Implement the operations to set desired mode and retrieve the current
mode.
This feature was tested with an IP101G.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP101G provides three counters: RX packets, CRC errors and symbol
errors. The error counters can be configured to clear automatically on
read. Unfortunately, this isn't true for the RX packet counter. Because
of this and because the RX packet counter is more likely to overflow,
than the error counters implement only support for the error counters.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registers >= 16 are paged. Be sure to set the page. It seems this was
working for now, because the default is correct for the registers used
in the driver at the moment. But this will also assume, nobody will
change the page select register before linux is started. The page select
register is _not_ reset with a soft reset of the PHY.
To ease the function reuse between the non-paged register space of the
IP101A and the IP101G, add noop read_page()/write_page() callbacks so
the IP101G functions can also be used for the IP101A.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bit is reserved as 'always-write-1'. While this is not a particular
error, because we are only setting it, guard it by checking the model to
prevent errors in the future.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, the IP101A and IP101G share the same PHY identifier.
While most of the functions are somewhat backwards compatible, there is
for example the APS_EN bit on the IP101A but on the IP101G this bit
reserved. Also, the IP101G has many more functionalities.
Deduce the model by accessing the page select register which - according
to the datasheet - is not available on the IP101A. If this register is
writable, assume we have an IP101G.
Split the combined IP101A/G driver into two separate drivers.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY core already resets the PHY before .config_init() if a
.soft_reset() op is registered. Drop the open-coded ip1xx_reset().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't sometimes use the address operator and sometimes not. Drop it and
make the code look uniform.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the datasheet of the IP101A/G there is no revision field
and MII_PHYSID2 always reads as 0x0c54. Use PHY_ID_MATCH_EXACT() then.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simpify the initializations of the structures. There is no functional
change.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.
Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.
This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is nowhere used in the kernel. It also seems to be lacking the
proper fiber advertise flags. Remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_read_status() is already the default for the .read_status() op.
Drop the unnecessary references.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio_bus reset code first de-asserted the reset by allocating with
GPIOD_OUT_LOW, then asserted and de-asserted again. In other words, if
the reset signal defaulted to asserted, there'd be a short "spike"
before the reset.
Here is what happens depending on the pre-existing state of the reset
signal:
Reset (previously asserted): ~~~|_|~~~~|_______
Reset (previously deasserted): _____|~~~~|_______
^ ^ ^
A B C
At point A, the low going transition is because the reset line is
requested using GPIOD_OUT_LOW. If the line is successfully requested,
the first thing we do is set it high _without_ any delay. This is
point B. So, a glitch occurs between A and B.
We then fsleep() and finally set the GPIO low at point C.
Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
transitions. Instead we get:
Reset (previously asserted) : ~~~~~~~~~~|______
Reset (previously deasserted): ____|~~~~~|______
^ ^
A C
Where A and C are the points described above in the code. Point B
has been eliminated.
The issue was found when we pulled down the reset signal for the
Marvell 88E1512P PHY (because it requires at least 50ms after POR with
an active clock). Looking at the reset signal with a scope revealed a
short spike, point B in the artwork above.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210202143239.10714-1-mike.looijmans@topic.nl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Ubiquiti U-Fiber Instant SFP GPON module has nonsensical information
stored in its EEPROM. It claims to support all transceiver types including
10G Ethernet. Clear all claimed modes and set only 1000baseX_Full, which is
the only one supported.
This module has also phys_id set to SFF, and the SFP subsystem currently
does not allow to use SFP modules detected as SFFs. Add exception for this
module so it can be detected as supported.
This change finally allows to detect and use SFP GPON module Ubiquiti
U-Fiber Instant on Linux system.
EEPROM content of this SFP module is (where XX is serial number):
00: 02 04 0b ff ff ff ff ff ff ff ff 03 0c 00 14 c8 ???........??.??
10: 00 00 00 00 55 42 4e 54 20 20 20 20 20 20 20 20 ....UBNT
20: 20 20 20 20 00 18 e8 29 55 46 2d 49 4e 53 54 41 .??)UF-INSTA
30: 4e 54 20 20 20 20 20 20 34 20 20 20 05 1e 00 36 NT 4 ??.6
40: 00 06 00 00 55 42 4e 54 XX XX XX XX XX XX XX XX .?..UBNTXXXXXXXX
50: 20 20 20 20 31 34 30 31 32 33 20 20 60 80 02 41 140123 `??A
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The workaround for VSOL V2801F brand based GPON SFP modules added in commit
0d035bed2a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0
workaround") works only for IDs added explicitly to the list. Since there
are rebranded modules where OEM vendors put different strings into the
vendor name field, we cannot base workaround on IDs only.
Moreover the issue which the above mentioned commit tried to work around is
generic not only to VSOL based modules, but rather to all GPON modules
based on Realtek RTL8672 and RTL9601C chips.
These include at least the following GPON modules:
* V-SOL V2801F
* C-Data FD511GX-RM0
* OPTON GP801R
* BAUDCOM BD-1234-SFM
* CPGOS03-0490 v2.0
* Ubiquiti U-Fiber Instant
* EXOT EGS1
These Realtek chips have broken EEPROM emulator which for N-byte read
operation returns just the first byte of EEPROM data, followed by N-1
zeros.
Introduce a new function, sfp_id_needs_byte_io(), which detects SFP modules
with broken EEPROM emulator based on N-1 zeros and switch to 1 byte EEPROM
reading operation.
Function sfp_i2c_read() now always uses single byte reading when it is
required and when function sfp_hwmon_probe() detects single byte access,
it disables registration of hwmon device, because in this case we cannot
reliably and atomically read 2 bytes as is required by the standard for
retrieving values from diagnostic area.
(These Realtek chips are broken in a way that violates SFP standards for
diagnostic interface. Kernel in this case simply cannot do anything less
of skipping registration of the hwmon interface.)
This patch fixes reading of EEPROM content from SFP modules based on
Realtek RTL8672 and RTL9601C chips. Diagnostic interface of EEPROM stays
broken and cannot be fixed.
Fixes: 0d035bed2a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround")
Co-developed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SmartEEE for the atheros phy was deemed buggy by Freescale and commits
were added to disable it for their boards.
In initial testing, SolidRun found that the default settings were
causing disconnects but by increasing the Tw buffer time we could allow
enough time for all parts of the link to come out of a low power state
and function properly without causing a disconnect. This allows us to
have functional power savings of between 300 and 400mW, rather than
disabling the feature altogether.
This commit adds support for disabling SmartEEE and configuring the Tw
parameters for 1G and 100M speeds.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for 100Base-FX, 100Base-LX, 100Base-PX and 100Base-BX10 modules
This is needed for Sparx-5 switch.
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This bit is enabled by default and advertises support for extended
next page support. XNP is only needed for 10GBase-T and MultiGig
support which is not supported. Additionally, Cisco MultiGig switches
will read this bit and attempt 10Gb negotiation even though Next Page
support is disabled. This will cause timeouts when the interface is
forced to 100Mbps and auto-negotiation will fail. The interfaces are
only 1000Base-T and supporting auto-negotiation for this only requires
the Next Page bit to be set.
Taken from:
7406c5244b
and adapted to mainline kernels by rmk.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kzSdb-000417-FJ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add debugfs support to SFP so that the internal state of the SFP state
machines and hardware signal state can be viewed from userspace, rather
than having to compile a debug kernel to view state transitions in the
kernel log. The 'state' output looks like:
Module state: empty
Module probe attempts: 0 0
Device state: up
Main state: down
Fault recovery remaining retries: 5
PHY probe remaining retries: 12
moddef0: 0
rx_los: 1
tx_fault: 1
tx_disable: 1
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1kyYRe-0004kN-3F@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit bedd8d78ab ("net: phy: smsc: LAN8710/20: add phy refclk in
support") added the phy clk support. The commit already checks if
clk_get_optional() throw an error but instead of returning the error it
ignores it.
Fixes: bedd8d78ab ("net: phy: smsc: LAN8710/20: add phy refclk in support")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210111085932.28680-1-m.felsch@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert at803x_clk_out_config() to use phy_modify_mmd().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kyc72-0008Pq-1x@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the bitrate-derived support to include 2500BASE-X for modules
that report a bitrate of 2500Mbaud.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kyYQf-0004iY-Gh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SFP MSA defines two option bits in byte 65 to indicate how the
Rx_LOS signal on SFP pin 8 behaves:
bit 2 - Loss of Signal implemented, signal inverted from standard
definition in SFP MSA (often called "Signal Detect").
bit 1 - Loss of Signal implemented, signal as defined in SFP MSA
(often called "Rx_LOS").
Clearly, setting both bits results in a meaningless situation: it would
mean that LOS is implemented in both the normal sense (1 = signal loss)
and inverted sense (0 = signal loss).
Unfortunately, there are modules out there which set both bits, which
will be initially interpret as "inverted" sense, and then, if the LOS
signal changes state, we will toggle between LINK_UP and WAIT_LOS
states.
Change our LOS handling to give well defined behaviour: only interpret
these bits as meaningful if exactly one is set, otherwise treat it as
if LOS is not implemented.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kyYQa-0004iR-CU@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Switch to lockdep_assert_held(_once), similar to what is being done
in other subsystems. One advantage is that there's zero runtime
overhead if lockdep support isn't enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ccc40b9d-8ee0-43a1-5009-2cc95ca79c85@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM72116 features a 28nm integrated EPHY, add an entry to match this PHY
OUI.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210106170944.1253046-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KS8851 has a reduced internal PHY, which is accessible through its
registers at offset 0xe4. The PHY is compatible with KS886x PHY present
in Micrel switches, including the PHY ID Low/High registers swap, which
is present both in the MAC and the switch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not check the encoding when deriving 1000BASE-X from the bitrate
when no other modes are discovered. Some GPON modules (VSOL V2801F
and CarlitoxxPro CPGOS03-0490 v2.0) indicate NRZ encoding with a
1200Mbaud bitrate, but should be driven with 1000BASE-X on the host
side.
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a workaround for the detection of VSOL V2801F / CarlitoxxPro
CPGOS03-0490 v2.0 GPON module which CarlitoxxPro states needs single
byte I2C reads to the EEPROM.
Pali Rohár reports that he also has a CarlitoxxPro-based V2801F module,
which reports a manufacturer of "OEM". This manufacturer can't be
matched as it appears in many different modules, so also match the part
number too.
Reported-by: Thomas Schreiber <tschreibe@gmail.com>
Reported-by: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
After migration to the shared interrupt support, the KSZ8031 PHY with
enabled interrupt support was not able to notify about link status
change.
Fixes: 59ca4e58b9 ("net: phy: micrel: implement generic .handle_interrupt() callback")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201127123621.31234-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rtl8211f supports downshift and before commit 5502b218e0
("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
the read-back of register MII_CTRL1000 was used to detect the
negotiated link speed.
The code added in commit d445dff2df ("net: phy: realtek: read
actual speed to detect downshift") is working fine also for this
phy and it's trivial re-using it to restore the downshift
detection on rtl8211f.
Add the phy specific read_status() pointing to the existing
function rtlgen_read_status().
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Link: https://lore.kernel.org/r/478f871a-583d-01f1-9cc5-2eea56d8c2a7@huawei.com
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Link: https://lore.kernel.org/r/20201124230756.887925-1-antonio.borneo@st.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use recently introduced PTP_MSGTYPE_SYNC and PTP_MSGTYPE_DELAY_REQ
defines instead of a driver internal enumeration.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace use of magic number with recently introduced define.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all the PHY drivers have been migrated to directly implement
the generic .handle_interrupt() callback for a seamless support of
shared IRQs and all the .config_inter() implementations clear any
pending interrupts, we can safely remove the two callbacks.
With this patch, phylib has a proper support for shared IRQs (and not
just for multi-PHY devices. A PHY driver must implement both the
.handle_interrupt() and .config_intr() callbacks for the IRQs to be
actually used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Also, add a comment describing the multiple step interrupt
acknoledgement process.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Mathias Kresin <dev@kresin.me>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
