Add ability to set rotation via sysfs. The attributes are located in
/sys/class/graphics/fb[n] and accepts 0 - unrotated; 1 - clockwise; 2 - upside
down; 3 - counterclockwise.
The attributes are:
con_rotate (r/w) - set rotation of the active console
con_rotate_all (w) - set rotation of all consoles
rotate (r/w) - set rotation of the framebuffer, if supported.
Currently, none of the drivers support this.
This is probably temporary, since con_rotate and con_rotate_all are
console-specific and has no business being under the fb device. However,
until the console layer acquires it's own sysfs class, these attributes will
temporarily reside here.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for 270-degree (counterclockwise) rotation of the console. To
activate, boot with:
fbcon=rotate:3
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for 180-degree (upside down) rotation of the console. To
activate, boot with:
fbcon=rotate:2
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for 90-degree (clockwise) rotation of the console. To activate,
boot with:
fbcon=rotate:1
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support to rotate the font bitmap. To save on processing time, the entire
fontdata will be rotated on a console switch, then stored in a buffer private
to fbcon. To further save on processing, the fontdata will only be rotated if
the font has changed or if the angle of rotation has changed. Only a single
copy of the rotated fontdata will be kept.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for rotating and positioning of the logo. Rotation and position
depends on 'int rotate' parameter added to fb_prepare_logo() and
fb_show_logo().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch series implements generic code to rotate the console at 90, 180,
and 270 degrees. The implementation is completely done in the framebuffer
console level, thus no changes to the framebuffer layer or to the drivers
are needed.
Console rotation is required by some Sharp-based devices where the natural
orientation of the display is not at 0 degrees. Also, users that have
displays that can pivot will benefit by having a console in portrait mode
if they so desire.
The choice to implement the code in the console layer rather than in the
framebuffer layer is due to the following reasons:
- it's fast
- it does not require driver changes
- it can coexist with devices that can rotate the display at the hardware level
- it complements graphics applications that can do display rotation
The changes to core fbcon are minimal-- recognition of the console
rotation angle so it can swap directions, origins and axes (xres vs yres,
xpanstep vs ypanstep, xoffset vs yoffset, etc) and storage of the rotation
angle per display. The bulk of the code that does the actual drawing to the
screen are placed in separate files. Each angle of rotation has separate
methods (bmove, clear, putcs, cursor, update_start which is derived from
update_var, and clear_margins). To mimimize processing time, the fontdata
are pre-rotated at each console switch (only if the font or the angle has
changed).
The option can be compiled out (CONFIG_FRAMEBUFFER_CONSOLE_ROTATION = n) if
rotation is not needed.
Choosing the rotation angle can be done in several ways:
1. boot option fbcon=rotate:n, where
n = 0 - normal
n = 1 - 90 degrees (clockwise)
n = 2 - 180 degrees (upside down)
n = 3 - 270 degrees (counterclockwise)
2. echo n > /sys/class/graphics/fb[num]/con_rotate
where n is the same as described above. It sets the angle of rotation
of the current console
3 echo n > /sys/class/graphics/fb[num]/con_rotate_all
where n is the same as described above. Globally sets the angle of
rotation.
GOTCHAS:
The option, especially at angles of 90 and 270 degrees, will exercise
the least used code of drivers. Namely, at these angles, panning is done
in the x-axis, so it can reveal bugs in the driver if xpanstep is set
incorrectly. A workaround is to set xpanstep = 0.
Secondly, at these angles, the framebuffer memory access can be
unaligned if (fontheight * bpp) % 32 ~= 0 which can reveal bugs in the drivers
imageblit, fillrect and copyarea functions. (I think cfbfillrect may have
this buglet). A workaround is to use a standard 8x16 font.
Speed:
The scrolling speed difference between 0 and 180 degrees is minimal,
somewhere areound 1-2%. At 90 or 270 degress, speed drops down to a vicinity
of 30-40%. This is understandable because the blit direction is across the
framebuffer "direction." Scrolling will be helped at these angles if xpanstep
is not equal to zero, use of 8x16 fonts, and setting xres_virtual >= xres * 2.
Note: The code is tested on little-endian only, so I don't know if it will
work in big-endian. Please let me know, it will take only less than a minute
of your time.
This patch prepares fbcon for console rotation and contains the following
changes:
- add rotate field in struct fbcon_ops to keep fbcon's current rotation
angle
- add con_rotate field in struct display to store per-display rotation angle
- create a private copy of the current var to fbcon. This will prevent
fbcon from directly manipulating info->var, especially the fields xoffset,
yoffset and vmode.
- add ability to swap pertinent axes (xres, yres; xpanstep, ypanstep; etc)
depending on the rotation angle
- change global update_var() (function that sets the screen start address)
as an fbcon method update_start. This is required because the axes, start
offset, and/or direction can be reversed depending on the rotation angle.
- add fbcon method rotate_font() which will rotate each character bitmap to
the correct angle of rotation.
- add fbcon boot option 'rotate' to select the angle of rotation at bootime.
Currently does nothing until all patches are applied.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the framebuffer mode required for an Apple PowerBook G4
Titanium.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver unconditionally sets xpanstep to 2. However, a value of 4
empirically works better at bpp = 8, and 2 for 16 and 32. This buglet was
exposed by the rotation code.
Second fix is the unconditional call to update_start() without verifying if
the offsets are correct. Remove this call, it's not necessary and secondly,
it causes a crash with invalid values.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/arm/kernel/irq.c:998:26: warning: Using plain integer as NULL pointer
arch/arm/kernel/smp.c:145:25: warning: Using plain integer as NULL pointer
arch/arm/kernel/smp.c:362:5: warning: symbol 'smp_call_function_on_cpu' was not declared. Should it be static?
drivers/video/amba-clcd.c:521:12: warning: symbol 'amba_clcdfb_init' was not declared. Should it be static?
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is the remaining misc drivers/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in misc files in
drivers/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: "Antonino A. Daplas" <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current init code sets hiprilvl to 0 and maxhipri to 5. According to the
specs those values are illegal on both G200 and G400. It also causes
distortions on the TV-out at least when CRTC2 is in YUV mode as is the case
with DirectFB. This patch resets both values to 0.
Signed-off-by: Ville Syrjl <syrjala@sci.fi>
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No point in spamming the logs with a message about xres rounding.
Signed-off-by: Ville Syrjl <syrjala@sci.fi>
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the CACHEFLUSH register on all chip types. The register is listed in all
other specs except 2064W. However I have verified that the register does work
on a 2064W despite being marked reserved in the specs. There were no
noticeable side effects after writing to the register.
Signed-off-by: Ville Syrjl <syrjala@sci.fi>
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add new entries for Mystique AGP with the PCI ID 0x051e.
I don't actually have such boards but according to google they do exist.
Curiosly X.Org doesn't recognize that PCI ID. And what's even more
interesting is that Matrox's own Windows drivers don't recognize it either.
After going through about a dozen different versions I did find one older
driver that does list this particular ID. It is also listed in the pci.ids
file.
I'm not sure if non-220 AGP chips exist. I left the chip revision check
intact for AGP chips nonetheless.
Signed-off-by: Ville Syrjl <syrjala@sci.fi>
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
wait_event_event_interruptible() uses a private wait queue entry so there's no
need for the caller to initialize one.
Signed-off-by: Ville Syrjl <syrjala@sci.fi>
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's the PCI ID for the ATI RN50 chip.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert i810fb, nvidiafb and savagefb to use the fb_find_best_display helper
when searching for the initial video mode.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add new helper, fb_find_best_display(), which will search the modelist for the
best mode for the attached display. This requires an EDID block that is
converted to struct fb_monspecs and a private modelist. The search will be
done in this manner:
- if 1st detailed timing is preferred, use that
- else if dimensions of the display are known, use that to estimate xres and
- else if modelist has detailed timings, use the first detailed timing
- else, use the very first entry from the modelist
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rearrange mode database entries such that preferred timings are entered first,
and less preferred timings are entered last. (Detailed, VESA,
established/standard).
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I converted the "rl" console font from the kbd utility to be a built-in font
for the framebuffer console, and I was wondering if you would be OK with
including it. I've generated a font_rl.c file and related minor
modifications. I find it's the most visually appealing of the kbd fonts which
is why I use it and selected it for conversion. I believe the font is GPL'd.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- The functions for reading the 1st and 2nd bus are essentially the same,
except for the register. Consolidate them all.
- According to Nicolas Boichat, there is an undocumented 3rd i2c bus for
attaching daughter cards. Add support for this.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
vesafb occassionally gets the size wrong when setting the mtrr. When X or DRI
attempts to set the mtrr, it will fail due to range overlap significantly
affecting their performance. Disable mtrr and let the user explicitly enable
it with the mtrr:n option.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initialise the .owner field, so that if the driver is built as a module, the
system has a link to the owner
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the fb_find_nearest_mode() function finds a mode with screen
resolution closest to that described by the 'var' argument and with some
arbitrary refresh rate (eg. in the following sequence of refresh rates: 70 60
53 85 75, 53 is selected).
This patch fixes the function so that it looks for the closest mode as far as
both resolution and refresh rate are concerned. The function's first argument
is changed to fb_videomode so that the refresh rate can be specified by the
caller, as fb_var_screeninfo doesn't have any fields that could directly hold
this data.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use do {} while(0) for empty reverse_order() macro.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some EDID blocks set the flag "prefer first detailed timing" without providing
any detailed timing at all. Clear this flag if the block does not provide
detailed timings.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Attached is a small patch which configures the correct memory clock and
timings on the Elsa Winner 2000 Office pm2 based card. This is necessary when
the card is used on a platform which does not support PC style BIOS
initialization.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by: Jean-Philippe Gurard (Bugzilla Bug 1782)
"I've tried with video=atyfb:debug and video=atyfb:debug,mode:1280x600, \
nomtrr.
In both case, the screen stays black, but seems divided into 4 vertical bands.
Some white lines pop up randomly on each vertical band."
The problem is a combination of an incorrect xclk plus lack of timing
information. The adapter is attached to an LCD device that can do 1280x600
(which is not a standard resolution). The global mode database does not have
an entry for it. Fortunately, the Video BIOS contains the complete timing
info for this display, however, atyfb is not making use of it.
Add support to get the timing information from the BIOS, if available.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix out-of-bounds bug. The pseudopalette has room only for 16 entries, thus,
write only the first 16 entries to the pseudopalette.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove software clipping from imageblit, fillrect and copyarea. Clipping is
not needed because the console layer assures that reads/writes doest not
happen beyond the extents of the framebuffer. And software clipping tends to
hide bugs, if they do exist.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If machine has more than 1 driver installed, and they all drive the same
hardware, it's possible that the driver's fb_release() method will attempt to
restore the hardware state to the initial state. This will leave the new
driver in an undefined state. To prevent this problem, initialize the new
driver by calling fb_set_par() when the old driver is released by fbcon.
Signed-off-by: Antonino Daplas<adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of manually filling up the fields in struct fb_var_screeninfo, use the
display_to_var() helper.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Lot's of redundant code scattered throughout fbcon.c. Consolidate them all
into one function, fbcon_update_softback().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to Jon Smirl, filling in the field fb_cursor with soft_cursor for
drivers that do not support hardware cursors is redundant. The soft_cursor
function is usable by all drivers because it is just a wrapper around
fb_imageblit. And because soft_cursor is an fbcon-specific hook, the file is
moved to the console directory.
Thus, drivers that do not support hardware cursors can leave the fb_cursor
field blank. For drivers that do, they can fill up this field with their own
version.
The end result is a smaller code size. And if the framebuffer console is not
loaded, module/kernel size is also reduced because the soft_cursor module will
also not be loaded.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Prevent spurious recompilations of the radeonfb driver when I2C/DDC support
is not included and i2c header files are modified.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add partial support for GMA900 within the i915GM chipset.
Signed-off-by: Scott MacKenzie <irrational@poboxes.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nvidiafb didn't fully hook-up the code it borrowed from X for doing flat
panel dithering (this is useful for 6 bits panels). This adds a driver
option to force it, and by default "reads" the current value from the chip
to get the firmware setting. It significantly improves the quality of
images on the iMac G5 I have here (though the X driver doesn't yet "read"
the current value and defaults to 0, so you have to add Option "FBDither"
"true" to your X config file to get that, I'll try to fix X.org to "read"
the default unless specified asap).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/video/nvidia/nv_setup.c: In function `NVCommonSetup':
drivers/video/nvidia/nv_setup.c:408: warning: statement with no effect
drivers/video/nvidia/nv_setup.c:496: warning: statement with no effect
drivers/video/nvidia/nv_setup.c:504: warning: statement with no effect
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes nvifiafb mode setting code to be closer to what the X
driver does, which actually makes it work on the 5200FX I have access to.
It also fix the routine that gets the EDID from Open Firmware on PPC, it
was broken in various ways and would crash at boot. Compared to the patch
I posted to linux-fbdev last week, this one just changes a printk to be
closer to the other ones in the driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arrange frame buffer menu:
- puts all Epson drivers together
- removes split of FB_PXA and FB_PXA_PARAMETERS by FB_W100
- results in PXA, W100, Epson, S3C2410, & Virtual FB drivers being
presented at the same menu level as all other FB drivers
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Frame buffer driver help text changes:
- Move S3 Trio next to S3 Savage;
- add or clarify help text for several FB drivers;
- add help text for FB console;
- add help text for bootup logos;
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some visually impaired people use hardware devices which directly read
the vga screen. When newt for instance asks to hide the cursor for
better visual aspect, the kernel puts the vga cursor out of the screen,
so that the cursor position can't be read by the hardware device. This
is a great loss for such people.
Here is a patch which uses the same technique as CUR_NONE for hiding the
cursor while still moving it.
Mario, you should apply it to the speakup kernel for access floppies
asap. I'll submit a 2.4 patch too.
Signed-off-by: samuel.thibault@ens-lyon.org
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Statically allocated devices in module data is a potential cause
of oopsen. The device may be in use by a userspace process, which
will keep a reference to the device. If the module is unloaded,
the module data will be freed. Subsequent use of the platform
device will cause a kernel oops.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Statically allocated devices in module data is a potential cause
of oopsen. The device may be in use by a userspace process, which
will keep a reference to the device. If the module is unloaded,
the module data will be freed. Subsequent use of the platform
device will cause a kernel oops.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
