There is a V4L2 sub-device sensor driver for the mt9m001.
There is already a non-soc_camera driver. So, remove the SoC camera
one.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
According to the ov5640 specification (2.7 power up sequence), host can
access the sensor's registers 20ms after reset. Trying to access them
before leads to undefined behavior and result in sporadic initialization
errors.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov5640_try_frame_interval operation updates the FPS as per user
input based on default ov5640_frame_rate, OV5640_30_FPS which is failed
to update when user trigger 15fps.
So, initialize the default ov5640_frame_rate to OV5640_15_FPS so-that
it can satisfy to update all fps.
Fixes: 5a3ad937bc ("media: ov5640: Make the return rate type more explicit")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The register value lists for all the supported resolution settings all
include a register address/value pair for setting the JPEG compression
mode. With the exception of 1080p (which sets mode 2), all resolutions
use mode 3.
The only difference between mode 2 and mode 3 is that mode 2 may have
padding data on the last line, while mode 3 does not add padding data.
As these register values were from dumps of running systems, and the
difference between the modes is quite small, using mode 3 for all
configurations should be OK.
[Sakari Ailus: Align OV5640_REG_JPG_MODE_SELECT register naming.]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When compression is turned on, the on-bus data is framed according to
the compression mode, and the height and width set in VFIFO_VSIZE and
VFIFO_HSIZE. If these are not updated correctly, the sensor will send
data framed in a manner unexpected by the capture interface, such as
having more bytes per line than expected, and having the extra data
dropped. This ultimately results in corrupted data.
Set the two values when the media bus is configured for JPEG data,
meaning the sensor would be in JPEG mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The OV5640 driver currently supports a static color bar pattern with a
small vertical gamma gradient. The hardware also supports a color square
pattern, as well as having a rolling bar for dynamic sequences.
Add three more test patterns:
- color bars with a rolling bar (but without the gamma gradient)
- static color squares
- color squares with a rolling bar
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The transparent feature for test patterns blends the test pattern with
an actual captured image. This makes the result non-static, subject to
changes in the sensor's field of view.
Test patterns should be predictable and deterministic, even if they are
dynamic patterns. Disable the transparent feature of the test pattern.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The OV5640 can generate many types of test patterns, some with
additional modifiers, such as a rolling bar, or gamma gradients.
Add the bit definitions for all bits in the test pattern register,
and use them to compose the values to be written to the register.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The OV5640 has many options for generating test patterns. Unfortunately
there is only one V4L2 control for it. Thus the driver would need to
list some or all combinations.
Move the test_pattern_menu list before the ov5640_set_ctrl_test_pattern
function that programs the hardware. This would allow us to add a
matching list of values to program into the hardware, while keeping the
two lists together for ease of maintenance.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748X_PAGE_WAIT is a fake page to insert arbitrary delays in the
register tables.
Its only usage was removed, so we can remove the handling and simplify
the code.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748x is currently reset by writting a small table of registers to
the device.
The table lacks documentation and contains magic values to perform the
actions, including using a fake register address to introduce a delay
loop.
Remove the table, and convert to code, documenting the purpose of the
specific writes along the way.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the adv748x driver is informed about a link being created from HDMI or
AFE to a CSI-2 TX output, the 'link_setup()' callback is invoked. Make
sure to implement proper routing management at link setup time, to route
the selected video stream to the desired TX output.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Both the AFE and HDMI s_stream routines (adv748x_afe_s_stream() and
adv748x_hdmi_s_stream()) have to enable the CSI-2 TX they are streaming video
data to.
With the introduction of dynamic routing between HDMI and AFE entities to
TXA, the video stream sink needs to be set at run time, and not statically
selected as the s_stream functions are currently doing.
To fix this, store a reference to the active CSI-2 TX sink for both HDMI and
AFE sources, and operate on it when starting/stopping the stream.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The power_up_tx() procedure needs to set a few registers conditionally to
the selected video source, but it currently checks for the provided tx to
be either TXA or TXB.
With the introduction of dynamic routing between HDMI and AFE entities to
TXA, checking which TX the function is operating on is not meaningful anymore.
To fix this, store the subdevice of the source providing video data to the
CSI-2 TX in the 'struct adv748x_csi2' representing the TX and check on it.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748x chip supports routing AFE output to either TXA or TXB.
In order to support run-time configuration of video stream path, create an
additional (not enabled) "AFE:8->TXA:0" link, and remove the IMMUTABLE flag
from existing ones.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add small is_txb() macro to the existing is_txa() and use it where
appropriate.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set initial try format with default configuration instead of current one.
Fixes: 8d3b307a15 ("media: ov2640: make VIDIOC_SUBDEV_G_FMT ioctl work with V4L2_SUBDEV_FORMAT_TRY")
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This function prints an error message on success. I don't have the
hardware, I just noticed this while reading the code.
Fixes: 8b99312b72 ("[media] Add v4l2 subdev driver for S5K4ECGX sensor")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver sets initial frame width and height to 0x0, which is invalid.
So set it to selection rectangle bounds instead.
This is detected by v4l2-compliance detected.
Cc: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver doesn't set all members of mbus format field when the
VIDIOC_SUBDEV_{S,G}_FMT ioctls are called.
This is detected by v4l2-compliance.
Cc: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VIDIOC_SUBDEV_G_FMT ioctl for this driver doesn't recognize
V4L2_SUBDEV_FORMAT_TRY and always works as if V4L2_SUBDEV_FORMAT_ACTIVE
is specified.
Cc: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver doesn't set all members of mbus format field when the
VIDIOC_SUBDEV_{S,G}_FMT ioctls are called.
This is detected by v4l2-compliance.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VIDIOC_SUBDEV_G_FMT ioctl for this driver doesn't recognize
V4L2_SUBDEV_FORMAT_TRY and always works as if V4L2_SUBDEV_FORMAT_ACTIVE
is specified.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Register a sub-device to the asynchronous subdevice framework, and also
create subdevice device node.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Create a source pad and set the media controller type to the sensor.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove remaining soc_camera specific code and drop soc_camera dependency
from this driver.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Switch s_power() callback to runtime PM framework. This also removes
soc_camera specific power management code and introduces reset and standby
gpios instead.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce multi_reg_write() to write multiple registers to the device and
use it where possible.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Replace GPL license statements with SPDX license identifiers (GPL-2.0).
This also fixes MODULE_LICENSE() ident to match the actual license text.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Copy the soc_camera based driver in v4l2 sensor driver directory.
This commit just copies the original file without modifying it.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We use put_unaligned_be16() to be simplified for setting register address
in ov8856_read_reg() and use sizeof() to be better suited for bytes
copying.
Signed-off-by: Ben Kao <ben.kao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This provides more power saving when the sensor is off.
While at that, do the delay on power/clock enable even if the sensor driver
itself doesn't control the GPIOs. This is required for the OLPC XO-1
platform, that lacks the proper power/reset properties in its DT, but
needs the delay after the sensor is clocked up.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The commit 71862f63f3 ("media: ov7670: Add the ov7670_s_power function")
added a power control routing. However, it was not good enough to use as
a s_power() callback: it merely flipped on the power GPIOs without
restoring the register settings.
Fix this now and register an actual power callback.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This will allow us to restore the last set frame rate after the device
returns from a power off.
[sakari.ailus@linux.intel.com>: Wrap a line over 80 characters]
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This will allow us to restore the last set format after the device returns
from a power off.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of assigning the return value to ret and then checking and
returning it, just return the value to the caller directly. The success
value is always 0.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds driver for Omnivision's ov8856 sensor,
the driver supports following features:
- manual exposure/gain(analog and digital) control support
- two link frequencies
- VBLANK/HBLANK support
- test pattern support
- media controller support
- runtime PM support
- enable Vsync signal output
- supported resolutions
+ 3280x2464 at 30FPS
+ 1640x1232 at 30FPS
Signed-off-by: Ben Kao <ben.kao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
imx274_read_reg() is not used since commit ca017467c7 ("media:
imx274: add helper to read multibyte registers").
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Switch to devm_kzalloc() when allocating the adv748x device struct.
The sizeof() is updated to determine the correct allocation size from
the dereferenced pointer type rather than hardcoding the struct type.
[Kieran: Change sizeof() to dereference the pointer type]
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add initial support for MLX90640 thermal cameras which output an 32x24
greyscale pixel image along with 2 rows of coefficent data.
Because of this the data outputed is really 32x26 and needs the two rows
removed after using the coefficent information to generate processed
images in userspace.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver got converted to not depend on soc_camera in commit
7b20f325a5 ("media: i2c: tw9910: Remove soc_camera dependencies").
There's no sense in keeping the old version there.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver got converted to not depend on soc_camera in commit
762c28121d ("media: i2c: ov772x: Remove soc_camera dependencies").
There's no sense in keeping the old version there.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver got converted to not depend on soc_camera in commit
6a26f141bf ("media: i2c: mt9t112: Remove soc_camera dependencies").
There's no sense in keeping the old version there.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the tw9910 subdevice is registered through the v4l2-async framework,
use the v4l2-async provided function to register it.
Fixes: 7b20f325a5 ("media: i2c: tw9910: Remove soc_camera dependencies")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver got converted to not depend on soc_camera on commit
57b0ad9ebe ("media: soc_camera: ov9640: move ov9640 out of soc_camera").
There's no sense on keeping the old version there.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jian Xu has left the company. Remove his e-mail address that no longer
works.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some little style fixup work.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Control handlers registration lacked error path with
v4l2_ctrl_handler_free() call. Fix it by using goto to alread existing
v4l2_ctrl_handler_free() call.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
An array which defines sensor's supported formats is not written anywhere,
so it can be constant.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some returns were adjoined to unrelated code blocks. This patch adds
a space inbetween.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver uses variables to store frame resolutions and to indexing
various arrays. These should be unsigned.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add missing SPDX identifiers to .c and .h files of the sensor driver.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch removes the dependency on an obsoleted soc_camera from ov9640
driver and changes the code to be a standalone v4l2 async subdevice.
It also adds GPIO allocations for power and reset signals (as they are not
handled by soc_camera now).
The values for waiting on GPIOs (reset and power) settling down were taken
from the datasheet (> 1 ms after HW/SW reset). The upper limit was chosen
as an arbitrary value. Also one occurrence of mdelay() was changed to
msleep(). The delays were successfully tested on a real hardware.
The patch makes ov9640 sensor again compatible with the pxa_camera driver.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Initial part of ov9640 transition from soc_camera subsystem to a standalone
v4l2 subdevice. The soc_camera version seems to be used only in Palm Zire72
and in (the future) HTC Magician. On these two devices the support is
broken as pxa_camera driver doesn't use soc_camera anymore. The other
mentions from git grep are "TODOs" (in board-osk.c) or chip names for
unsupported sensors on HW which doesn't use soc_camera at all (irelevant).
Copy the driver files from soc_camera and mark the original ones in the
Kconfig description as obsoleted.
Add config option VIDEO_OV9640 to the build files in drivers/media/i2c.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The following commits:
commit f6dd927f34 ("[media] media: ov7670: calculate framerate properly for ov7675")
commit 04ee6d9204 ("[media] media: ov7670: add possibility to bypass pll for ov7675")
introduced the ability to bypass PLL multiplier and use input clock (xvclk)
as pixel clock output frequency for ov7675 sensor.
PLL is bypassed using register DBLV[7:6], according to ov7670 and ov7675
sensor manuals. Macros used to set DBLV register seem wrong in the
driver, as their values do not match what reported in the datasheet.
Fix by changing DBLV_* macros to use bits [7:6] and set bits [3:0] to
default 0x0a reserved value (according to datasheets).
While at there, remove a write to DBLV register in
"ov7675_set_framerate()" that over-writes the previous one to the same
register that takes "info->pll_bypass" flag into account instead of setting PLL
multiplier to 4x unconditionally.
And, while at there, since "info->pll_bypass" is only used in
set/get_framerate() functions used by ov7675 only, it is not necessary
to check for the device id at probe time to make sure that when using
ov7670 "info->pll_bypass" is set to false.
Fixes: f6dd927f34 ("[media] media: ov7670: calculate framerate properly for ov7675")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver doesn't set all members of mbus format field when the
VIDIOC_SUBDEV_{S,G}_FMT ioctls are called.
This is detected by v4l2-compliance.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VIDIOC_SUBDEV_G_FMT ioctl for this driver doesn't recognize
V4L2_SUBDEV_FORMAT_TRY and always works as if V4L2_SUBDEV_FORMAT_ACTIVE
is specified.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set default window and format code at probe time instead of always checking
if they have not been set yet when VIDIOC_SUBDEV_G_FMT ioctl is called.
This change simplifies the next patch (make VIDIOC_SUBDEV_G_FMT ioctl work
with V4L2_SUBDEV_FORMAT_TRY).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The description of test patterns 11 and 12 are swapped.
Checked against the live sensor.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver fixed the TXA CSI-2 transmitter in 4-lane mode while it could
operate using 1-, 2- and 4-lanes. Update the driver to support all
available modes.
The driver makes use of large tables of static register/value writes
when powering up/down the TXA and TXB transmitters which include the
write to the NUM_LANES register. By converting the tables into functions
and using parameters the power up/down functions for TXA and TXB power
up/down can be merged and used for both transmitters.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The adv748x CSI-2 transmitters TXA and TXB can use different number of
lanes to transmit data. In order to be able to configure the device
correctly this information need to be parsed from device tree and stored
in each TX private data structure.
TXA supports 1, 2 and 4 lanes while TXB supports 1 lane.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Extend the MIPI CSI-2 power up sequence to match the power up sequence
in the hardware manual chapter "9.5.1 Power Up Sequence". This change
allows the power up functions to be reused when initializing the
hardware reducing code duplicating as well aligning with the
documentation.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
tw9910 driver tries to sleep for the same period of time
after each gpiod_set_value(). The patch moves duplicated code
to a helper function.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If gpiod_get_optional() fails in tw9910_power_on(), clk is left undisabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----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=G3om
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"First set of media patches contains:
- Three new platform drivers: aspeed-video seco-sed and sun5i-csi;
- One new sensor driver: imx214;
- Support for Xbox DVD Movie Playback kit remote controller;
- Removal of the legacy friio driver. The functionalities were ported
to another driver, already merged;
- New staging driver: Rockchip VPU;
- Added license text or SPDX tags to all media documentation files;
- Usual set of cleanup, fixes and enhancements"
* tag 'media/v4.20-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (263 commits)
media: cx23885: only reset DMA on problematic CPUs
media: ddbridge: Move asm includes after linux ones
media: drxk_hard: check if parameter is not NULL
media: docs: fix some GPL licensing ambiguity at the text
media: platform: Add Aspeed Video Engine driver
media: dt-bindings: media: Add Aspeed Video Engine binding documentation
media: vimc: fix start stream when link is disabled
media: v4l2-device: Link subdevices to their parent devices if available
media: siano: Use kmemdup instead of duplicating its function
media: rockchip vpu: remove some unused vars
media: cedrus: don't initialize pointers with zero
media: cetrus: return an error if alloc fails
media: cedrus: Add device-tree compatible and variant for A64 support
media: cedrus: Add device-tree compatible and variant for H5 support
media: dt-bindings: media: cedrus: Add compatibles for the A64 and H5
media: video-i2c: check if chip struct has set_power function
media: video-i2c: support runtime PM
media: staging: media: imx: Use of_node_name_eq for node name comparisons
media: v4l2-subdev: document controls need _FL_HAS_DEVNODE
media: vivid: Improve timestamping
...
Not all future supported video chips will always have power management
support, and so it is important to check before calling set_power() is
defined.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
AMG88xx has a register for setting operating mode. This adds support
runtime PM by changing the operating mode.
The instruction for changing sleep mode to normal mode is from the
reference specifications.
https://docid81hrs3j1.cloudfront.net/medialibrary/2017/11/PANA-S-A0002141979-1.pdf
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The autoexposure setup in the 1080p init array is redundant with the
default value of the sensor.
Remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now that we have everything in place to compute the clock rate at runtime,
we can enable the 60fps framerate for the mode we tested it with.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The current code uses an algorithm to clamp the FPS values and round them
to the closest supported one that isn't really allows to be extended to
more than two values.
Rework it a bit to make it much easier to extend the amount of FPS options
we support.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the ov5640_try_frame_interval function, the ret variable actually holds
the frame rate index to use, which is represented by the enum
ov5640_frame_rate in the driver.
Make it more obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now that we have moved the clock generation logic out of the bytes array,
these arrays are identical between the 15fps and 30fps variants.
Remove the duplicate entries, and convert the code accordingly.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The pixel clock rates were introduced to report the initially static clock
rate.
Since this is now handled dynamically, we can remove them entirely.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The MIPI divider is also cleared as part of the clock setup sequence, so we
can remove that code.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The OV5640_SCLK2X_ROOT_DIVIDER_DEFAULT and OV5640_SCLK_ROOT_DIVIDER_DEFAULT
defines represent exactly the same setup, and are at the same value, than
the more consistent with the rest of the driver OV5640_SCLK2X_ROOT_DIV and
OV5640_SCLK_ROOT_DIV.
Remove them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Part of the hardcoded initialization sequence is to set up the proper clock
dividers. However, this is now done dynamically through proper code and as
such, the static one is now redundant.
Let's remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The clock structure for the PCLK is quite obscure in the documentation, and
was hardcoded through the bytes array of each and every mode.
This is troublesome, since we cannot adjust it at runtime based on other
parameters (such as the number of bytes per pixel), and we can't support
either framerates that have not been used by the various vendors, since we
don't have the needed initialization sequence.
We can however understand how the clock tree works, and then implement some
functions to derive the various parameters from a given rate. And now that
those parameters are calculated at runtime, we can remove them from the
initialization sequence.
The modes also gained a new parameter which is the clock that they are
running at, from the register writes they were doing, so for now the switch
to the new algorithm should be transparent.
Co-Developed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The set_fmt operations updates the sensor format only when the image format
is changed. When only the image sizes gets changed, the format do not get
updated causing the sensor to always report the one that was previously in
use.
Without this patch, updating frame size only fails:
[fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:srgb xfer:srgb ...]
With this patch applied:
[fmt:UYVY8_2X8/1024x768@1/30 field:none colorspace:srgb xfer:srgb ...]
Fixes: 6949d86477 ("media: ov5640: do not change mode if format or frame interval is unchanged")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6 w/ CSI2 interface on 4.19.6 and 4.20-RC5
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The chip can be configured to output data transitions on the
rising or falling edge of PIXCLK (Datasheet R58:1[9]), default is on the
falling edge.
Parsing the fw-node is made in a subfunction to bundle all (future)
dt-parsing / fw-parsing stuff.
[m.grzeschik@pengutronix.de: Fix inverting clock. INV_PIX_CLOCK bit is set
per default. Set bit to 0 (enable mask bit without value) to enable
falling edge sampling.]
[m.felsch@pengutronix.de: use fwnode helpers]
[m.felsch@pengutronix.de: mv fw parsing into own function]
[m.felsch@pengutronix.de: adapt commit msg]
[sakari.ailus@linux.intel.com: V4L2 API usage changes to compile
on media tree master]
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch implements the framerate selection using the skipping and
readout power-modi features. The power-modi cut the framerate by half
and each context has an independent selection bit. The same applies to
the 2x skipping feature.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently set_fmt don't care about the streaming status, so the format
can be changed during streaming. This can lead into wrong behaviours.
Check if the device is already streaming and return -EBUSY to avoid
wrong behaviours.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add callback to check if we are already streaming. Now other callbacks
can check the state and return -EBUSY if we already streaming.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The imx274 driver uses regmap and the build will fail without it.
Fixes:
drivers/media/i2c/imx274.c:142:21: error: variable ‘imx274_regmap_config’ has initializer but incomplete type
static const struct regmap_config imx274_regmap_config = {
^~~~~~~~~~~~~
drivers/media/i2c/imx274.c:1869:19: error: implicit declaration of function ‘devm_regmap_init_i2c’ [-Werror=implicit-function-declaration]
imx274->regmap = devm_regmap_init_i2c(client, &imx274_regmap_config);
^~~~~~~~~~~~~~~~~~~~
and others.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_ctrl_handler_init() expects a hint of how many controls this
handler is expected to refer to. Since this number here is always 4,
let's pass exactly 4.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
imx274_read_reg() takes a u8 pointer ("reg") and casts it to pass it
to regmap_read(), which takes an unsigned int pointer. This results in
a corrupted stack and random crashes.
Fixes: 0985dd306f ("media: imx274: V4l2 driver for Sony imx274 CMOS sensor")
Cc: stable@vger.kernel.org # for 4.15 and up
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some Sony camera sensors have same test pattern
definitions, this patch unify the pattern naming
to make it more clear to the userspace.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
current imx355 test pattern order in ctrl menu
is not correct, this patch fixes it.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
current imx319 test pattern order in ctrl menu
is not correct, this patch fixes it.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 37c65802e76a ("media: tvp5150: Add sync lock interrupt handling")
introduced the interrupt handling. But we have to free the
v4l2_ctrl_handler before we can return the error code.
Fixes: 37c65802e76a ("media: tvp5150: Add sync lock interrupt handling")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is a spelling mistake in the module description as well
as a comment. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On older Kernels (prior to 4.15) irqreturn_t and devm_request_threaded_irq
is not defined when compiling adv7604.c. It seems more recent Kernels
include it via another header which is included by adv7604.c.
Now we include linux/interrupt.h explicitly to get the type also defined
for Kernels prior to 4.15.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The adv7180 produces 1 to 2 frames of garbage before proper sync is
established. This allows V4L2 drivers and apps to skip those.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Without CONFIG_HDMI, we get a link error for this driver:
drivers/media/i2c/tda1997x.o: In function `tda1997x_parse_infoframe':
tda1997x.c:(.text+0x2195): undefined reference to `hdmi_infoframe_unpack'
tda1997x.c:(.text+0x21b6): undefined reference to `hdmi_infoframe_log'
drivers/media/i2c/tda1997x.o: In function `tda1997x_log_infoframe':
tda1997x.c:(.text.unlikely+0x13d3): undefined reference to `hdmi_infoframe_unpack'
tda1997x.c:(.text.unlikely+0x1426): undefined reference to `hdmi_infoframe_log'
All other drivers in this directory that use HDMI select CONFIG_HDMI,
so do the same here:
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlv7H/seHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhasH/AvNibkzTAPQR7jE
r/R7NIaFUdPpaHYpLpoYIdSWkqpeWtN3q4eldJKWcpFCaE83EzDVu1PRw79rt/lm
JIYbZ2SZWbTB7d2TLEiEF2bFXr+OF8MVc1tSAsP5xTMvV6mIz7+i2xr9R0D4YrKY
ejd+ExF3HimuRf557Uey1MGsRIhedHsHjHbWjvR1MuKzvUv9nAL+1E2KJbfPXacp
LGXElCYcPXoKw+GxMS7C28idgLoEJoS/eVieRiMGsGlgEe/MuaNMU+GRLMde9lI0
c/G/4uumJTHVY7npOjuNt1+2FoLVt8oLlhPcB06R7FIwJN+TupLQifqBkIe2saT6
R6ExonQ=
=+/RR
-----END PGP SIGNATURE-----
Merge v4.20-rc4 into drm-next
Requested by Boris Brezillon for some vc4 fixes that are needed for future vc4 work.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The v4l2_dv_timings_cap struct is used to do sanity checks when setting and
enumerating DV timings, ensuring that only valid timings as per the HW
capabilities are allowed.
However, many drivers just filled in 0 for the minimum width, height or
pixelclock frequency. This can cause timings with e.g. 0 as width and height
to be accepted, which will in turn lead to a potential division by zero.
Fill in proper values are minimum boundaries. 640x350 was chosen since it is
the smallest resolution in v4l2-dv-timings.h. Same for 13 MHz as the lowest
pixelclock frequency (it's slightly below the minimum of 13.5 MHz in the
v4l2-dv-timings.h header).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CEC IP is very similar between the three HDMI receivers, but
not identical. Add support for all three variants.
Tested with an adv7604 and an adv7612.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Swapping the order between v4l2 subdevice registration and checking chip
id in b7a417628a ("media: ov2680: don't register the v4l2 subdevice
before checking chip ID") makes the mode restore to use the sensor
controls before they are set, so move the mode restore call to s_power
after the handler setup for controls is done.
This remove also the need for the error code path in power on function.
Fixes: b7a417628a ("media: ov2680: don't register the v4l2 subdevice before checking chip ID")
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for ov7670's v4l2 controls.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for ov5640's v4l2 controls.
Cc: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for ov2640's v4l2 controls.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov2640 has the test pattern generator features. This makes use of
it through V4L2_CID_TEST_PATTERN control.
[Sakari Ailus: Use "Eight Vertical Colour Bars" as the second manu entry]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The mt9m111 has special camera effects feature. This makes use of
it through V4L2_CID_COLORFX control.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds log_status ioctl and event interface for mt9m111's v4l2 controls.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
change bayer order when using test pattern mode.
remove test pattern mapping method
[Sakari Ailus: Drop extra added newline]
Signed-off-by: Chen, JasonX Z <jasonx.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clang warns when a variable is assigned to itself:
drivers/media/i2c/imx214.c:695:13: error: explicitly assigning value of
variable of type 'const struct reg_8 *' to itself
[-Werror,-Wself-assign]
for (table = table; table->addr != IMX214_TABLE_END ; table++) {
~~~~~ ^ ~~~~~
1 error generated.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vb2_ops structure can be const as it is only stored in the ops
field of a vb2_queue structure and this field is const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
AMG88xx has a register for setting frame rate 1 or 10 FPS.
This adds support changing frame interval.
Reference specifications:
https://docid81hrs3j1.cloudfront.net/medialibrary/2017/11/PANA-S-A0002141979-1.pdf
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use regmap for i2c register access. This simplifies register accesses and
chooses suitable access commands based on the functionality that the
adapter supports.
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The video device release() callback for video-i2c driver frees the whole
struct video_i2c_data. If there is no user left for the video device
when video_unregister_device() is called, the release callback is executed.
However, in video_i2c_remove() some fields (v4l2_dev, lock, and queue_lock)
in struct video_i2c_data are still accessed after video_unregister_device()
is called.
This fixes the use after free by moving the code from video_i2c_remove()
to the release() callback.
Fixes: 5cebaac609 ("media: video-i2c: add video-i2c driver")
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=UV0m
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-11-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21, part 1:
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/be7ebd91-edd9-8fa4-4286-1c57e3165113@linux.intel.com
The fields of a v4l2_subdev_ops structure are all const, so the
structures that are stored there and are not used elsewhere can be
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_ctrl_ops structure is only passed as the second argument to
functions such as v4l2_ctrl_new_std for which the corresponding
parameter is const, so make the v4l2_ctrl_ops structure const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a V4L2 sub-device driver for the Sony IMX214 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
Tested on a DB820c alike board with Intrinsyc Open-Q 13MP camera.
[Sakari Ailus: squash exposure time max limit patch]
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clang warns when a variable is assigned to itself.
drivers/media/i2c/tc358743.c:1921:7: warning: explicitly assigning value
of variable of type 'int' to itself [-Wself-assign]
ret = ret;
~~~ ^ ~~~
1 warning generated.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
4.19 is out, Lyude asked for a backmerge, and it's been a while. All
very good reasons on their own :-)
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Those drivers are part of the legacy SoC camera framework.
They're being converted to not use it, but sometimes we're
keeping both legacy any new driver.
This time, for example, we have two drivers on media with
the same name: ov772x. That's bad.
So, in order to prevent that to happen, let's prepend the SoC
legacy drivers with soc_.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_async_unregister_subdev() may not be called without
v4l2_async_register_subdev() being called first. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If probe fails, the kernel will print the error code. There's no need to
driver to do that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fixed the case where v4l2_async_unregister_subdev()
is called unnecessarily in the error handling path
in probe function.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When there is no EDID the CEC adapter should be unconfigured as
well. So call cec_phys_addr_invalidate() when this happens.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When there is no EDID the CEC adapter should be unconfigured as
well. So call cec_phys_addr_invalidate() when this happens.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changing framerate right before streamon had no effect,
the new framerate value was taken into account only at
next streamon, fix this.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the "xclk" clock was added, it was made mandatory. This broke the
driver on an OLPC plaform which doesn't know such clock. Make it
optional.
Tested on a OLPC XO-1 laptop.
Fixes: 0a024d634c ("[media] ov7670: get xclk")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The regmap change causes multiple warnings like
drivers/media/i2c/ov9650.c: In function 'ov965x_g_volatile_ctrl':
drivers/media/i2c/ov9650.c:889:29: error: 'reg2' may be used uninitialized in this function [-Werror=maybe-uninitialized]
exposure = ((reg2 & 0x3f) << 10) | (reg1 << 2) |
~~~~~~~~~~~~~~~^~~~~~
It is apparently hard for the compiler to see here if ov965x_read()
returned successfully or not. Besides, we have a v4l2_dbg() statement
that prints an uninitialized value if regmap_read() fails.
Adding an 'else' clause avoids the ambiguity.
Fixes: 361f3803ad ("media: ov9650: use SCCB regmap")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Function alignments are off by 1 space, as reported by
checkpatch.pl --strict.
Fix those.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a v4l2 sub-device driver for the Sony imx355 image sensor.
This is a camera sensor using the i2c bus for control and the
csi-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- 4 test patterns control support
- vflip/hflip control support (will impact the output bayer order)
- support following resolutions:
- 3268x2448, 3264x2448, 3280x2464 @ 30fps
- 1940x1096, 1936x1096, 1924x1080, 1920x1080 @ 60fps
- 1640x1232, 1640x922, 1300x736, 1296x736,
1284x720, 1280x720 820x616 @ 120fps
- support 4 bayer orders output (via change v/hflip)
- SRGGB10(default), SGRBG10, SGBRG10, SBGGR10
[Sakari Ailus: Use do_div() for dividing 64-bit numbers, fix fwnode if usage]
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Function alignments are off by 1 space, as reported by
checkpatch.pl --strict.
Fix those.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a v4l2 sub-device driver for the Sony imx319 image sensor.
This is a camera sensor using the i2c bus for control and the
csi-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- 4 test patterns control support
- vflip/hflip control support (will impact the output bayer order)
- support following resolutions:
- 3264x2448, 3280x2464 @ 30fps
- 1936x1096, 1920x1080 @ 60fps
- 1640x1232, 1640x922, 1296x736, 1280x720 @ 120fps
- support 4 bayer orders output (via change v/hflip)
- SRGGB10(default), SGRBG10, SGBRG10, SBGGR10
[Sakari Ailus: Replace 64-bit division by do_div(), fix fwnode if usage]
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of opportunistically trying to gather some information from the
V4L2 endpoint, set the bus type and let the V4L2 fwnode framework figure
out the configuration.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Initialise the V4L2 fwnode endpoints to zero in all drivers using
v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint
flags as well as the bus type. Setting bus type to zero will continue to
guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of allocating the V4L2 fwnode endpoint in
v4l2_fwnode_endpoint_alloc_parse, let the caller to do this. This allows
setting default parameters for the endpoint which is a very common need
for drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media
bus enum.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The adv748x assumes input endpoints are always enabled, and registers
a subdevice for each of them when the corresponding output subdevice
is registered.
Fix this by conditionally registering the input subdevice only if it is
actually described in device tree.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748x has two CSI-2 output port and one TTL input/output port for
digital video reception/transmission. The TTL digital pad is unconditionally
enabled during the device reset even if not used. Same goes for the TXA
and TXB CSI-2 outputs, which are enabled by the initial settings blob
programmed into the chip.
In order to improve power saving, do not enable unused output interfaces:
keep TTL output disabled, as it is not used, and drop CSI-2 output enabling
from the initial settings list, as they get conditionally enabled later.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the driver is now allowed to probe with a single output endpoint,
power management routines shall now take into account the case a CSI-2 TX
is not enabled.
Unify the adv748x_tx_power() routine to handle transparently TXA and TXB,
and enable the CSI-2 outputs conditionally.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the adv748x driver will fail to probe unless both of its
output endpoints (TXA and TXB) are connected.
Make the driver support probing provided that there is at least one
input, and one output connected and protect the clean-up function from
accessing un-initialized fields.
Following patches will fix other uses of un-initialized TXs in the driver,
such as power management functions.
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This can be done with c99 initializers, which makes the code cleaner
and more transparent. It does require gcc 4.6, because of this bug
in earlier versions:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676
Since commit cafa0010cd ("Raise the minimum required gcc version to
4.6"), this is the case.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The loop seemed to be made to calculate max, but max is not used in that
function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Change 720p JPEG mode to mode 3 as per other resolutions.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2 sub-device API does not support the crop default target. A number
of drivers apparently still did support this, likely as it was needed by
the SoC camera framework. Drop support for the default crop rectaingle in
sub-device drivers, and use the bounds rectangle in SoC camera instead.
Reported-by: Helmut Grohne <h.grohne@intenta.de>
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A number of sub-device drivers used a static name for the sub-device, and
thus the media entity. As the entity name must be unique within a media
device, this makes it impossible to have more than one instance of each
device in a media device. This is a rather severe limitation.
Instead of fixing these drivers, add a comment to the drivers noting that
such static names may not be used in the future.
The alternative of fixing the drivers is troublesome as the entity (as
well as sub-device) name is part of the uAPI. Changing that is almost
certain to break something. As these devices are old but no-one has
encountered a problem with the static names, leave it as-is.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
