Add xtal as a configuration parameter so it can be used
in the IF register value calculation.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1) This is not allowed by the kernel coding style
2) Just configure your editor correctly
3) It's really ugly
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
According with Malcolm, the missing breaks are intentional.
So, let's revert commit d442b15fb4,
add some comments to document it and fix the two smatch warnings:
drivers/media/usb/dvb-usb-v2/lmedm04.c:828 lme_firmware_switch() warn: missing break? reassigning 'st->dvb_usb_lme2510_firmware'
drivers/media/usb/dvb-usb-v2/lmedm04.c:850 lme_firmware_switch() warn: missing break? reassigning 'st->dvb_usb_lme2510_firmware'
using a different strategy to avoid reassign values to
st->dvb_usb_lme2510_firmware.
Acked-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When new parameters are added for si2168 driver, the parameters have to be explicitly defined for each device if the
si2168_config struct is not initialized to all zeros.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Load SDR sub-driver in order to support SDR for devices having
this tuner too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
That logic was duplicated from rtl2832_sdr.h in order to avoid hard
dependency for staging directory. rtl2832_sdr is moved to media, so
we could remove that code now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Better to rename tuner I2C to something which clearly says it is
for tuner as there is now multiple different I2C clients used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is RTL2832P devices having extra MN88473 demodulator. This
patch add support for such configuration. Logically MN88473 slave
demodulator is connected to RTL2832 master demodulator, both I2C
bus and TS input. RTL2832 is integrated to RTL2832U and RTL2832P
chips. Chip version RTL2832P has extra TS interface for connecting
slave demodulator.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is RTL2832P devices having extra MN88472 demodulator. This
patch add support for such configuration. Logically MN88472 slave
demodulator is connected to RTL2832 master demodulator, both I2C
bus and TS input. RTL2832 is integrated to RTL2832U and RTL2832P
chips. Chip version RTL2832P has extra TS interface for connecting
slave demodulator.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Enable integrated demod ADC only when demod is used. Keep integrated
demod ADC disabled when external demod is used. This fixes corrupted
stream in a case external demod was used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is wrong that sp2 device uses the i2c adapter from m88ds3103 return.
sp2 device sits on the same i2c bus with m88ds3103, not behind m88ds3103.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add an option to disable remote controller for DVBSky devices by specifying
the disable_rc option at modprobe.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
dev_err includes the function name in the log printout, so there is no need to include it manually. While here, fix a small grammatical error in the i2c error message.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dvb-usb-v2 already prints out the MAC address, no need to print
it out also here.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure that loaded modules are const char strings so we don't
load arbitrary modules in the future, nor allow for format string
leaks in the module request call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure that loaded modules are const char strings so we don't
load arbitrary modules in the future, nor allow for format string
leaks in the module request call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for IT930x USB bridge and IT9303 reference design.
It is a DVB-T/T2/C tuner with the following components:
- IT9303 USB bridge
- Si2168-B40 demodulator
- Si2147-A30 tuner
The IT9303 requires firmware that can be downloaded here:
http://trsqr.net/olli/linux/firmwares/it930x/
The Si2168-B40 requires firmware, but the one that is used by PCTV 292e can be used.
http://palosaari.fi/linux/v4l-dvb/firmware/Si2168/Si2168-B40/
The Si2147-A30 tuner does not require firmware loading.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some I2C tuner drivers require that the I2C device of the tuner is added
to the I2C adapter of the demodulator (Si2168+Si2157 for example). Add
possibility to tell af9035_add_i2c_dev which I2C adapter should be used.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support for DVBSky dvb-s2 usb: add dvb-usb-v2 driver for DVBSky dvb-s2
box, no ci support yet.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Used tda18212 tuner is implemented as I2C driver. Implement I2C
client to anysee and use it for tda18212.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It crash kernel when device was removed while it was streaming.
That is because we removed driver and frontend thread was still
running. Use new callback which allows I2C driver removal just
after frontend is unregistered.
V2: fixed by reported by Daniel
Reported-by: Daniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add tuner_detach callback in order to allow custom detach. It is
needed when tuner driver is implemented I2C client or some other
kernel bus, but not proprietary dvb_attach / dvb_detach.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add frontend_detach callback in order to allow custom detach. It is
needed when demod driver is implemented I2C client or some other
kernel bus, but not proprietary dvb_attach / dvb_detach.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I2C driver address is passed as a i2c_new_device() parameter when
device is created. Thus no need to keep it in config struct.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Biggest problem of that function is complexity. Try reduce complexity:
* define macros to detect all 3 supported xfers
* remove duplicate message maximum size checks
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Re-implement sleep. Based USB sniffs taken from the latest Hauppauge
windows driver version 07/10/2014, 14.6.23.32191.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change the it913x driver to use the I2C high lever tuner
binding model. As af9035 depends on it, add a code there
to do the binding.
[mchehab@osg.samsung.com: Merge 3 patches into one, because
we don't want to break bisect due to the conversion]
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove tuner_ prefix from module name and file names. Prefix was
added due to file name conflict on media out-tree build system.
Demodulator having same name does not exists anymore. So lets
remove dumb prefix.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reverts commit 3ab2512337
[media] af9035: override tuner for AVerMedia A835B devices
Original commit itself is correct, but it was replaced by more
general solution (commit 1cbbf90d04).
This old solution was committed by a accident and is not needed
anymore.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Integrated RF tuner of IT9135 is connected to demod clock source
named dyn0_clk. Enable that clock source in order to provide stable
clock early enough.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some patches that depends on media-v3.16-rc6.
So, merge back from upstream before applying them.
* linus/master: (1123 commits)
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
staging: vt6655: buffer overflow in ioctl
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
...
add the following IDs
USB_PID_PCTV_78E (0x025a) for PCTV 78e
USB_PID_PCTV_79E (0x0262) for PCTV 79e
For these it9135 devices.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:24:5: warning: symbol 'dvb_usbv2_disable_rc_polling' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/dvb-usb-v2/mxl111sf.c:34:5: warning: symbol 'dvb_usb_mxl111sf_isoc' was not declared. Should it be static?
drivers/media/usb/dvb-usb-v2/mxl111sf.c:38:5: warning: symbol 'dvb_usb_mxl111sf_spi' was not declared. Should it be static?
drivers/media/usb/dvb-usb-v2/mxl111sf.c:46:5: warning: symbol 'dvb_usb_mxl111sf_rfswitch' was not declared. Should it be static?
drivers/media/usb/dvb-usb-v2/mxl111sf.c:890:22: warning: symbol 'mxl111sf_i2c_algo' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reported by Dan Carpenter:
The patch d10d1b9ac9: "[media] dvb_usb_v2: use dev_* logging
macros" from Jun 26, 2012, leads to the following Smatch complaint:
drivers/media/usb/dvb-usb-v2/dvb_usb_urb.c:31 dvb_usb_v2_generic_io()
error: we previously assumed 'd' could be null (see line 29)
...
Remove whole check as it must not happen in any case. Driver is
totally broken if it does not have valid pointer to device.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Normally, ADAP_STREAMING bit is set in dvb_usb_start_feed and cleared in
dvb_usb_stop_feed.
But in exceptional cases, for example, when the tv is playing programs
and the tuner is pulled out, then dvb_usbv2_disconnect is called.
In such case, it will first call dvb_usbv2_adapter_frontend_exit to stop
dvb_frontend_thread, and then call dvb_usbv2_adapter_dvb_exit to clear
ADAP_STREAMING bit.
At this point, if dvb_frontend_thread is sleeping and waiting for
ADAP_STREAMING to be cleared to get out of sleep. then
dvb_frontend_thread can never be stoped, because clearing ADAP_STREAMING
bit is performed after dvb_frontend_thread is stopped (i.e. performed in
dvb_usbv2_adapter_dvb_exit).
So, deadlock:
[ 240.822037] INFO: task khubd:497 blocked for more than 120 seconds.
[ 240.822655] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.830493] khubd D c0013b3c 0 497 2 0x00000000
[ 240.836996] [<c0013b3c>] (__schedule+0x200/0x54c) from [<c00110f4>] (schedule_timeout+0x14c/0x19c)
[ 240.845940] [<c00110f4>] (schedule_timeout+0x14c/0x19c) from [<c00137f4>] (wait_for_common+0xac/0x150)
[ 240.855234] [<c00137f4>] (wait_for_common+0xac/0x150) from [<c004989c>] (kthread_stop+0x58/0x90)
[ 240.864004] [<c004989c>] (kthread_stop+0x58/0x90) from [<c03b2ebc>] (dvb_frontend_stop+0x3c/0x9c)
[ 240.872849] [<c03b2ebc>] (dvb_frontend_stop+0x3c/0x9c) from [<c03b2f3c>] (dvb_unregister_frontend+0x20/0xd8)
[ 240.882666] [<c03b2f3c>] (dvb_unregister_frontend+0x20/0xd8) from [<c03ed938>] (dvb_usbv2_exit+0x68/0xfc)
[ 240.892204] [<c03ed938>] (dvb_usbv2_exit+0x68/0xfc) from [<c03eda18>] (dvb_usbv2_disconnect+0x4c/0x70)
[ 240.901499] [<c03eda18>] (dvb_usbv2_disconnect+0x4c/0x70) from [<c031c050>] (usb_unbind_interface+0x58/0x188)
[ 240.911395] [<c031c050>] (usb_unbind_interface+0x58/0x188) from [<c02c3e78>] (__device_release_driver+0x74/0xd0)
[ 240.921544] [<c02c3e78>] (__device_release_driver+0x74/0xd0) from [<c02c3ef0>] (device_release_driver+0x1c/0x28)
[ 240.931697] [<c02c3ef0>] (device_release_driver+0x1c/0x28) from [<c02c39b8>] (bus_remove_device+0xc4/0xe4)
[ 240.941332] [<c02c39b8>] (bus_remove_device+0xc4/0xe4) from [<c02c1344>] (device_del+0xf4/0x178)
[ 240.950106] [<c02c1344>] (device_del+0xf4/0x178) from [<c0319eb0>] (usb_disable_device+0xa0/0x1c8)
[ 240.959040] [<c0319eb0>] (usb_disable_device+0xa0/0x1c8) from [<c03128b4>] (usb_disconnect+0x88/0x188)
[ 240.968326] [<c03128b4>] (usb_disconnect+0x88/0x188) from [<c0313edc>] (hub_thread+0x4d0/0x1200)
[ 240.977100] [<c0313edc>] (hub_thread+0x4d0/0x1200) from [<c0049690>] (kthread+0xa4/0xb0)
[ 240.985174] [<c0049690>] (kthread+0xa4/0xb0) from [<c0009118>] (ret_from_fork+0x14/0x3c)
[ 240.993259] INFO: task kdvb-ad-0-fe-0:3256 blocked for more than 120 seconds.
[ 241.000349] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 241.008162] kdvb-ad-0-fe-0 D c0013b3c 0 3256 2 0x00000000
[ 241.014507] [<c0013b3c>] (__schedule+0x200/0x54c) from [<c03eda44>] (wait_schedule+0x8/0x10)
[ 241.022924] [<c03eda44>] (wait_schedule+0x8/0x10) from [<c001120c>] (__wait_on_bit+0x74/0xb8)
[ 241.031434] [<c001120c>] (__wait_on_bit+0x74/0xb8) from [<c00112b8>] (out_of_line_wait_on_bit+0x68/0x70)
[ 241.040902] [<c00112b8>] (out_of_line_wait_on_bit+0x68/0x70) from [<c03e5e88>] (dvb_usb_fe_sleep+0xf4/0xfc)
[ 241.050618] [<c03e5e88>] (dvb_usb_fe_sleep+0xf4/0xfc) from [<c03b4b74>] (dvb_frontend_thread+0x124/0x4e8)
[ 241.060164] [<c03b4b74>] (dvb_frontend_thread+0x124/0x4e8) from [<c0049690>] (kthread+0xa4/0xb0)
[ 241.068929] [<c0049690>] (kthread+0xa4/0xb0) from [<c0009118>] (ret_from_fork+0x14/0x3c)
Fix it by calling dvb_usbv2_adapter_frontend_exit() latter.
Test enviroment: odroidx2 + Hauppauge(WinTV-Aero-M)
Signed-off-by: Changbing Xiong <cb.xiong@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
- removal of sn9c102. This device driver was replaced a long time ago
by gspca
- solo6x10 and go7007 webcam drivers moved from staging into
mainstream. They were waiting for an API to allow setting the image
detection matrix
- SDR drivers moved from staging into mainstream: sdr-msi3101 (renamed
as msi2500) and rtl2832
- added SDR driver for airspy
- added demux driver: si2165
- rework at several RC subsystem, making the code for RC-5 SZ variant
to be added at the standard RC5 decoder
- added decoder for the XMP IR protocol
- tuner driver moved from staging into mainstream: msi3101 (renamed as
msi001)
- added documentation for some additional SDR pixfmt
- some device tree bindings documented
- added support for exynos3250 at s5p-jpeg
- remove the obsolete, unmaintained and broken mx1_camera driver
- added support for remote controllers at au0828 driver
- added a RC driver: sunxi-cir
- several driver fixes, enhancements and cleanups.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (455 commits)
[media] cx23885: fix UNSET/TUNER_ABSENT confusion
[media] coda: fix build error by making reset control optional
[media] radio-miropcm20: fix sparse NULL pointer warning
[media] MAINTAINERS: Update go7007 pattern
[media] MAINTAINERS: Update solo6x10 patterns
[media] media: atmel-isi: add primary DT support
[media] media: atmel-isi: convert the pdata from pointer to structure
[media] media: atmel-isi: add v4l2 async probe support
[media] rcar_vin: add devicetree support
[media] media: pxa_camera device-tree support
[media] media: mt9m111: add device-tree suppport
[media] soc_camera: add support for dt binding soc_camera drivers
[media] media: soc_camera: pxa_camera documentation device-tree support
[media] media: mt9m111: add device-tree documentation
[media] s5p-mfc: remove unnecessary calling to function video_devdata()
[media] s5p-jpeg: add chroma subsampling adjustment for Exynos3250
[media] s5p-jpeg: Prevent erroneous downscaling for Exynos3250 SoC
[media] s5p-jpeg: Assure proper crop rectangle initialization
[media] s5p-jpeg: fix g_selection op
[media] s5p-jpeg: Adjust jpeg_bound_align_image to Exynos3250 needs
...
Tuner ID set into EEPROM is wrong, which causes driver to select
wrong tuner profile. That leads device non-working. Fix issue by
overriding known bad tuner IDs with suitable default value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added Sveon STV21 device based on Realtek RTL2832U and FC0013 tuner
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The basic API of rc-core used to be:
dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();
which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:
dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();
There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).
[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
MEDIA_SDR_SUPPORT and I2C_MUX are needed for rtl2832_sdr.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media fixes from Mauro Carvalho Chehab:
"A series of driver fixes:
- fix DVB-S tuning with tda1071
- fix tuner probe on af9035 when the device has a bad eeprom
- some fixes for the new si2168/2157 drivers
- one Kconfig build fix (for omap4iss)
- fixes at vpif error path
- don't lock saa7134 ioctl at driver's base core level, as it now
uses V4L2 and VB2 locking schema
- fix audio at hdpvr driver
- fix the aspect ratio at the digital timings table
- one new USB ID (at gspca_pac7302): Genius i-Look 317 webcam"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca_pac7302: Add new usb-id for Genius i-Look 317
[media] tda10071: fix returned symbol rate calculation
[media] tda10071: fix spec inversion reporting
[media] tda10071: add missing DVB-S2/PSK-8 FEC AUTO
[media] tda10071: force modulation to QPSK on DVB-S
[media] hdpvr: fix two audio bugs
[media] davinci: vpif: missing unlocks on error
[media] af9035: override tuner id when bad value set into eeprom
[media] saa7134: use unlocked_ioctl instead of ioctl
[media] media: v4l2-core: v4l2-dv-timings.c: Cleaning up code wrong value used in aspect ratio
[media] si2168: firmware download fix
[media] si2157: add one missing parenthesis
[media] si2168: add one missing parenthesis
[media] staging: tighten omap4iss dependencies
The current "wait_on_bit" interface requires an 'action'
function to be provided which does the actual waiting.
There are over 20 such functions, many of them identical.
Most cases can be satisfied by one of just two functions, one
which uses io_schedule() and one which just uses schedule().
So:
Rename wait_on_bit and wait_on_bit_lock to
wait_on_bit_action and wait_on_bit_lock_action
to make it explicit that they need an action function.
Introduce new wait_on_bit{,_lock} and wait_on_bit{,_lock}_io
which are *not* given an action function but implicitly use
a standard one.
The decision to error-out if a signal is pending is now made
based on the 'mode' argument rather than being encoded in the action
function.
All instances of the old wait_on_bit and wait_on_bit_lock which
can use the new version have been changed accordingly and their
action functions have been discarded.
wait_on_bit{_lock} does not return any specific error code in the
event of a signal so the caller must check for non-zero and
interpolate their own error code as appropriate.
The wait_on_bit() call in __fscache_wait_on_invalidate() was
ambiguous as it specified TASK_UNINTERRUPTIBLE but used
fscache_wait_bit_interruptible as an action function.
David Howells confirms this should be uniformly
"uninterruptible"
The main remaining user of wait_on_bit{,_lock}_action is NFS
which needs to use a freezer-aware schedule() call.
A comment in fs/gfs2/glock.c notes that having multiple 'action'
functions is useful as they display differently in the 'wchan'
field of 'ps'. (and /proc/$PID/wchan).
As the new bit_wait{,_io} functions are tagged "__sched", they
will not show up at all, but something higher in the stack. So
the distinction will still be visible, only with different
function names (gds2_glock_wait versus gfs2_glock_dq_wait in the
gfs2/glock.c case).
Since first version of this patch (against 3.15) two new action
functions appeared, on in NFS and one in CIFS. CIFS also now
uses an action function that makes the same freezer aware
schedule call as NFS.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: David Howells <dhowells@redhat.com> (fscache, keys)
Acked-by: Steven Whitehouse <swhiteho@redhat.com> (gfs2)
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steve French <sfrench@samba.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140707051603.28027.72349.stgit@notabene.brown
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tuner ID set into EEPROM is wrong in some cases, which causes driver
to select wrong tuner profile. That leads device non-working. Fix
issue by overriding known bad tuner IDs with suitable default value.
Thanks to MX-NET Telekomunikace s.r.o. for providing non-working
DTV stick, that I could fix the bug!
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change handling of signal_lock on rs2000. Use ibuf[2] to detect
lock as there is a longer wait for lock to appear in ibuf[6].
Remove last_key and key_timeout and use jiffies plus 60ms
to detect that streaming is still active.
If the current jiffies is time_after the interrupt urb overdue and
clear signal lock.
This results in far faster recovery of lock and streaming.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"This contains:
- a new frontend/tuner driver set for si2168 and sa2157
- Videobuf 2 core now supports DVB too
- A new gspca sub-driver (dtcs033)
- saa7134 is now converted to use videobuf2
- add support for 4K timings
- several other driver fixes and improvements
PS. This pull request is shorter than usual, partly because I have
some other patches on topic branches that I'll be sending you later
this week"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (286 commits)
[media] au0828-dvb: restore its permission to 644
[media] xc5000: delay tuner sleep to 5 seconds
[media] xc5000: Don't use whitespace before tabs
[media] xc5000: fix CamelCase
[media] xc5000: Don't wrap msleep()
[media] xc5000: get rid of positive error codes
[media] au0828: reset streaming when a new frequency is set
[media] au0828: Improve debug messages for urb_completion
[media] au0828: Cancel stream-restart operation if frontend is disconnected
[media] dib0700: fix RC support on Hauppauge Nova-TD
[media] USB: as102_usb_drv.c: Remove useless return variables
[media] v4l: Fix documentation of V4L2_PIX_FMT_H264_MVC and VP8 pixel formats
[media] m5mols: Replace missing header
[media] staging: lirc: Fix sparse warnings
[media] fix mceusb endpoint type identification/handling
[media] az6027: Added the PID for a new revision of the Elgato EyeTV Sat DVB-S Tuner
[media] DocBook media: fix typo
[media] adv7604: Add missing include to linux/types.h
[media] v4l: Validate fields in the core code for subdev EDID ioctls
[media] v4l: Add support for DV timings ioctls on subdev nodes
...
Add USB ID for Peak DVB-T USB.
[crope@iki.fi: fix Brian email address and indentation]
Signed-off-by: Brian Healy <healybrian@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It printed a little bit too heavy looking error log "DVB: Unable to
find symbol rtl2832_sdr_attach()" when staging module was disabled.
Silence that error by introducing own version of dvb_attach() macro
without the error logging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832 SDR extension module is currently on staging. SDR module
headers were included from staging causing direct dependency staging
directory. As a solution, add needed headers to main driver.
Motivation of that change comes from Luis / driver backports project.
Reported-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Cc: backports@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting functions for hardware filter is a bad idea, as it
breaks compilation if:
CONFIG_DVB_USB_AF9035=y
CONFIG_DVB_AF9033=m
Because the PID filter function calls would be hardcoded at
af9035.
The same doesn't happen with af9033_attach() because the
dvb_attach() doesn't hardcode it. Instead, it dynamically
links it at runtime.
However, calling dvb_attach() multiple times is problematic,
as it increments module kref.
So, the better is to pass one parameter for the af9033 module
to fill the hardware filters, and then use it inside af9035.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PID filters are property of af9033 demod. Use PID filters from af9033
driver as it provides those now.
Allow possible dual mode on USB 1.1 mode too as bandwidth could be
just enough when filters are used on both frontends.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832 driver provides muxed I2C adapters for tuner bus I2C gate
control. Pass those adapters to rtl2832_sdr and e4000 modules in order
to get rid of proprietary DVB .i2c_gate_ctrl() callback use.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We need depend on I2C_MUX as rtl2832 demod used requires it.
All error/warnings:
warning: (DVB_USB_RTL28XXU) selects DVB_RTL2832 which has unmet direct dependencies (MEDIA_SUPPORT && DVB_CORE && I2C && I2C_MUX)
ERROR: "i2c_add_mux_adapter" [drivers/media/dvb-frontends/rtl2832.ko] undefined!
ERROR: "i2c_del_mux_adapter" [drivers/media/dvb-frontends/rtl2832.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver conversion from proprietary DVB tuner model to more
general I2C driver model.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All used tuners has get_if_frequency() callback and that parameter
is not needed and will not needed as all upcoming tuner drivers
should implement get_if_frequency().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Disable IR interrupts in order to avoid SDR sample loss.
IR interrupts causes some extra load for device and it seems
be one reason to loss samples when sampling rate is high.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Following moving ids to af9035.
This driver is no longer in use.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some device vendors has forgotten set correct slave demod I2C address
to eeprom. Use default I2C address when eeprom has no address at all.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As follow on to patch
af9035: Move it913x single devices to af9035
and patch 1.
SNR is reported as db/10 values.
All dual ids are added to af9035 and it913x driver disabled.
it913x/it913x-fe removal patches to follow.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On some devices the vendor has not set EEPROM_2ND_DEMOD_ADDR.
Checks tmp is not zero after call to get EEPROM_2ND_DEMOD_ADDR and sets the
default slave address of 0x3a on 0x9135 devices.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The generic v1 and v2 devices have been all tested.
IDs tested
USB_PID_ITETECH_IT9135 v1 & v2
USB_PID_ITETECH_IT9135_9005 v1
USB_PID_ITETECH_IT9135_9006 v2
Current Issues
There is no signal on
USB_PID_ITETECH_IT9135 v2
No SNR reported all devices.
All single devices tune and scan fine.
All remotes tested okay.
Dual device failed to register second adapter
USB_PID_KWORLD_UB499_2T_T09
It is not clear what the problem is at the moment.
So only single IDs are transferred in this patch.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I've got the following DAB USB stick that also works fine with the
DVB_USB_RTL28XXU driver after I added its USB ID:
Bus 001 Device 009: ID 0ccd:00b4 TerraTec Electronic GmbH
[crope@iki.fi: apply patch partly manually]
Signed-off-by: Till Dörges <till@doerges.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add USB ID [2040:f900] for Hauppauge WinTV-MiniStick 2.
Device is build upon IT9135 chipset.
Tested-by: Stefan Becker <schtefan@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add USB ID [2040:f900] for Hauppauge WinTV-MiniStick 2.
Device is build upon IT9135 chipset.
Tested-by: Stefan Becker <schtefan@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the following build error:
drivers/media/usb/dvb-usb-v2/
mxl111sf-tuner.h:72:9: error: expected ‘;’, ‘,’ or ‘)’ before ‘struct’
struct mxl111sf_tuner_config *cfg)
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
mxl111sf_read_reg takes an address of a variable to write to as an argument.
drivers/media/usb/dvb-usb-v2/mxl111sf-gpio.c:mxl111sf_config_pin_mux_modes
passes several uninitialized stack variables to this routine, expecting
them to be filled in. In the event that something unexpected happens when
reading from the chip, we end up doing a pr_debug of the value passed in,
revealing whatever garbage happened to be on the stack.
Change the pr_debug to match what happens in the 'success' case, where we
assign buf[1] to *data.
Spotted with Coverity (Bugs 731910 through 731917)
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I am no longer available at the kernellabs.com or m1k.net email
addresses. Update each instance of my email to my linuxtv.org
account.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The rest of the function uses ret to store the return value, even setting
ret to i a few lines before this, so return ret instead of i.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PLL was attached twice to frontend0 leaving frontend1 without a tuner.
frontend0 is DVB-C and frontend1 is DVB-T.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
GIT_AUTHOR_DATE=1386943312
Add USB IDs for the WinFast DTV Dongle Mini.
Device is tested and works fine under MythTV
Signed-off-by: Robert Backhaus <robbak@robbak.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Merge the media fixes merged upstream for v3.13-rc4
* upstream-fixes: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
It is IT9135 dual design.
Thanks to Michael Piko for reporting that!
Reported-by: Michael Piko <michael@piko.com.au>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is similar to the Terratec H7. It works with the same az6007 firmware as
the former, however the drx-k firmware of the H7 will NOT work. Hence use
a different firmware name. The firmware does not need to exist as the one in
the eeprom is just fine as long as the h7 one doesn't get loaded, but maybe
some day someone wants to load it (the one from the h5 would work too).
Also since the config entry is now different anyway disable support for rc.
AFAIK the Technisat remote (TS35) is RC5 and the code (which a code comment
claims doesn't work anyway) only would handle NEC hence it's pointless creating
a device and polling it if we already know it can't work.
CI is untested.
Originally based on idea found on
http://www.linuxtv.org/wiki/index.php/TechniSat_CableStar_Combo_HD_CI claiming
only id needs to be added (but failed to mention it only worked because the
driver couldn't find the h7 drx-k firmware...).
Signed-off-by: Roland Scheidegger <rscheidegger_lists@hispeed.ch>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We introduced a couple new error paths which are missing unlocks.
Fixes: 7760e14835 ('[media] af9035: Don't use dynamic static allocation')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@vger.kernel.org
There was three small buffer len calculation bugs which caused
driver non-working. These are coming from recent commit:
commit 7760e14835
[media] af9035: Don't use dynamic static allocation
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@vger.kernel.org
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It is IT9135 dual design.
Thanks to Michael Piko for reporting that!
Reported-by: Michael Piko <michael@piko.com.au>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/mxl111sf.c:74:1: warning: 'mxl111sf_ctrl_msg' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/af9035.c:142:1: warning: 'af9035_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb-v2/af9035.c:305:1: warning: 'af9035_i2c_master_xfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/af9015.c:433:1: warning: 'af9015_eeprom_hash' uses dynamic stack allocation [enabled by default]
In this specific case, it is a gcc bug, as the size is a const, but
it is easy to just change it from const to a #define, getting rid of
the gcc warning.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Components are RTL2832P + R828D + MN88472.
Currently support only DVB-T as there is no driver for MN88472 demod.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832P is version of RTL2832U with extra TS interface.
As for now, we support only integrated RTL2832 demod.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Deferred probe was added in order to avoid udev vs. Kernel firmware
download problems. It is not needed anymore.
https://bugzilla.redhat.com/show_bug.cgi?id=827538
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to access bInterfaceNumber via dvb_usb_v2 internals as driver
has it already.
That patch is prepare for dvb_usb_v2 deferred probe hack removal. It was
added due to udev firmware loading problems, but things are fixed after
that and it is not needed anymore.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It is not allowed to build driver as a build-in when RC_CORE
(remote controller support) is build as a module.
randconfig build error with next-20130719, in drivers/media/usb
drivers/built-in.o: In function `dvb_usbv2_disconnect':
(.text+0x154b39): undefined reference to `rc_unregister_device'
drivers/built-in.o: In function `dvb_usbv2_init_work':
dvb_usb_core.c:(.text+0x155b2d): undefined reference to `rc_allocate_device'
dvb_usb_core.c:(.text+0x155c38): undefined reference to `rc_register_device'
dvb_usb_core.c:(.text+0x155c5b): undefined reference to `rc_free_device'
drivers/built-in.o: In function `anysee_rc_query':
anysee.c:(.text+0x157795): undefined reference to `rc_keydown'
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove the silly redefines of pr_err/info/debug.
This improves readability and it also gets rid of a bunch of warnings when
compiling this driver for older kernels using the compatibility media_build
system.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As suggested by Antti, this patch replaces:
https://patchwork.kernel.org/patch/2649861/
The buffer overflow is fixed by reading only the r820t ID register.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device has been tested on a MIPSel box with kernel 3.1.1 and backported media_tree drivers
The kernel detects the device with the following output:
usbcore: registered new interface driver dvb_usb_rtl28xxu
usb 1-2: dvb_usb_v2: found a 'Crypto Redi PC50A' in warm state
usb 1-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Crypto Redi PC50A)
usb 1-2: DVB: registering adapter 1 frontend 0 (Realtek RTL2832 (DVB-T))...
i2c i2c-4: fc0012: Fitipower FC0012 successfully identified
usb 1-2: dvb_usb_v2: 'Crypto Redi PC50A' successfully initialized and connected
[crope@iki.fi: fix trivial merge conflict]
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
USB ID 0413:6a03 is Leadtek WinFast DTV Dongle mini.
Decoder Realtek RTL2832U and tuner Infineon TUA9001.
Signed-off-by: Miroslav Šustek <sustmidown@centrum.cz>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
This patch uses the driver from openpli[1] as a template to restore the remote control support.
I had to divert from the original to use the in kernel rc protocol decoder. The key repetition does,
not seem to work but I cant find the problem in the driver. As a raw rc provider, no key table is
hardcoded.
Rodrigo.
[1]: https://aur.archlinux.org/packages/dvb-usb-rtl2832u-openpli/?comments=all
Signed-off-by: Rodrigo Tartajo <rtarty@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested on a MIPSel box with 3.3.6 kernel
The kernel output when the device will be detected follows:
usbcore: registered new interface driver dvb_usb_it913x
it913x: Chip Version=01 Chip Type=9135
it913x: Remote propriety (raw) mode
it913x: Dual mode=3 Tuner Type=38
it913x: Chip Version=01 Chip Type=9135
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in cold state
usb 2-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9137-01.fw'
it913x: FRM Starting Firmware Download
it913x: FRM Firmware Download Completed - Resetting Device
it913x: Chip Version=01 Chip Type=9135
it913x: Firmware Version 204147968
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in warm state
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 1 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_1)...
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 2 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_2)...
usb 2-1: dvb_usb_v2: 'Digital Dual TV Receiver CTVDIGDUAL_V2' successfully initialized and connected
RC part not tested
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* topic/r820t: (31 commits)
[media] r820t: Don't divide the IF by two
[media] r820t: disable auto gain/VGA setting
[media] rtl2832: Fix IF calculus
[media] r820t: put it into automatic gain mode
[media] r820t: Fix hp_cor filter mask
[media] r820t: fix PLL calculus
[media] r820t: Don't put it in standby if not initialized yet
[media] r820t: avoid rewrite all regs when not needed
[media] r820t: Allow disabling IMR callibration
[media] r820t: add a commented code for GPIO
[media] r820t: add IMR calibrate code
[media] r820t: proper initialize the PLL register
[media] r820t: use usleep_range()
[media] r820t: fix prefix of the r820t_read() function
[media] r820t: split the function that read cached regs
[media] r820t: better report signal strength
[media] r820t: add support for diplexer
[media] r820t: Show the read data in the bit-reversed order
[media] r820t: use the second table for 7MHz
[media] r820t: Invert bits for read ops
...
drivers/media/usb/dvb-usb-v2/anysee.c: In function ‘anysee_frontend_attach’:
drivers/media/usb/dvb-usb-v2/anysee.c:641: warning: ‘ret’ may be used uninitialized in this function
And gcc is right (see the ANYSEE_HW_507T case), so initialize ret to zero
to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we can get the strength from r820t, use it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
This tuner is used on some rtl2882 dongles. Add it to the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
There are three drivers with *it913x name on it, and they all
belong to the same device:
a tuner, at it913x.c;
a frontend: it913x-fe.c;
a bridge: it913x.c, renamed to dvb_usb_it913x by the
building system.
This is confusing. Even more confusing are the two .c files with
the same name under different directories, with different contents
and different functions. So, prepend the tuner one.
This also breaks the out-of-tree compilation system.
Reported-by: Frederic Fays <frederic.fays@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Loading the cypress firmware is not dvb specific and should be common
functionality. Move the source to media/common and make it a standalone
module.
As a result we can remove the dependency on dvb-usb in go7007, which has
nothing to do with dvb.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the missing unlock before return from function af9035_ctrl_msg()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enable dual tuner for Avermedia Twinstar.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I just made commit: "dvb_usb_v2: rework USB streaming logic" that
breaks that driver PID filter.
it913x driver checks use of PID filter directly from DVB USB v2 core
internal variable "adap->pid_filtering" and stores it to own state.
Calling order of .pid_filter_ctrl() and .pid_filter() was changed
and due to that state was updated too late. Update state earlier.
TODO: checking PID filter usage from DVB USB v2 is not very good idea
as PID filter callbacks are called only when PID filter is enabled.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Control flow order changed a little bit. HW PID filter is now
disabled also when streaming is stopped - earlier it was just
set only when streaming was started.
Control flow is now:
* set streaming status bit
* submit USB streaming packets
* enable HW PID filter
* ask device to start streaming
* N x add PID to device HW PID filter
... streaming video ...
* N x remove PID from device HW PID filter
* ask device to stop streaming
* disable HW PID filter
* kill USB streaming packets
* clear streaming status bit
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New checkpatch version likes to see strings not to split multiple
lines even those are exceeding 80 line length.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New checkpatch version likes to see strings not to split multiple
lines even those are exceeding 80 line length.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was sync mutex which was held over userspace. That is very
wrong and could cause deadlock if different userspace process is
used to "unlock". Wait queue seems to be correct solution for
that kind of synchronizing issue so use it instead.
lock debug gives following bug report:
================================================
[ BUG: lock held when returning to user space! ]
3.9.0-rc1+ #38 Tainted: G O
------------------------------------------------
tzap/4614 is leaving the kernel with locks still held!
1 lock held by tzap/4614:
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb_usb_v2_generic_io() was not declared. It should be static.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some reason there seems to be value 0x03 in eeprom for dual mode
(and 0x00 for single mode). Boolean is not always 1 bit wide - it
could be 8 bit wide too. Storing number 0x03 to boolean causes driver
to thing there is 4 tuners in some cases :o
Add also some comments regarding to eeprom.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no difference towards AF9035 remote controller, so enable it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
eeprom memory mapped base address is detected at the very first.
Use it everywhere.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
AF9035 and IT9135 supports two different firmware format. Select
correct loader according to first byte of firmware file.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't need it. Tuner ID and device address are enough.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now it supports IT9135 based dual tuner devices.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That same USB ID is used both AF9015 and AF9035 driver.
iManufacturer is only thing we can select correct driver without a I/O.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That same USB ID is used both AF9015 and AF9035 driver.
iManufacturer is only thing we can select correct driver without a I/O.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ADC needs to be also multiplied to 2 as it9135.
Fixes bug I introduced few commits ago.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Detect automatically multiple chip versions and select configuration
according to that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I did what I liked to do. Also corrected two long log writings
as checkpatch.pl was complaining about those.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement:
dvb_usbv2_generic_rw_locked()
dvb_usbv2_generic_write_locked()
Caller must hold device lock when locked versions are called.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Check for (adap == NULL) has to done before accessing adap.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds USB ID for alternative "Terratec Cinergy T Stick".
Tested by a friend: works similarly to 0ccd:0093 version (af9035+tua9001)
Signed-off-by: Fabrizio Gazzato <fabrizio.gazzato@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID for MaxMedia HU394-T USB DVB-T Multi (FM, DAB, DAB+)
dongle (RTL2832U+FC0012)
In Italy, is branded as "DIKOM USB-DVBT HD"
lsusb: ID 1b80:d394 Afatech
Signed-off-by: Fabrizio Gazzato <fabrizio.gazzato@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
- Some cleanups at V4L2 documentation
- new drivers: ts2020 frontend, ov9650 sensor, s5c73m3 sensor,
sh-mobile veu mem2mem driver, radio-ma901, davinci_vpfe staging
driver
- Lots of missing MAINTAINERS entries added
- several em28xx driver improvements, including its conversion to
videobuf2
- several fixups on drivers to make them to better comply with the API
- DVB core: add support for DVBv5 stats, allowing the implementation of
statistics for new standards like ISDB
- mb86a20s: add statistics to the driver
- lots of new board additions, cleanups, and driver improvements.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (596 commits)
[media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
[media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
[media] em28xx: add usb id for terratec h5 rev. 3
[media] media: rc: gpio-ir-recv: add support for device tree parsing
[media] mceusb: move check earlier to make smatch happy
[media] radio-si470x doc: add info about v4l2-ctl and sox+alsa
[media] staging: media: Remove unnecessary OOM messages
[media] sh_vou: Use vou_dev instead of vou_file wherever possible
[media] sh_vou: Use video_drvdata()
[media] drivers/media/platform/soc_camera/pxa_camera.c: use devm_ functions
[media] mt9t112: mt9t111 format set up differs from mt9t112
[media] sh-mobile-ceu-camera: fix SHARPNESS control default
Revert "[media] fc0011: Return early, if the frequency is already tuned"
[media] cx18/ivtv: fix regression: remove __init from a non-init function
[media] em28xx: fix analog streaming with USB bulk transfers
[media] stv0900: remove unnecessary null pointer check
[media] fc0011: Return early, if the frequency is already tuned
[media] fc0011: Add some sanity checks and cleanups
[media] fc0011: Fix xin value clamping
Revert "[media] [PATH,1/2] mxl5007 move reset to attach"
...
Add support for Digivox Mini HD (rtl2832)
The tuner works, but with worst performance then realtek linux driver,
due to incomplete implementation of fc2580.c
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
Tested-by: Lorenzo Dongarrà <lorenzo_64@katamail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device with ID 1b80:d393 is the Gigabyte U7300 DVB-T dongle.
It contains decoder Realtek RTL2832U and tuner Fitipower FC0012.
[crope@iki.fi: fix trivial merge conflict]
Signed-off-by: Alexander Inyukhin <shurick@sectorb.msk.ru>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use own flag to mark when rc polling is active/deactive and make
decisions, like start/stop polling on suspend/resume, against that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I think it is better (cheaper) to use dummy defines for functions
that has no meaning when remote controller is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those are not needed anymore as all dvb-usb-v2 drivers has proper
dependency checks for RC-core.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not compile remote controller when RC-core is disabled by Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it possible to compile dvb_usb_v2 driver without the remote
controller (RC-core).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No need to copy config to the driver state. Those are coming from
the const struct and could be used directly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That adds support for AF9035 dual devices having FC0012 tuners.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I need even more configuration options and overloading dvb_attach()
for all those sounds quite stupid. Due to that switch struct and make
room for new options.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Various small changes and fixes releated to dual mode.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
