NAND, from Boris:
"""
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
SPI NOR, from Cyrille:
"""
- fixes in the hisi SPI controller driver.
- fixes in the intel SPI controller driver.
- fixes in the Mediatek SPI controller driver.
- fixes to some SPI flash memories not supported the Chip Erase command.
- add support to some new memory parts (Winbond, Macronix, Micron, ESMT).
- add new driver for the STM32 QSPI controller.
"""
And a few fixes for Gemini and Versatile platforms on physmap-of
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dxj5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
This patch updates the binding documentation in accordance with
commit 44dd182861 ("mtd: nand: gpio: make nCE GPIO optional")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds documentation of device tree bindings for the STM32
QSPI controller.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The driver sets appropriate DMA mask. Delete the "dma-mask" DT
property. See [1] for negative comments for this binding.
[1] https://lkml.org/lkml/2016/2/8/57
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There are various customizable parameters, so several variants for
this IP. A generic compatible like "denali,denali-nand-dt" is
useless. Moreover, there are multiple things wrong with this string.
(Refer to Rob's comment [1])
The "denali,denali-nand-dt" was added by Altera for the SOCFPGA port.
Replace it with a more specific string "altr,socfpga-denali-nand".
There are no users (in upstream) of the old compatible string.
The Denali IP on SOCFPGA incorporates the hardware ECC fixup engine.
So, this capability should be associated with the compatible.
[1] https://lkml.org/lkml/2016/12/1/450
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The old NAND bindings were not exactly describing the hardware topology
and were preventing definitions of several NAND chips under the same
NAND controller.
New bindings address these limitations and should be preferred over the
old ones for new SoCs/boards.
Old bindings are still supported for backward compatibility but are
marked deprecated in the doc.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
W25Q64 is found on TI's AM335x ICEv2 board. Add it to list
for supported SPI flash devices. This flash can be identified
using JEDEC READ ID opcode.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This can be used to easily identify a specific chip on a system with
multiple chips.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
-----BEGIN PGP SIGNATURE-----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=/fPM
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.11-v2' of git://github.com/spi-nor/linux
From Cyrille:
"""
This pull request contains the following notable changes:
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
"""
Add "mediatek,mt2701-nor" for nor flash node's compatible.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The MR25 family doesn't support JEDEC, so they need explicit mentioning
in the list of supported spi IDs. This makes it possible to add these
using for example:
compatible = "everspin,mr25h40";
There was already an entry for mr25h256. Move that one out of the "keep
for compatibility" section and put in a new group for Everspin MRAMs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This adds device tree bindings for the Cortina systems Gemini
flash controller, a simple physmap which however need a few
syscon bits to be poked to operate properly.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Visually separate register ranges (address/size pairs) in reg prop.
Change DMA channel name, for consistency with other drivers.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Adds the device tree bindings description for Samsung S3C2410 and
compatible NAND flash controller.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add NAND driver to support the Oxford Semiconductor OX820 NAND Controller.
This is a simple memory mapped NAND controller with single chip select and
software ECC.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The generic NAND DT bindings allows one to tweak the ECC strength and
step size to their need. It can be used to lower the ECC strength to
match a bootloader/firmware config, but might also be used to get a better
reliability.
In the latter case, the user might want to use the maximum ECC strength
without having to explicitly calculate the exact value (this value not
only depends on the OOB size, but also on the NAND controller, and can
be tricky to extract).
Add a generic 'nand-ecc-maximize' DT property and the associated
NAND_ECC_MAXIMIZE flag, to let ECC controller drivers select the best
ECC strength and step-size on their own.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Add binding document for the Cadence QSPI controller.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Graham Moore <grmoore@opensource.altera.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Yves Vandervennet <yvanderv@opensource.altera.com>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXg0MnAAoJEGXtNgF+CLcABPcP/jSXHzYUk0vEPNLV6ToaZPgW
+Ct9oQEt6A96M/JOekAo5EyO04wD/CJncXao4ARy7tfvb7MG9bXA7FXsx2ihk22s
npmMV7zOSJisTpYKtX9gI4hJ8Jv8fusm+UIE78NiTJdhbQ/dQrReY7XAyUQin8lV
JIpWRfv2paQeBHn6MLj3MxvNCFxkQhHQOG6ohc2zCkfrQw2rKDWYLnhGLbbTHQV9
kxem+lf5FLk5TxN41NgnVcCfEnxawnNTmbs/i0tj6IqKwFR5fOO6Tcvyi/ZeL75c
3/78hxo3NMVuR9AUqbypbIJZayZiDNQCPpQUcgFbvrToRJoVA8u21+0C/IcKfzZc
mRYtMjU7+PzfbnKOo3IW/6Rbf2kc2q+6p0tMMbjPquWs8oPPRL8HMQu0h+PXXtyw
mz7qVGFjvUUA/vA9ebaUWwXYeHpQ2490wVOhvp523686IZv9kJhhxQWTqTYqCnZK
Ul2+UEYSpNH4ebnOeGbqyYVqee0+zokGMlEQZLyTjsm3rox13MCpOmhr1Qwl480y
fPIb2BLAsXdNqWSo6k7Bg/pTzDoq+i+w3vlKuQnKhOySEnPoV/D4MsAcwx4wkuiD
xxq/bu14vhnxF7Dbmjb3cylhQAz4xJomwixNjGfOg/+AyQQYh1iu0CY026N3F1VV
FmnnhJgQUi3PFGAupMOb
=8Aeb
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.8' of github.com:linux-nand/linux into mtd
Pull NAND changes from Boris Brezillon:
"""
This pull request contains only one notable change:
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
"""
This patch documents the DT bindings for the driver of the Atmel QSPI
controller embedded inside sama5d2x SoCs.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Documentation support for Smart Device Gen1 type of NAND controllers
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Document dmas and dma-names properties.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The 7.2 controller differs in a few area compared to its predecssor (7.1):
- NAND scrambler, which we are not using just yet
- higher ECC levels (up to 120 bits) per 1KB data blocks, also not supported yet
- up to 128B OOB
This patch adds the necessary code to support such a controller
generation and updates the Device Tree binding.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add additional details to the GPMC NAND documentation to clarify
what is needed to enable NAND DMA prefetch.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We've already noticed a few flaws in the MTD work for v4.7-rc1:
* The Atmel folks got ahead of themselves on trying to support their latest
hardware and were working off incorrect documentation. Fix up the NAND
driver to get this correct.
* Fix up device tree example documentation to use the latest recommendations
for describing NAND ECC algorithms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXSH51AAoJEFySrpd9RFgtSnsQAK+UrSM1gFAiMBEWPJuCK100
WZRZG8FxftzGbU33DiSgXDU/RmZBupIBHSZNGoWBkumdd9uozfIWp+s2T40k2ot6
E7ckF3lGaZOWMmzt/MN5lkeTm6Pzs63DemP/a1wSRqfvCTE8kB8EREzUiTQuNnWi
6YMvXuVnwouh5v91vuwKOKmGWuYidy6sF91w8ucd+W/A7p0Rnj8Nr7cGur3Xn+6L
MNjvfvD8tfyKk3b7aaNMyR6oIJQ9awR2TewBbB/6mJQR/eDOPnpq3Z+rJSwEoSJH
Hd/pG0zx9KeZyOF7kbZZmfk9DyPM50qCxiX/Z9kaSMGxyEQgwMjmQslJbDvRGOz5
2s5NAT8Nm3OcedAJgjGLmUlO/NH4XIQt+c35nftikeNplUqNNbZLjMgpfnLWB8FN
5cerUeFBwFZztJIWN1eQfZ7lERwk8bJPr0IRfPASj0xjTXi1DZze7WijA/BrsvEc
rUQ8J1YAXvjVyQZUmJyq8MFVeyEewv1MZ0O5w0t0u7kXtVI3HLQiJCLy1ZD3rDm2
dW4hMVtLOu6WDGZ27a229QtXOEm5L0YXCQGea75zR+gQObiY8mMIN3Qy68W4zSSJ
yGMPY9u8E8oPHh7TeNtc4E8MkYbujqknIshcgTBN2k4HufK6GPZOTvwfor1zdHAe
HGk9MiFRrACPTQIuxfhd
=kb+w
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160527' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"We've already noticed a few flaws in the MTD work for v4.7-rc1:
- The Atmel folks got ahead of themselves on trying to support their
latest hardware and were working off incorrect documentation. Fix
up the NAND driver to get this correct.
- Fix up device tree example documentation to use the latest
recommendations for describing NAND ECC algorithms"
* tag 'for-linus-20160527' of git://git.infradead.org/linux-mtd:
Documentation: dt: mtd: drop "soft_bch" from example
Revert "mtd: atmel_nand: Support variable RB_EDGE interrupts"
This reverts commit 5ddc7bd43c ("mtd: atmel_nand: Support variable
RB_EDGE interrupts")
Because for current SoCs, the RB_EDGE3(i.e. bit 27) of HSMC_SR
register does not exist, the RB_EDGE0 (i.e. bit 24) is the ready/busy
line edge status bit. It is a datasheet bug.
Cc: <stable@vger.kernel.org>
Fixes: commit 5ddc7bd43c ("mtd: atmel_nand: Support variable RB_EDGE interrupts")
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
First cycle with Boris as NAND maintainer! Many (most) bullets stolen from him.
Generic:
* Migrated NAND LED trigger to be a generic MTD trigger
NAND:
* Introduction of the "ECC algorithm" concept, to avoid overloading the ECC
mode field too much more
* Replaced the nand_ecclayout infrastructure with something a little more
flexible (finally!) and future proof
* Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some of
this into their own tree as well
* Prepare the sunxi NAND driver to receive DMA support
* Handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
SPI NOR:
* Start using the spi_flash_read() API for SPI drivers that support it (i.e.,
SPI drivers with special memory-mapped flash modes)
And other small scattered improvments.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXQ9oUAAoJEFySrpd9RFgttf0P/3oIVCvLHSFIsi7XiUusWJWk
Cb+xW3ujFd2kNUqAQGnyvPUGU1amgjAjy2kwMpvpOG07DVgSnxQVGaQLins8Zwpw
auWxH8llISmC6UkNsS1jV0d7KzSMCT2Ne+BenRAn68kq3ovXPPB3B19B6dFj8ail
s83ajoZhsn1+eyctiKtbhXgZWkJHlRmBeXPKAJcS0lBcSibR+6N+O//JEAMnyYvc
7azuw0KMVwQNnNYFAfd9dilV5juZ9bZptTJYH7XuF+44FhxmSKvTX2a9gmp0C4Bm
FszUiPrIWF+t98nSQxxSn/zPlyllFyoisa6F7eGnDHIz+bH0Emf2oVwsSG5ASl42
XTml0kB0jCfuBfgAiyhYU2Uds7rSYs/ZcHr3iPgpUY3Sc3dgoArDdahMJXwqaoa8
UdChu6A+rjhi9PqhzNNVTarbilp3pOVgKAUVEWTdpQ1wGU4c+9SNlTTwhPy4g7RB
uKlqbMeiZ/5rPiihaMUNtzxMxSe9OGYW2HVNVExvmlF2Ca42M1xJJBMlAA6IIXyS
35d3Y4F5zPP7U6GCVla06WHkL5ahXJWmI0Xhf+2jCnDMipeAl6eCEiAJY5EmvAnr
FTpZ4qkspED69mO8oZW9ORje0n6PCm4XPOi4Vl8kci8tlBsEJMk9jaedWwGlZkRk
I5leUP4NEougvuHce2Cn
=J6KN
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
- Rewrite of the unflattening code to avoid recursion and lessen the
stack usage.
- Rewrite of the phandle args parsing code to get rid of the fixed args
size. This is needed for IOMMU code.
- Sync to latest dtc which adds more dts style checking. These warnings
are enabled with "W=1" compiles.
- Tegra documentation updates related to the above warnings.
- A bunch of spelling and other doc fixes.
- Various vendor prefix additions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=s+gW
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Rewrite of the unflattening code to avoid recursion and lessen the
stack usage.
- Rewrite of the phandle args parsing code to get rid of the fixed args
size. This is needed for IOMMU code.
- Sync to latest dtc which adds more dts style checking. These
warnings are enabled with "W=1" compiles.
- Tegra documentation updates related to the above warnings.
- A bunch of spelling and other doc fixes.
- Various vendor prefix additions.
* tag 'devicetree-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (52 commits)
devicetree: Add Creative Technology vendor id
gpio: dt-bindings: add ibm,ppc4xx-gpio binding
of/unittest: Remove unnecessary module.h header inclusion
drivers/of: Fix build warning in populate_node()
drivers/of: Fix depth when unflattening devicetree
of: dynamic: changeset prop-update revert fix
drivers/of: Export of_detach_node()
drivers/of: Return allocated memory from of_fdt_unflatten_tree()
drivers/of: Specify parent node in of_fdt_unflatten_tree()
drivers/of: Rename unflatten_dt_node()
drivers/of: Avoid recursively calling unflatten_dt_node()
drivers/of: Split unflatten_dt_node()
of: include errno.h in of_graph.h
of: document refcount incrementation of of_get_cpu_node()
Documentation: dt: soc: fix spelling mistakes
Documentation: dt: power: fix spelling mistake
Documentation: dt: pinctrl: fix spelling mistake
Documentation: dt: opp: fix spelling mistake
Documentation: dt: net: fix spelling mistakes
Documentation: dt: mtd: fix spelling mistake
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons. For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to
get done.
Finally, reset controller handling as always gets merged through here
as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x+iD
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
Now that we support nand-ecc-algo property it should be used together
with "soft" to specify software BCH ECC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
So far it was only possible to specify ECC algorithm using "soft" and
"soft_bch" values of nand-ecc-mode prop. There wasn't a way to specify
it for a hardware ECC mode.
Now that we have independent field in NAND subsystem for storing info
about ECC algorithm we may also add support for this new DT property.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Document and match the brcm,brcmnand-v6.2 compatible string, the controller has
a register layout identical to the v6.0 version and supports prefetch. Update the
command shift logic to account for v6.2 controller which are the first ones to
use a shift of 0 (6.1 used a shift of 24).
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Standardize the NAND controller/NAND chip DT representation. Now, all new
NAND controller drivers should comply with this representation, even if
they are only supporting a single NAND chip.
Existing drivers can keep support for the old representation (where only
the NAND chip was described), but are encouraged to also support the new
one.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
The GPMC WAIT pin status are now available over gpiolib.
Update the omap_dev_ready() function to use gpio instead of
directly accessing GPMC register space.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Add compatible id and interrupts. The NAND interrupts are
provided by the GPMC controller node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The bindings for the "arm,versatile-flash" device was merged in
commit 3ba7222ac9
"arm/versatile: Add device tree support" but was never used
for anything.
Versatile flash chips are actually just standard CFI chips,
but they have one or two bits in a system controller to control
VPP and write protection. Let's use this compatible string in
conjunction with "cfi-flash" to indicate that we have a
normal CFI flash with some extra Versatile-specific protection.
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add optional properties for QSPI:
big-endian
if the register is big endian on this platform.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
new compatible string: "fsl,ls2080a-qspi".
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As the SAMA5D2 controller supports the 32-bit ECC strength, accept it
as a valid setting when required by the device tree or the NAND
parameter page.
Then configure the controller to use this new setting.
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Starting with the SAMA5D2, there is a new revision of the Atmel PMECC
controller that can correct 32 bits in each sector. This controller is
not 100% compatible with the previous revision that corrected a maximum
of 24 bits by sector, as some register addresses overlap.
Using information from the device tree, we can configure the driver to
work with both versions.
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Do not mention which chips supporting the PMECC controller, as it a
duplicate of the information in the chips' device trees.
Use common terms when describing the sub-node for the NAND Flash
controller.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The NFC controller used to accelerate the NAND transfers on SAMA5 chips
can use either RB_EDGE0 or RB_EDGE3 as its ready/busy interrupt bit.
Use the controller's compatible string to select the correct bit.
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wenyou Yang <Wenyou.yang@atmel.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- Rework and export the changeset API to make it available to users
other than DT overlays
- ARM secure devices binding
- OCTEON USB binding
- Clean-up of various SRAM binding docs
- Various other binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LW4w
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- Rework and export the changeset API to make it available to users
other than DT overlays
- ARM secure devices binding
- OCTEON USB binding
- Clean-up of various SRAM binding docs
- Various other binding doc updates
* tag 'devicetree-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (21 commits)
drivers/of: Export OF changeset functions
Fix documentation for adp1653 DT
ARM: psci: Fix indentation in DT bindings
of/platform: export of_default_bus_match_table
of/unittest: Show broken behaviour in the platform bus
of: fix declaration of of_io_request_and_map
of/address: replace printk(KERN_ERR ...) with pr_err(...)
of/irq: optimize device node matching loop in of_irq_init()
dt-bindings: tda998x: Document the required 'port' node.
net/macb: bindings doc: Merge cdns-emac to macb
dt-bindings: Misc fix for the ATH79 DDR controllers
dt-bindings: Misc fix for the ATH79 MISC interrupt controllers
Documentation: dt: Add bindings for Secure-only devices
dt-bindings: ARM: add arm,cortex-a72 compatible string
ASoC: Atmel: ClassD: add GCK's parent clock in DT binding
DT: add Olimex to vendor prefixes
Documentation: fsl-quadspi: Add fsl,ls1021-qspi compatible string
Documentation/devicetree: document OCTEON USB bindings
usb: misc: usb3503: Describe better how to bind clock to the hub
dt-bindings: Consolidate SRAM bindings from all vendors
...
