There are two problems with the current code that have been highlighted
with the AQL feature that is now enbaled by default.
First problem is in ieee80211_rx_h_mesh_fwding(),
ieee80211_select_queue_80211() is used on received packets to choose
the sending AC queue of the forwarding packet although this function
should only be called on TX packet (it uses ieee80211_tx_info).
This ends with forwarded mesh packets been sent on unrelated random AC
queue. To fix that, AC queue can directly be infered from skb->priority
which has been extracted from QOS info (see ieee80211_parse_qos()).
Second problem is the value of queue_mapping set on forwarded mesh
frames via skb_set_queue_mapping() is not the AC of the packet but a
hardware queue index. This may or may not work depending on AC to HW
queue mapping which is driver specific.
Both of these issues lead to improper AC selection while forwarding
mesh packets but more importantly due to improper airtime accounting
(which is done on a per STA, per AC basis) caused traffic stall with
the introduction of AQL.
Fixes: cf44012810 ("mac80211: fix unnecessary frame drops in mesh fwding")
Fixes: d3c1597b8d ("mac80211: fix forwarded mesh frame queue mapping")
Co-developed-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://lore.kernel.org/r/20220214173214.368862-1-nico.escande@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 set capability NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211
to upper layer by default. That means we should pass EAPoL packets through
nl80211 path only, and should not send the EAPoL skb to netdevice diretly.
At the meanwhile, wpa_supplicant would not register sock to listen EAPoL
skb on the netdevice.
However, there is no control_port_protocol handler in mac80211 for 802.3 RX
packets, mac80211 driver would pass up the EAPoL rekey frame to netdevice
and wpa_supplicant would be never interactive with this kind of packets,
if SUPPORTS_RX_DECAP_OFFLOAD is enabled. This causes STA always rekey fail
if EAPoL frame go through 802.3 path.
To avoid this problem, align the same process as 802.11 type to handle
this frame before put it into network stack.
This also addresses a potential security issue in 802.3 RX mode that was
previously fixed in commit a8c4d76a8d ("mac80211: do not accept/forward
invalid EAPOL frames").
Cc: stable@vger.kernel.org # 5.12+
Fixes: 80a915ec44 ("mac80211: add rx decapsulation offload support")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Link: https://lore.kernel.org/r/6889c9fced5859ebb088564035f84fd0fa792a49.1644680751.git.deren.wu@mediatek.com
[fix typos, update comment and add note about security issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's currently only one driver that reports CHECKSUM_COMPLETE,
that is iwlwifi. The current hardware there calculates checksum
after the SNAP header, but only RFC 1042 (and some other cases,
but replicating the exact hardware logic for corner cases in the
driver seemed awkward.)
Newer generations of hardware will checksum _including_ the SNAP,
which makes things easier.
To handle that, simply always assume the checksum _includes_ the
SNAP header, which this patch does, requiring to first add it
for older iwlwifi hardware, and then remove it again later on
conversion.
Alternatively, we could have:
1) Always assumed the checksum starts _after_ the SNAP header;
the problem with this is that we'd have to replace the exact
"what is the SNAP" check in iwlwifi that cfg80211 has.
2) Made it configurable with some flag, but that seemed like too
much complexity.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.230736e19e0e.I3e6745873585ad943c152fab9e23b5221f17a95f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some AP can possibly try non-standard VHT rate and mac80211 warns and drops
packets, and leads low TCP throughput.
Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
WARNING: CPU: 1 PID: 7817 at net/mac80211/rx.c:4856 ieee80211_rx_list+0x223/0x2f0 [mac8021
Since commit c27aa56a72 ("cfg80211: add VHT rate entries for MCS-10 and MCS-11")
has added, mac80211 adds this support as well.
After this patch, throughput is good and iw can get the bitrate:
rx bitrate: 975.1 MBit/s VHT-MCS 10 80MHz short GI VHT-NSS 2
or
rx bitrate: 1083.3 MBit/s VHT-MCS 11 80MHz short GI VHT-NSS 2
Buglink: https://bugzilla.suse.com/show_bug.cgi?id=1192891
Reported-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20220103013623.17052-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* ndo_fill_forward_path support in mac80211, to let
drivers use it
* association comeback notification for userspace,
to be able to react more sensibly to long delays
* support for background radar detection hardware
in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
-----BEGIN PGP SIGNATURE-----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=u1jf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* ndo_fill_forward_path support in mac80211, to let drivers use it
* association comeback notification for userspace, to be able
to react more sensibly to long delays
* support for background radar detection hardware in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
Conflicts:
net/wireless/reg.c:
e08ebd6d7b ("cfg80211: Acquire wiphy mutex on regulatory work")
701fdfe348 ("cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface")
https://lore.kernel.org/r/20211221111950.57ecc6a7@canb.auug.org.au
drivers/net/wireless/ath/ath10k/wmi.c:
7f599aeccb ("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel")
3bf2537ec2 ("ath10k: drop beacon and probe response which leak from other channel")
https://lore.kernel.org/r/20211221115004.1cd6b262@canb.auug.org.au
* tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (32 commits)
cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface
rfkill: allow to get the software rfkill state
cfg80211: refactor cfg80211_get_ies_channel_number()
nl82011: clarify interface combinations wrt. channels
nl80211: Add support to offload SA Query procedures for AP SME device
nl80211: Add support to set AP settings flags with single attribute
mac80211: add more HT/VHT/HE state logging
cfg80211: Use the HE operation IE to determine a 6GHz BSS channel
cfg80211: rename offchannel_chain structs to background_chain to avoid confusion with ETSI standard
mac80211: Notify cfg80211 about association comeback
cfg80211: Add support for notifying association comeback
mac80211: introduce channel switch disconnect function
cfg80211: Fix order of enum nl80211_band_iftype_attr documentation
cfg80211: simplify cfg80211_chandef_valid()
mac80211: Remove a couple of obsolete TODO
mac80211: fix FEC flag in radio tap header
mac80211: use coarse boottime for airtime fairness code
ieee80211: change HE nominal packet padding value defines
cfg80211: use ieee80211_bss_get_elem() instead of _get_ie()
mac80211: Use memset_after() to clear tx status
...
====================
Link: https://lore.kernel.org/r/20211221112532.28708-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In mac80211, while building radiotap header
IEEE80211_RADIOTAP_MCS_HAVE_FEC flag is missing when LDPC enabled
from driver, hence LDPC is not updated properly in radiotap header.
Fix that by adding HAVE_FEC flag while building radiotap header.
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://lore.kernel.org/r/1638294648-844-2-git-send-email-quic_ppranees@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The codepaths for rx with decap offload and tx with itxq were not updating
the counters for the throughput led trigger.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211113063415.55147-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 8c89f7b3d3 ("mac80211: Use flex-array for radiotap header
bitmap") we accidentally pointed the position to the wrong place, so
we overwrite a present bitmap, and thus cause all kinds of trouble.
To see the issue, note that the previous code read:
pos = (void *)(it_present + 1);
The requirement now is that we need to calculate pos via it_optional,
to not trigger the compiler hardening checks, as:
pos = (void *)&rthdr->it_optional[...];
Rewriting the original expression, we get (obviously, since that just
adds "+ x - x" terms):
pos = (void *)(it_present + 1 + rthdr->it_optional - rthdr->it_optional)
and moving the "+ rthdr->it_optional" outside to be used as an array:
pos = (void *)&rthdr->it_optional[it_present + 1 - rthdr->it_optional];
The original is off by one, fix it.
Cc: stable@vger.kernel.org
Fixes: 8c89f7b3d3 ("mac80211: Use flex-array for radiotap header bitmap")
Reported-by: Sid Hayn <sidhayn@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sid Hayn <sidhayn@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20211109100203.c61007433ed6.I1dade57aba7de9c4f48d68249adbae62636fd98c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_get_keyid() will return false value if IV has been stripped,
such as return 0 for IP/ARP frames due to LLC header, and return -EINVAL
for disassociation frames due to its length... etc. Don't try to access
it if it's not present.
Signed-off-by: Xing Song <xing.song@mediatek.com>
Link: https://lore.kernel.org/r/20211101024657.143026-1-xing.song@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* the applicable eth_hw_addr_set() and const hw_addr changes
* various code cleanups/refactorings
* stack usage reductions across the wireless stack
* some unstructured find_ie() -> structured find_element()
changes
* a few more pieces of multi-BSSID support
* some 6 GHz regulatory support
* 6 GHz support in hwsim, for testing userspace code
* Light Communications (LC, 802.11bb) early band definitions
to be able to add a first driver soon
-----BEGIN PGP SIGNATURE-----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=ZXrI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Quite a few changes:
* the applicable eth_hw_addr_set() and const hw_addr changes
* various code cleanups/refactorings
* stack usage reductions across the wireless stack
* some unstructured find_ie() -> structured find_element()
changes
* a few more pieces of multi-BSSID support
* some 6 GHz regulatory support
* 6 GHz support in hwsim, for testing userspace code
* Light Communications (LC, 802.11bb) early band definitions
to be able to add a first driver soon
* tag 'mac80211-next-for-net-next-2021-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (35 commits)
cfg80211: fix kernel-doc for MBSSID EMA
mac80211: Prevent AP probing during suspend
nl80211: Add LC placeholder band definition to nl80211_band
...
====================
Link: https://lore.kernel.org/r/20211021154953.134849-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
WARNING: CPU: 1 PID: 9 at net/mac80211/sta_info.c:554
sta_info_insert_rcu+0x121/0x12a0
Modules linked in:
CPU: 1 PID: 9 Comm: kworker/u8:1 Not tainted 5.14.0-rc7+ #253
Workqueue: phy3 ieee80211_iface_work
RIP: 0010:sta_info_insert_rcu+0x121/0x12a0
...
Call Trace:
ieee80211_ibss_finish_sta+0xbc/0x170
ieee80211_ibss_work+0x13f/0x7d0
ieee80211_iface_work+0x37a/0x500
process_one_work+0x357/0x850
worker_thread+0x41/0x4d0
If an Ad-Hoc node receives packets with invalid source MAC address,
it hits a WARN_ON in sta_info_insert_check(), this can spam the log.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20210827144230.39944-1-yuehaibing@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce TWT action frames parsing support to mac80211.
Currently just individual TWT agreement are support in AP mode.
Whenever the AP receives a TWT action frame from an associated client,
after performing sanity checks, it will notify the underlay driver with
requested parameters in order to check if they are supported and if there
is enough room for a new agreement. The driver is expected to set the
agreement result and report it to mac80211.
Drivers supporting this have two new callbacks:
- add_twt_setup (mandatory)
- twt_teardown_request (optional)
mac80211 will send an action frame reply according to the result
reported by the driver.
Tested-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/257512f2e22ba42b9f2624942a128dd8f141de4b.1629741512.git.lorenzo@kernel.org
[use le16p_replace_bits(), minor cleanups, use (void *) casts,
fix to use ieee80211_get_he_iftype_cap() correctly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
The it_present member of struct ieee80211_radiotap_header is treated as a
flexible array (multiple u32s can be conditionally present). In order for
memcpy() to reason (or really, not reason) about the size of operations
against this struct, use of bytes beyond it_present need to be treated
as part of the flexible array. Add a trailing flexible array and
initialize its initial index via pointer arithmetic.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210806215305.2875621-1-keescook@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a monitor interface is present together with other interfaces, a
received skb is copied and received on the monitor netdev. Before, the
copied skb was allocated with exactly the amount of space needed for
the radiotap header, resulting in an skb without any headroom at all
being received on the monitor netdev. With the introduction of eBPF
and XDP in the kernel, skbs may be processed by custom eBPF programs.
However, since the skb cannot be reallocated in the eBPF program, no
more data or headers can be pushed. The old code made sure the final
headroom was zero regardless of the value of NET_SKB_PAD, so increasing
that constant would have no effect.
Now we allocate monitor skb copies with a headroom of NET_SKB_PAD bytes
before the radiotap header. Monitor interfaces now behave in the same
way as other netdev interfaces that honor the NET_SKB_PAD constant.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Link: https://lore.kernel.org/r/20210628123713.2070753-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This switches the airtime scheduler in mac80211 to use a virtual
time-based scheduler instead of the round-robin scheduler used before.
This has a couple of advantages:
- No need to sync up the round-robin scheduler in firmware/hardware with
the round-robin airtime scheduler.
- If several stations are eligible for transmission we can schedule both
of them; no need to hard-block the scheduling rotation until the head
of the queue has used up its quantum.
- The check of whether a station is eligible for transmission becomes
simpler (in ieee80211_txq_may_transmit()).
The drawback is that scheduling becomes slightly more expensive, as we
need to maintain an rbtree of TXQs sorted by virtual time. This means
that ieee80211_register_airtime() becomes O(logN) in the number of
currently scheduled TXQs because it can change the order of the
scheduled stations. We mitigate this overhead by only resorting when a
station changes position in the tree, and hopefully N rarely grows too
big (it's only TXQs currently backlogged, not all associated stations),
so it shouldn't be too big of an issue.
To prevent divisions in the fast path, we maintain both station sums and
pre-computed reciprocals of the sums. This turns the fast-path operation
into a multiplication, with divisions only happening as the number of
active stations change (to re-compute the current sum of all active
station weights). To prevent this re-computation of the reciprocal from
happening too frequently, we use a time-based notion of station
activity, instead of updating the weight every time a station gets
scheduled or de-scheduled. As queues can oscillate between empty and
occupied quite frequently, this can significantly cut down on the number
of re-computations. It also has the added benefit of making the station
airtime calculation independent on whether the queue happened to have
drained at the time an airtime value was accounted.
Co-developed-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210623134755.235545-1-toke@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to differentiate these frames since the ones we
currently put on the skb_queue_tdls_chsw have already
been converted to ethernet format, but now that we've
got a single place to enqueue to the sdata->skb_queue
this isn't hard. Just differentiate based on protocol
and adjust the code to queue the SKBs appropriately.
Link: https://lore.kernel.org/r/20210517230754.17034990abef.I5342f2183c0d246b18d36c511eb3b6be298a6572@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For some chips/drivers, e.g., QCA6174 with ath10k, the decryption is
done by the hardware, and the Protected bit in the Frame Control field
is cleared in the lower level driver before the frame is passed to
mac80211. In such cases, the condition for ieee80211_has_protected() is
not met in ieee80211_rx_h_defragment() of mac80211 and the new security
validation steps are not executed.
Extend mac80211 to cover the case where the Protected bit has been
cleared, but the frame is indicated as having been decrypted by the
hardware. This extends protection against mixed key and fragment cache
attack for additional drivers/chips. This fixes CVE-2020-24586 and
CVE-2020-24587 for such cases.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.037aa5ca0390.I7bb888e2965a0db02a67075fcb5deb50eb7408aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
EAPOL frames are used for authentication and key management between the
AP and each individual STA associated in the BSS. Those frames are not
supposed to be sent by one associated STA to another associated STA
(either unicast for broadcast/multicast).
Similarly, in 802.11 they're supposed to be sent to the authenticator
(AP) address.
Since it is possible for unexpected EAPOL frames to result in misbehavior
in supplicant implementations, it is better for the AP to not allow such
cases to be forwarded to other clients either directly, or indirectly if
the AP interface is part of a bridge.
Accept EAPOL (control port) frames only if they're transmitted to the
own address, or, due to interoperability concerns, to the PAE group
address.
Disable forwarding of EAPOL (or well, the configured control port
protocol) frames back to wireless medium in all cases. Previously, these
frames were accepted from fully authenticated and authorized stations
and also from unauthenticated stations for one of the cases.
Additionally, to avoid forwarding by the bridge, rewrite the PAE group
address case to the local MAC address.
Cc: stable@vger.kernel.org
Co-developed-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.cb327ed0cabe.Ib7dcffa2a31f0913d660de65ba3c8aca75b1d10f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As pointed out by Mathy Vanhoef, we implement the RX PN check
on fragmented frames incorrectly - we check against the last
received PN prior to the new frame, rather than to the one in
this frame itself.
Prior patches addressed the security issue here, but in order
to be able to reason better about the code, fix it to really
compare against the current frame's PN, not the last stored
one.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.bfbc340ff071.Id0b690e581da7d03d76df90bb0e3fd55930bc8a0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prior patches protected against fragmentation cache attacks
by coloring keys, but this shows that it can lead to issues
when multiple stations use the same sequence number. Add a
fragment cache to struct sta_info (in addition to the one in
the interface) to separate fragments for different stations
properly.
This then automatically clear most of the fragment cache when a
station disconnects (or reassociates) from an AP, or when client
interfaces disconnect from the network, etc.
On the way, also fix the comment there since this brings us in line
with the recommendation in 802.11-2016 ("An AP should support ...").
Additionally, remove a useless condition (since there's no problem
purging an already empty list).
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.fc35046b0d52.I1ef101e3784d13e8f6600d83de7ec9a3a45bcd52@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With old ciphers (WEP and TKIP) we shouldn't be using A-MSDUs
since A-MSDUs are only supported if we know that they are, and
the only practical way for that is HT support which doesn't
support old ciphers.
However, we would normally accept them anyway. Since we check
the MMIC before deaggregating A-MSDUs, and the A-MSDU bit in
the QoS header is not protected in TKIP (or WEP), this enables
attacks similar to CVE-2020-24588. To prevent that, drop A-MSDUs
completely with old ciphers.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.076543300172.I548e6e71f1ee9cad4b9a37bf212ae7db723587aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simultaneously prevent mixed key attacks (CVE-2020-24587) and fragment
cache attacks (CVE-2020-24586). This is accomplished by assigning a
unique color to every key (per interface) and using this to track which
key was used to decrypt a fragment. When reassembling frames, it is
now checked whether all fragments were decrypted using the same key.
To assure that fragment cache attacks are also prevented, the ID that is
assigned to keys is unique even over (re)associations and (re)connects.
This means fragments separated by a (re)association or (re)connect will
not be reassembled. Because mac80211 now also prevents the reassembly of
mixed encrypted and plaintext fragments, all cache attacks are prevented.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.3f8290e59823.I622a67769ed39257327a362cfc09c812320eb979@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not mix plaintext and encrypted fragments in protected Wi-Fi
networks. This fixes CVE-2020-26147.
Previously, an attacker was able to first forward a legitimate encrypted
fragment towards a victim, followed by a plaintext fragment. The
encrypted and plaintext fragment would then be reassembled. For further
details see Section 6.3 and Appendix D in the paper "Fragment and Forge:
Breaking Wi-Fi Through Frame Aggregation and Fragmentation".
Because of this change there are now two equivalent conditions in the
code to determine if a received fragment requires sequential PNs, so we
also move this test to a separate function to make the code easier to
maintain.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.30c4394bb835.I5acfdb552cc1d20c339c262315950b3eac491397@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The recent addition of in_serving_softirq() to kconv.h results in
compile failure on PREEMPT_RT because it requires
task_struct::softirq_disable_cnt. This is not available if kconv.h is
included from sched.h.
It is not needed to include kconv.h from sched.h. All but the net/ user
already include the kconv header file.
Move the include of the kconv.h header from sched.h it its users.
Additionally include sched.h from kconv.h to ensure that everything
task_struct related is available.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lkml.kernel.org/r/20210218173124.iy5iyqv3a4oia4vv@linutronix.de
This allows drivers to pass 802.3 frames to mac80211, with some restrictions:
- the skb must be passed with a valid sta
- fast-rx needs to be active for the sta
- monitor mode needs to be disabled
mac80211 will tell the driver when it is safe to enable rx decap offload for
a particular station.
In order to implement support, a driver must:
- call ieee80211_hw_set(hw, SUPPORTS_RX_DECAP_OFFLOAD)
- implement ops->sta_set_decap_offload
- mark 802.3 frames with RX_FLAG_8023
If it doesn't want to enable offload for some vif types, it can mask out
IEEE80211_OFFLOAD_DECAP_ENABLED in vif->offload_flags from within the
.add_interface or .update_vif_offload driver ops
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-6-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using WEP, the default unicast key needs to be selected, instead of
the STA PTK.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It should be !is_multicast_ether_addr() in ieee80211_rx_h_sta_process()
for the rx_stats update, below commit remove the !, this patch is to
change it back.
It lead the rx rate "iw wlan0 station dump" become invalid for some
scenario when IEEE80211_HW_USES_RSS is set.
Fixes: 09a740ce35 ("mac80211: receive and process S1G beacons")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/1607483189-3891-1-git-send-email-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commits
d3fd65484c ("net: core: add dev_sw_netstats_tx_add")
451b05f413 ("net: netdevice.h: sw_netstats_rx_add helper)
have added API to update net device per-cpu TX/RX stats.
Use core API instead of ieee80211_tx/rx_stats().
Signed-off-by: Lev Stipakov <lev@openvpn.net>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20201113214623.144663-1-lev@openvpn.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add KCOV remote annotations to ieee80211_iface_work() and
ieee80211_rx_list(). This will enable coverage-guided fuzzing of
mac80211 code that processes incoming 802.11 frames.
Signed-off-by: Aleksandr Nogikh <nogikh@google.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
S1G beacons are 802.11 Extension Frames, so the fixed
header part differs from regular beacons.
Add a handler to process S1G beacons and abstract out the
fetching of BSSID and element start locations in the
beacon body handler.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-14-thomas@adapt-ip.com
[don't rename, small coding style cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit finds the correct offset for Information
Elements in S1G beacon frames so they can be reported in
scan results.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-8-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling mod_timer for every rx/tx packet can be quite expensive.
Instead of constantly updating the timer, we can simply let it run out
and check the timestamp of the last ACK or rx packet to re-arm it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-9-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to unify the tx status path, the hw 802.11 encapsulation flag
needs to survive the trip to the tx status call.
Since we don't have any free bits in info->flags, we need to move one.
IEEE80211_TX_INTFL_NEED_TXPROCESSING is only used internally in mac80211,
and only before the call into the driver.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-10-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used to run mac80211 rx processing on a batch of frames in NAPI
poll before passing them to the network stack in a large batch.
This can improve icache footprint, or it can be used to pass frames via
netif_receive_skb_list.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200726110611.46886-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without this patch, eapol frames cannot be received in mesh
mode, when 802.1X should be used. Initially only a MGTK is
defined, which is found and set as rx->key, when there are
no other keys set. ieee80211_drop_unencrypted would then
drop these eapol frames, as they are data frames without
encryption and there exists some rx->key.
Fix this by differentiating between mesh eapol frames and
other data frames with existing rx->key. Allow mesh mesh
eapol frames only if they are for our vif address.
With this patch in-place, ieee80211_rx_h_mesh_fwding continues
after the ieee80211_drop_unencrypted check and notices, that
these eapol frames have to be delivered locally, as they should.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200625104214.50319-1-markus.theil@tu-ilmenau.de
[small code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the files:
- net/mac80211/rx.c
- net/wireless/Kconfig
the wiki url is still the old "wireless.kernel.org"
instead of the new "wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Link: https://lore.kernel.org/r/20200605154112.16277-10-f.suligoi@asem.it
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we receive management frames with an HT-Control field, we cannot
parse them properly, as we assume a fixed length management header.
Since we don't even need the HTC field (for these frames, or really
at all), just remove it at the beginning of RX.
Reported-by: Haggai Abramovsky <haggai.abramovsky@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200526143346.cf5ce70521c5.I333251a084ec4cfe67b7ef7efe2d2f1a33883931@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
