, there must be a write memory barrier
here to enforce proper ordering by the compiler (and, in the future, by the
processor as well).
On > 4GB memory machines, the implementation of pte_clear for PAE was clearly
deficient, as it could leave virtual mappings of physical memory above 4GB
aliased to memory below 4GB in the TLB. The implementation of
ptep_get_and_clear_full has a similar bug, although not nearly as likely to
occur, since the mappings being cleared are in the process of being destroyed,
and should never be dereferenced again.
But, as luck would have it, it is possible to trigger bugs even without ever
dereferencing these bogus TLB mappings, even if the clear is followed fairly
soon after with a TLB flush or invalidation. The problem is that memory above
4GB may now be aliased into the first 4GB of memory, and in fact, may hit a
region of memory with non-memory semantics. These regions include AGP and PCI
space. As such, these memory regions are not cached by the processor. This
introduces the bug.
The processor can speculate memory operations, including memory writes, as long
as they are committed with the proper ordering. Speculating a memory write to
a linear address that has a bogus TLB mapping is possible. Normally, the
speculation is harmless. But for cached memory, it does leave the falsely
speculated cacheline unmodified, but in a dirty state. This cache line will be
eventually written back. If this cacheline happens to intersect a region of
memory that is not protected by the cache coherency protocol, it can corrupt
data in I/O memory, which is generally a very bad thing to do, and can cause
total system failure or just plain undefined behavior.
These bugs are extremely unlikely, but the severity is of such magnitude, and
the fix so simple that I think fixing them immediately is justified. Also,
they are nearly impossible to debug.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_splice() moves data to/from pipes with a file input/output. sys_vmsplice()
moves data to a pipe, with the input being a user address range instead.
This uses an approach suggested by Linus, where we can hold partial ranges
inside the pages[] map. Hopefully this will be useful for network
receive support as well.
Signed-off-by: Jens Axboe <axboe@suse.de>
AMD K7/K8 CPUs only save/restore the FOP/FIP/FDP x87 registers in FXSAVE
when an exception is pending. This means the value leak through
context switches and allow processes to observe some x87 instruction
state of other processes.
This was actually documented by AMD, but nobody recognized it as
being different from Intel before.
The fix first adds an optimization: instead of unconditionally
calling FNCLEX after each FXSAVE test if ES is pending and skip
it when not needed. Then do a x87 load from a kernel variable to
clear FOP/FIP/FDP.
This means other processes always will only see a constant value
defined by the kernel in their FP state.
I took some pain to make sure to chose a variable that's already
in L1 during context switch to make the overhead of this low.
Also alternative() is used to patch away the new code on CPUs
who don't need it.
Patch for both i386/x86-64.
The problem was discovered originally by Jan Beulich. Richard
Brunner provided the basic code for the workarounds, with contribution
from Jan.
This is CVE-2006-1056
Cc: richard.brunner@amd.com
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
atomic_add_return() if CONFIG_M386 can accidentally enable local interrupts.
Signed-off-by: Lepton Wu <ytht.net@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Basically an in-kernel implementation of tee, which uses splice and the
pipe buffers as an intelligent way to pass data around by reference.
Where the user space tee consumes the input and produces a stdout and
file output, this syscall merely duplicates the data inside a pipe to
another pipe. No data is copied, the output just grabs a reference to the
input pipe data.
Signed-off-by: Jens Axboe <axboe@suse.de>
* 'splice' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] vfs: add splice_write and splice_read to documentation
[PATCH] Remove sys_ prefix of new syscalls from __NR_sys_*
[PATCH] splice: warning fix
[PATCH] another round of fs/pipe.c cleanups
[PATCH] splice: comment styles
[PATCH] splice: add Ingo as addition copyright holder
[PATCH] splice: unlikely() optimizations
[PATCH] splice: speedups and optimizations
[PATCH] pipe.c/fifo.c code cleanups
[PATCH] get rid of the PIPE_*() macros
[PATCH] splice: speedup __generic_file_splice_read
[PATCH] splice: add direct fd <-> fd splicing support
[PATCH] splice: add optional input and output offsets
[PATCH] introduce a "kernel-internal pipe object" abstraction
[PATCH] splice: be smarter about calling do_page_cache_readahead()
[PATCH] splice: optimize the splice buffer mapping
[PATCH] splice: cleanup __generic_file_splice_read()
[PATCH] splice: only call wake_up_interruptible() when we really have to
[PATCH] splice: potential !page dereference
[PATCH] splice: mark the io page as accessed
__NR_sys_kexec_load should be __NR_kexec_load. Mainly affects users of the
_syscallN() macros, and glibc is already checking for __NR_kexec_load.
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current implementations define NODES_SHIFT in include/asm-xxx/numnodes.h for
each arch. Its definition is sometimes configurable. Indeed, ia64 defines 5
NODES_SHIFT values in the current git tree. But it looks a bit messy.
SGI-SN2(ia64) system requires 1024 nodes, and the number of nodes already has
been changeable by config. Suitable node's number may be changed in the
future even if it is other architecture. So, I wrote configurable node's
number.
This patch set defines just default value for each arch which needs multi
nodes except ia64. But, it is easy to change to configurable if necessary.
On ia64 the number of nodes can be already configured in generic ia64 and SN2
config. But, NODES_SHIFT is defined for DIG64 and HP'S machine too. So, I
changed it so that all platforms can be configured via CONFIG_NODES_SHIFT. It
would be simpler.
See also: http://marc.theaimsgroup.com/?l=linux-kernel&m=114358010523896&w=2
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On i386, we don't use sys_ prefix for __NR_*. This patch removes it
[FWIW, _syscall*() macros will generate foo() instead of sys_foo().]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Jens Axboe <axboe@suse.de>
If the HPET timer is enabled, the clock can drift by ~3 seconds a day.
This is due to the HPET timer not being initialized with the correct
setting (still using PIT count).
If HZ changes, this drift can become even more pronounced.
HPET patch initializes tick_nsec with correct tick_nsec settings for
HPET timer.
Vojtech comments:
"It's not entirely correct (it assumes the HPET ticks totally
exactly), but it's significantly better than assuming the PIT error
there."
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD systems have a modern APIC that supports 8 bit IDs, but
don't have a XAPIC version number. Add a new "modern_apic"
subfunction that handles this correctly and use it (nearly)
everywhere where XAPIC is tested for.
I removed one wart: the code specified that external APICs
would use an 8bit APIC ID. But I checked a real 82093 data sheet
and it says clearly that they only use 4bit. So I removed
this special case since it would a bit awkward to implement now.
I removed the valid APIC tests in mptable parsing completely. On any modern
system they only check against the full field width (8bit) anyways
and are no-ops. This also fixes them doing the wrong thing
on >8 core Opterons.
This makes i386 boot again on 16 core Opterons.
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce a e820_all_mapped() function which checks if the entire range
<start,end> is mapped with type.
This is done by moving the local start variable to the end of each
known-good region; if at the end of the function the start address is
still before end, there must be a part that's not of the correct type;
otherwise it's a good region.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
local_t's were defined to be unsigned. This increases confusion because
atomic_t's are signed. The patch goes through and changes all implementations
to use signed longs throughout.
Also, x86-64 was using 32-bit quantities for the value passed into local_add()
and local_sub(). Fixed.
All (actually, both) existing users have been audited.
(Also s/__inline__/inline/ in x86_64/local.h)
Cc: Andi Kleen <ak@muc.de>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the recently-added LINUX_FADV_ASYNC_WRITE and LINUX_FADV_WRITE_WAIT
fadvise() additions, do it in a new sys_sync_file_range() syscall instead.
Reasons:
- It's more flexible. Things which would require two or three syscalls with
fadvise() can be done in a single syscall.
- Using fadvise() in this manner is something not covered by POSIX.
The patch wires up the syscall for x86.
The sycall is implemented in the new fs/sync.c. The intention is that we can
move sys_fsync(), sys_fdatasync() and perhaps sys_sync() into there later.
Documentation for the syscall is in fs/sync.c.
A test app (sync_file_range.c) is in
http://www.zip.com.au/~akpm/linux/patches/stuff/ext3-tools.tar.gz.
The available-to-GPL-modules do_sync_file_range() is for knfsd: "A COMMIT can
say NFS_DATA_SYNC or NFS_FILE_SYNC. I can skip the ->fsync call for
NFS_DATA_SYNC which is hopefully the more common."
Note: the `async' writeout mode SYNC_FILE_RANGE_WRITE will turn synchronous if
the queue is congested. This is trivial to fix: add a new flag bit, set
wbc->nonblocking. But I'm not sure that we want to expose implementation
details down to that level.
Note: it's notable that we can sync an fd which wasn't opened for writing.
Same with fsync() and fdatasync()).
Note: the code takes some care to handle attempts to sync file contents
outside the 16TB offset on 32-bit machines. It makes such attempts appear to
succeed, for best 32-bit/64-bit compatibility. Perhaps it should make such
requests fail...
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Porting the patch I posted for x86_64 to i386.
http://marc.theaimsgroup.com/?l=linux-kernel&m=114178139610707&w=2
o While using kdump, after a system crash when second kernel boots, timer
vector gets (0x31) locked and CPU does not see timer interrupts
travelling from IOAPIC to APIC. Currently it does not lead to boot
failure in second kernel as timer interrupts continues to come as ExtInt
through LAPIC directly, but fixing it is good in case some boards do not
support the other mode.
o After a system crash, it is not safe to service interrupts any more,
hence interrupts are disabled. This leads to pending interrupts at
LAPIC. LAPIC sends these interrupts to the CPU during early boot of
second kernel. Other pending interrupts are discarded saying unexpected
trap but timer interrupt is serviced and CPU does not issue an LAPIC EOI
because it think this interrupt came from i8259 and sends ack to 8259.
This leads to vector 0x31 locking as LAPIC does not clear respective ISR
and keeps on waiting for EOI.
o This patch issues extra EOI for the pending interrupts who have ISR set.
o Though today only timer seems to be the special case because in early
boot it thinks interrupts are coming from i8259 and uses
mask_and_ack_8259A() as ack handler and does not issue LAPIC EOI. But
probably doing it in generic manner for all vectors makes sense.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's been disabled since v2.1.88
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds support for the sys_splice system call. Using a pipe as a
transport, it can connect to files or sockets (latter as output only).
From the splice.c comments:
"splice": joining two ropes together by interweaving their strands.
This is the "extended pipe" functionality, where a pipe is used as
an arbitrary in-memory buffer. Think of a pipe as a small kernel
buffer that you can use to transfer data from one end to the other.
The traditional unix read/write is extended with a "splice()" operation
that transfers data buffers to or from a pipe buffer.
Named by Larry McVoy, original implementation from Linus, extended by
Jens to support splicing to files and fixing the initial implementation
bugs.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nowadays, even Debian stable ships a microcode_ctl utility recent enough to no
longer use this ioctl.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Tigran Aivazian <tigran_aivazian@symantec.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up some RTC whitespace and style
Signed-off-by: Matt Mackall <mpm@selenic.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reading the CMOS clock on x86 and some other arches currently takes up to one
second because it synchronizes with the CMOS second tick-over. This delay
shows up at boot time as well a resume time.
This is the currently the most substantial boot time delay for machines that
are working towards instant-on capability. Also, a quick back of the envelope
calculation (.5sec * 2M users * 1 boot a day * 10 years) suggests it has cost
Linux users in the neighborhood of a million man-hours.
An earlier thread on this topic is here:
http://groups.google.com/group/linux.kernel/browse_frm/thread/8a24255215ff6151/2aa97e66a977653d?hl=en&lr=&ie=UTF-8&rnum=1&prev=/groups%3Fhl%3Den%26lr%3D%26ie%3DUTF-8%26selm%3D1To2R-2S7-11%40gated-at.bofh.it#2aa97e66a977653d
..from which the consensus seems to be that it's no longer desirable.
In my view, there are basically four cases to consider:
1) networked, need precise walltime: use NTP
2) networked, don't need precise walltime: use NTP anyway
3) not networked, don't need sub-second precision walltime: don't care
4) not networked, need sub-second precision walltime:
get a network or a radio time source because RTC isn't good enough anyway
So this patch series simply removes the synchronization in favor of a simple
seqlock-like approach using the seconds value.
Note that for purposes of timer accuracy on wakeup, this patch will cause us
to fire timers up to one second late. But as the current timer resume code
will already sync once (or more!), it's no worse for short timers.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix: initialize the robust list(s) to NULL in copy_process.
- doc update
- cleanup: rename _inuser to _inatomic
- __user cleanups and other small cleanups
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386: add the futex_atomic_cmpxchg_inuser() assembly implementation, and wire
up the new syscalls.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patchset provides a new (written from scratch) implementation of robust
futexes, called "lightweight robust futexes". We believe this new
implementation is faster and simpler than the vma-based robust futex solutions
presented before, and we'd like this patchset to be adopted in the upstream
kernel. This is version 1 of the patchset.
Background
----------
What are robust futexes? To answer that, we first need to understand what
futexes are: normal futexes are special types of locks that in the
noncontended case can be acquired/released from userspace without having to
enter the kernel.
A futex is in essence a user-space address, e.g. a 32-bit lock variable
field. If userspace notices contention (the lock is already owned and someone
else wants to grab it too) then the lock is marked with a value that says
"there's a waiter pending", and the sys_futex(FUTEX_WAIT) syscall is used to
wait for the other guy to release it. The kernel creates a 'futex queue'
internally, so that it can later on match up the waiter with the waker -
without them having to know about each other. When the owner thread releases
the futex, it notices (via the variable value) that there were waiter(s)
pending, and does the sys_futex(FUTEX_WAKE) syscall to wake them up. Once all
waiters have taken and released the lock, the futex is again back to
'uncontended' state, and there's no in-kernel state associated with it. The
kernel completely forgets that there ever was a futex at that address. This
method makes futexes very lightweight and scalable.
"Robustness" is about dealing with crashes while holding a lock: if a process
exits prematurely while holding a pthread_mutex_t lock that is also shared
with some other process (e.g. yum segfaults while holding a pthread_mutex_t,
or yum is kill -9-ed), then waiters for that lock need to be notified that the
last owner of the lock exited in some irregular way.
To solve such types of problems, "robust mutex" userspace APIs were created:
pthread_mutex_lock() returns an error value if the owner exits prematurely -
and the new owner can decide whether the data protected by the lock can be
recovered safely.
There is a big conceptual problem with futex based mutexes though: it is the
kernel that destroys the owner task (e.g. due to a SEGFAULT), but the kernel
cannot help with the cleanup: if there is no 'futex queue' (and in most cases
there is none, futexes being fast lightweight locks) then the kernel has no
information to clean up after the held lock! Userspace has no chance to clean
up after the lock either - userspace is the one that crashes, so it has no
opportunity to clean up. Catch-22.
In practice, when e.g. yum is kill -9-ed (or segfaults), a system reboot is
needed to release that futex based lock. This is one of the leading
bugreports against yum.
To solve this problem, 'Robust Futex' patches were created and presented on
lkml: the one written by Todd Kneisel and David Singleton is the most advanced
at the moment. These patches all tried to extend the futex abstraction by
registering futex-based locks in the kernel - and thus give the kernel a
chance to clean up.
E.g. in David Singleton's robust-futex-6.patch, there are 3 new syscall
variants to sys_futex(): FUTEX_REGISTER, FUTEX_DEREGISTER and FUTEX_RECOVER.
The kernel attaches such robust futexes to vmas (via
vma->vm_file->f_mapping->robust_head), and at do_exit() time, all vmas are
searched to see whether they have a robust_head set.
Lots of work went into the vma-based robust-futex patch, and recently it has
improved significantly, but unfortunately it still has two fundamental
problems left:
- they have quite complex locking and race scenarios. The vma-based
patches had been pending for years, but they are still not completely
reliable.
- they have to scan _every_ vma at sys_exit() time, per thread!
The second disadvantage is a real killer: pthread_exit() takes around 1
microsecond on Linux, but with thousands (or tens of thousands) of vmas every
pthread_exit() takes a millisecond or more, also totally destroying the CPU's
L1 and L2 caches!
This is very much noticeable even for normal process sys_exit_group() calls:
the kernel has to do the vma scanning unconditionally! (this is because the
kernel has no knowledge about how many robust futexes there are to be cleaned
up, because a robust futex might have been registered in another task, and the
futex variable might have been simply mmap()-ed into this process's address
space).
This huge overhead forced the creation of CONFIG_FUTEX_ROBUST, but worse than
that: the overhead makes robust futexes impractical for any type of generic
Linux distribution.
So it became clear to us, something had to be done. Last week, when Thomas
Gleixner tried to fix up the vma-based robust futex patch in the -rt tree, he
found a handful of new races and we were talking about it and were analyzing
the situation. At that point a fundamentally different solution occured to
me. This patchset (written in the past couple of days) implements that new
solution. Be warned though - the patchset does things we normally dont do in
Linux, so some might find the approach disturbing. Parental advice
recommended ;-)
New approach to robust futexes
------------------------------
At the heart of this new approach there is a per-thread private list of robust
locks that userspace is holding (maintained by glibc) - which userspace list
is registered with the kernel via a new syscall [this registration happens at
most once per thread lifetime]. At do_exit() time, the kernel checks this
user-space list: are there any robust futex locks to be cleaned up?
In the common case, at do_exit() time, there is no list registered, so the
cost of robust futexes is just a simple current->robust_list != NULL
comparison. If the thread has registered a list, then normally the list is
empty. If the thread/process crashed or terminated in some incorrect way then
the list might be non-empty: in this case the kernel carefully walks the list
[not trusting it], and marks all locks that are owned by this thread with the
FUTEX_OWNER_DEAD bit, and wakes up one waiter (if any).
The list is guaranteed to be private and per-thread, so it's lockless. There
is one race possible though: since adding to and removing from the list is
done after the futex is acquired by glibc, there is a few instructions window
for the thread (or process) to die there, leaving the futex hung. To protect
against this possibility, userspace (glibc) also maintains a simple per-thread
'list_op_pending' field, to allow the kernel to clean up if the thread dies
after acquiring the lock, but just before it could have added itself to the
list. Glibc sets this list_op_pending field before it tries to acquire the
futex, and clears it after the list-add (or list-remove) has finished.
That's all that is needed - all the rest of robust-futex cleanup is done in
userspace [just like with the previous patches].
Ulrich Drepper has implemented the necessary glibc support for this new
mechanism, which fully enables robust mutexes. (Ulrich plans to commit these
changes to glibc-HEAD later today.)
Key differences of this userspace-list based approach, compared to the vma
based method:
- it's much, much faster: at thread exit time, there's no need to loop
over every vma (!), which the VM-based method has to do. Only a very
simple 'is the list empty' op is done.
- no VM changes are needed - 'struct address_space' is left alone.
- no registration of individual locks is needed: robust mutexes dont need
any extra per-lock syscalls. Robust mutexes thus become a very lightweight
primitive - so they dont force the application designer to do a hard choice
between performance and robustness - robust mutexes are just as fast.
- no per-lock kernel allocation happens.
- no resource limits are needed.
- no kernel-space recovery call (FUTEX_RECOVER) is needed.
- the implementation and the locking is "obvious", and there are no
interactions with the VM.
Performance
-----------
I have benchmarked the time needed for the kernel to process a list of 1
million (!) held locks, using the new method [on a 2GHz CPU]:
- with FUTEX_WAIT set [contended mutex]: 130 msecs
- without FUTEX_WAIT set [uncontended mutex]: 30 msecs
I have also measured an approach where glibc does the lock notification [which
it currently does for !pshared robust mutexes], and that took 256 msecs -
clearly slower, due to the 1 million FUTEX_WAKE syscalls userspace had to do.
(1 million held locks are unheard of - we expect at most a handful of locks to
be held at a time. Nevertheless it's nice to know that this approach scales
nicely.)
Implementation details
----------------------
The patch adds two new syscalls: one to register the userspace list, and one
to query the registered list pointer:
asmlinkage long
sys_set_robust_list(struct robust_list_head __user *head,
size_t len);
asmlinkage long
sys_get_robust_list(int pid, struct robust_list_head __user **head_ptr,
size_t __user *len_ptr);
List registration is very fast: the pointer is simply stored in
current->robust_list. [Note that in the future, if robust futexes become
widespread, we could extend sys_clone() to register a robust-list head for new
threads, without the need of another syscall.]
So there is virtually zero overhead for tasks not using robust futexes, and
even for robust futex users, there is only one extra syscall per thread
lifetime, and the cleanup operation, if it happens, is fast and
straightforward. The kernel doesnt have any internal distinction between
robust and normal futexes.
If a futex is found to be held at exit time, the kernel sets the highest bit
of the futex word:
#define FUTEX_OWNER_DIED 0x40000000
and wakes up the next futex waiter (if any). User-space does the rest of
the cleanup.
Otherwise, robust futexes are acquired by glibc by putting the TID into the
futex field atomically. Waiters set the FUTEX_WAITERS bit:
#define FUTEX_WAITERS 0x80000000
and the remaining bits are for the TID.
Testing, architecture support
-----------------------------
I've tested the new syscalls on x86 and x86_64, and have made sure the parsing
of the userspace list is robust [ ;-) ] even if the list is deliberately
corrupted.
i386 and x86_64 syscalls are wired up at the moment, and Ulrich has tested the
new glibc code (on x86_64 and i386), and it works for his robust-mutex
testcases.
All other architectures should build just fine too - but they wont have the
new syscalls yet.
Architectures need to implement the new futex_atomic_cmpxchg_inuser() inline
function before writing up the syscalls (that function returns -ENOSYS right
now).
This patch:
Add placeholder futex_atomic_cmpxchg_inuser() implementations to every
architecture that supports futexes. It returns -ENOSYS.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Just about every architecture defines some macros to do operations on pfns.
They're all virtually identical. This patch consolidates all of them.
One minor glitch is that at least i386 uses them in a very skeletal header
file. To keep away from #include dependency hell, I stuck the new
definitions in a new, isolated header.
Of all of the implementations, sh64 is the only one that varied by a bit.
It used some masks to ensure that any sign-extension got ripped away before
the arithmetic is done. This has been posted to that sh64 maintainers and
the development list.
Compiles on x86, x86_64, ia64 and ppc64.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new sched domain for representing multi-core with shared caches
between cores. Consider a dual package system, each package containing two
cores and with last level cache shared between cores with in a package. If
there are two runnable processes, with this appended patch those two
processes will be scheduled on different packages.
On such systems, with this patch we have observed 8% perf improvement with
specJBB(2 warehouse) benchmark and 35% improvement with CFP2000 rate(with 2
users).
This new domain will come into play only on multi-core systems with shared
caches. On other systems, this sched domain will be removed by domain
degeneration code. This new domain can be also used for implementing power
savings policy (see OLS 2005 CMP kernel scheduler paper for more details..
I will post another patch for power savings policy soon)
Most of the arch/* file changes are for cpu_coregroup_map() implementation.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current kprobe copies the original instruction at the probe point and replaces
it with a breakpoint instruction (int3). When the kernel hits the probe
point, kprobe handler is invoked. And the copied instruction is single-step
executed on the copied buffer (not on the original address) by kprobe. After
that, the kprobe checks registers and modify it (if need) as if the
instructions was executed on the original address.
My proposal is based on the fact there are many instructions which do NOT
require the register modification after the single-step execution. When the
copied instruction is a kind of them, kprobe just jumps back to the next
instruction after single-step execution. If so, why don't we execute those
instructions directly?
With kprobe-booster patch, kprobes will execute a copied instruction directly
and (if need) jump back to original code. This direct execution is executed
when the kprobe don't have both post_handler and break_handler, and the copied
instruction can be executed directly.
I sorted instructions which can be executed directly or not;
- Call instructions are NG(can not be executed directly).
We should correct the return address pushed into top of stack.
- Indirect instructions except for absolute indirect-jumps
are NG. Those instructions changes EIP randomly. We should
check EIP and correct it.
- Instructions that change EIP beyond the range of the
instruction buffer are NG.
- Instructions that change EIP to tail 5 bytes of the
instruction buffer (it is the size of a jump instruction).
We must write a jump instruction which backs to original
kernel code in the instruction buffer.
- Break point instruction is NG. We should not touch EIP and
pass to other handlers.
- Absolute direct/indirect jumps are OK.- Conditional Jumps are NG.
- Halt and software-interruptions are NG. Because it will stay on
the instruction buffer of kprobes.
- Prefixes are NG.
- Unknown/reserved opcode is NG.
- Other 1 byte instructions are OK. But those instructions need a
jump back code.
- 2 bytes instructions are mapped sparsely. So, in this release,
this patch don't boost those instructions.
>From Intel's IA-32 opcode map described in IA-32 Intel Architecture Software
Developer's Manual Vol.2 B, I determined that following opcodes are not
boostable.
- 0FH (2byte escape)
- 70H - 7FH (Jump on condition)
- 9AH (Call) and 9CH (Pushf)
- C0H-C1H (Grp 2: includes reserved opcode)
- C6H-C7H (Grp11: includes reserved opcode)
- CCH-CEH (Software-interrupt)
- D0H-D3H (Grp2: includes reserved opcode)
- D6H (Reserved)
- D8H-DFH (Coprocessor)
- E0H-E3H (loop/conditional jump)
- E8H (Call)
- F0H-F3H (Prefixes and reserved)
- F4H (Halt)
- F6H-F7H (Grp3: includes reserved opcode)
- FEH-FFH(Grp4,5: includes reserved opcode)
Kprobe-booster checks whether target instruction can be boosted (can be
executed directly) at arch_copy_kprobe() function. If the target instruction
can be boosted, it clears "boostable" flag. If not, it sets "boostable" flag
-1. This is disabled status. In resume_execution() function, If "boostable"
flag is cleared, kprobe-booster measures the size of the target instruction
and sets "boostable" flag 1.
In kprobe_handler(), kprobe checks the "boostable" flag. If the flag is 1, it
resets current kprobe and executes instruction buffer directly instead of
single stepping.
When unregistering a boosted kprobe, it calls synchronize_sched()
after "int3" is removed. So we can ensure followings after
the synchronize_sched() called.
- interrupt handlers are finished on all CPUs.
- instruction buffer is not executed on all CPUs.
And we can release the boosted kprobe safely.
And also, on preemptible kernel, the booster is not enabled where the kernel
preemption is enabled. So, there are no preempted threads on the instruction
buffer.
The description of kretprobe-booster:
====================================
In the normal operation, kretprobe make a target function return to trampoline
code. And a kprobe (called trampoline_probe) have been inserted at the
trampoline code. When the kernel hits this kprobe, it calls kretprobe's
handler and it returns to original return address.
Kretprobe-booster patch removes the trampoline_probe. It allows the
trampoline code to call kretprobe's handler directly instead of invoking
kprobe. And tranpoline code returns to original return address.
This new trampoline code stores and restores registers, so the kretprobe
handler is still able to access those registers.
Current kprobe has about 1.3 usec/probe(*) overhead, and kprobe-booster patch
reduces it to 0.6 usec/probe(*). Also current kretprobe has about 2.0
usec/probe(*) overhead. Kprobe-booster patch reduces it to 1.3 usec/probe(*),
and the combination of both kprobe-booster patch and kretprobe-booster patch
reduces it to 0.9 usec/probe(*).
I expect the combination of both patches can reduce half of a probing
overhead.
Performance numbers strongly depend on the processor model.
Andrew Morton wrote:
> These preempt tricks look rather nasty. Can you please describe what the
> problem is, precisely? And how this code avoids it? Perhaps we can find
> something cleaner.
The problem is how to remove the copied instructions of the
kprobe *safely* on the preemptable kernel (CONFIG_PREEMPT=y).
Kprobes basically executes the following actions;
(1)int3
(2)preempt_disable()
(3)kprobe_prehandler()
(4)copied instructioin(single step)
(5)kprobe_posthandler()
(6)preempt_enable()
(7)return to the original code
During the execution of copied instruction, preemption is
disabled (from step (2) to (6)).
When unregistering the probes, Kprobe waits for RCU
quiescent state by using synchronize_sched() after removing
int3 instruction.
Thus we can ensure the copied instruction is not executed.
On the other hand, kprobe-booster executes the following actions;
(1)int3
(2)preempt_disable()
(3)kprobe_prehandler()
(4)preempt_enable() <-- this one is added by my patch
(5)copied instruction(direct execution)
(6)jmp back to the original code
The problem is that we have no way to prevent preemption on
step (5) or (6). We cannot call preempt_disable() after step (6),
because there are no rooms to do that. Thus, some other
processes may be preempted at step(5) or (6) on preemptable kernel.
And I couldn't find the easy way to ensure that other processes'
stack do *not* have the address of them. (I thought some way
to do that, but those are very costly.)
So currently, I simply boost the kprobe only when the probe
point is already preemption disabled.
> Also, the patch adds a preempt_enable() but I don't see a corresponding
> preempt_disable(). Am I missing something?
It is corresponding to the preempt_disable() in the top of
kprobe_handler().
I copied the code of kprobe_handler() here:
static int __kprobes kprobe_handler(struct pt_regs *regs)
{
struct kprobe *p;
int ret = 0;
kprobe_opcode_t *addr = NULL;
unsigned long *lp;
struct kprobe_ctlblk *kcb;
/*
* We don't want to be preempted for the entire
* duration of kprobe processing
*/
preempt_disable(); <-- HERE
kcb = get_kprobe_ctlblk();
Signed-off-by: Masami Hiramatsu <hiramatu@sdl.hitachi.co.jp>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add blkcnt_t as the type of inode.i_blocks. This enables you to make the size
of blkcnt_t either 4 bytes or 8 bytes on 32 bits architecture with CONFIG_LSF.
- CONFIG_LSF
Add new configuration parameter.
- blkcnt_t
On h8300, i386, mips, powerpc, s390 and sh that define sector_t,
blkcnt_t is defined as u64 if CONFIG_LSF is enabled; otherwise it is
defined as unsigned long.
On other architectures, it is defined as unsigned long.
- inode.i_blocks
Change the type from sector_t to blkcnt_t.
Signed-off-by: Takashi Sato <sho@tnes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch series fixes the following problems on 32 bits architecture.
o stat64 returns the lower 32 bits of blocks, although userland st_blocks
has 64 bits, because i_blocks has only 32 bits. The ioctl with FIOQSIZE has
the same problem.
o As Dave Kleikamp said, making >2TB file on JFS results in writing an
invalid block number to disk inode. The cause is the same as above too.
o In generic quota code dquot_transfer(), the file usage is calculated from
i_blocks via inode_get_bytes(). If the file is over 2TB, the change of
usage is less than expected. The cause is the same as above too.
o As Trond Myklebust said, statfs64's entries related to blocks are invalid
on statfs64 for a network filesystem which has more than 2^32-1 blocks with
CONFIG_LBD disabled. [PATCH 3/3]
We made patches to fix problems that occur when handling a large filesystem
and a large file. It was discussed on the mails titled "stat64 for over 2TB
file returned invalid st_blocks".
Signed-off-by: Takashi Sato <sho@tnes.nec.co.jp>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are more and more cases where we need to know DMI information
early to work around bugs. i386 already had early DMI scanning, but
x86-64 didn't. Implement this now.
This required some cleanup in the i386 code.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the half-closed devices notifiation, by adding a new POLLRDHUP
(and its alias EPOLLRDHUP) bit to the existing poll/select sets. Since the
existing POLLHUP handling, that does not report correctly half-closed
devices, was feared to be changed, this implementation leaves the current
POLLHUP reporting unchanged and simply add a new bit that is set in the few
places where it makes sense. The same thing was discussed and conceptually
agreed quite some time ago:
http://lkml.org/lkml/2003/7/12/116
Since this new event bit is added to the existing Linux poll infrastruture,
even the existing poll/select system calls will be able to use it. As far
as the existing POLLHUP handling, the patch leaves it as is. The
pollrdhup-2.6.16.rc5-0.10.diff defines the POLLRDHUP for all the existing
archs and sets the bit in the six relevant files. The other attached diff
is the simple change required to sys/epoll.h to add the EPOLLRDHUP
definition.
There is "a stupid program" to test POLLRDHUP delivery here:
http://www.xmailserver.org/pollrdhup-test.c
It tests poll(2), but since the delivery is same epoll(2) will work equally.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
include/linux/platform.h contained nothing that was actually used except
the default_idle() prototype, and is therefore removed by this patch.
This patch does the following with the platform specific default_idle()
functions on different architectures:
- remove the unused function:
- parisc
- sparc64
- make the needlessly global function static:
- arm
- h8300
- m68k
- m68knommu
- s390
- v850
- x86_64
- add a prototype in asm/system.h:
- cris
- i386
- ia64
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Patrick Mochel <mochel@digitalimplant.org>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
unused isa_...() helpers removed.
Adrian Bunk:
The asm-sh part was rediffed due to unrelated changes.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without branch hints, the very unlikely chance of the loop repeating due to
cmpxchg failure is unrolled with gcc-4 that I have tested.
Improve this for architectures with a native cas/cmpxchg. llsc archs
should try to implement this natively.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Seems like needless clutter having a bunch of #if defined(CONFIG_$ARCH) in
include/linux/cache.h. Move the per architecture section definition to
asm/cache.h, and keep the if-not-defined dummy case in linux/cache.h to
catch architectures which don't implement the section.
Verified that symbols still go in .data.read_mostly on parisc,
and the compile doesn't break.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Gcc reserves %ebx when compiling position-independent-code on i386. This
means, the _syscallX() macros in include/asm-i386/unistd.h will not
compile. This patch is changes the existing macros to take special care to
preserve %ebx.
The bug can be tracked at http://bugzilla.kernel.org/show_bug.cgi?id=6204
Signed-off-by: Markus Gutschke <markus@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
_raw_spin_lock_flags() is entered with interrupts disabled. If it cannot
obtain a spinlock, it checks the flags that were passed and re-enables
interrupts before spinning if that's how the flags are set. When the
spinlock might be available, it disables interrupts (even if they are
already disabled) before trying to get the lock. Change that so interrupts
are only disabled if they have been enabled. This costs nine bytes of
duplicated spinloop code.
Fastpath before patch:
jle <keep looping> not-taken conditional jump
cli disable interrupts
jmp <try for lock> unconditional jump
Fastpath after patch, if interrupts were not enabled:
jg <try for lock> taken conditional branch
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/i386/kernel/cpu/centaur.c: In function `centaur_mcr_insert':
arch/i386/kernel/cpu/centaur.c:33: warning: implicit declaration of function `mtrr_centaur_report_mcr'
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
>commit 76381fee7e
>Author: Vincent Hanquez <vincent.hanquez@cl.cam.ac.uk>
>Date: Thu Jun 23 00:08:46 2005 -0700
>
> [PATCH] xen: x86_64: use more usermode macro
>
> Make use of the user_mode macro where it's possible. This is useful for Xen
> because it will need only to redefine only the macro to a hypervisor call.
I am of the opinion that the above changeset is incomplete, i.e. it missed
converting some previous uses of user_mode to user_mode_vm. While most of
them could be considered just cosmetical, at least the one in die_nmi
doesn't appear to be.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Vincent Hanquez <vincent.hanquez@cl.cam.ac.uk>
Cc: Zachary Amsden <zach@vmware.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Registering a callback handler through register_die_notifier() is obviously
primarily intended for use by modules. However, the way these currently
get called it is basically impossible for them to actually be used by
modules, as there is, on non-PAE configurationes, a good chance (the larger
the module, the better) for the system to crash as a result.
This is because the callback gets invoked
(a) in the page fault path before the top level page table propagation
gets carried out (hence a fault to propagate the top level page table
entry/entries mapping to module's code/data would nest infinitly) and
(b) in the NMI path, where nested faults must absolutely not happen,
since otherwise the IRET from the nested fault re-enables NMIs,
potentially resulting in nested NMI occurences.
Besides the modular aspect, similar problems would even arise for in-
kernel consumers of the API if they touched ioremap()ed or vmalloc()ed
memory inside their handlers.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The history is that -mm kernels do not work for me for a few months
already. The things started from crashing somewhere after starting init,
and for the last month - no boot at all, just "Uncompressing... OK,
booting kernel", and silence. Early console didn't work too. With the
latest releases this degraded into an infinite stream of the "Unknown
interrupt or fault" messages. So today my patience ran out and I started
to think how can I collect at least some info for the bug-report. Attached
is the patch that allows to gather some valueable debug info on the problem
by making an early console more useable. I can't properly test the patch,
as the kernel still doesn't boot, so I'll explain it in details in a hope
someone else can justify the intrusive changes.
arch_hooks.h: added prototypes for setup_early_printk() and early_printk().
setup.c: killed wrong setup_early_printk() prototype. Moved
setup_early_printk() a bit earlier, as it was not "early enough" to cover
the bug I was fighting with.
early_printk.c: made it to start printing from the bottom of the screen,
otherwise the messages interfere with the ones of the boot-loader, so you
can't read them.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Cc: Andi Kleen <ak@muc.de>
Cc: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ES7000 platform code clean up for compilation errors and a warning.
Ifdef'd the ACPI related parts in the ES7000 platform code. They were
causing compile errors in certain configuration (without ACPI defined). I
think this approach would be best (as opposed to Kconfig changes) since it
only touches the subarch...
Signed-off-by: <Natalie.Protasevich@unisys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In some code I am developing I had occasion to change the type of a
variable. This made the value put_user was putting to user space wrong.
But the code continued to build cleanly without errors.
Introducing a temporary fixes this problem and at least with gcc-3.3.5 does
not cause gcc any problems with optimizing out the temporary. gcc-4.x
using SSA internally ought to be even better at optimizing out temporaries,
so I don't expect a temporary to become a problem. Especially because in
all correct cases the types on both sides of the assignment to the
temporary are the same.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement SMP alternatives, i.e. switching at runtime between different
code versions for UP and SMP. The code can patch both SMP->UP and UP->SMP.
The UP->SMP case is useful for CPU hotplug.
With CONFIG_CPU_HOTPLUG enabled the code switches to UP at boot time and
when the number of CPUs goes down to 1, and switches to SMP when the number
of CPUs goes up to 2.
Without CONFIG_CPU_HOTPLUG or on non-SMP-capable systems the code is
patched once at boot time (if needed) and the tables are released
afterwards.
The changes in detail:
* The current alternatives bits are moved to a separate file,
the SMP alternatives code is added there.
* The patch adds some new elf sections to the kernel:
.smp_altinstructions
like .altinstructions, also contains a list
of alt_instr structs.
.smp_altinstr_replacement
like .altinstr_replacement, but also has some space to
save original instruction before replaving it.
.smp_locks
list of pointers to lock prefixes which can be nop'ed
out on UP.
The first two are used to replace more complex instruction
sequences such as spinlocks and semaphores. It would be possible
to deal with the lock prefixes with that as well, but by handling
them as special case the table sizes become much smaller.
* The sections are page-aligned and padded up to page size, so they
can be free if they are not needed.
* Splitted the code to release init pages to a separate function and
use it to release the elf sections if they are unused.
Signed-off-by: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2.6.16-rc3 uses hugetlb on-demand paging, but it doesn_t support hugetlb
mprotect.
From: David Gibson <david@gibson.dropbear.id.au>
Remove a test from the mprotect() path which checks that the mprotect()ed
range on a hugepage VMA is hugepage aligned (yes, really, the sense of
is_aligned_hugepage_range() is the opposite of what you'd guess :-/).
In fact, we don't need this test. If the given addresses match the
beginning/end of a hugepage VMA they must already be suitably aligned. If
they don't, then mprotect_fixup() will attempt to split the VMA. The very
first test in split_vma() will check for a badly aligned address on a
hugepage VMA and return -EINVAL if necessary.
From: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
On i386 and x86-64, pte flag _PAGE_PSE collides with _PAGE_PROTNONE. The
identify of hugetlb pte is lost when changing page protection via mprotect.
A page fault occurs later will trigger a bug check in huge_pte_alloc().
The fix is to always make new pte a hugetlb pte and also to clean up
legacy code where _PAGE_PRESENT is forced on in the pre-faulting day.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
check_acpi_pci() is called from arch/i386/kernel/setup.c even if
CONFIG_ACPI is not defined, but the code in include/asm/acpi.h doesn't
provide it in this case.
Signed-off-by: Herbert Pötzl <herbert@13thfloor.at>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ATI chipsets tend to generate double timer interrupts for the local APIC
timer when both the 8254 and the IO-APIC timer pins are enabled. This is
because they route it to both and the result is anded together and the CPU
ends up processing it twice.
This patch changes check_timer to disable the 8254 routing for interrupt 0.
I think it would be safe on all chipsets actually (i tested it on a couple
and it worked everywhere) and Windows seems to do it in a similar way, but
to be conservative this patch only enables this mode on ATI (and adds
options to enable/disable too)
Ported over from a similar x86-64 change.
I reused the ACPI earlyquirk infrastructure for the ATI bridge check, but
tweaked it a bit to work even without ACPI.
Inspired by a patch from Chuck Ebbert, but redone.
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Recent GDT changes broke the SMP boot sequence if the booting CPU is
numbered anything other than zero. There's also a subtle source of error
in that the boot time CPU now uses cpu_gdt_table (which is actually the GDT
for booting CPUs in head.S). This patch fixes both problems by making GDT
descriptors themselves allocated from a per_cpu area and switching to them
in cpu_init(), which now means that cpu_gdt_table is exclusively used for
booting CPUs again.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Matt Tolentino <metolent@snoqualmie.dp.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a problem seen on i686 machine with NX support where the instruction
could not be single stepped because of NX bit set on the memory pages
allocated by kprobes module. This patch provides allocation of instruction
solt so that the processor can execute the instruction from that location
similar to x86_64 architecture. Thanks to Bibo and Masami for testing this
patch.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not mask TIF_SINGLESTEP bit in _TIF_WORK_MASK. Masking this stopped
do_notify_resume() from being called when it should have been.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make new MADV_REMOVE, MADV_DONTFORK, MADV_DOFORK consistent across all
arches. The idea is to make it possible to use them portably even before
distros include them in libc headers.
Move common flags to asm-generic/mman.h
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, copy-on-write may change the physical address of a page even if the
user requested that the page is pinned in memory (either by mlock or by
get_user_pages). This happens if the process forks meanwhile, and the parent
writes to that page. As a result, the page is orphaned: in case of
get_user_pages, the application will never see any data hardware DMA's into
this page after the COW. In case of mlock'd memory, the parent is not getting
the realtime/security benefits of mlock.
In particular, this affects the Infiniband modules which do DMA from and into
user pages all the time.
This patch adds madvise options to control whether memory range is inherited
across fork. Useful e.g. for when hardware is doing DMA from/into these
pages. Could also be useful to an application wanting to speed up its forks
by cutting large areas out of consideration.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The correct way to export hyperthreading based functions is to predicate
them on CONFIG_X86_HT. Without this, the topology exporting patch breaks
the build on all non-PC x86 subarchitectures.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The *at patches introduced fstatat and, due to inusfficient research, I
used the newfstat functions generally as the guideline. The result is that
on 32-bit platforms we don't have all the information needed to implement
fstatat64.
This patch modifies the code to pass up 64-bit information if
__ARCH_WANT_STAT64 is defined. I renamed the syscall entry point to make
this clear. Other archs will continue to use the existing code. On x86-64
the compat code is implemented using a new sys32_ function. this is what
is done for the other stat syscalls as well.
This patch might break some other archs (those which define
__ARCH_WANT_STAT64 and which already wired up the syscall). Yet others
might need changes to accomodate the compatibility mode. I really don't
want to do that work because all this stat handling is a mess (more so in
glibc, but the kernel is also affected). It should be done by the arch
maintainers. I'll provide some stand-alone test shortly. Those who are
eager could compile glibc and run 'make check' (no installation needed).
The patch below has been tested on x86 and x86-64.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Registers system call for the i386 architecture.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix gcc4.1 compile warnings "value computed is not used" with
set_current_state() and set_task_state() on i386/SMP and x86-64.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch implements cpu topology exportation by sysfs.
Items (attributes) are similar to /proc/cpuinfo.
1) /sys/devices/system/cpu/cpuX/topology/physical_package_id:
represent the physical package id of cpu X;
2) /sys/devices/system/cpu/cpuX/topology/core_id:
represent the cpu core id to cpu X;
3) /sys/devices/system/cpu/cpuX/topology/thread_siblings:
represent the thread siblings to cpu X in the same core;
4) /sys/devices/system/cpu/cpuX/topology/core_siblings:
represent the thread siblings to cpu X in the same physical package;
To implement it in an architecture-neutral way, a new source file,
driver/base/topology.c, is to export the 5 attributes.
If one architecture wants to support this feature, it just needs to
implement 4 defines, typically in file include/asm-XXX/topology.h.
The 4 defines are:
#define topology_physical_package_id(cpu)
#define topology_core_id(cpu)
#define topology_thread_siblings(cpu)
#define topology_core_siblings(cpu)
The type of **_id is int.
The type of siblings is cpumask_t.
To be consistent on all architectures, the 4 attributes should have
deafult values if their values are unavailable. Below is the rule.
1) physical_package_id: If cpu has no physical package id, -1 is the
default value.
2) core_id: If cpu doesn't support multi-core, its core id is 0.
3) thread_siblings: Just include itself, if the cpu doesn't support
HT/multi-thread.
4) core_siblings: Just include itself, if the cpu doesn't support
multi-core and HT/Multi-thread.
So be careful when declaring the 4 defines in include/asm-XXX/topology.h.
If an attribute isn't defined on an architecture, it won't be exported.
Thank Nathan, Greg, Andi, Paul and Venki.
The patch provides defines for i386/x86_64/ia64.
Signed-off-by: Zhang, Yanmin <yanmin.zhang@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable selection of different user/kernel VM splits for i386, including an
optimized mode for 1GB physical RAM, which gives the kernel a direct (non
HIGHMEM) mapping to the entire 1GB rather than just the first 896MB.
There is a similarly a similarly optimized mode for machines with exactly 2GB
of physical RAM.
This can speed up the kernel by avoiding having to create/destroy temporary
HIGHMEM mappings, and by not having to include HIGHMEM support at all on such
machines. The flip side is that there's less virtual addressing left for
userspace in these alternatives, and some binary-only kernel modules may
misbehave unless rebuilt with the same VMSPLIT option as the main kernel
image.
Original idea/patch from Jens Axboe, modified based on suggestions from Linus
et al.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a subset of the bluesmoke project core code, stripped of the NMI work
which isn't ready to merge and some of the "interesting" proc functionality
that needs reworking or just has no place in kernel. It requires no core
kernel changes except the added scrub functions already posted.
The goal is to merge further functionality only after the core code is
accepted and proven in the base kernel, and only at the point the upstream
extras are really ready to merge.
From: doug thompson <norsk5@xmission.com>
This converts EDAC to sysfs and is the final chunk neccessary before EDAC
has a stable user space API and can be considered for submission into the
base kernel.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: doug thompson <norsk5@xmission.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EDAC requires a way to scrub memory if an ECC error is found and the chipset
does not do the work automatically. That means rewriting memory locations
atomically with respect to all CPUs _and_ bus masters. That means we can't
use atomic_add(foo, 0) as it gets optimised for non-SMP
This adds a function to include/asm-foo/atomic.h for the platforms currently
supported which implements a scrub of a mapped block.
It also adjusts a few other files include order where atomic.h is included
before types.h as this now causes an error as atomic_scrub uses u32.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the sys_pselect6() and sys_poll() calls to the i386 syscall table.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle TIF_RESTORE_SIGMASK as added by David Woodhouse's patch entitled:
[PATCH] 2/3 Add TIF_RESTORE_SIGMASK support for arch/powerpc
[PATCH] 3/3 Generic sys_rt_sigsuspend
It does the following:
(1) Declares TIF_RESTORE_SIGMASK for i386.
(2) Invokes it over to do_signal() when TIF_RESTORE_SIGMASK is set.
(3) Makes do_signal() support TIF_RESTORE_SIGMASK, using the signal mask saved
in current->saved_sigmask.
(4) Discards sys_rt_sigsuspend() from the arch, using the generic one instead.
(5) Makes sys_sigsuspend() save the signal mask and set TIF_RESTORE_SIGMASK
rather than attempting to fudge the return registers.
(6) Makes sys_sigsuspend() return -ERESTARTNOHAND rather than looping
intrinsically.
(7) Makes setup_frame(), setup_rt_frame() and handle_signal() return 0 or
-EFAULT rather than true/false to be consistent with the rest of the
kernel.
Due to the fact do_signal() is then only called from one place:
(8) Makes do_signal() no longer have a return value is it was just being
ignored; force_sig() takes care of this.
(9) Discards the old sigmask argument to do_signal() as it's no longer
necessary.
(10) Makes do_signal() static.
(11) Marks the second argument to do_notify_resume() as unused. The unused
argument should remain in the middle as the arguments are passed in as
registers, and the ordering is specific in entry.S
Given the way do_signal() is now no longer called from sys_{,rt_}sigsuspend(),
they no longer need access to the exception frame, and so can just take
arguments normally.
This patch depends on sys_rt_sigsuspend patch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Wire up the x86 syscalls
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I added this line to share this file with UML, but now it's no longer
shared so remove this useless leftover.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arjan van de Ven <arjan@infradead.org>
Mark a number of functions as 'must inline'. The functions affected by this
patch need to be inlined because they use knowledge that their arguments are
constant so that most of the function optimizes away. At this point this
patch does not change behavior, it's for documentation only (and for future
patches in the inline series)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
{get,put}_thread_info() were introduced in 2.5.4 and never
had been called by anything in the tree.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Al Viro <viro@ftp.linux.org.uk>
task_pt_regs() needs the same offset-by-8 to match copy_thread()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Ingo Molnar <mingo@elte.hu>
This is the latest version of the scheduler cache-hot-auto-tune patch.
The first problem was that detection time scaled with O(N^2), which is
unacceptable on larger SMP and NUMA systems. To solve this:
- I've added a 'domain distance' function, which is used to cache
measurement results. Each distance is only measured once. This means
that e.g. on NUMA distances of 0, 1 and 2 might be measured, on HT
distances 0 and 1, and on SMP distance 0 is measured. The code walks
the domain tree to determine the distance, so it automatically follows
whatever hierarchy an architecture sets up. This cuts down on the boot
time significantly and removes the O(N^2) limit. The only assumption
is that migration costs can be expressed as a function of domain
distance - this covers the overwhelming majority of existing systems,
and is a good guess even for more assymetric systems.
[ People hacking systems that have assymetries that break this
assumption (e.g. different CPU speeds) should experiment a bit with
the cpu_distance() function. Adding a ->migration_distance factor to
the domain structure would be one possible solution - but lets first
see the problem systems, if they exist at all. Lets not overdesign. ]
Another problem was that only a single cache-size was used for measuring
the cost of migration, and most architectures didnt set that variable
up. Furthermore, a single cache-size does not fit NUMA hierarchies with
L3 caches and does not fit HT setups, where different CPUs will often
have different 'effective cache sizes'. To solve this problem:
- Instead of relying on a single cache-size provided by the platform and
sticking to it, the code now auto-detects the 'effective migration
cost' between two measured CPUs, via iterating through a wide range of
cachesizes. The code searches for the maximum migration cost, which
occurs when the working set of the test-workload falls just below the
'effective cache size'. I.e. real-life optimized search is done for
the maximum migration cost, between two real CPUs.
This, amongst other things, has the positive effect hat if e.g. two
CPUs share a L2/L3 cache, a different (and accurate) migration cost
will be found than between two CPUs on the same system that dont share
any caches.
(The reliable measurement of migration costs is tricky - see the source
for details.)
Furthermore i've added various boot-time options to override/tune
migration behavior.
Firstly, there's a blanket override for autodetection:
migration_cost=1000,2000,3000
will override the depth 0/1/2 values with 1msec/2msec/3msec values.
Secondly, there's a global factor that can be used to increase (or
decrease) the autodetected values:
migration_factor=120
will increase the autodetected values by 20%. This option is useful to
tune things in a workload-dependent way - e.g. if a workload is
cache-insensitive then CPU utilization can be maximized by specifying
migration_factor=0.
I've tested the autodetection code quite extensively on x86, on 3
P3/Xeon/2MB, and the autodetected values look pretty good:
Dual Celeron (128K L2 cache):
---------------------
migration cost matrix (max_cache_size: 131072, cpu: 467 MHz):
---------------------
[00] [01]
[00]: - 1.7(1)
[01]: 1.7(1) -
---------------------
cacheflush times [2]: 0.0 (0) 1.7 (1784008)
---------------------
Here the slow memory subsystem dominates system performance, and even
though caches are small, the migration cost is 1.7 msecs.
Dual HT P4 (512K L2 cache):
---------------------
migration cost matrix (max_cache_size: 524288, cpu: 2379 MHz):
---------------------
[00] [01] [02] [03]
[00]: - 0.4(1) 0.0(0) 0.4(1)
[01]: 0.4(1) - 0.4(1) 0.0(0)
[02]: 0.0(0) 0.4(1) - 0.4(1)
[03]: 0.4(1) 0.0(0) 0.4(1) -
---------------------
cacheflush times [2]: 0.0 (33900) 0.4 (448514)
---------------------
Here it can be seen that there is no migration cost between two HT
siblings (CPU#0/2 and CPU#1/3 are separate physical CPUs). A fast memory
system makes inter-physical-CPU migration pretty cheap: 0.4 msecs.
8-way P3/Xeon [2MB L2 cache]:
---------------------
migration cost matrix (max_cache_size: 2097152, cpu: 700 MHz):
---------------------
[00] [01] [02] [03] [04] [05] [06] [07]
[00]: - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[01]: 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[02]: 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[03]: 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1) 19.2(1)
[04]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1) 19.2(1)
[05]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1) 19.2(1)
[06]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) - 19.2(1)
[07]: 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) 19.2(1) -
---------------------
cacheflush times [2]: 0.0 (0) 19.2 (19281756)
---------------------
This one has huge caches and a relatively slow memory subsystem - so the
migration cost is 19 msecs.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: <wilder@us.ibm.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add per-arch sched_cacheflush() which is a write-back cacheflush used by
the migration-cost calibration code at bootup time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Passing random input values in eax to cpuid is not a good idea
because the CPU will GPF for unknown ones.
Use the correct x86-64 version that exists for a longer time too.
This also adds a memory barrier to prevent the optimizer from
reordering.
Cc: tigran@veritas.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As suggested by Linus.
This catches driver bugs that could cause corruption on IOMMU architectures.
Also I converted the BUGs to out_of_line_bug()s to save a bit
of text space.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whenever we see that a CPU is capable of C3 (during ACPI cstate init), we
disable local APIC timer and switch to using a broadcast from external timer
interrupt (IRQ 0). This is needed because Intel CPUs stop the local
APIC timer in C3. This is currently only enabled for Intel CPUs.
Patch below adds the code for i386 and also the ACPI hunk.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some people need it now on 64bit so reuse the i386 code for
x86-64. This will be also useful for future bug workarounds.
It is a bit simplified there because there is no need
to do it very early on x86-64. This means it doesn't need
early ioremap et.al. We run it as a core initcall right now.
I hope it's not needed for early setup.
I added a general CONFIG_DMI symbol in case IA64 or someone
else wants to reuse the code later too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed that some lowlevel send_IPI_mask helpers had a hotplug/preempt
race whereupon the cpu_online_map was read before disabling preemption;
...
cpumask_t mask = cpu_online_map;
int cpu = get_cpu();
cpu_clear(cpu, mask);
...
But then i realised that there is no need for these lowlevel functions to
be going through all this trouble when all the callers are already made
hotplug/preempt safe.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Print bits for RDTSCP, SVM, CR8-LEGACY.
Also now print power flags on i386 like x86-64 always did.
This will add a new line in the 386 cpuinfo, but that shouldn't
be an issue - did that in the past too and I haven't heard
of any breakage.
I shrunk some of the fields in the i386 cpuinfo_x86 to chars
to make up for the new int "x86_power" field. Overall it's
smaller than before.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define it for i386 too.
This is a synthetic flag that signifies that the CPU's TSC runs
at a constant P state invariant frequency.
Fix up the logic on x86-64/i386 to set it on all known CPUs.
Use the AMD defined bit to set it on future AMD CPUs.
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noticed by Arjan originally on x86-64, then Ingo on x86, and finally me
grepping for it in the generic version.
Bad parenthesis nesting.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call the mutex slowpath more conservatively - e.g. FRAME_POINTERS can
change the calling convention, in which case a direct branch to the
slowpath becomes illegal. Bug found by Hugh Dickins.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch (against 2.6.15-rc5-mm3) fixes a kprobes build break
due to changes introduced in the kprobe locking in 2.6.15-rc5-mm3. In
addition, the patch reverts back the open-coding of kprobe_mutex.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently arch_remove_kprobes() is only implemented/required for x86_64 and
powerpc. All other architecture like IA64, i386 and sparc64 implementes a
dummy function which is being called from arch independent kprobes.c file.
This patch removes the dummy functions and replaces it with
#define arch_remove_kprobe(p, s) do { } while(0)
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The arch specific kprobes.h files never gets included when CONFIG_KPROBES is
turned off. Hence check for CONFIG_KPROBES is not appropriate here in this
arch specific kprobes.h files.
Also the below defined function kprobes_exception_notify() is not needed when
CONFIG_KPROBES is off.
Compile tested for both CONFIG_KPROBES=y and N.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most arches copied the i386 ioctl.h. Combine them into a generic header.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- If system panics then cpu register states are captured through funciton
crash_get_current_regs(). This is not a inline function hence a stack frame
is pushed on to the stack and then cpu register state is captured. Later
this frame is popped and new frames are pushed (machine_kexec).
- In theory this is not very right as we are capturing register states for a
frame and that frame is no more valid. This seems to have created back
trace problems for ppc64.
- This patch fixes it up. The very first thing it does after entering
crash_kexec() is to capture the register states. Anyway we don't want the
back trace beyond crash_kexec(). crash_get_current_regs() has been made
inline
- crash_setup_regs() is the top architecture dependent function which should
be responsible for capturing the register states as well as to do some
architecture dependent tricks. For ex. fixing up ss and esp for i386.
crash_setup_regs() has also been made inline to ensure no new call frame is
pushed onto stack.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- In case of system crash, current state of cpu registers is saved in memory
in elf note format. So far memory for storing elf notes was being allocated
statically for NR_CPUS.
- This patch introduces dynamic allocation of memory for storing elf notes.
It uses alloc_percpu() interface. This should lead to better memory usage.
- Introduced based on Andi Kleen's and Eric W. Biederman's suggestions.
- This patch also moves memory allocation for elf notes from architecture
dependent portion to architecture independent portion. Now crash_notes is
architecture independent. The whole idea is that size of memory to be
allocated per cpu (MAX_NOTE_BYTES) can be architecture dependent and
allocation of this memory can be architecture independent.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add the i386 version of mutex.h, optimized in assembly.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add atomic_xchg() to all the architectures. Needed by the new mutex code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
This adds an option to remove vm86 support under CONFIG_EMBEDDED. Saves
about 5k.
This version eliminates most of the #ifdefs of the previous version and
instead uses function stubs in vm86.h. Also, release_vm86_irqs is moved
from asm-i386/irq.h to a more appropriate home in vm86.h so that the stubs
can live together.
$ size vmlinux-baseline vmlinux-novm86
text data bss dec hex filename
2920821 523232 190652 3634705 377611 vmlinux-baseline
2916268 523100 190492 3629860 376324 vmlinux-novm86
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PTRACE_SYSEMU{,_SINGLESTEP} is actually arch specific, for now, and the
current allocated number clashes with a ptrace code of frv, i.e.
PTRACE_GETFDPIC. I should have submitted this much earlier, anyway we get no
breakage for this.
CC: Daniel Jacobowitz <dan@debian.org>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kill L1_CACHE_SHIFT from all arches. Since L1_CACHE_SHIFT_MAX is not used
anymore with the introduction of INTERNODE_CACHE, kill L1_CACHE_SHIFT_MAX.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_migrate_pages implementation using swap based page migration
This is the original API proposed by Ray Bryant in his posts during the first
half of 2005 on linux-mm@kvack.org and linux-kernel@vger.kernel.org.
The intent of sys_migrate is to migrate memory of a process. A process may
have migrated to another node. Memory was allocated optimally for the prior
context. sys_migrate_pages allows to shift the memory to the new node.
sys_migrate_pages is also useful if the processes available memory nodes have
changed through cpuset operations to manually move the processes memory. Paul
Jackson is working on an automated mechanism that will allow an automatic
migration if the cpuset of a process is changed. However, a user may decide
to manually control the migration.
This implementation is put into the policy layer since it uses concepts and
functions that are also needed for mbind and friends. The patch also provides
a do_migrate_pages function that may be useful for cpusets to automatically
move memory. sys_migrate_pages does not modify policies in contrast to Ray's
implementation.
The current code here is based on the swap based page migration capability and
thus is not able to preserve the physical layout relative to it containing
nodeset (which may be a cpuset). When direct page migration becomes available
then the implementation needs to be changed to do a isomorphic move of pages
between different nodesets. The current implementation simply evicts all
pages in source nodeset that are not in the target nodeset.
Patch supports ia64, i386 and x86_64.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GCC 4.1 gives the following warning: include/asm/mpspec.h:79: warning:
`packed' attribute ignored for field of type `unsigned char'
The packed attribute isn't really necessary anyways so just remove it.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Acked-by: Dave Jones <davej@codemonkey.org.uk>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide basic support for the AMD Geode GX and LX processors.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a single instruction on i386 to find largest set bit; so it makes
sense to use it (like we use bfs for ffs()).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we bring up a new CPU via INIT/startup IPI messages, the CPU that's
coming up sends a xTPR message to the chipset. Intel chipsets (at least)
don't provide any architectural guarantee on what the chipset will do with
this message. For example, the E850x chipsets uses this xTPR message to
interpret the interrupt operating mode of the platform. When the CPU
coming online sends this message, it always indicates that it is in logical
flat mode. For the CPU hotplug case, the platform may already be
functioning in cluster APIC mode at this time, the chipset can get confused
and mishandle I/O device and IPI interrupt routing.
The situation eventually gets corrected when the new CPU sends another xTPR
update when we switch it to cluster mode, but there's a window during which
the chipset may be in an inconsistent state. This patch avoids this
problem by using the flat physical interrupt delivery mode instead of
cluster mode for bigsmp (>8 cpu) support.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86 specific parts to make the .rodata section read only
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make i386's find_first_bit() use an unsigned integer as a counter to avoid
getting warnings when -Wsign-compare is given.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The one remaining caller of set_limit, the PnP BIOS code, calls into the PnP
BIOS, passing kernel parameters in and out. These parameteres may be passed
from arbitrary kernel virtual memory, so they deserve strict protection to
stop a bad BIOS from smashing beyond the object size.
Unfortunately, the use of set_limit was badly botching this by setting the
limit in terms of pages, when it really should have byte granularity.
When doing this, I discovered my BIOS had the buggy code during the "get
system device node" call:
mov ax, es:[bx]
Which is harmless, but has a trivial workaround.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Old accessors to fetch LDT descriptors are unused and outdated and in the
wrong header file.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move PnP BIOS segment definitions into segment.h; the segments are reserved
here, so they might as well be defined here as well.
Note I didn't do this for APM BIOS, as Macintosh and other systems use those
values to emulate APM in some scary way I don't want to understand.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
So some 486 processors do have CR4 register. Allow them to present it in
register dumps by using the old fault technique rather than testing processor
family.
Thanks to Maciej for noticing this.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move some code unrelated to any dealing with hardware bugs from i386's
bugs.h to a more logical place.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make GDT page aligned and page padded to support running inside of a
hypervisor. This prevents false sharing of the GDT page with other hot
data, which is not allowed in Xen, and causes performance problems in
VMware.
Rather than go back to the old method of statically allocating the GDT
(which wastes unneded space for non-present CPUs), the GDT for APs is
allocated dynamically.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Several counters already have the need to use 64 atomic variables on 64 bit
platforms (see mm_counter_t in sched.h). We have to do ugly ifdefs to fall
back to 32 bit atomic on 32 bit platforms.
The VM statistics patch that I am working on will also make more extensive
use of atomic64.
This patch introduces a new type atomic_long_t by providing definitions in
asm-generic/atomic.h that works similar to the c "long" type. Its 32 bits
on 32 bit platforms and 64 bits on 64 bit platforms.
Also cleans up the determination of the mm_counter_t in sched.h.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the last bits of Martin's ill-fated sys_set_zone_reclaim().
Cc: Martin Hicks <mort@wildopensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kvaddr_to_nid() isn't used in common code nor in i386 code. Remove these
definitions.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is the patch to implement madvise(MADV_REMOVE) - which frees up a
given range of pages & its associated backing store. Current
implementation supports only shmfs/tmpfs and other filesystems return
-ENOSYS.
"Some app allocates large tmpfs files, then when some task quits and some
client disconnect, some memory can be released. However the only way to
release tmpfs-swap is to MADV_REMOVE". - Andrea Arcangeli
Databases want to use this feature to drop a section of their bufferpool
(shared memory segments) - without writing back to disk/swap space.
This feature is also useful for supporting hot-plug memory on UML.
Concerns raised by Andrew Morton:
- "We have no plan for holepunching! If we _do_ have such a plan (or
might in the future) then what would the API look like? I think
sys_holepunch(fd, start, len), so we should start out with that."
- Using madvise is very weird, because people will ask "why do I need to
mmap my file before I can stick a hole in it?"
- None of the other madvise operations call into the filesystem in this
manner. A broad question is: is this capability an MM operation or a
filesytem operation? truncate, for example, is a filesystem operation
which sometimes has MM side-effects. madvise is an mm operation and with
this patch, it gains FS side-effects, only they're really, really
significant ones."
Comments:
- Andrea suggested the fs operation too but then it's more efficient to
have it as a mm operation with fs side effects, because they don't
immediatly know fd and physical offset of the range. It's possible to
fixup in userland and to use the fs operation but it's more expensive,
the vmas are already in the kernel and we can use them.
Short term plan & Future Direction:
- We seem to need this interface only for shmfs/tmpfs files in the short
term. We have to add hooks into the filesystem for correctness and
completeness. This is what this patch does.
- In the future, plan is to support both fs and mmap apis also. This
also involves (other) filesystem specific functions to be implemented.
- Current patch doesn't support VM_NONLINEAR - which can be addressed in
the future.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andrea Arcangeli <andrea@suse.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In commit 3D59121003721a8fad11ee72e646fd9d3076b5679c, the x86 and x86-64
<asm/param.h> was changed to include <linux/config.h> for the
configurable timer frequency.
However, asm/param.h is sometimes used in userland (it is included
indirectly from <sys/param.h>), so your commit pollutes the userland
namespace with tons of CONFIG_FOO macros. This greatly confuses
software packages (such as BusyBox) which use CONFIG_FOO macros
themselves to control the inclusion of optional features.
After a short exchange, Christoph approved this patch
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linux invokes the AML _PDC method (Processor Driver Capabilities)
to tell the BIOS what features it can handle. While the ACPI
spec says nothing about the OS invoking _PDC multiple times,
doing so with changing bits seems to hopelessly confuse the BIOS
on multiple platforms up to and including crashing the system.
Factor out the _PDC invocation so Linux invokes it only once.
http://bugzilla.kernel.org/show_bug.cgi?id=5483
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Due to incomplete memory constraints, gcc would miscompile code with
sigaddset on i386 if sig arg was const.
A quote form Jakub to make the issue clear:
"You need either
__asm__("btsl %1,%0" : "+m"(*set) : "Ir"(_sig-1) : "cc");
or
__asm__("btsl %1,%0" : "=m"(*set) : "Ir"(_sig-1), "m"(*set) : "cc");
because the btsl instruction doesn't just set the memory to some
value, but needs to read its previous content as well. If you don't
tell that fact to GCC, GCC is of course free to optimize as if the asm
was just setting the value and not depended on the previous value."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Old code could retry for 10 seconds worst time. Only try it
for one second now.
Suggested by Yinghai Lu
Cc: Yinghai.Lu@amd.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fields obtained through cpuid vector 0x1(ebx[16:23]) and
vector 0x4(eax[14:25], eax[26:31]) indicate the maximum values and might not
always be the same as what is available and what OS sees. So make sure
"siblings" and "cpu cores" values in /proc/cpuinfo reflect the values as seen
by OS instead of what cpuid instruction says. This will also fix the buggy BIOS
cases (for example where cpuid on a single core cpu says there are "2" siblings,
even when HT is disabled in the BIOS.
http://bugzilla.kernel.org/show_bug.cgi?id=4359)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce an atomic_inc_not_zero operation. Make this a special case of
atomic_add_unless because lockless pagecache actually wants
atomic_inc_not_negativeone due to its offset refcount.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Make cmpxchg generally available on the i386 platform.
- Provide emulation of cmpxchg suitable for uniprocessor if built and run on
386.
From: Christoph Lameter <clameter@sgi.com>
- Cut down patch and small style changes.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MSI hardcoded delivery mode to use logical delivery mode. Recently
x86_64 moved to use physical mode addressing to support physflat mode.
With this mode enabled noticed that my eth with MSI werent working.
msi_address_init() was hardcoded to use logical mode for i386 and x86_64.
So when we switch to use physical mode, things stopped working.
Since anyway we dont use lowest priority delivery with MSI, its always
directed to just a single CPU. Its safe and simpler to use
physical mode always, even when we use logical delivery mode for IPI's
or other ioapic RTE's.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Wilcox asked that this got a comment explaining why it is done
so here it is.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
I386 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu, using an arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's widely seen a MCE non-fatal error reported after resume. It seems MCE
resume is lacked under ia32. This patch tries to fix the gap.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit f2b36db692 causes a bootup hang on
at least one machine. Revert for now until we understand why. The old
code may be ugly, but it works.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__MUTEX_INITIALIZER() has no users, and equates to the more commonly used
DECLARE_MUTEX(), thus making it pretty much redundant. Remove it for good.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes page_pte_prot and page_pte macros from all
architectures. Some architectures define both, some only page_pte (broken)
and others none. These macros are not used anywhere.
page_pte_prot(page, prot) is identical to mk_pte(page, prot) and
page_pte(page) is identical to page_pte_prot(page, __pgprot(0)).
* The following architectures define both page_pte_prot and page_pte
arm, arm26, ia64, sh64, sparc, sparc64
* The following architectures define only page_pte (broken)
frv, i386, m32r, mips, sh, x86-64
* All other architectures define neither
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure we always return, as all syscalls should. Also move the common
prototype to <linux/syscalls.h>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All kinds of ugliness exists because we don't initialize
the apics during init_IRQs.
- We calibrate jiffies in non apic mode even when we are using apics.
- We have to have special code to initialize the apics when non-smp.
- The legacy i8259 must exist and be setup correctly, even
when we won't use it past initialization.
- The kexec on panic code must restore the state of the io_apics.
- init/main.c needs a special case for !smp smp_init on x86
In addition to pure code movement I needed a couple
of non-obvious changes:
- Move setup_boot_APIC_clock into APIC_late_time_init for
simplicity.
- Use cpu_khz to generate a better approximation of loops_per_jiffies
so I can verify the timer interrupt is working.
- Call setup_apic_nmi_watchdog again after cpu_khz is initialized on
the boot cpu.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is platform code update for ES7000: disables IRQ overrides for the
recent ES7000 (Rascal/Zorro), cleans up the compile warning. The patch
only affects the ES7000 subarch.
Signed-off-by: <Natalie.Protasevich@unisys.com>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an accessor function for getting the per-CPU gdt. Callee must already
have the CPU.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Join together some common functions (pmd_page{,_kernel}) over 2level and
3level pages.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adjusts i386's cmpxchg patterns so that
- for word and long cmpxchg-es the compiler can utilize all possible
registers
- cmpxchg8b gets disabled when the minimum specified hardware architectur
doesn't support it (like was already happening for the byte, word, and
long ones).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following series implements memory hot-add for ppc64 and i386. There are
x86_64 and ia64 implementations that will be submitted shortly as well,
through the normal maintainers.
This patch:
local_mapnr is unused, except for in an alpha header. Keep the alpha one,
kill the rest.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert those common loops using page_table_lock on the outside and
pte_offset_map within to use just pte_offset_map_lock within instead.
These all hold mmap_sem (some exclusively, some not), so at no level can a
page table be whipped away from beneath them. But whereas pte_alloc loops
tested with the "atomic" pmd_present, these loops are testing with pmd_none,
which on i386 PAE tests both lower and upper halves.
That's now unsafe, so add a cast into pmd_none to test only the vital lower
half: we lose a little sensitivity to a corrupt middle directory, but not
enough to worry about. It appears that i386 and UML were the only
architectures vulnerable in this way, and pgd and pud no problem.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add sem_is_read/write_locked functions to the read/write semaphores, along the
same lines of the *_is_locked spinlock functions. The swap token tuning patch
uses sem_is_read_locked; sem_is_write_locked is added for completeness.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This revised patch (as586b) makes usb-handoff permanently true and no
longer a kernel boot parameter. It also removes the piix3_usb quirk code;
that was nothing more than an early version of the USB handoff code
(written at a time when Intel's PIIX3 was about the only motherboard with
USB support). And it adds identifiers for the three PCI USB controller
classes to pci_ids.h.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
include/asm/hw_irq.h:70: warning: `struct hw_interrupt_type' declared inside parameter list
include/asm/hw_irq.h:70: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Follow up to 4732efbeb9 - uml must just reuse
as-is the backing architecture support. There is a micro-fixup is needed for the
included file, which won't affect i386 behaviour at all.
I've not tested compilation on x86_64, only on x86, but the code is almost the
same except the culprit test, so everything should be ok on x86_64 too.
Cc: Jakub Jelinek <jakub@redhat.com>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As written in Documentation/feature-removal-schedule.txt, remove the
io_remap_page_range() kernel API.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original patch from Bertro Simul
This is probably still not quite correct, but seems to be
the best solution so far.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As noted by matz@suse.de
The problem is, that on i386 the syscallN
macro is defined like so:
long __res; \
__asm__ volatile ("int $0x80" \
: "=a" (__res) \
: "0" (__NR_##name),"b" ((long)(arg1)),"c" ((long)(arg2)), \
"d" ((long)(arg3)),"S" ((long)(arg4)),"D" ((long)(arg5))); \
If one of the arguments (in the _llseek syscall it's the arg4) is a pointer
which the syscall is expected to write to (to the memory pointed to by this
ptr), then this side-effect is not captured in the asm.
If anyone uses this macro to define it's own version of the syscall
(sometimes necessary when not using glibc) and it's inlined, then GCC
doesn't know that this asm write to "*dest", when called like so for instance:
out = 1;
llseek (fd, bla, blubb, &out, trara)
use (out);
Here nobody tells GCC that "out" actually is written to (just a pointer to it
is passed to the asm). Hence GCC might (and in the above bug did)
copy-propagate "1" into the second use of "out".
The easiest solution would be to add a "memory" clobber to the definition
of this syscall macro. As this is a syscall, it shouldn't inhibit too many
optimizations.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
"extern inline" doesn't make much sense.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch (written by me and also containing many suggestions of Arjan van
de Ven) does a major cleanup of the spinlock code. It does the following
things:
- consolidates and enhances the spinlock/rwlock debugging code
- simplifies the asm/spinlock.h files
- encapsulates the raw spinlock type and moves generic spinlock
features (such as ->break_lock) into the generic code.
- cleans up the spinlock code hierarchy to get rid of the spaghetti.
Most notably there's now only a single variant of the debugging code,
located in lib/spinlock_debug.c. (previously we had one SMP debugging
variant per architecture, plus a separate generic one for UP builds)
Also, i've enhanced the rwlock debugging facility, it will now track
write-owners. There is new spinlock-owner/CPU-tracking on SMP builds too.
All locks have lockup detection now, which will work for both soft and hard
spin/rwlock lockups.
The arch-level include files now only contain the minimally necessary
subset of the spinlock code - all the rest that can be generalized now
lives in the generic headers:
include/asm-i386/spinlock_types.h | 16
include/asm-x86_64/spinlock_types.h | 16
I have also split up the various spinlock variants into separate files,
making it easier to see which does what. The new layout is:
SMP | UP
----------------------------|-----------------------------------
asm/spinlock_types_smp.h | linux/spinlock_types_up.h
linux/spinlock_types.h | linux/spinlock_types.h
asm/spinlock_smp.h | linux/spinlock_up.h
linux/spinlock_api_smp.h | linux/spinlock_api_up.h
linux/spinlock.h | linux/spinlock.h
/*
* here's the role of the various spinlock/rwlock related include files:
*
* on SMP builds:
*
* asm/spinlock_types.h: contains the raw_spinlock_t/raw_rwlock_t and the
* initializers
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* asm/spinlock.h: contains the __raw_spin_*()/etc. lowlevel
* implementations, mostly inline assembly code
*
* (also included on UP-debug builds:)
*
* linux/spinlock_api_smp.h:
* contains the prototypes for the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*
* on UP builds:
*
* linux/spinlock_type_up.h:
* contains the generic, simplified UP spinlock type.
* (which is an empty structure on non-debug builds)
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* linux/spinlock_up.h:
* contains the __raw_spin_*()/etc. version of UP
* builds. (which are NOPs on non-debug, non-preempt
* builds)
*
* (included on UP-non-debug builds:)
*
* linux/spinlock_api_up.h:
* builds the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*/
All SMP and UP architectures are converted by this patch.
arm, i386, ia64, ppc, ppc64, s390/s390x, x64 was build-tested via
crosscompilers. m32r, mips, sh, sparc, have not been tested yet, but should
be mostly fine.
From: Grant Grundler <grundler@parisc-linux.org>
Booted and lightly tested on a500-44 (64-bit, SMP kernel, dual CPU).
Builds 32-bit SMP kernel (not booted or tested). I did not try to build
non-SMP kernels. That should be trivial to fix up later if necessary.
I converted bit ops atomic_hash lock to raw_spinlock_t. Doing so avoids
some ugly nesting of linux/*.h and asm/*.h files. Those particular locks
are well tested and contained entirely inside arch specific code. I do NOT
expect any new issues to arise with them.
If someone does ever need to use debug/metrics with them, then they will
need to unravel this hairball between spinlocks, atomic ops, and bit ops
that exist only because parisc has exactly one atomic instruction: LDCW
(load and clear word).
From: "Luck, Tony" <tony.luck@intel.com>
ia64 fix
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjanv@infradead.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Mikael Pettersson <mikpe@csd.uu.se>
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have a system (Biostar IDEQ210M mini-pc with a VIA chipset) which will
not reboot unless a keyboard is plugged in to it. I have tried all
combinations of the kernel "reboot=x,y" flags to no avail. Rebooting by
any method will leave the system in a wedged state (at the "Restarting
system" message).
I finally tracked the problem down to the machine's refusal to fully reboot
unless the keyboard controller status register had bit 2 set. This is the
"System flag" which when set, indicates successful completion of the
keyboard controller self-test (Basic Assurance Test, BAT).
I suppose that something is trying to protect against sporadic reboots
unless the keyboard controller is in a good state (a keyboard is present),
but I need this machine to be headless.
I found that setting the system flag (via the command byte) before giving
the "pulse reset line" command will allow the reboot to proceed. The patch
is simple, and I think it should be fine for everybody whether they have
this type of machine or not. This affects the "hard" reboot (as done when
the kernel boot flags "reboot=c,h" are used).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Building asm-offsets.h has been moved to a seperate Kbuild file
located in the top-level directory. This allow us to share the
functionality across the architectures.
The old rules in architecture specific Makefiles will die
in subsequent patches.
Furhtermore the usual kbuild dependency tracking is now used
when deciding to rebuild asm-offsets.s. So we no longer risk
to fail a rebuild caused by asm-offsets.c dependencies being touched.
With this common rule-set we now force the same name across
all architectures. Following patches will fix the rest.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch gathers all the struct flock64 definitions (and the operations),
puts them under !CONFIG_64BIT and cleans up the arch files.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch just gathers together all the struct flock definitions except
xtensa into asm-generic/fcntl.h.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch puts the most popular of each fcntl operation/flag into
asm-generic/fcntl.h and cleans up the arch files.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch puts the most popular of each open flag into asm-generic/fcntl.h
and cleans up the arch files.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This set of patches creates asm-generic/fcntl.h and consolidates as much as
possible from the asm-*/fcntl.h files into it.
This patch just gathers all the identical bits of the asm-*/fcntl.h files into
asm-generic/fcntl.h.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
unused and useless..
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The size of auxiliary vector is fixed at 42 in linux/sched.h. But it isn't
very obvious when looking at linux/elf.h. This patch adds AT_VECTOR_SIZE
so that we can change it if necessary when a new vector is added.
Because of include file ordering problems, doing this necessitated the
extraction of the AT_* symbols into a standalone header file.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ATM pthread_cond_signal is unnecessarily slow, because it wakes one waiter
(which at least on UP usually means an immediate context switch to one of
the waiter threads). This waiter wakes up and after a few instructions it
attempts to acquire the cv internal lock, but that lock is still held by
the thread calling pthread_cond_signal. So it goes to sleep and eventually
the signalling thread is scheduled in, unlocks the internal lock and wakes
the waiter again.
Now, before 2003-09-21 NPTL was using FUTEX_REQUEUE in pthread_cond_signal
to avoid this performance issue, but it was removed when locks were
redesigned to the 3 state scheme (unlocked, locked uncontended, locked
contended).
Following scenario shows why simply using FUTEX_REQUEUE in
pthread_cond_signal together with using lll_mutex_unlock_force in place of
lll_mutex_unlock is not enough and probably why it has been disabled at
that time:
The number is value in cv->__data.__lock.
thr1 thr2 thr3
0 pthread_cond_wait
1 lll_mutex_lock (cv->__data.__lock)
0 lll_mutex_unlock (cv->__data.__lock)
0 lll_futex_wait (&cv->__data.__futex, futexval)
0 pthread_cond_signal
1 lll_mutex_lock (cv->__data.__lock)
1 pthread_cond_signal
2 lll_mutex_lock (cv->__data.__lock)
2 lll_futex_wait (&cv->__data.__lock, 2)
2 lll_futex_requeue (&cv->__data.__futex, 0, 1, &cv->__data.__lock)
# FUTEX_REQUEUE, not FUTEX_CMP_REQUEUE
2 lll_mutex_unlock_force (cv->__data.__lock)
0 cv->__data.__lock = 0
0 lll_futex_wake (&cv->__data.__lock, 1)
1 lll_mutex_lock (cv->__data.__lock)
0 lll_mutex_unlock (cv->__data.__lock)
# Here, lll_mutex_unlock doesn't know there are threads waiting
# on the internal cv's lock
Now, I believe it is possible to use FUTEX_REQUEUE in pthread_cond_signal,
but it will cost us not one, but 2 extra syscalls and, what's worse, one of
these extra syscalls will be done for every single waiting loop in
pthread_cond_*wait.
We would need to use lll_mutex_unlock_force in pthread_cond_signal after
requeue and lll_mutex_cond_lock in pthread_cond_*wait after lll_futex_wait.
Another alternative is to do the unlocking pthread_cond_signal needs to do
(the lock can't be unlocked before lll_futex_wake, as that is racy) in the
kernel.
I have implemented both variants, futex-requeue-glibc.patch is the first
one and futex-wake_op{,-glibc}.patch is the unlocking inside of the kernel.
The kernel interface allows userland to specify how exactly an unlocking
operation should look like (some atomic arithmetic operation with optional
constant argument and comparison of the previous futex value with another
constant).
It has been implemented just for ppc*, x86_64 and i?86, for other
architectures I'm including just a stub header which can be used as a
starting point by maintainers to write support for their arches and ATM
will just return -ENOSYS for FUTEX_WAKE_OP. The requeue patch has been
(lightly) tested just on x86_64, the wake_op patch on ppc64 kernel running
32-bit and 64-bit NPTL and x86_64 kernel running 32-bit and 64-bit NPTL.
With the following benchmark on UP x86-64 I get:
for i in nptl-orig nptl-requeue nptl-wake_op; do echo time elf/ld.so --library-path .:$i /tmp/bench; \
for j in 1 2; do echo ( time elf/ld.so --library-path .:$i /tmp/bench ) 2>&1; done; done
time elf/ld.so --library-path .:nptl-orig /tmp/bench
real 0m0.655s user 0m0.253s sys 0m0.403s
real 0m0.657s user 0m0.269s sys 0m0.388s
time elf/ld.so --library-path .:nptl-requeue /tmp/bench
real 0m0.496s user 0m0.225s sys 0m0.271s
real 0m0.531s user 0m0.242s sys 0m0.288s
time elf/ld.so --library-path .:nptl-wake_op /tmp/bench
real 0m0.380s user 0m0.176s sys 0m0.204s
real 0m0.382s user 0m0.175s sys 0m0.207s
The benchmark is at:
http://sourceware.org/ml/libc-alpha/2005-03/txt00001.txt
Older futex-requeue-glibc.patch version is at:
http://sourceware.org/ml/libc-alpha/2005-03/txt00002.txt
Older futex-wake_op-glibc.patch version is at:
http://sourceware.org/ml/libc-alpha/2005-03/txt00003.txt
Will post a new version (just x86-64 fixes so that the patch
applies against pthread_cond_signal.S) to libc-hacker ml soon.
Attached is the kernel FUTEX_WAKE_OP patch as well as a simple-minded
testcase that will not test the atomicity of the operation, but at least
check if the threads that should have been woken up are woken up and
whether the arithmetic operation in the kernel gave the expected results.
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Jamie Lokier <jamie@shareable.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike <jdike@addtoit.com>,
Paolo 'Blaisorblade' Giarrusso <blaisorblade_spam@yahoo.it>,
Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Adds a new ptrace(2) mode, called PTRACE_SYSEMU, resembling PTRACE_SYSCALL
except that the kernel does not execute the requested syscall; this is useful
to improve performance for virtual environments, like UML, which want to run
the syscall on their own.
In fact, using PTRACE_SYSCALL means stopping child execution twice, on entry
and on exit, and each time you also have two context switches; with SYSEMU you
avoid the 2nd stop and so save two context switches per syscall.
Also, some architectures don't have support in the host for changing the
syscall number via ptrace(), which is currently needed to skip syscall
execution (UML turns any syscall into getpid() to avoid it being executed on
the host). Fixing that is hard, while SYSEMU is easier to implement.
* This version of the patch includes some suggestions of Jeff Dike to avoid
adding any instructions to the syscall fast path, plus some other little
changes, by myself, to make it work even when the syscall is executed with
SYSENTER (but I'm unsure about them). It has been widely tested for quite a
lot of time.
* Various fixed were included to handle the various switches between
various states, i.e. when for instance a syscall entry is traced with one of
PT_SYSCALL / _SYSEMU / _SINGLESTEP and another one is used on exit.
Basically, this is done by remembering which one of them was used even after
the call to ptrace_notify().
* We're combining TIF_SYSCALL_EMU with TIF_SYSCALL_TRACE or TIF_SINGLESTEP
to make do_syscall_trace() notice that the current syscall was started with
SYSEMU on entry, so that no notification ought to be done in the exit path;
this is a bit of a hack, so this problem is solved in another way in next
patches.
* Also, the effects of the patch:
"Ptrace - i386: fix Syscall Audit interaction with singlestep"
are cancelled; they are restored back in the last patch of this series.
Detailed descriptions of the patches doing this kind of processing follow (but
I've already summed everything up).
* Fix behaviour when changing interception kind #1.
In do_syscall_trace(), we check the status of the TIF_SYSCALL_EMU flag
only after doing the debugger notification; but the debugger might have
changed the status of this flag because he continued execution with
PTRACE_SYSCALL, so this is wrong. This patch fixes it by saving the flag
status before calling ptrace_notify().
* Fix behaviour when changing interception kind #2:
avoid intercepting syscall on return when using SYSCALL again.
A guest process switching from using PTRACE_SYSEMU to PTRACE_SYSCALL
crashes.
The problem is in arch/i386/kernel/entry.S. The current SYSEMU patch
inhibits the syscall-handler to be called, but does not prevent
do_syscall_trace() to be called after this for syscall completion
interception.
The appended patch fixes this. It reuses the flag TIF_SYSCALL_EMU to
remember "we come from PTRACE_SYSEMU and now are in PTRACE_SYSCALL", since
the flag is unused in the depicted situation.
* Fix behaviour when changing interception kind #3:
avoid intercepting syscall on return when using SINGLESTEP.
When testing 2.6.9 and the skas3.v6 patch, with my latest patch and had
problems with singlestepping on UML in SKAS with SYSEMU. It looped
receiving SIGTRAPs without moving forward. EIP of the traced process was
the same for all SIGTRAPs.
What's missing is to handle switching from PTRACE_SYSCALL_EMU to
PTRACE_SINGLESTEP in a way very similar to what is done for the change from
PTRACE_SYSCALL_EMU to PTRACE_SYSCALL_TRACE.
I.e., after calling ptrace(PTRACE_SYSEMU), on the return path, the debugger is
notified and then wake ups the process; the syscall is executed (or skipped,
when do_syscall_trace() returns 0, i.e. when using PTRACE_SYSEMU), and
do_syscall_trace() is called again. Since we are on the return path of a
SYSEMU'd syscall, if the wake up is performed through ptrace(PTRACE_SYSCALL),
we must still avoid notifying the parent of the syscall exit. Now, this
behaviour is extended even to resuming with PTRACE_SINGLESTEP.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The timers lack .suspend/.resume methods. Because of this, jiffies got a
big compensation after a S3 resume. And then softlockup watchdog reports
an oops. This occured with HPET enabled, but it's also possible for other
timers.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
for_each_cpu walks through all processors in cpu_possible_map, which is
defined as cpu_callout_map on i386 and isn't initialised until all
processors have been booted. This breaks things which do for_each_cpu
iterations early during boot. So, define cpu_possible_map as a bitmap with
NR_CPUS bits populated. This was triggered by a patch i'm working on which
does alloc_percpu before bringing up secondary processors.
From: Alexander Nyberg <alexn@telia.com>
i386-boottime-for_each_cpu-broken.patch
i386-boottime-for_each_cpu-broken-fix.patch
The SMP version of __alloc_percpu checks the cpu_possible_map before
allocating memory for a certain cpu. With the above patches the BSP cpuid
is never set in cpu_possible_map which breaks CONFIG_SMP on uniprocessor
machines (as soon as someone tries to dereference something allocated via
__alloc_percpu, which in fact is never allocated since the cpu is not set
in cpu_possible_map).
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a clone operation for pgd updates.
This helps complete the encapsulation of updates to page tables (or pages
about to become page tables) into accessor functions rather than using
memcpy() to duplicate them. This is both generally good for consistency
and also necessary for running in a hypervisor which requires explicit
updates to page table entries.
The new function is:
clone_pgd_range(pgd_t *dst, pgd_t *src, int count);
dst - pointer to pgd range anwhere on a pgd page
src - ""
count - the number of pgds to copy.
dst and src can be on the same page, but the range must not overlap
and must not cross a page boundary.
Note that I ommitted using this call to copy pgd entries into the
software suspend page root, since this is not technically a live paging
structure, rather it is used on resume from suspend. CC'ing Pavel in case
he has any feedback on this.
Thanks to Chris Wright for noticing that this could be more optimal in
PAE compiles by eliminating the memset.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a notify to the die_nmi notify that the system is about to
be taken down. If the notify is handled with a NOTIFY_STOP return, the
system is given a new lease on life.
We also change the nmi watchdog to carry on if die_nmi returns.
This give debug code a chance to a) catch watchdog timeouts and b) possibly
allow the system to continue, realizing that the time out may be due to
debugger activities such as single stepping which is usually done with
"other" cpus held.
Signed-off-by: George Anzinger<george@mvista.com>
Cc: Keith Owens <kaos@ocs.com.au>
Signed-off-by: George Anzinger <george@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pushf/popf in switch_to are ONLY used to switch IOPL. Making this
explicit in C code is more clear. This pushf/popf pair was added as a
bugfix for leaking IOPL to unprivileged processes when using
sysenter/sysexit based system calls (sysexit does not restore flags).
When requesting an IOPL change in sys_iopl(), it is just as easy to change
the current flags and the flags in the stack image (in case an IRET is
required), but there is no reason to force an IRET if we came in from the
SYSENTER path.
This change is the minimal solution for supporting a paravirtualized Linux
kernel that allows user processes to run with I/O privilege. Other
solutions require radical rewrites of part of the low level fault / system
call handling code, or do not fully support sysenter based system calls.
Unfortunately, this added one field to the thread_struct. But as a bonus,
on P4, the fastest time measured for switch_to() went from 312 to 260
cycles, a win of about 17% in the fast case through this performance
critical path.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Privilege checking cleanup. Originally, these diffs were much greater, but
recent cleanups in Linux have already done much of the cleanup. I added
some explanatory comments in places where the reasoning behind certain
tests is rather subtle.
Also, in traps.c, we can skip the user_mode check in handle_BUG(). The
reason is, there are only two call chains - one via die_if_kernel() and one
via do_page_fault(), both entering from die(). Both of these paths already
ensure that a kernel mode failure has happened. Also, the original check
here, if (user_mode(regs)) was insufficient anyways, since it would not
rule out BUG faults from V8086 mode execution.
Saving the %ss segment in show_regs() rather than assuming a fixed value
also gives better information about the current kernel state in the
register dump.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some more assembler cleanups I noticed along the way.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noticed by Chuck Ebbert: the .ldt entry of the TSS was set up incorrectly.
It never mattered since this was a leftover from old times, so remove it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also, setting PDPEs in PAE mode does not require atomic operations, since the
PDPEs are cached by the processor, and only reloaded on an explicit or
implicit reload of CR3.
Since the four PDPEs must always be present in an active root, and the kernel
PDPE is never updated, we are safe even from SMIs and interrupts / NMIs using
task gates (which reload CR3). Actually, much of this is moot, since the user
PDPEs are never updated either, and the only usage of task gates is by the
doublefault handler. It appears the only place PGDs get updated in PAE mode
is in init_low_mappings() / zap_low_mapping() for initial page table creation
and recovery from ACPI sleep state, and these sites are safe by inspection.
Getting rid of the cmpxchg8b saves code space and 720 cycles in pgd_alloc on
P4.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GCC can generate better code around descriptor update and access functions
when there is not an explicit "eax" register constraint.
Testing: You won't boot if this is messed up, since the TSS descriptor will be
corrupted. Verified the assembler and booted.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 inline assembler cleanup.
This change encapsulates descriptor and task register management. Also,
it is possible to improve assembler generation in two cases; savesegment
may store the value in a register instead of a memory location, which
allows GCC to optimize stack variables into registers, and MOV MEM, SEG
is always a 16-bit write to memory, making the casting in math-emu
unnecessary.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 arch cleanup. Introduce the serialize macro to serialize processor
state. Why the microcode update needs it I am not quite sure, since wrmsr()
is already a serializing instruction, but it is a microcode update, so I will
keep the semantic the same, since this could be a timing workaround. As far
as I can tell, this has always been there since the original microcode update
source.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 Inline asm cleanup. Use cr/dr accessor functions.
Also, a potential bugfix. Also, some CR accessors really should be volatile.
Reads from CR0 (numeric state may change in an exception handler), writes to
CR4 (flipping CR4.TSD) and reads from CR2 (page fault) prevent instruction
re-ordering. I did not add memory clobber to CR3 / CR4 / CR0 updates, as it
was not there to begin with, and in no case should kernel memory be clobbered,
except when doing a TLB flush, which already has memory clobber.
I noticed that page invalidation does not have a memory clobber. I can't find
a bug as a result, but there is definitely a potential for a bug here:
#define __flush_tlb_single(addr) \
__asm__ __volatile__("invlpg %0": :"m" (*(char *) addr))
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is subarch update for ES7000. I've modified platform check code and
removed unnecessary OEM table parsing for newer systems that don't use OEM
information during boot. Parsing the table in fact is causing problems,
and the platform doesn't get recognized. The patch only affects the ES7000
subach.
Signed-off-by: <Natalie.Protasevich@unisys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 generic subarchitecture requires explicit dmi strings or command line
to enable bigsmp mode. The patch below removes that restriction, and uses
bigsmp as soon as it finds more than 8 logical CPUs, Intel processors and
xAPIC support.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The memory descriptors that comprise the EFI memory map are not fixed in
stone such that the size could change in the future. This uses the memory
descriptor size obtained from EFI to iterate over the memory map entries
during boot. This enables the removal of an x86 specific pad (and ifdef)
in the EFI header. I also couldn't stomach the broken up nature of the
function to put EFI runtime calls into virtual mode any longer so I fixed
that up a bit as well.
For reference, this patch only impacts x86.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new accessor for PTEs, which passes the full hint from the mmu_gather
struct; this allows architectures with hardware pagetables to optimize away
atomic PTE operations when destroying an address space. Removing the
locked operation should allow better pipelining of memory access in this
loop. I measured an average savings of 30-35 cycles per zap_pte_range on
the first 500 destructions on Pentium-M, but I believe the optimization
would win more on older processors which still assert the bus lock on xchg
for an exclusive cacheline.
Update: I made some new measurements, and this saves exactly 26 cycles over
ptep_get_and_clear on Pentium M. On P4, with a PAE kernel, this saves 180
cycles per ptep_get_and_clear, for a whopping 92160 cycles savings for a
full address space destruction.
pte_clear_full is not yet used, but is provided for future optimizations
(in particular, when running inside of a hypervisor that queues page table
updates, the full hint allows us to avoid queueing unnecessary page table
update for an address space in the process of being destroyed.
This is not a huge win, but it does help a bit, and sets the stage for
further hypervisor optimization of the mm layer on all architectures.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Christoph Lameter <christoph@lameter.com>
Cc: <linux-mm@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is used only in slab.c and each architecture gets to define whcih
underlying type is to be used.
Seems a bit silly - move it to slab.c and use the same type for all
architectures: unsigned int.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I don't think we need to call hugetlb_clean_stale_pgtable() anymore
in 2.6.13 because of the rework with free_pgtables(). It now collect
all the pte page at the time of munmap. It used to only collect page
table pages when entire one pgd can be freed and left with staled pte
pages. Not anymore with 2.6.13. This function will never be called
and We should turn it into a BUG_ON.
I also spotted two problems here, not Adam's fault :-)
(1) in huge_pte_alloc(), it looks like a bug to me that pud is not
checked before calling pmd_alloc()
(2) in hugetlb_clean_stale_pgtable(), it also missed a call to
pmd_free_tlb. I think a tlb flush is required to flush the mapping
for the page table itself when we clear out the pmd pointing to a
pte page. However, since hugetlb_clean_stale_pgtable() is never
called, so it won't trigger the bug.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: Adam Litke <agl@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a macro pte_huge(pte) for i386/x86_64 which is needed by a
patch later in the series. Instead of repeating (_PAGE_PRESENT |
_PAGE_PSE), I've added __LARGE_PTE to i386 to match x86_64.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: <linux-mm@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
_PAGE_FILE does not indicate whether a file is in page / swap cache, it is
set just for non-linear PTE's. Correct the comment for i386, x86_64, UML.
Also clearify _PAGE_NONE.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Someone mentioned that almost all the architectures used basically the same
implementation of get_order. This patch consolidates them into
asm-generic/page.h and includes that in the appropriate places. The
exceptions are ia64 and ppc which have their own (presumably optimised)
versions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete the ability to build an ACPI kernel that does
not include PCI support. When such a machine is created
and it requires a tuned kernel, send a patch.
http://bugzilla.kernel.org/show_bug.cgi?id=1364
Signed-off-by: Len Brown <len.brown@intel.com>
Chuck Ebbert noticed that the desc_empty macro is incorrect. Fix it.
Thankfully, this is not used as a security check, but it can falsely
overwrite TLS segments with carefully chosen base / limits. I do not
believe this is an issue in practice, but it is a kernel bug.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@osdl.org>
[ x86-64 had the same problem, and the same fix. Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commits
71db63acff
[PATCH] increase PCIBIOS_MIN_IO on x86
and
0b2bfb4e7f
ACPI: increase PCIBIOS_MIN_IO on x86
since Lukas Sandströ<lukass@etek.chalmers.se> reports that this breaks
his on-board nvidia audio.
We should re-visit this later. For now we revert the change
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In file included from linux-2.6.13-rc5/arch/i386/kernel/timers/timer_pit.c:20:
linux-2.6.13-rc5/include/asm-i386/mach-visws/do_timer.h: In function `do_timer_overflow':
linux-2.6.13-rc5/include/asm-i386/mach-visws/do_timer.h:32: error: `i8259A_lock' undeclared (first use in this function)
linux-2.6.13-rc5/include/asm-i386/mach-visws/do_timer.h:32: error: (Each undeclared identifier is reported only once
linux-2.6.13-rc5/include/asm-i386/mach-visws/do_timer.h:32: error: for each function it appears in.)
make[3]: *** [arch/i386/kernel/timers/timer_pit.o] Error 1
make[2]: *** [arch/i386/kernel/timers] Error 2
make[1]: *** [arch/i386/kernel] Error 2
make: *** [_all] Error 2
Signed-off-by: Tom Duffy <thomas.duffy.99@alumni.brown.edu>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a number of x86 laptops that have some non-PCI IO ports
in the 0x1000-0x1fff range, and it's quite hard to control the correct
order of resource allocation between PCI and other subsystems controlling
these ports. Especially with modular kernel.
So just increase PCIBIOS_MIN_IO to 0x4000 to prevent any new PCI
resource allocations in the problematic range (this limitation must
apply _only_ to the root bus resources - see Linus' change in
pci_bus_alloc_resource). As PCIBIOS_MIN_IO and PCIBIOS_MIN_CARDBUS_IO
are the same now on i386 and x86-64, we can remove the latter.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some edge problems with the original C rewrite.
Thanks go to Cal Peake, who pinpointed the breakage to the rewrite, and
tested this fixed version.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid using "rep scas", just let the compiler select a sequence of
regular instructions.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
include/asm/ptrace.h: In function `user_mode_vm':
include/asm/ptrace.h:67: `VM_MASK' undeclared (first use in this function)
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- make the new user_mode() return 0 or 1 (same as x86_64)
- remove conditional jump from user_mode_vm() it's called every timer
tick on each CPU on SMP)
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
set_cpus_allowed is not safe in interrupt context
and disabling apics is complicated code so don't
call machine_shutdown on i386 from emergency_restart().
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the kernel is working well and we want to restart cleanly
kernel_restart is the function to use. But in many instances
the kernel wants to reboot when thing are expected to be working
very badly such as from panic or a software watchdog handler.
This patch adds the function emergency_restart() so that
callers can be clear what semantics they expect when calling
restart. emergency_restart() is expected to be callable
from interrupt context and possibly reliable in even more
trying circumstances.
This is an initial generic implementation for all architectures.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This one ends up using an inline asm format that claims to read memory
and then clobber it (rather than just write it directly), which made it
easier to use the existing "alternative_input()" infrastructure support.
Now the fxsave code matches the fxrstor.
It's really just a single instruction, conditional on whether the CPU
supports FXSR or not, so implement it as such instead of making it a
function that queries FXSR dynamically.
This means that the instruction just gets automatically rewritten to the
correct one at boot-time.
inotify is intended to correct the deficiencies of dnotify, particularly
its inability to scale and its terrible user interface:
* dnotify requires the opening of one fd per each directory
that you intend to watch. This quickly results in too many
open files and pins removable media, preventing unmount.
* dnotify is directory-based. You only learn about changes to
directories. Sure, a change to a file in a directory affects
the directory, but you are then forced to keep a cache of
stat structures.
* dnotify's interface to user-space is awful. Signals?
inotify provides a more usable, simple, powerful solution to file change
notification:
* inotify's interface is a system call that returns a fd, not SIGIO.
You get a single fd, which is select()-able.
* inotify has an event that says "the filesystem that the item
you were watching is on was unmounted."
* inotify can watch directories or files.
Inotify is currently used by Beagle (a desktop search infrastructure),
Gamin (a FAM replacement), and other projects.
See Documentation/filesystems/inotify.txt.
Signed-off-by: Robert Love <rml@novell.com>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
http://bugme.osdl.org/show_bug.cgi?id=4016
Written-by: David Shaohua Li <shaohua.li@intel.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If CONFIG_NUMA isn't set, we use the define in <linux/mmzone.h> for
early_pfn_to_nid (which defines it to 0).
Because of this, the prototype needs to move inside the CONFIG_NUMA too, or
anal gcc's get really confused.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent cleanups to asm-i386/mmzone.h were suboptimal nesting an ifdef of
the same symbol. This patch removes some of the ifdef'ery to make things more
readable again.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There has been some discuss about solving the SMP MTRR suspend/resume
breakage, but I didn't find a patch for it. This is an intent for it. The
basic idea is moving mtrr initializing into cpu_identify for all APs (so it
works for cpu hotplug). For BP, restore_processor_state is responsible for
restoring MTRR.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove legacy ISA serial ports for Accent, Boca, Fourport, Hub6 and MCA
from the architecture specific serial.h include.
The only ports which remain in asm-*/serial.h are the platform specific
entries. These should really be converted by platform maintainers to
use a platform device, such as can be found in
arch/arm/mach-footbridge/isa.c
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With CONFIG_PCI=n:
In file included from include/linux/pci.h:917,
from lib/iomap.c:6:
include/asm/pci.h:104: warning: `enum pci_dma_burst_strategy' declared inside parameter list
include/asm/pci.h:104: warning: its scope is only this definition or declaration, which is probably not what you want.
include/asm/pci.h: In function `pci_dma_burst_advice':
include/asm/pci.h:106: dereferencing pointer to incomplete type
include/asm/pci.h:106: `PCI_DMA_BURST_INFINITY' undeclared (first use in this function)
include/asm/pci.h:106: (Each undeclared identifier is reported only once
include/asm/pci.h:106: for each function it appears in.)
make[1]: *** [lib/iomap.o] Error 1
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After seeing, at best, "guesses" as to the following kind
of information in several drivers, I decided that we really
need a way for platforms to specifically give advice in this
area for what works best with their PCI controller implementation.
Basically, this new interface gives DMA bursting advice on
PCI. There are three forms of the advice:
1) Burst as much as possible, it is not necessary to end bursts
on some particular boundary for best performance.
2) Burst on some byte count multiple. A DMA burst to some multiple of
number of bytes may be done, but it is important to end the burst
on an exact multiple for best performance.
The best example of this I am aware of are the PPC64 PCI
controllers, where if you end a burst mid-cacheline then
chip has to refetch the data and the IOMMU translations
which hurts performance a lot.
3) Burst on a single byte count multiple. Bursts shall end
exactly on the next multiple boundary for best performance.
Sparc64 and Alpha's PCI controllers operate this way. They
disconnect any device which tries to burst across a cacheline
boundary.
Actually, newer sparc64 PCI controllers do not have this behavior.
That is why the "pdev" is passed into the interface, so I can
add code later to check which PCI controller the system is using
and give advice accordingly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Old ISA/VESA systems sometimes put tertiary IDE controllers at addresses
0x1e8, 0x168, 0x1e0 or 0x160. Linux thus probes these addresses on x86
systems. Unfortunately some PCI systems now use these addresses for other
purposes which leads to users seeing minute plus hangs during boot or even
crashes.
The following patch (again has been in Fedora for a while) only probes the
obscure legacy ISA ports on machinea that are pre-PCI. This seems to keep
everyone happy and if there is someone with that utterly weird corner case
the ide= command line still provides a get out of jail card.
Unsurprisingly we've not found anyone so affected.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I believe at least for seccomp it's worth to turn off the tsc, not just for
HT but for the L2 cache too. So it's up to you, either you turn it off
completely (which isn't very nice IMHO) or I recommend to apply this below
patch.
This has been tested successfully on x86-64 against current cogito
repository (i686 compiles so I didn't bother testing ;). People selling
the cpu through cpushare may appreciate this bit for a peace of mind.
There's no way to get any timing info anymore with this applied
(gettimeofday is forbidden of course). The seccomp environment is
completely deterministic so it can't be allowed to get timing info, it has
to be deterministic so in the future I can enable a computing mode that
does a parallel computing for each task with server side transparent
checkpointing and verification that the output is the same from all the 2/3
seller computers for each task, without the buyer even noticing (for now
the verification is left to the buyer client side and there's no
checkpointing, since that would require more kernel changes to track the
dirty bits but it'll be easy to extend once the basic mode is finished).
Eliminating a cold-cache read of the cr4 global variable will save one
cacheline during the tlb flush while making the code per-cpu-safe at the
same time. Thanks to Mikael Pettersson for noticing the tlb flush wasn't
per-cpu-safe.
The global tlb flush can run from irq (IPI calling do_flush_tlb_all) but
it'll be transparent to the switch_to code since the IPI won't make any
change to the cr4 contents from the point of view of the interrupted code
and since it's now all per-cpu stuff, it will not race. So no need to
disable irqs in switch_to slow path.
Signed-off-by: Andrea Arcangeli <andrea@cpushare.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the CFQ io scheduler to the new time sliced design (cfq
v3). It provides full process fairness, while giving excellent
aggregate system throughput even for many competing processes. It
supports io priorities, either inherited from the cpu nice value or set
directly with the ioprio_get/set syscalls. The latter closely mimic
set/getpriority.
This import is based on my latest from -mm.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch provides the interfaces necessary to read the dump contents,
treating it as a high memory device.
Signed off by Hariprasad Nellitheertha <hari@in.ibm.com>
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch exports kexec global variable "crash_notes" to user space
through sysfs as kernel attribute in /sys/kernel.
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the i386 implementation of kexec.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For one kernel to report a crash another kernel has created we need
to have 2 kernels loaded simultaneously in memory. To accomplish this
the two kernels need to built to run at different physical addresses.
This patch adds the CONFIG_PHYSICAL_START option to the x86 kernel
so we can do just that. You need to know what you are doing and
the ramifications are before changing this value, and most users
won't care so I have made it depend on CONFIG_EMBEDDED
bzImage kernels will work and run at a different address when compiled
with this option but they will still load at 1MB. If you need a kernel
loaded at a different address as well you need to boot a vmlinux.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When coming out of apic mode attempt to set the appropriate
apic back into virtual wire mode. This improves on previous versions
of this patch by by never setting bot the local apic and the ioapic
into veritual wire mode.
This code looks at data from the mptable to see if an ioapic has
an ExtInt input to make this decision. A future improvement
is to figure out which apic or ioapic was in virtual wire mode
at boot time and to remember it. That is potentially a more accurate
method, of selecting which apic to place in virutal wire mode.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Maciej W. Rozycki" <macro@linux-mips.org>
Fix a kexec problem whcih causes local APIC detection failure.
The problem is detect_init_APIC() is called early, before the command line
have been processed. Therefore "lapic" (and "nolapic") have not been seen,
yet.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Maciej W. Rozycki" <macro@linux-mips.org>
Rename APIC_MODE_EXINT to APIC_MODE_EXTINT - I think it should be named
after what the mode is called in documentation.
From: "Eric W. Biederman" <ebiederm@lnxi.com>
I have reduced this patch to just the name change in the header. And
integrated the changes into the patches that add those
lines. Otherwise I ran into some ugly dependencies.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do some basic initial tuning.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the very aggressive idle stuff that has recently gone into 2.6 - it is
going against the direction we are trying to go. Hopefully we can regain
performance through other methods.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do CPU load averaging over a number of different intervals. Allow each
interval to be chosen by sending a parameter to source_load and target_load.
0 is instantaneous, idx > 0 returns a decaying average with the most recent
sample weighted at 2^(idx-1). To a maximum of 3 (could be easily increased).
So generally a higher number will result in more conservative balancing.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2.6.12-rc6-mm1 has a few remaining synchronize_kernel()s, some (but not
all) in comments. This patch changes these synchronize_kernel() calls (and
comments) to synchronize_rcu() or synchronize_sched() as follows:
- arch/x86_64/kernel/mce.c mce_read(): change to synchronize_sched() to
handle races with machine-check exceptions (synchronize_rcu() would not cut
it given RCU implementations intended for hardcore realtime use.
- drivers/input/serio/i8042.c i8042_stop(): change to synchronize_sched() to
handle races with i8042_interrupt() interrupt handler. Again,
synchronize_rcu() would not cut it given RCU implementations intended for
hardcore realtime use.
- include/*/kdebug.h comments: change to synchronize_sched() to handle races
with NMIs. As before, synchronize_rcu() would not cut it...
- include/linux/list.h comment: change to synchronize_rcu(), since this
comment is for list_del_rcu().
- security/keys/key.c unregister_key_type(): change to synchronize_rcu(),
since this is interacting with RCU read side.
- security/keys/process_keys.c install_session_keyring(): change to
synchronize_rcu(), since this is interacting with RCU read side.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I really wish smp_prepare_cpu() would disappear eventually. In the interim
this is ideally a weak function, so we dont end up changing several places
to define this dummy in headers.
Today since the dummy declaration is done only in drivers/base/cpu.c but
the function is called in kernel/power/smp.c i get undefined reference in
my cpu hotplug code for x86_64 under development.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean CPU states in order to reuse smp boot code for CPU hotplug.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make SEP init per-cpu, so it is hotplug safe.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces a startup parameter no_broadcast. When we enable
CONFIG_HOTPLUG_CPU, we dont want to use broadcast shortcut as it has ill
effects on a offline cpu. If we issue broadcast, the IPI is also delivered
to offline cpus, or partially up cpu causing stale IPI's to be handled,
which is a problem and can cause undesirable effects.
Introduces a new startup cmdline option no_ipi_broadcast, that can be
switched at cmdline if necessary.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(The i386 CPU hotplug patch provides infrastructure for some work which Pavel
is doing as well as for ACPI S3 (suspend-to-RAM) work which Li Shaohua
<shaohua.li@intel.com> is doing)
The following provides i386 architecture support for safely unregistering and
registering processors during runtime, updated for the current -mm tree. In
order to avoid dumping cpu hotplug code into kernel/irq/* i dropped the
cpu_online check in do_IRQ() by modifying fixup_irqs(). The difference being
that on cpu offline, fixup_irqs() is called before we clear the cpu from
cpu_online_map and a long delay in order to ensure that we never have any
queued external interrupts on the APICs. There are additional changes to s390
and ppc64 to account for this change.
1) Add CONFIG_HOTPLUG_CPU
2) disable local APIC timer on dead cpus.
3) Disable preempt around irq balancing to prevent CPUs going down.
4) Print irq stats for all possible cpus.
5) Debugging check for interrupts on offline cpus.
6) Hacky fixup_irqs() to redirect irqs when cpus go off/online.
7) play_dead() for offline cpus to spin inside.
8) Handle offline cpus set in flush_tlb_others().
9) Grab lock earlier in smp_call_function() to prevent CPUs going down.
10) Implement __cpu_disable() and __cpu_die().
11) Enable local interrupts in cpu_enable() after fixup_irqs()
12) Don't fiddle with NMI on dead cpu, but leave intact on other cpus.
13) Program IRQ affinity whilst cpu is still in cpu_online_map on offline.
Signed-off-by: Zwane Mwaikambo <zwane@linuxpower.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They don't actually clobber memory, but gcc doesn't even know they
_read_ memory, so can apparently re-order memory accesses around them.
Which obviously does the wrong thing if the memory access happens to
change the memory that the compare function is accessing..
Verified to fix a strange boot problem by Jens Axboe.
This patch adds function-return probes to kprobes for the i386
architecture. This enables you to establish a handler to be run when a
function returns.
1. API
Two new functions are added to kprobes:
int register_kretprobe(struct kretprobe *rp);
void unregister_kretprobe(struct kretprobe *rp);
2. Registration and unregistration
2.1 Register
To register a function-return probe, the user populates the following
fields in a kretprobe object and calls register_kretprobe() with the
kretprobe address as an argument:
kp.addr - the function's address
handler - this function is run after the ret instruction executes, but
before control returns to the return address in the caller.
maxactive - The maximum number of instances of the probed function that
can be active concurrently. For example, if the function is non-
recursive and is called with a spinlock or mutex held, maxactive = 1
should be enough. If the function is non-recursive and can never
relinquish the CPU (e.g., via a semaphore or preemption), NR_CPUS should
be enough. maxactive is used to determine how many kretprobe_instance
objects to allocate for this particular probed function. If maxactive <=
0, it is set to a default value (if CONFIG_PREEMPT maxactive=max(10, 2 *
NR_CPUS) else maxactive=NR_CPUS)
For example:
struct kretprobe rp;
rp.kp.addr = /* entrypoint address */
rp.handler = /*return probe handler */
rp.maxactive = /* e.g., 1 or NR_CPUS or 0, see the above explanation */
register_kretprobe(&rp);
The following field may also be of interest:
nmissed - Initialized to zero when the function-return probe is
registered, and incremented every time the probed function is entered but
there is no kretprobe_instance object available for establishing the
function-return probe (i.e., because maxactive was set too low).
2.2 Unregister
To unregiter a function-return probe, the user calls
unregister_kretprobe() with the same kretprobe object as registered
previously. If a probed function is running when the return probe is
unregistered, the function will return as expected, but the handler won't
be run.
3. Limitations
3.1 This patch supports only the i386 architecture, but patches for
x86_64 and ppc64 are anticipated soon.
3.2 Return probes operates by replacing the return address in the stack
(or in a known register, such as the lr register for ppc). This may
cause __builtin_return_address(0), when invoked from the return-probed
function, to return the address of the return-probes trampoline.
3.3 This implementation uses the "Multiprobes at an address" feature in
2.6.12-rc3-mm3.
3.4 Due to a limitation in multi-probes, you cannot currently establish
a return probe and a jprobe on the same function. A patch to remove
this limitation is being tested.
This feature is required by SystemTap (http://sourceware.org/systemtap),
and reflects ideas contributed by several SystemTap developers, including
Will Cohen and Ananth Mavinakayanahalli.
Signed-off-by: Hien Nguyen <hien@us.ibm.com>
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@laposte.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The preempt_count member of struct thread_info is currently either defined
as int, unsigned int or __s32 depending on arch. This patch makes the type
of preempt_count an int on all archs.
Having preempt_count be an unsigned type prevents the catching of
preempt_count < 0 bugs, and using int on some archs and __s32 on others is
not exactely "neat" - much nicer when it's just int all over.
A previous version of this patch was already ACK'ed by Robert Love, and the
only change in this version of the patch compared to the one he ACK'ed is
that this one also makes sure the preempt_count member is consistently
commented.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename user_mode to user_mode_vm and add a user_mode macro similar to the
x86-64 one.
This is useful for Xen because the linux xen kernel does not runs on the same
priviledge that a vanilla linux kernel, and with this we just need to redefine
user_mode().
Signed-off-by: Vincent Hanquez <vincent.hanquez@cl.cam.ac.uk>
Cc: Ian Pratt <m+Ian.Pratt@cl.cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add 2 macros to set and get debugreg on x86. This is useful for Xen because
it will need only to redefine each macro to a hypervisor call.
Signed-off-by: Vincent Hanquez <vincent.hanquez@cl.cam.ac.uk>
Cc: Ian Pratt <m+Ian.Pratt@cl.cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86_64's cpu_khz is unsigned int and there is no reason why x86 needs to use
unsigned long.
So make cpu_khz unsigned int on x86 as well.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
csum_and_copy_to_user is static inline and uses VERIFY_WRITE. Patch allows
to remove asm/uaccess.h from i386_ksyms.c without dependency surprises.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the timer frequency selectable. The timer interrupt may cause bus
and memory contention in large NUMA systems since the interrupt occurs
on each processor HZ times per second.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is per Andi's request to remove NO_IOAPIC_CHECK from genapic and
use heuristics to prevent unique I/O APIC ID check for systems that don't
need it. The patch disables unique I/O APIC ID check for Xeon-based and
other platforms that don't use serial APIC bus for interrupt delivery.
Andi stated that AMD systems don't need unique IO_APIC_IDs either.
Signed-off-by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define pcibus_to_node to be able to figure out which NUMA node contains a
given PCI device. This defines pcibus_to_node(bus) in
include/linux/topology.h and adjusts the macros for i386 and x86_64 that
already provided a way to determine the cpumask of a pci device.
x86_64 was changed to not build an array of cpumasks anymore. Instead an
array of nodes is build which can be used to generate the cpumask via
node_to_cpumask.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Issue:
Current tsc based delay_calibration can result in significant errors in
loops_per_jiffy count when the platform events like SMIs
(System Management Interrupts that are non-maskable) are present. This could
lead to potential kernel panic(). This issue is becoming more visible with 2.6
kernel (as default HZ is 1000) and on platforms with higher SMI handling
latencies. During the boot time, SMIs are mostly used by BIOS (for things
like legacy keyboard emulation).
Description:
The psuedocode for current delay calibration with tsc based delay looks like
(0) Estimate a value for loops_per_jiffy
(1) While (loops_per_jiffy estimate is accurate enough)
(2) wait for jiffy transition (jiffy1)
(3) Note down current tsc (tsc1)
(4) loop until tsc becomes tsc1 + loops_per_jiffy
(5) check whether jiffy changed since jiffy1 or not and refine
loops_per_jiffy estimate
Consider the following cases
Case 1:
If SMIs happen between (2) and (3) above, we can end up with a
loops_per_jiffy value that is too low. This results in shorted delays and
kernel can panic () during boot (Mostly at IOAPIC timer initialization
timer_irq_works() as we don't have enough timer interrupts in a specified
interval).
Case 2:
If SMIs happen between (3) and (4) above, then we can end up with a
loops_per_jiffy value that is too high. And with current i386 code, too
high lpj value (greater than 17M) can result in a overflow in
delay.c:__const_udelay() again resulting in shorter delay and panic().
Solution:
The patch below makes the calibration routine aware of asynchronous events
like SMIs. We increase the delay calibration time and also identify any
significant errors (greater than 12.5%) in the calibration and notify it to
user.
Patch below changes both i386 and x86-64 architectures to use this
new and improved calibrate_delay_direct() routine.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide the architecture specific implementation for SPARSEMEM for i386 SMP
and NUMA systems.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide a default implementation for early_pfn_to_nid returning node 0. Allow
architectures to override this with their own implementation out of
asm/mmzone.h.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
discontig.c has some assumptions that mem_map[]s inside of a node are
contiguous. Teach it to make sure that each region that it's bringing online
is actually made up of valid ranges of ram.
Written-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch effectively eliminates direct use of pgdat->node_mem_map outside
of the DISCONTIG code. On a flat memory system, these fields aren't
currently used, neither are they on a sparsemem system.
There was also a node_mem_map(nid) macro on many architectures. Its use
along with the use of ->node_mem_map itself was not consistent. It has
been removed in favor of two new, more explicit, arch-independent macros:
pgdat_page_nr(pgdat, pagenr)
nid_page_nr(nid, pagenr)
I called them "pgdat" and "nid" because we overload the term "node" to mean
"NUMA node", "DISCONTIG node" or "pg_data_t" in very confusing ways. I
believe the newer names are much clearer.
These macros can be overridden in the sparsemem case with a theoretically
slower operation using node_start_pfn and pfn_to_page(), instead. We could
make this the only behavior if people want, but I don't want to change too
much at once. One thing at a time.
This patch removes more code than it adds.
Compile tested on alpha, alpha discontig, arm, arm-discontig, i386, i386
generic, NUMAQ, Summit, ppc64, ppc64 discontig, and x86_64. Full list
here: http://sr71.net/patches/2.6.12/2.6.12-rc1-mhp2/configs/
Boot tested on NUMAQ, x86 SMP and ppc64 power4/5 LPARs.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Martin J. Bligh <mbligh@aracnet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A lot of the code in arch/*/mm/hugetlbpage.c is quite similar. This patch
attempts to consolidate a lot of the code across the arch's, putting the
combined version in mm/hugetlb.c. There are a couple of uglyish hacks in
order to covert all the hugepage archs, but the result is a very large
reduction in the total amount of code. It also means things like hugepage
lazy allocation could be implemented in one place, instead of six.
Tested, at least a little, on ppc64, i386 and x86_64.
Notes:
- this patch changes the meaning of set_huge_pte() to be more
analagous to set_pte()
- does SH4 need s special huge_ptep_get_and_clear()??
Acked-by: William Lee Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the core of the (much simplified) early reclaim. The goal of this
patch is to reclaim some easily-freed pages from a zone before falling back
onto another zone.
One of the major uses of this is NUMA machines. With the default allocator
behavior the allocator would look for memory in another zone, which might be
off-node, before trying to reclaim from the current zone.
This adds a zone tuneable to enable early zone reclaim. It is selected on a
per-zone basis and is turned on/off via syscall.
Adding some extra throttling on the reclaim was also required (patch
4/4). Without the machine would grind to a crawl when doing a "make -j"
kernel build. Even with this patch the System Time is higher on
average, but it seems tolerable. Here are some numbers for kernbench
runs on a 2-node, 4cpu, 8Gig RAM Altix in the "make -j" run:
wall user sys %cpu ctx sw. sleeps
---- ---- --- ---- ------ ------
No patch 1009 1384 847 258 298170 504402
w/patch, no reclaim 880 1376 667 288 254064 396745
w/patch & reclaim 1079 1385 926 252 291625 548873
These numbers are the average of 2 runs of 3 "make -j" runs done right
after system boot. Run-to-run variability for "make -j" is huge, so
these numbers aren't terribly useful except to seee that with reclaim
the benchmark still finishes in a reasonable amount of time.
I also looked at the NUMA hit/miss stats for the "make -j" runs and the
reclaim doesn't make any difference when the machine is thrashing away.
Doing a "make -j8" on a single node that is filled with page cache pages
takes 700 seconds with reclaim turned on and 735 seconds without reclaim
(due to remote memory accesses).
The simple zone_reclaim syscall program is at
http://www.bork.org/~mort/sgi/zone_reclaim.c
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements a number of smp_processor_id() cleanup ideas that
Arjan van de Ven and I came up with.
The previous __smp_processor_id/_smp_processor_id/smp_processor_id API
spaghetti was hard to follow both on the implementational and on the
usage side.
Some of the complexity arose from picking wrong names, some of the
complexity comes from the fact that not all architectures defined
__smp_processor_id.
In the new code, there are two externally visible symbols:
- smp_processor_id(): debug variant.
- raw_smp_processor_id(): nondebug variant. Replaces all existing
uses of _smp_processor_id() and __smp_processor_id(). Defined
by every SMP architecture in include/asm-*/smp.h.
There is one new internal symbol, dependent on DEBUG_PREEMPT:
- debug_smp_processor_id(): internal debug variant, mapped to
smp_processor_id().
Also, i moved debug_smp_processor_id() from lib/kernel_lock.c into a new
lib/smp_processor_id.c file. All related comments got updated and/or
clarified.
I have build/boot tested the following 8 .config combinations on x86:
{SMP,UP} x {PREEMPT,!PREEMPT} x {DEBUG_PREEMPT,!DEBUG_PREEMPT}
I have also build/boot tested x64 on UP/PREEMPT/DEBUG_PREEMPT. (Other
architectures are untested, but should work just fine.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In file included from arch/i386/kernel/smp.c:235:
include/asm-i386/mach-numaq/mach_ipi.h:4: warning: `send_IPI_mask_sequence'
declared inline after its definition
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When Linux is running on the Xen virtual machine monitor, physical
addresses are virtualised and cannot be directly referenced by the AGP
GART. This patch fixes the GART driver for Xen by adding a layer of
abstraction between physical addresses and 'GART addresses'.
Architecture-specific functions are also defined for allocating and freeing
the GATT. Xen requires this to ensure that table really is contiguous from
the point of view of the GART.
These extra interface functions are defined as 'no-ops' for all existing
architectures that use the GART driver.
Signed-off-by: Keir Fraser <keir@xensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Some cpufreq drivers (at that time, only powernow-k7) need to recalibrate the
cpu_khz at runtime.
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
We fixed this bug before, but it didn't take. It may have been the case
that the problem was first noticed to occur in a CONFIG_REGPARM compile.
But it's not regparm functions that need not to make tail calls, it's
asmlinkage functions called with a user pt_regs frame on the stack
supplying their arguments. prevent_tail_call probably doesn't do anything
at all in regparm functions (your argument registers are going to be
clobbered, period). It was a braino to conditionalize that definition in
the first place.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Changed Name/defines from "Geode GX" to "Geode GX1" for clarification
- Dropped "-march=i586" in favor of "-march=i486"
- Dopped X86_OOSTORE support for Geode GX1
Signed-off-by: Kianusch Sayah Karadji <kianusch@sk-tech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes some needlessly global identifiers static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Arjan van de Ven <arjanv@infradead.org>
Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
New file - asm-generic/signal.h. Contains declarations of
__sighandler_t, __sigrestore_t, SIG_DFL, SIG_IGN, SIG_ERR and default
definitions of SIG_BLOCK, SIG_UNBLOCK and SIG_SETMASK.
asm-*/signal.h switched to including it. The only exception is
asm-parisc/signal.h that wants its own declaration of __sighandler_t;
that one is left as-is.
asm-ppc64/signal.h required one more thing - unlike everybody else it
used __sigrestorer_t instead of usual __sigrestore_t. PPC64 switched to
common spelling.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There were still a few comments left refering to verify_area, and two
functions, verify_area_skas & verify_area_tt that just wrap corresponding
access_ok_skas & access_ok_tt functions, just like verify_area does for
access_ok - deprecate those.
There was also a few places that still used verify_area in commented-out
code, fix those up to use access_ok.
After applying this one there should not be anything left but finally
removing verify_area completely, which will happen after a kernel release
or two.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch moves the IRQ-related SA_xxx flags (namely, SA_PROBE,
SA_SAMPLE_RANDOM and SA_SHIRQ) from all the arch-specific headers to
linux/signal.h. This looks like a left-over after the irq-handling code
was consolidated. The code was moved to kernel/irq/*, but the flags are
still left per-arch.
Right now, adding a new IRQ flag to the arch-specific header, like this
patch does:
http://cvs.sourceforge.net/viewcvs.py/*checkout*/alsa/alsa-driver/utils/patches/pcsp-kernel-2.6.10-03.diff?rev=1.1
no longer works, it breaks the compilation for all other arches, unless you
add that flag to all the other arch-specific headers too. So I think such
a clean-up makes sense.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch eliminates all kernel BUGs, trims about 35k off the typical
kernel, and makes the system slightly faster.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The specifications that talk about E820 map doesn't have an upper limit on
the number of e820 entries. But, today's kernel has a hard limit of 32.
With increase in memory size, we are seeing the number of E820 entries
reaching close to 32. Patch below bumps the number upto 128.
The patch changes the location of EDDBUF in zero-page (as it comes after E820).
As, EDDBUF is not used by boot loaders, this patch should not have any effect
on bootloader-setup code interface.
Patch covers both i386 and x86-64.
Tested on:
* grub booting bzImage
* lilo booting bzImage with EDID info enabled
* pxeboot of bzImage
Side-effect:
bss increases by ~ 2K and init.data increases by ~7.5K
on all systems, due to increase in size of static arrays.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the i386 HPET code assumes the entire HPET implementation from
the spec is present. This breaks on boxes that do not implement the
optional legacy timer replacement functionality portion of the spec.
This patch, which is very similar to my x86-64 patch for the same issue,
fixes the problem allowing i386 systems that cannot use the HPET for the
timer interrupt and RTC to still use the HPET as a time source. I've
tested this patch on a system systems without HPET, with HPET but without
legacy timer replacement, as well as HPET with legacy timer replacement.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent support for K8 multicore was misported from x86-64 to i386, due
to an unnecessary inconsistency between the CPUID code. Sure, there is are
no x86-64 VIA chips yet, but it should happen eventually.
This patch fixes the i386 bug as well as makes x86-64 match i386 in the
handing of the CPUID array.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bug against an xSeries system showed up recently noting that the
check_nmi_watchdog() test was failing.
I have been investigating it and discovered in both i386 and x86_64 the
recent change to the routine to use the cpu_callin_map has uncovered a
problem. Prior to that change, on an SMP box, the test was trivally
passing because all cpu's were found to not yet be online, but now with the
callin_map they are discovered, it goes on to test the counter and they
have not yet begun to increment, so it announces a CPU is stuck and bails
out.
On all the systems I have access to test, the announcement of failure is
also bougs... by the time you can login and check /proc/interrupts, the
NMI count is happily incrementing on all CPUs. Its just that the test is
being done too early.
I have tried moving the call to the test around a bit, and it was always
too early. I finally hit on this proposed solution, it delays the routine
via a late_initcall(), seems like the right solution to me.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new i386/x86_64 assemblers no longer accept instructions for moving
between a segment register and a 32bit memory location, i.e.,
movl (%eax),%ds
movl %ds,(%eax)
To generate instructions for moving between a segment register and a
16bit memory location without the 16bit operand size prefix, 0x66,
mov (%eax),%ds
mov %ds,(%eax)
should be used. It will work with both new and old assemblers. The
assembler starting from 2.16.90.0.1 will also support
movw (%eax),%ds
movw %ds,(%eax)
without the 0x66 prefix. I am enclosing patches for 2.4 and 2.6 kernels
here. The resulting kernel binaries should be unchanged as before, with
old and new assemblers, if gcc never generates memory access for
unsigned gsindex;
asm volatile("movl %%gs,%0" : "=g" (gsindex));
If gcc does generate memory access for the code above, the upper bits
in gsindex are undefined and the new assembler doesn't allow it.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace misleading definition of FIRST_USER_PGD_NR 0 by definition of
FIRST_USER_ADDRESS 0 in all the MMU architectures beyond arm and arm26.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Appended patch adds the support for Intel dual-core detection and displaying
the core related information in /proc/cpuinfo.
It adds two new fields "core id" and "cpu cores" to x86 /proc/cpuinfo and the
"core id" field for x86_64("cpu cores" field is already present in x86_64).
Number of processor cores in a die is detected using cpuid(4) and this is
documented in IA-32 Intel Architecture Software Developer's Manual (vol 2a)
(http://developer.intel.com/design/pentium4/manuals/index_new.htm#sdm_vol2a)
This patch also adds cpu_core_map similar to cpu_sibling_map.
Slightly hacked by AK.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This moves the macro loaddebug from asm-i386/suspend.h to
asm-i386/processor.h, which is the place that makes sense for it to be
defined, removes the extra copy of the same macro in
arch/i386/kernel/process.c, and makes arch/i386/kernel/signal.c use the
macro in place of its expansion.
This is a purely cosmetic cleanup for the normal i386 kernel. However, it
is handy for Xen to be able to just redefine the loaddebug macro once
instead of also changing the signal.c code.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
