Use dma-direct unconditionally on arm. It has already been used for
some time for LPAE and nommu configurations.
This mostly changes the streaming mapping implementation and the (simple)
coherent allocator for device that are DMA coherent. The existing
complex allocator for uncached mappings for non-coherent devices is still
used as is using the arch_dma_alloc/arch_dma_free hooks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andre Przywara <andre.przywara@arm.com> [highbank]
Tested-by: Marc Zyngier <maz@kernel.org>
Choosing big-endian vs little-endian kernels in Kconfig has not worked
correctly since the introduction of CONFIG_ARCH_MULTIPLATFORM a long
time ago.
The problems is that CONFIG_BIG_ENDIAN depends on
ARCH_SUPPORTS_BIG_ENDIAN, which can set by any one platform
in the config, but would actually have to be supported by all
of them.
This was mostly ok for ARMv6/ARMv7 builds, since these are BE8 and
tend to just work aside from problems in nonportable device drivers.
For ARMv4/v5 machines, CONFIG_BIG_ENDIAN and CONFIG_ARCH_MULTIPLATFORM
were never set together, so this was disabled on all those machines
except for IXP4xx.
As IXP4xx can now become part of ARCH_MULTIPLATFORM, it seems better to
formalize this logic: all ARMv4/v5 platforms get an explicit dependency
on being either big-endian (ixp4xx) or little-endian (the rest). We may
want to fix ixp4xx in the future to support both, but it does not work
in LE mode at the moment.
For the ARMv6/v7 platforms, there are two ways this could be handled
a) allow both modes only for platforms selecting
'ARCH_SUPPORTS_BIG_ENDIAN' today, but only LE mode for the
others, given that these were added intentionally at some
point.
b) allow both modes everwhere, given that it was already possible
to build that way by e.g. selecting ARCH_VIRT, and that the
list is not an accurate reflection of which platforms may or
may not work.
Out of these, I picked b) because it seemed slighly more logical
to me.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM is the only architecture that defines CONFIG_ARCH_HAS_HOLES_MEMORYMODEL
which in turn enables memmap_valid_within() function that is intended to
verify existence of struct page associated with a pfn when there are holes
in the memory map.
However, the ARCH_HAS_HOLES_MEMORYMODEL also enables HAVE_ARCH_PFN_VALID
and arch-specific pfn_valid() implementation that also deals with the holes
in the memory map.
The only two users of memmap_valid_within() call this function after
a call to pfn_valid() so the memmap_valid_within() check becomes redundant.
Remove CONFIG_ARCH_HAS_HOLES_MEMORYMODEL and memmap_valid_within() and rely
entirely on ARM's implementation of pfn_valid() that is now enabled
unconditionally.
Link: https://lkml.kernel.org/r/20201101170454.9567-9-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split out all the bits that are purely for dma_map_ops implementations
and related code into a new <linux/dma-map-ops.h> header so that they
don't get pulled into all the drivers. That also means the architecture
specific <asm/dma-mapping.h> is not pulled in by <linux/dma-mapping.h>
any more, which leads to a missing includes that were pulled in by the
x86 or arm versions in a few not overly portable drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus Walleij--
the SoC doesn't have active maintainers with hardware, and in
discussions with the vendor the agreement was that it's OK to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl0yKOgPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3SNEP/iJsMeeunX0P7Ym3zNFjykhspkkUmo7sEKuz
NBcexnQpkm+OLgjfwT7j3kXvOs4mzMzH56J6h7dEDSHbQP1MDIgpMw6OEzMMsQTV
XL1AWz1IO7Sq/mG17daPs9c75o6NYQ7pSEd/ncbjKuJQOpGsi4DyrVrhk9WdzYl2
hcs4XOzOMZgDTsXHVdWkfpHazpWxEXPCD7v5bt6ueU0YnT3csUbzOTTvw+55JxRV
fYz0lg4wTMRYMQMOejpx1HXwdmbVOHLUYkCxcLUaVqMnm88q/IddJVklBbPGWAU5
Z4gFpL+FxcFhEZtu28CoubPYzf/mHDk8Ry2UWwBiRwiGoKfblomI1fpnbyrX53aE
lpO5p7MfOVVV2WNxpbUND+ilbgKOREfRHd314GLPUjwudp2sTuDRZ1GAbt3JwsIM
L1HesyjCtb6itCSwGsmmGsX2Wvu+WT7slpsYwHs2qklE/X1zQq0R4Jf2xUNpwqPb
FqGZAtc6CCQtyF/Mcpp6OQd+cV0tgQVIw7teKol/xR1dSzN/+1zO1J9UHk9/dWUU
sb5lGa/AtBrIbWxS1qLuA5bgyDqxXYDZi0y/Bu1qMHYebRW37z9kvomtzBiMNX2o
SAxvr9iGPlTxTjGjRCyBVFmsbCMYLabNoL9tuuXvo+DnjFoOilTef+qePOv7ZYZX
kwUyS2eu
=FX6e
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus
Walleij-- the SoC doesn't have active maintainers with hardware,
and in discussions with the vendor the agreement was that it's OK
to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: stm32: use "depends on" instead of "if" after prompt
ARM: sa1100: convert to common clock framework
ARM: exynos: Cleanup cppcheck shifting warning
ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view
ARM: exynos: Only build MCPM support if used
arm: add missing include platform-data/atmel.h
ARM: davinci: Use GPIO lookup table for DA850 LEDs
ARM: OMAP2: drop explicit assembler architecture
ARM: use arch_extension directive instead of arch argument
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
MAINTAINERS: mvebu: Add git entry
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
...
The LLVM Target parser currently does not allow to specify the security
extension as part of -march (see also LLVM Bug 40186 [0]). When trying
to use Clang with LLVM's integrated assembler, this leads to build
errors such as this:
clang-8: error: the clang compiler does not support '-Wa,-march=armv7-a+sec'
Use ".arch_extension sec" to enable the security extension in a more
portable fasion. Also make sure to use ".arch armv7-a" in case a v6/v7
multi-platform kernel is being built.
Note that this is technically not exactly the same as the old code
checked for availabilty of the security extension by calling as-instr.
However, there are already other sites which use ".arch_extension sec"
unconditionally, hence de-facto we need an assembler capable of
".arch_extension sec" already today (arch/arm/mm/proc-v7.S). The
arch extension "sec" is available since binutils 2.21 according to
its documentation [1].
[0] https://bugs.llvm.org/show_bug.cgi?id=40186
[1] https://sourceware.org/binutils/docs-2.21/as/ARM-Options.html
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Mans Rullgard <mans@mansr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define this symbol if the architecture either uses 64-bit pointers or the
PHYS_ADDR_T_64BIT is set. This covers 95% of the old arch magic. We only
need an additional select for Xen on ARM (why anyway?), and we now always
set ARCH_DMA_ADDR_T_64BIT on mips boards with 64-bit physical addressing
instead of only doing it when highmem is set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: James Hogan <jhogan@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After patch "of/platform: Add common method to populate default bus",
it is possible for arch code to remove unnecessary callers of
of_platform_populate with default match table.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Lee Jones <lee@kernel.org>
Cc: Krzysztof Halasa <khalasa@piap.pl>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Viresh Kumar <vireshk@kernel.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Many ARM sub-architectures use prompts followed by "if" conditional,
but it is wrong.
Please notice the difference between
config ARCH_FOO
bool "Foo SoCs" if ARCH_MULTI_V7
and
config ARCH_FOO
bool "Foo SoCs"
depends on ARCH_MULTI_V7
These two are *not* equivalent!
In the former statement, it is not ARCH_FOO, but its prompt that
depends on ARCH_MULTI_V7. So, it is completely valid that ARCH_FOO
is selected by another, but ARCH_MULTI_V7 is still disabled. As it is
not unmet dependency, Kconfig never warns. This is probably not what
you want.
The former should be used only when you need to do so, and you really
understand what you are doing. (In most cases, it should be wrong!)
For enabling/disabling sub-architectures, the latter is always correct.
As a good side effect, this commit fixes some entries over 80 columns
(mach-imx, mach-integrator, mach-mbevu).
[Arnd: I note that there is not really a bug here, according to
the discussion that followed, but I can see value in being consistent
and in making the lines shorter]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Halasa <khc@piap.pl>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that the common PSCI client code has been factored out to
drivers/firmware, and made safe for 32-bit use, move the 32-bit ARM code
over to it. This results in a moderate reduction of duplicated lines,
and will prevent further duplication as the PSCI client code is updated
for PSCI 1.0 and beyond.
The two legacy platform users of the PSCI invocation code are updated to
account for interface changes. In both cases the power state parameter
(which is constant) is now generated using macros, so that the
pack/unpack logic can be killed in preparation for PSCI 1.0 power state
changes.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The definition
static const char *axxia_dt_match[] __initconst = {
...
defines a changable array of constant strings. That is you must not do:
*axxia_dt_match[0] = 'k';
but
axxia_dt_match[0] = "different string";
is fine. So the annotation __initconst is wrong and yields a compiler
error when other really const variables are added with __initconst.
As the struct machine_desc member dt_compat is declared as
const char *const *dt_compat;
making the arrays const is the better alternative over changing all
annotations to __initdata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The patch 30058677 "ARM / highbank: add support for pl320 IPC"
added a pl320 IPC specific header file as a generic mailbox.h.
This file has been renamed appropriately to allow the
introduction of the generic mailbox API framework.
Acked-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Since the OPP layer is a kernel library which has been converted to be
directly selectable by its callers rather than user selectable and
requiring architectures to enable it explicitly the ARCH_HAS_OPP symbol
has become redundant and can be removed. Do so.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This config exists entirely to hide the cpufreq menu from the
kernel configuration unless a platform has selected it. Nothing
is actually built if this config is 'Y' and it just leads to more
patches that add a select under a platform Kconfig so that some
other CPUfreq option can be chosen. Let's remove the option so
that we can always enable CPUfreq drivers on ARM platforms.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove the explicit call to l2x0_of_init(), converting to the generic
infrastructure instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that highbank uses the write_sec method, we don't need to enable
the L2 cache in SoC specific code; this can be done via the normal
mechanisms in the L2C code.
Checking with Rob Herring:
> > Can we kill the "highbank_smc1(0x102, 0x1);" here? That means
> > l2x0_of_init() will see the L2 cache disabled, and will try to enable
> > it via the write_sec hook, so it should do the right thing.
>
> Yes, that should work. You should be able to just call l2x0_of_init
> unconditionally. The condition was really to just avoid the smc on
> Midway which does get handled on h/w, but not if running virtualized.
So also drop the DT check too. I'm leaving the config check in place
so that if L2 is disabled, the write_sec hook can be optimised away.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the write_sec method, we no longer need to override the default L2C
disable method. This can be handled via the write_sec method instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
They're u32, they're not unsigned long. The UL suffix is not required
here.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All V7 platforms can run SMP kernels, so make CONFIG_SMP visible for V7
multi-platform builds.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Multi-platform requires various kconfig options to be selected, so
platforms don't need to select them individually.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Pull ARM fixes from Russell King:
"Another few fixes for ARM, nothing major here"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7938/1: OMAP4/highbank: Flush L2 cache before disabling
ARM: 7939/1: traps: fix opcode endianness when read from user memory
ARM: 7937/1: perf_event: Silence sparse warning
ARM: 7934/1: DT/kernel: fix arch_match_cpu_phys_id to avoid erroneous match
Revert "ARM: 7908/1: mm: Fix the arm_dma_limit calculation"
Kexec disables outer cache before jumping to reboot code, but it doesn't
flush it explicitly. Flush is done implicitly inside of l2x0_disable().
But some SoC's override default .disable handler and don't flush cache.
This may lead to a corrupted memory during Kexec reboot on these
platforms.
This patch adds cache flush inside of OMAP4 and Highbank outer_cache.disable()
handlers to make it consistent with default l2x0_disable().
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Graceful reboot and poweroff via IPMI commands to the management
processor don't work. Power and reset keys are events from the
management processor which are generated via IPC messages. Passing
the keys to userspace does not work as neither acpid nor a desktop
environment are present.
This adds a notifier handler for the IPC messages so the kernel can
handle the key events directly and IPMI graceful shutdown will work.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
A first set of batches of fixes for 3.13. The diffstat is large mostly
because we're adding a defconfig for a family that's been lacking it, and
there's some missing clock information added for i.MX and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix possible
hangs due to pending wakeup interrupts coming in during early boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0oVK
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A first set of batches of fixes for 3.13. The diffstat is large
mostly because we're adding a defconfig for a family that's been
lacking it, and there's some missing clock information added for i.MX
and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix
possible hangs due to pending wakeup interrupts coming in during early
boot"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: at91: fix hanged boot due to early rtt-interrupt
ARM: at91: fix hanged boot due to early rtc-interrupt
video: exynos_mipi_dsim: Remove unused variable
ARM: highbank: only select errata 764369 if SMP
ARM: sti: only select errata 764369 if SMP
ARM: tegra: init fuse before setting reset handler
ARM: vt8500: add defconfig for v6/v7 chips
ARM: integrator_cp: Set LCD{0,1} enable lines when turning on CLCD
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
MAINTAINERS: drop discontinued mailing list
ARM: dts: i.MX51: Fix OTG PHY clock
ARM: imx: set up pllv3 POWER and BYPASS sequentially
ARM: imx: pllv3 needs relock in .set_rate() call
...
764369 depends on SMP, so don't select it on !SMP configs.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Pull ARM updates from Russell King:
"Included in this series are:
1. BE8 (modern big endian) changes for ARM from Ben Dooks
2. big.Little support from Nicolas Pitre and Dave Martin
3. support for LPAE systems with all system memory above 4GB
4. Perf updates from Will Deacon
5. Additional prefetching and other performance improvements from Will.
6. Neon-optimised AES implementation fro Ard.
7. A number of smaller fixes scattered around the place.
There is a rather horrid merge conflict in tools/perf - I was never
notified of the conflict because it originally occurred between Will's
tree and other stuff. Consequently I have a resolution which Will
forwarded me, which I'll forward on immediately after sending this
mail.
The other notable thing is I'm expecting some build breakage in the
crypto stuff on ARM only with Ard's AES patches. These were merged
into a stable git branch which others had already pulled, so there's
little I can do about this. The problem is caused because these
patches have a dependency on some code in the crypto git tree - I
tried requesting a branch I can pull to resolve these, and all I got
each time from the crypto people was "we'll revert our patches then"
which would only make things worse since I still don't have the
dependent patches. I've no idea what's going on there or how to
resolve that, and since I can't split these patches from the rest of
this pull request, I'm rather stuck with pushing this as-is or
reverting Ard's patches.
Since it should "come out in the wash" I've left them in - the only
build problems they seem to cause at the moment are with randconfigs,
and since it's a new feature anyway. However, if by -rc1 the
dependencies aren't in, I think it'd be best to revert Ard's patches"
I resolved the perf conflict roughly as per the patch sent by Russell,
but there may be some differences. Any errors are likely mine. Let's
see how the crypto issues work out..
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (110 commits)
ARM: 7868/1: arm/arm64: remove atomic_clear_mask() in "include/asm/atomic.h"
ARM: 7867/1: include: asm: use 'int' instead of 'unsigned long' for 'oldval' in atomic_cmpxchg().
ARM: 7866/1: include: asm: use 'long long' instead of 'u64' within atomic.h
ARM: 7871/1: amba: Extend number of IRQS
ARM: 7887/1: Don't smp_cross_call() on UP devices in arch_irq_work_raise()
ARM: 7872/1: Support arch_irq_work_raise() via self IPIs
ARM: 7880/1: Clear the IT state independent of the Thumb-2 mode
ARM: 7878/1: nommu: Implement dummy early_paging_init()
ARM: 7876/1: clear Thumb-2 IT state on exception handling
ARM: 7874/2: bL_switcher: Remove cpu_hotplug_driver_{lock,unlock}()
ARM: footbridge: fix build warnings for netwinder
ARM: 7873/1: vfp: clear vfp_current_hw_state for dying cpu
ARM: fix misplaced arch_virt_to_idmap()
ARM: 7848/1: mcpm: Implement cpu_kill() to synchronise on powerdown
ARM: 7847/1: mcpm: Factor out logical-to-physical CPU translation
ARM: 7869/1: remove unused XSCALE_PMU Kconfig param
ARM: 7864/1: Handle 64-bit memory in case of 32-bit phys_addr_t
ARM: 7863/1: Let arm_add_memory() always use 64-bit arguments
ARM: 7862/1: pcpu: replace __get_cpu_var_uses
ARM: 7861/1: cacheflush: consolidate single-CPU ARMv7 cache disabling code
...
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
Merging in dt clock cleanup as a pre-req with some of the later SoC branches.
There are a handful of conflicts here -- some of the already merged SoC
branches should have been based on the cleanup but weren't.
In particular, a remove/add of include on highbank and two remove/remove
conflicts on kirkwood were fixed up.
* cleanup/dt-clock: (28 commits)
ARM: vt8500: remove custom .init_time hook
ARM: vexpress: remove custom .init_time hook
ARM: tegra: remove custom .init_time hook
ARM: sunxi: remove custom .init_time hook
ARM: sti: remove custom .init_time hook
ARM: socfpga: remove custom .init_time hook
ARM: rockchip: remove custom .init_time hook
ARM: prima2: remove custom .init_time hook
ARM: nspire: remove custom .init_time hook
ARM: nomadik: remove custom .init_time hook
ARM: mxs: remove custom .init_time hook
ARM: kirkwood: remove custom .init_time hook
ARM: imx: remove custom .init_time hook
ARM: highbank: remove custom .init_time hook
ARM: exynos: remove custom .init_time hook
ARM: dove: remove custom .init_time hook
ARM: bcm2835: remove custom .init_time hook
ARM: bcm: provide common arch init for DT clocks
ARM: call of_clk_init from default time_init handler
ARM: vt8500: prepare for arch-wide .init_time callback
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Several configurations are selecting errata 798181 without SMP
being selected. This causes a warning from Kconfig:
warning: (ARCH_HIGHBANK && ARCH_KEYSTONE && SOC_OMAP5 && ARCH_TEGRA_114_SOC) selects ARM_ERRATA_798181 which has unmet direct dependencies (CPU_V7 && SMP)
The dependencies are compile time dependencies; select violates these,
resulting in:
arch/arm/kernel/built-in.o: In function `setup_processor':
psci.c:(.init.text+0x808): undefined reference to `erratum_a15_798181_init'
at build time. Fix this by fixing the select statements for Tegra and
Highbank.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Apart from a xgmac driver issue, the highbank seems to work correctly in
big-endian mode. Allow the selection of big-endian in the system.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Rob Herring <rob.herring@calxeda.com>
CLKDEV_LOOKUP selects HAVE_CLK and COMMON_CLK selects CLKDEV_LOOKUP. So
all symbols that select at least two of these symbols can be simplified.
For imx, omap2 and ux500 some rearrangements were necessary before the
simplification.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This updates the Calxeda cpuidle driver to use PSCI calls to powergate
cores. This also enables cpuidle for the ECX-2000.
This could possibly become a generic PSCI driver, but there are no other
PSCI users in the kernel other than mach-virt.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-pm@vger.kernel.org
As the ux500 and the kirkwood driver, make the calxeda driver a platform driver
[Compiled only]
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
With arch/arm calling of_clk_init(NULL) from time_init(), we can now
remove custom .init_time hooks. Highbank clock provider need a reference
to system registers, as a workaround current clk driver maps those
independent of arch code now.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NIZZ
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Kevin Hilman:
"These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: dts: vexpress: Add CCI node to TC2 device-tree
ARM: EXYNOS: Skip C1 cpuidle state for exynos5440
ARM: EXYNOS: always enable PM domains support for EXYNOS4X12
ARM: highbank: clean-up some unused includes
ARM: sun7i: Enable the A20 clocks in the DTSI
ARM: sun6i: Enable clock support in the DTSI
ARM: sun5i: dt: Use the A10s gates in the DTSI
ARM: at91: at91_dt_defconfig: enable rm9200 support
ARM: dts: add ADC device tree node for exynos5420/5250
ARM: dts: Add RTC DT node to Exynos5420 SoC
ARM: dts: Update the "status" property of RTC DT node for Exynos5250 SoC
ARM: dts: Fix the RTC DT node name for Exynos5250
irqchip: mmp: avoid to include irqs head file
ARM: mmp: avoid to include head file in mach-mmp
irqchip: mmp: support irqchip
irqchip: move mmp irq driver
ARM: OMAP: AM33xx: clock: Add RNG clock data
ARM: OMAP: TI81XX: add always-on powerdomain for TI81XX
ARM: OMAP4: clock: Lock PLLs in the right sequence
ARM: OMAP: AM33XX: hwmod: Add hwmod data for debugSS
...
While Midway firmware handles L2 smc calls as nops, the custom smc calls
present a problem when running virtualized Midway guest. They aren't
needed so just avoid calling them.
In the process, cleanup the L2X0 ifdefs and use IS_ENABLED instead.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Ensure necessary errata work-arounds are always enabled for Highbank
and Midway platforms. Highbank requires 764369 and 764369. Midway requires
798181, but only the first half of the work-around (no IPI). Support for
skipping the IPI is introduced in another commit.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
On Midway, the first 4G of memory starts at 0 and the rest of memory
(4GB+) starts at 0x2_00000000, so we need to enable pfn_valid checks
by selecting ARCH_HAS_HOLES_MEMORYMODEL.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Some devices are restricted to 32-bit DMA. Thus the platform dma_zone_size
needs to be set. Otherwise dma-mapping code is complaining, e.g.
calxedaxgmac fff50000.ethernet: coherent DMA mask 0xffffffff is smaller
than system GFP_DMA mask 0xffffffffffffffff
Signed-off-by: Andreas Herrmann <andreas.herrmann@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
series involve following modifications:
1) fixing up few things in samsung_pwm_timer clocksource driver,
2) moving remaining Samsung platforms to the new clocksource driver,
3) removing old clocksource driver,
4) adding new multiplatform- and DT-aware PWM driver,
5) moving all Samsung platforms to use the new PWM driver,
6) removing old PWM driver,
7) removing all PWM-related code that is not used anymore.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=xmmW
-----END PGP SIGNATURE-----
Merge tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux into next/cleanup
From Tomasz Figa:
Here is the Samsung PWM cleanup series. Particular patches of the series
involve following modifications:
- fixing up few things in samsung_pwm_timer clocksource driver,
- moving remaining Samsung platforms to the new clocksource driver,
- removing old clocksource driver,
- adding new multiplatform- and DT-aware PWM driver,
- moving all Samsung platforms to use the new PWM driver,
- removing old PWM driver,
- removing all PWM-related code that is not used anymore.
* tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux: (684 commits)
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
pwm: samsung: Rename to pwm-samsung-legacy
ARM: SAMSUNG: Remove unused PWM timer IRQ chip code
ARM: SAMSUNG: Remove old samsung-time driver
ARM: SAMSUNG: Move all platforms to new clocksource driver
ARM: SAMSUNG: Set PWM platform data
ARM: SAMSUNG: Add new PWM platform device
ARM: SAMSUNG: Unify base address definitions of timer block
clocksource: samsung_pwm_timer: Handle suspend/resume correctly
clocksource: samsung_pwm_timer: Do not use clocksource_mmio
clocksource: samsung_pwm_timer: Cache clocksource register address
clocksource: samsung_pwm_timer: Correct definition of AUTORELOAD bit
clocksource: samsung_pwm_timer: Do not request PWM mem region
+ v3.11-rc4
Conflicts:
arch/arm/Kconfig.debug
Signed-off-by: Olof Johansson <olof@lixom.net>
timer API entirely. Doing so will reduce code in ARM core, reduce the
architecture dependencies of our timer drivers, and simplify the code because
we no longer go through an architecture layer that is essentially a hotplug
notifier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=wZbm
-----END PGP SIGNATURE-----
Merge tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From Stephen Boyd:
Now that we have a generic arch hook for broadcast we can remove the
local timer API entirely. Doing so will reduce code in ARM core, reduce
the architecture dependencies of our timer drivers, and simplify the code
because we no longer go through an architecture layer that is essentially
a hotplug notifier.
* tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: smp: Remove local timer API
clocksource: time-armada-370-xp: Divorce from local timer API
clocksource: time-armada-370-xp: Fix sparse warning
ARM: msm: Divorce msm_timer from local timer API
ARM: PRIMA2: Divorce timer-marco from local timer API
ARM: EXYNOS4: Divorce mct from local timer API
ARM: OMAP2+: Divorce from local timer API
ARM: smp_twd: Divorce smp_twd from local timer API
ARM: smp: Remove duplicate dummy timer implementation
Resolved a large number of conflicts due to __cpuinit cleanups, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Midway adds new register fields to the coherency control registers, so
writing absolute values will break on Midway. Change the register
accesses to only modify the necessary and common fields in order to
support both Midway and Highbank.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
